Extending my network. Time Capsule-Air Express and Extreme.
So currently my network is a time capsule in my basement and an airport express upstairs behind a tv in my living room. I have an extreme that I'd like to use to boost my signal in the back yard where I use the remote app on my iphone to control itunes. They are all 802.11n(?). I would like to place the extreme close to a basement window that has clear sight to the lower back yard area.
What is the easiest way to go about setting this up?
THX
Welcome to the discussions!
+What is the easiest way to go about setting this up?+
Assuming that your AirPort Extreme is the 802.11n version, (it has a square shape), here is how to setup the "extend" configuration with the Time Capsule. The AirPort Extreme must be positioned where it can receive a good signal from the Time Capsule.
I was not clear on whether you already had the AirPort Express setup to extend (you must have an 802.11n version of the Express to allow this), or whether you have it configured to "join" your wireless network for use with AirTunes.
_On the Time Capsule_
Open AirPort Utility
Click Manual Setup
Click the Wireless tab below the row of icons
Make sure that you have a check mark next to "Allow this network to be extended"
Make note of the exact Security setting that you are using
Update to save any changes
The Time Capsule will restart and you should see a green light in 15-20 seconds
_On the AirPort Extreme_
Open AirPort Utility
Click Manual Setup
Click the Wireless tab below the icons
Wireless Mode = Extend a wireless network (If you do not see this choice, hold down the option key on your computer as you click on the selection box)
Wireless Network Name = Exact name of your Time Capsule wireless network. (This should appear as a choice in the setup)
Enter a check mark next to Allow wireless clients
Wireless Security = Exact same setting as your Time Capsule wireless network
Wireless Network Password = Exact same password as your Time Capsule wireless network
Verify Password as above
Update to save changes
The AirPort Extreme will restart and you should get a green light in 15-20 seconds.
Similar Messages
-
Best configuration to extend wifi with Time Capsule & Airport Express
In my house I have a Fritzbox wifi router on the ground floor as my primary internet access. I have an ethernet cable going to the 3rd floor study where the Fritzbox signal is relatively weak. I purchased a Time Capsule as a backup device, but also wanted to extend the Fritzbox wifi network by plugging the ethernet cable in to the TC. I was not successful in extending the network, so I had to create a new network. When moving from downstairs to upstairs, my iphone keeps the connection to the (now weak) wifi network and I have to manually change to the (stronger) TC wifi network.
Additionally, I used to be able to successfully extend the downstairs wifi using my Airport Express (and also managed to have my speakers plugged into this for wireless usage), but do not want to additionally complicate my set-up.
So, what is the best way to connect the following equipment, ideally with the same network name, to ensure I always use the strongrst signal automatically:
Third floor: iMac, Macbook, Time Capsule, Airport Express
Ethernet cable from ground floor to 3rd floor
Ground floor: Fritzbox wifi connected to internetYou must configure the Bridge Mode setting as the very last step before you Update the settings, otherwise the setting will change automatically.
In other words, you can change the setting to Bridge Mode, but if you make any other changes before you click Update, the Bridge Mode setting will not take effect.
Or, if you see any error messages about DHCP conflicts or Double NAT....the AirPort is not in Bridge Mode...even though you might think it is. Check the settings again.
will I still be able to set up an additional 5GHz network in parallel?
Yes -
Dual Band Network: Time Capsule (N only) and Linksys (B/G) Works *Long*
Ok, so this was more tedious than I thought it would be, but things actually seem to be working at this point.
Goal: Create a Dual Band network with Time Capsule (N only) and a Linksys WRTSL54GS (B/G)
Time Capsule: 1000BaseT wired, and 802.11N 5Ghz only wireless
Linksys: 100BaseT wired, and 802.11G 2.4Ghz wireless
Airport Utility 5.3.1
Time Capsule v. 7.3
I set Time Capsule up first, following the step by step directions for "Create a wireless network"
802.11N only, 5Ghz
WPA2 Personal
DHCP 192.168.1.1 (kinda important)
This worked fine-tested on a C2D iMac, both thru ethernet and wirelessly thru N. Time Machine backed up fine.
