Extending the range of Airport Extreme 802.11n

I have 2 Airport Extremes 802.11n. One of the is connected to a DSL modem and it works fine. I have been trying to use the other one to extend the network, but have not been successful.
I used the exact steps in the manual (Designing Airport Network) published by Apple. The steps I used (several times) were under "Extending the Range of an 802.11n Network".
Whenever I compete the steps and update the base station, the one that I want to use as the extension (not connected to the internet) disappears from the Airport Utility Application and the base station blinks the orange light. I did reset the base station and tried the guide several times but no success.
I am doing something wrong or this manual is not complete. Any help from you guys will be most appreciated.
Thanks!

I have the same problem. I didn't have this issue with the 802.11g version. Are you using the base station in "bridge" mode? Because when I used the "n" basestation in DHCP/NAT mode, it worked fine. Unfortunately, I needed to change to bridge mode for reliability issues with my service provider.
Now I have the same issue as you.

Similar Messages

Extending the range of Airport Extreme in house with walls

Any sugggestions on the best way to extend the range of Airport Extreme? The base unit is located in an office at one end of a house. I would like to be able to connect from rooms at the other end of the house, some 70' away. There are three walls betgween the base and the far room.

I have essentially the same problem, except that our router is a Netgear product (NOT my choice, my husband is a PC guy). I get a great connection when my G5 is on the desk, but if I put it under the desk (which is where I really, really want it) I get nothing.
Will an Airport Express do anything for me? Or do I need to get an AirPort Extreme router? If I get an Airport Extreme router and locate it closer to my computer can I set it up to work with the same cable internet service we have the Netgear connected to? Or do I have to have a totally separate service? My computer is downstairs, the Netgear is up. Moving it is not an option. Our house is wired for cat 5 throughout. (No idea if this matters, I'm clueless on this stuff). Thanks in advance for any suggestions.

How far away can you connect to the internet from Airport Extreme (802.11n)

How far can i take my Laptop away from Airport Extreme (802.11n) and still have internet connection

According to:
http://www.apple.com/au/airportexpress/
They claim the Extreme has a 45m range:
"Suppose you want to connect to the Internet with your PowerBook in an area that lies beyond the 45 metre range of your AirPort Express or AirPort Extreme Base Station"
Will you be using all N devices? G?, B? or a combination?

Help: Using Airport Express to extend the range of Airport Extreme

I am trying to use the Airport Express to extend the range of the network created by my Airport Extreme. The Express works in terms of streaming music from iTunes on the PC connected to th Extreme.
However, I am trying to run a short Cat-5 cable out of the Express to a nearby PC in order to have access to the internet. If the Express is recognized by the Extreme and can play music through connected stereo cables, why can I get an internet connection through the LAN port..??
Here's a real basic representation of my connections...
Cable Modem >>-- Cat5 -->> Airport Extreme >>-- Wireless -->> Airport Express >>-- Cat5 -->>PC#2

To wirelessly extend the range between two AirPorts, you need to configure them in a Wireless Distribution System (WDS).
To facilitate the WDS set up, try the following:
o Perform a "hard" reset on the AirPort Extreme Base Stations & a "factory default" reset on the AirPort Express Base Stations (AX) before setting up the WDS.
o Place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete.
o To avoid having to "switch" wireless networks during the WDS setup, attach each of the remote/relay base station, via an Ethernet cable, to the main base station. Of course, this would be dependent on the AirPort types used for the main/relays/remotes.
o Be sure to jot down the MAC addresses for each of the base stations to be used in the WDS as these will be required during the setup.
o When enabling wireless encryption, configure the relay/remote base stations first and the main base station last.