Now the tricky part, configuring the Linksys.( I just want to mention I had to reset this thing completely about 10 times to get it to work, using a miniscrewdriver)
Starting with a freshly reset Linksys, I connected from my MacBook ethernet port to one of the Linksys ethernet ports (Not the WAN)
I disabled Airport
I logged in to 192.168.1.1 using blank for login, admin for password (default for Linksys)
I did the following:
1) Confirmed Internet Connection Type was "Automatic Configuration-DHCP"
2) Changed Network Setup to "DHCP Server-DISABLED"
3) Turned off the Firewall settings in Security (not sure if this is necessary)
4) Changed the Operating Mode from "GATEWAY" to "ROUTER"
5)Changed the SSID to "LinksysG_ONLY" or something like that
After each one of these steps, I had to save the configuration, thru the Linksys browser interface-which blows.
6) Finally, I changed the Local IP Address of the Linksys from 192.168.1.1 to 10.0.1.251 (thanks to Henry B. for that)
7) And....I no longer had access to the Linksys at all! This stumped me for a while, until...
8) I checked my Ethernet settings (in System Preferences/Network): 192.168.1.1 was set as default router address. But my Router (at least for configuration purposes) was now 10.0.1.251, so it could no longer find it.
9) So I added a new Ethernet port (using the "+" sign), called it Ethernet-Linksys. Set it to Manual. Put in an IP of 10.0.1.250, and a Router IP of 10.0.1.251.
10) I got access to the Linksys setup page again! (Note: I'm sure there is an easier way to do this, but this is how I got mine to work )
11) I set up WPA security again, set it to an unused channel (2 in my case), mixed b/g network.
12) Finally, I moved the ethernet cable from my MacBook directly to one of the ethernet ports on the Time Capsule. I did NOT hook up the other end to the WAN on the Linksys (which for some reason I had done 100 times before) I left it in one of the 4 ethernet ports on the Linksys. Repeat, the WAN (ethernet) port remains empty.
13) I then turned Airport back on the MacBook, connected to "LinksysG_ONLY", and...I was online. And everything seems to work.Hi kjk et al,
I've been searching the boards for something like what you have described in such nice detail. Before Time Capsule, I used a Netgear g router connected to the cable modem and an older Apple base station connected to the Netgear as a bridge. I removed the Netgear and set up my Time Capsule as the primary. The newer computers in my network can access the Time Capsule, but the old Dell with a 802.11g wireless card cannot. I don't remember seeing where I could access TC to change a setting of "N only" or b/g, but I am guessing that it is running N.
I tried to follow the steps you used for Linksys. The pre-step 1 thing, resetting it "10 times to get it to work" - how do you know when it is really reset? With Netgear plugged into electricity, I stuck a paper clip into the hole labeled on the diagram as "restore factory settings" and watched the color of the IO icon change from green to amber to green. I did it again for good measure.
I plugged ethernet from PowerBook G4 into Netgear not-WAN ethernet ports (like your MacBook to Linksys). I disabled Airport. Using Safari, I logged into 192.168.0.1 and got to the Netgear SmartWizard configuration assistant. It says, "No Internet Connection Detected. Please check the connections to the Internet WAN port and cable/DSL modem" - so I looked at your instructions but see no mention of connecting the router to the modem.
Trying to follow your numbered steps...
1. In SysPrefs: Network, Location showed Automatic, Configure showed Using DHCP.
2. I don't see an option in Network to "DHCP Server-DISABLED", but I can choose Configure: OFF. I clicked Apply but browser still gives same message.
I don't know how to continue the steps. -
Extending airport wi-fi network (time capsule airport express)
I have a time capsule linked to my BT cable modem and i have created an apple wi-fi network that I use for my Mac mini and a laptop.
However the wi-fi network doesn't reach the other end of the house, and I am thinking about extending the wi-fi network by adding an airport express.
I have looked at the documents online, but I am not sure of a few things.
Do you need to wire the airport express to your time capsule or another cable modem? (that seems to loose the purpose of wi-fi) as per a document on apple airport networks (p41)? is the only solution a Roaming set-up?
Can t you just plug it in a electricity socket the airport express and add it to your wi-fi network via your network software in system preferences?
thanks for the helpWelcome to the discussions, stephanm8!
The AirPort Express(n) can be configured to "extend" the main wireless network created by the Time Capsule. Here's how to do it.
_On the Time Capsule:_
Open AirPort Utility, click Manual Setup
Click the Wireless tab below the row of icons
Wireless Mode would be set to "Create a wireless network"
Make sure there is a check mark next to "Allow this network to be extended"
Update to save settings
_On the Express:_
Open AirPort Utility, click Manual Setup
Click the Wireless tab
Wireless Mode would be set to "Extend a wireless network". If you don't see this choice, hold down the "option or alt" key on your computer when you click on the selection box. When you select this choice, you should see the network created by the Extreme to "extend".
Enter the wireless password if requested
Make sure there is a check mark next to "Allow wireless clients"
Update to save settings
If you have a dual band Time Capsule the main network can be extended. The guest network cannot be extended.
Once you have the Express configured to "Extend", position it at a point that is approximately 2/3 to 3/4 of the distance between the Time Capsule and the area that you want the Express to cover. You may need to adjust the location of the Express from this general starting position depending on signal strength. -
Airport Time Capsule/Air Express Networking Issue
All of a sudden none of my wireless devices will connect to my network (2 iPhone 5's, 1 iPhone4S and an iPad2). I have a Motorola Surfboard cable modem attached to a Linksys router. Hardwired to the Linksys router is an Apple Airport Time Capsule in bridge mode centrally located in the home to create a wireless network and a Mac mini in the kitchen. Hardwired to the Airport Time Capsule is another Mac mini in the family room and a Windows PC in the walkout. To extend the wireless network I have two Airport Express units at opposite ends of the home. When I use the Airport Utility both of the express units and the Airport Time Capsule will report which wireless clients are currently attached to them, and the clients show wifi as being available with full bars. However, when I try to use any app requiring network all we get is the spinning wheel. If I turn off wifi on the clients LTE & 3G works fine. I have shut down and sequentially started the network up beginning with the modem several times, leaving the system off for longer intervals each time. The DNS servers and domain name are correct and I have even initiated a DHCP lease renewal and restarted the clients with no help. I am guessing my Airport Time Capsule has failed but in no way that is obvious to me. Has anyone had a wireless failure like this? Any suggestions will be appreciated.
This is a follow up from my own post. I factory reset the Airport Time Capsule and the two Airport Express units and re-setup the wireless network leaving the Airport Time Capsule set to 802.11 N (802.11 b/g compatible) and the two Airport Express units extending the first; the network acted the same. I then changed the Airport Time Capsule to 802.11 N (only 5 GHz) and everything works as it used to. I can change it back to "b/g compatible" and it fails, and back to "only 5 GHz" and it works. It would seem the 2.4 GHz radio has failed in a rather odd way. The good thing is my wireless network is working without me having to layout some cash for new hardware. We will see how long the 5 GHz radio lasts, it is a gen 1 Time Capsule. For now all is well.
-
Need help setting up WiFi - Xfinity with Network Switch, Time Capsule, Airport Express and Apple TV
Hello - I recently got Comcast Xfinity service. We had switched from a different service. Our wifi service was never great, but prior to Xfinity, it worked decently. But now that we have Xfinity, our wifi is much worse and very unreliable. I am seeking advice on how to setup my various Apple wifi devices in my home. I have attached a diagram that illustrates what I am dealing with. We have a large old house with stone walls. Comcast does not support this issue.
To explain the attached diagram, we have a total of 4 levels in our house - an unfinished basement, 1st floor, 2nd floor, and 3rd floor. The Xfinity router is in the basement and it is connected to a NetGear 10/100 network switch. I already have ethernet cables running from the network switch in the basement to various locations throughout the house. So I have ethernet connected to my time capsule and ethernet connected to each of my 3 Airport express devices. The dark lines running from the network switch to the various devices represents ethernet cable.
The immediate problem that we are having is that we are unable to connect to our wifi networks. The networks show on my mac laptop and my iPhone, for example, but I am unable to connect. I know that I am inputting the correct password, but most of the time, we cannot get in. Sometimes we can..... Very frustrating! Also, due to the fact that I setup what I have over several years, I have multiple network names. I once tried to fix that issue, but was unable to tackle it due to my lack of understanding.
Here is what I am looking to accomplish:
1. Seamless wifi access throughout our house.
2. One name for our wifi network. Right now we have multiple names for multiple networks. Just want to simplify and have only one network. (I guess that an additional "guest network" would be ok, but not absolutely necessary.
Also, if you think I should disable the Xfinity wifi, and just rely on my mac wifi devices, I am perfectly fine with this. Just tell me how to do so.
I have no idea how where to start or how to set this up. I imagine that I would need to disconnect everything and reset and start from scratch? Can someone tell me what I should do? Even general advice would be helpful, but the more specific, the better, given my limited understanding. Any help or advice would be greatly appreciated.
Thanks in advance!Your photo link is not working. Click on the camera icon to load an image. (Shorten the name of the file to something like WifiNetwork.jpg)
Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
How best to use TWO Time Capsules, Airport Express and Apple TV?
Hello
I have the following Apple equipment and am wondering how best to plug it all together. At the moment I am not using some items at all because I do not know how to best use!
1. MacBook Pro (2012 model) 'Mac1'
2. MacBook Pro (2009 model) 'Mac2'
3. MacBook Air (2011 model) 'Mac3'
4. Time Capsule 1TB (model A1355) 'TC1'
5. (another!) Time Capsule 1TB (model A1355) 'TC2'
6. Airport Express (2008 model)
7. Apple TV (2013 model)
8. LaCie 1TB USB Hard Drive
9. Apple iPhone
10. Sonos system
CURRENTLY
TC1 is plugged into the Virgin Media modem to provide a WiFi network called 'Amer's Apple Network' around the house. The Virgin Media wifi has been switched off to reduce interference.
TC2 is not being used. The Airport Express is plugged in upstairs (or sometimes near garden) to extend the 'Amer's Apple Network' and this seems to work fine.
Apple TV is plugged into main TV and is plugged into 'Amer's Apple Network' directly using Ethernet to TC1 but often runs slowly and does not work if Mac1 is not awake (or iTunes is not running on Mac1).
LaCie is plugged directly into TC1 and currently has a old copy of my iTunes library stored on it which my Sonos system access. However, there seems to be a problem in that iTunes randomly uses that LaCie library and/or local Mac library. Often we get a pop up message on Mac1 saying "Library cannot be found" and we have to manually navigate to the LaCie drive (via the TC1 folder) to open iTunes. Also connecting iPhone to Mac1 seems to work very slowly as it appears to be trying to back up to LaCie drive.
QUESTION
What would be the best, most efficient way of using all (or if some is redundant equipement then which), to set up the following:
1. A shared home network which enables all three computers (and any future Macs and/or iPads etc) to access one master shared iTunes library, which is the one that is updated with any new music, films etc added via any of those machines
2. A shared home network that enables a shared files folder but also allows each user to keep their own personal hard drive (eg locally on whichever machine they are using).
3. A fast (as possible) iTunes back up process when connecting iPhone to computer
4. Usage of both TC1 and TC2 (and Airport Express) to extend network around the house (several weak spots exist) and also to maximise storage using the 1TB of each TC1 and TC2.
5. Would it then also be possible to attach the LaCie USB drive for an additional 1TB storage? If so how and would it be very slow? From existing usage it appears to be very slow when used as a regular access drive, so perhaps better as a 'slow' drive that is just occassionaly used for back up and nothing else
Main question is (to the networking experts!), how would you personally set up all above to give best wifi coverage, fastest back ups, access to Sonos for iTune library, access to Apple TV, and shared folders etc etc. I basically seem to have lots of kit (albeit some quite old) and nothing seems to be working together particularly well.
Happy also to ditch any bottlenecks in the above equipment list (eg LaCie USB drive?) and add something which would better bring together the other components?
Any thoughts much appreciated!
Best
AmerSo ... FINALLY ... I found some time to implement this!
Steps taken and results:
1. Moved my entire music library to Mac1. Used the opportunity to also share my other Mac2 onto HomeShare and copy across any music files from Mac2 onto Mac1 that were not already there.
Result: Mac1 now holds my whole music library locally. Works incredibly fast whenever playing a track, adding a new track or updating info on existing track. Good!
2. LaPastenague's instructions for bridging TC1 with TC2 worked a dream. Only thing is they are basically next to each other as I don't have the energy (or cabling expertise) to install (cleanly) long runs of ethernet cable.
Result: Got a clear Wifi signal, not sure if any faster than before but I assume two TCs next to each other both sending out the same network signal can't be any worse than one. Main thing is that I have an extra 1Tb network drive (i.e. TC2) connected to TC1 which I can access from all my Macs now.
3. Copied the entire Mac1 Music library over to TC2 drive into the Data folder. This happened relatively quickly (I think!) ... but would welcome any comments on whether slower than expected, to highlight if I might be able to improve the connection. 12,000 songs in 2 hours, with Mac1 sending the files to TC2 wirelessly. I know I could probably have connected Mac1 to TC2 by ethernet cable to speed up, but I had run out of Ethernet cables by now!
Result: All my music (as of today anyway) now on Mac1 AND on TC2 in normal readable format (i.e. by Sonos and as a simple back-up that can just be carried around and copied anywhere in the event of loss of Mac1 drive
4. Set up TC2 Music Library in Data folder to be the networked music folder for Sonos using "\\TC2\Data" (ps. why doesn't Sonos allow a simple click and select option for choosing drive and instead force us to go back to the 80s and type in drive path which isn't always clear, especially on a Mac!)
Result: Sonos can access all my music (as of today anyway) on TC2 and no need for Mac1 or any other Mac to be open.
BUT: As you may have guessed, the issue with the above set up is that as soon as I buy a new song, it will get added to my Mac1 quickly and smoothly ... but the area where I really use my music (i.e. Sonos via TC2) will have the older music library.
QUESTION: Is there any way in which I can adjust the above set up, so that whenever I add new music to my Mac1 it also copies across to TC2? Don't mind if this is done slowly and later (eg in middle of night) but of course don't want to have to copy across manually each time. Would prefer it to just update newly added tracks regularly. -
A Time Capsule, Airport Express and AT&T 2Wire walk into a bar...
Alas, I'm sure this question has been asked before, but my reserach keeps turning up separate answers. So I thought I'd turn to this forum for some advice. Ultimately I'm seeks suggestions on various ways to configure my network to allow easy backups, connection two rooms, and wirelessly print from anywhere.
I have a:
Time Capsule (dual band) - used for Time Machine backups
Airport Express (older)
and new 2Wire 3800HGV-B wireless modem/router from AT&T (for U-verse internet/TV)
My room configuration is:
Living room with TV, internet connected DVD player, and new AT&T 2Wire Wireless U-verse modem
Home office with 2 desktop comptuers (no wireless cards) and a USB printer.
Two roaming laptops which move around the rest of the house
The livingroom and the office can't be connected with a physical wire.
What I was hoping to do was setup my office with the Time Capsule in the office as a wired hub, and then use it as a wirelessly bridge to the 2Wire network. But as I understand it, a Time Capsule can't be used as a bridge to a non-Apple product. Please correct me if I'm wrong.
Alternately I could always get wireless cards for the desktop computers, but this leaves the printer.
I've read suggesitons of people who have used their TC as the primary router, disabling wireless on their AT&T 2Wire, and hooking the two together with ethernet. Others who just join the TC to the 2Wireness network. But really what I'm seeking is a way to join the two rooms.
Any thoughts? Am I asking the right questions or providing the right information?
Much thanks,
dana.So I figured I'd go with an initial suggestion and attached my TC via ethernet to the 2Wire modem/router in my living room, and make the TC my primary wireless router.
Good plan
since both will be in the same room, I assume I need to disable wireless on the 2Wire
Correct
What kind of configuration do I need to do on the TC, or do I just following the wizard and select 'Extend existing network'?
You can follow the guided setup or I can give you a step by step manual setup. In either case, you will configure the TC to "Create a wireless network".
("Extend" is only used if the TC connects using wireless only....you will be using Ethernet from one of the LAN <-> ports on the 2-Wire to the WAN port (world icon) on the TC.
The guided setup will normally sense that the TC is connected to another router and suggest that the TC be configured in Bridge Mode, which is the correct setting. Otherwise, select the Bridge Mode option when it is presented.
Note....If you have a newer dual band TC, the Guest Network option cannot be enabled when the TC is configured in Bridge Mode. So, if you want a "Guest" network, maybe the 2-Wire could provide that service.
Should I attach this (via ethernet) to the TC or the 2Wire?
Pick a LAN <-> port on either one, your choice, whichever is easier
What should the AT&T DVR be connected to?
I'm not familiar with an AT&T DVR, but if it connects via Ethernet, you can connect to a LAN <-> port on either the 2-Wire or the TC
For printing, my plan is to attach the printer through USB to the Airport Express and then connect that wirelessly to the TC network (though my first attempt at this failed to connect).
Suggest that you get the TC up and working smoothly. Then tackle the Express. -
Extend wireless network with multiple airport express and netgear powerline
I currently have the following network configuration:
1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
Thanks in advance!
DaveI had a VERY similar problem: I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule. Every time I plugged in the wire to the TC, everything disappeared. Unplugged, and boom. Came back.
Here's how I solved it:
Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it. Then, on the wireless tab select CREATE a wireless network. But, give it the exact same name and password. This is completely counter-intuitive. You would think to choose EXTEND, but this would be wrong. Next choose the network tab. And, select Router mode to Bridge (off).
By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
See if this fixes your issue. Fixed mine instantly. AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out. LOL -
Time Capsule, Airport Express and Xbox Live
Recently I went out and bought a Time Capsule 1TB hoping to extend my wireless network. I knew that Apple products wouldn't usually help extend a DLINK network so it came as no surprise when I could not extend my DLINK network. My solution was to buy a new Airport Express, disable the wifi on the DLINK router and extend the Airport Expresses network via the Time Capsule.
The current situation is: DLINK <-> Ethernet <-> Airport Express Wireless Time Capsule <-> Ethernet <-> Xbox360
The issue is the Time Capsule as far as I can see. For apparently no reason it will change from a solid green status light to a flashing amber status light. Signing my Xbox into Xbox Live seems to be a trigger, but the Time Capsule goes amber even when the Xbox isnt on at all. When it does change to flashing amber I am no longer able to detect it within Airport Utility and as such am unable to diagnose the issue. Any help would be appreciated.Here it works fine. I have a Time Capsule connected to my ADSL modem. I had to buy an all new Airport Express 802.11n, though, because my old AE could not extend my network.
On an all 802.11n setup you just check the "Allow this network to be extended" on the master (Time Capsule), and choose "Extend a wireless network" on the remotes.
The X-Box is connected with an Ethernet cable to the Airport Express, and connection to X-Box Live works fine.
Good luck! -
I have a airport time capsule, an older airport extreme, and an older airport express. I want to hard wire my Mac Mini to the network. What is the best arrangement of the devices? which ones should be hard wired to optimize extending the network?
I am using TM Unifi with an ASUS RT-N18U Wi-Fi router. I would like to know could I use Apple AirPort Time Capsule to extend (repeater, booster) my Wi-Fi to a part of the house where the Wi-Fi signal is poor
Yes,, if you plan to connect the AirPort Time Capsule to the ASUS router using an Ethernet cable connection that will remain fixed and permanently installed at all times.
No, if you were planning to have the AirPort Time Capsule connect wirelessly and extend the Asus WiFi signal, since it would not be compatible with another manufacturer's router for that purpose.
Another way of saying the same thing here would be that if you want to extend the network wirelessly, it will take two Apple routers to do so -
I have a Simultaneous Dual Band Time Capsule. Up until now, I have been extending the network with the Airport Express (2nd Gen, the 802.11n model). Since it was not simultaneous dual band, it was extending over the 2.4 GHz band so as it could extend b, g, and n and support my iPhone at 2.4 n as well as my iPad and MacBook Pro at 5 GHz.
I just bought the new simultaneous dual band unit, which theoreticalkly should be able to extend both bands.
Now, it is not that simple. I also run a guest network, which I assume also gets extended when WDS is on. I also still have the old Express which I have relegated to another part of the house.
When I set up the new Express, it asked me which one of the networks I want to join, either <SSID> or <SSID 5GHz>, the automatically generated name for the the 5 GHz band on the Time Capsule. Which one do I join? How do I know that both are extended? When I connect to the <SSID 5GHz> now my iPhone can see that one and connect to it, so I am assuming it is NOT going at 5 GHz.
And I have no idea at all what the guest network is doing....
Does anyone have any insight into tthe proper way to configure all the units, and what I can expect? My network is as follows:
Airport Express (Simultaneous Dual Band)
Cable Modem > Time Capsule (Simultaneous Dual Band) >
Airport Express (802.11n, last gen)
I want to run guest network (hopefully simultaneous dual band) and personal network. I want the new express to run both bands just like the Time Capsule, and for the old express I want to know which of the two bands I am extending.
Thank You!I also run a guest network, which I assume also gets extended when WDS is on
Unfortunately, the Guest Network cannot be extended.
When I set up the new Express, it asked me which one of the networks I want to join, either <SSID> or <SSID 5GHz>, the automatically generated name for the the 5 GHz band on the Time Capsule.
This likely indicates that the Time Capsule has been setup to use separate names for the 5 GHz and 2.4 GHz bands, instead of the default, which uses the same wireless network name for both bands.
In order for the AirPort Express to be able to extend both bands, the Time Capsule will need to be configured so that both bands use the same wireless network name.
Then, configure the AirPort Express to extend the wireless network name of the Time Capsule, and it will extend both bands. At least, that is the way an AirPort Extreme works, and I assume that the Express is the same. I don't have an Express here to test, but will in another day or two.
The location of the Express is important, since the 5 GHz signals are not as strong as 2.4 GHz signals. You may need to experiment by placing the Express closer to the Time Capsule than normal. With an AirPort Extreme, I find that the Extreme must be located no more than about half the distance from the main router to the area that needs more wireless coverage.
If you continue to use the previous model Express to extend as well, it too must be configured to extend the wireless network name of the Time Capsule. Configured this way, the Express will extend the stronger of the 2.4 GHz or 5 GHz signals, so it will likely extend the 2.4 GHz band unless it is located close to the Time Capsule.
To find out which band the previous model Express is extending, locate a Mac laptop close to the Express and hold down the option key on your Mac while you click on the AirPort icon at the top of the screen. The info displayed will indicate whether you (and the Express) are connecting using 2.4 GHz or 5 GHz. -
Time Capsule Access Control and Extended Network Question
I have a Time Capsule where I have set up a wireless network access list…and extended the network using an Airport Express unit. The Airport Express unit also has settings for an Access Control list. Do these need to be the same as the those for the network from TC that it is extending…or does that happen automatically…and if not what on earth are they for?
Thanks for any help…this doesn't seem clear from what I've read/seen.
JamesI have a Time Capsule where I have set up a wireless network access list…and extended the network using an Airport Express unit. The Airport Express unit also has settings for an Access Control list. Do these need to be the same as the those for the network from TC that it is extending…or does that happen automatically…and if not what on earth are they for?
Unfortunately, they are not automatically applied to each base station in an extended network. You would have to manually enter the exact same list in each base station. -
I purchased a new Time Capsule (2TB - 2013), and I would like to use my old Time Capsule to extend the range of my wireless network. I can't get them to communicate. Any ideas?
You need to use the airport utility on a computer.
If you use v6 utility it is fairly easy and straight forward.
The trick is to place the old TC in the same room as the new one.
Do a full factory reset and then you can just go through the utility to extend wireless network.
I did one post with all the pictures.
https://discussions.apple.com/message/24161378#24161378
If you have issues just ask.
Then you can place the old TC about half way between the new TC and the clients would want to connect.. the half way point is not distance but wireless signal levels.
You can pick that up by using the wireless diagnostics in a mac laptop and walking around to pick up the signals.
This is for extend wireless.. if you want roaming network it is entirely different. That means they are plugged together with ethernet.
Tell us if you mean roaming not wireless extend. -
Hi I've recenty purchased a new imac + time capsule + airport express.
I've set up a new network, rather than extended the current one. How do I change my new network to an extended one or create an extended network?
Michaeldetailed in terms of what focus?
here is a video guide about using the airport utility
http://www.youtube.com/watch?v=65Jv6m43eIE
Maybe you are looking for
-
Questions in relation to iPod nano
Hi, I have a few questions in relation the 5th generation iPod nano and I was hoping to find answers to them here. *Voice Memo* 1. Are there any limitations imposed on the nano's voice memo functionality? For instance, does the nano record up to a pr
-
Multiclip angles show black in angle viewer
All of a sudden my Multiclip angle viewer stopped showing angles. All I see are black frames. Everything else works, I can switch angles etc. Trashed the prefs, deleted renders and rebuilt thumbnails but the problem persists. I opened an old tutorial
-
about a yar ago my ipod went off and wouldnt turn on. i can finallly get it to turn on now but all it will show is a screen of the aple charger with and arrow pointing to the circle itunes app. does anyone know how to fix this?
-
Installed PCI-6025E recognized by Windows XP but only in PXI system by MAX
I installed a PCI-6025E DAQ board on a Windows XP machine. Upon startup it recognized the new hardware and installed the driver from the NI-DAQ 6.9.3 CD. All seemed to work fine. When I try to bring up the device in MAX it only shows up in the PXI sy
-
hi, where can I find ABAP test for certification?