To extend AirPort Extreme 802.11n

Wanting to extend the range of my AirPort Extreme 802.11n (version 7.4.2)
I have a Airport Express as trial also a 802.11n. AirPort Utility has a lot of trouble finding the Express. When AirPort Utility does find it and I want to set up the Express I have to switch from the Extreme to the Express. Unfortunate side-effect is that AirPort Utility then looses track of the Extreme and I can't "join" the Express as Utility can't find anything to join.
As I have the Express on trial of a friend I did the normal reset (button for 10 sec) and even the factory reset (unplug, press reset button while plugging in) however I did notice it still had his settings. Changed those but as I said before it seems for AirPort Utility is is either or instead of both.

Based on your description, it sounds like the AXn is configured to join the wireless network created by the AEBSn ... not extend it.
The following would be the basic setup steps for extending a wireless network:
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

User Contributed Tips in the AirPort AirPort Extreme (802.11n) forum

*The following User Contributed Tips are located in the AirPort > AirPort Extreme (802.11n) forum:*
adsfushi72 - What does this acronym mean?
http://discussions.apple.com/thread.jspa?threadID=2450065
Publish date: June 4, 2010
William Kucharski - Having issues with your AirPort connection? Please be specific.
http://discussions.apple.com/thread.jspa?threadID=2227197
Publish date: Nov 21, 2009
William Kucharski - Apple AirPort drivers only support a WEP key index of 1
http://discussions.apple.com/thread.jspa?threadID=1654663
Publish date: Oct 16, 2008
*The following related tips are located in other areas of Apple Discussions:*
a brody - Airport, 10.5.8, and MacBook and MacBook Pros and slow internet
http://discussions.apple.com/thread.jspa?threadID=2291464
Publish date: January 7, 2010
Rich Love - Airport and Roadrunner (Jan 6, 2002)
http://discussions.apple.com/thread.jspa?threadID=121815
Mark Lansdown - Semi-wireless Wake on Lan (Oct 8, 2008)
http://discussions.apple.com/thread.jspa?threadID=1276830
Pondini - Using Time MACHINE with a USB drive connected to an Airport Extreme
http://discussions.apple.com/thread.jspa?threadID=2299608
Publish date: January 14, 2010
See also the User Tips Library

Ask yourself a question.
How fast is your internet connection?
If it is is 1-2-8 mb speed then you dont need 'n'.
If you transfer personal info between computers fast speeds allowed up to 54 will save you time.
'n' is to provide greater range like Mimo and increased transfer speeds.
But do you really need it?
No,if you dont transfer huge data,
Yes, if you want to transfer (stream video from your iTV from Mac if you spend most of your day in front of TV.
There is no substitute for a good reliable connection.
In my real world experience because I only have a 8mb ADSL connection 'g' is not the strongest and most reliable scenario to use. During the last airport update my last 3 years of uninterrupted airport connections mixed PC and Macs on WDS set up went belly up and I had posted my thoughts as well with the relevant results and now set up is fine. But at a price.
Downgraded to all on 'b' and now use my Draytek Vigor 2800VG and have AEBS put away in storage.
My signal and range is out of this world. When I decide that I have enough free time to sit in front of a TV and download movies and watch them when I have nothing better to do such as travel the world etc. etc., that is the time I will go for speed...or will I.
Dont get bamboozled by the hype. If you really want one wait for a year then decide. Let others solve the teething problems as is there want.

SERIOUSLY slow USB hard drive on the new Airport Extreme 802.11n

I have recently bought the new airport etreme 802.11n. Great little device, look wonderful on the office desk. I had some troubles getting it up and running on my machine but finaly got there in the end.
The USB hard drive is a great little addition that I was very excited about, untill I got it running. It is amazingly slow, for example I tried to copy a folder that contained 15 files which amounted to 135.6mb and it took 20 mins and 24 seconds to upload!
Is this just the speed that it should be uploading or is there somehting wrong with my settings.
I'm running on 3 bars of signal and the settings I'm using are:
connect with password (which is the same as the base stations password)
Automatically discover disks
Show in menu bar
If anyone knows the technical data for the transfer speeds and can confirm my queries I'd really appreciate it!
Thanks in advance

I have recently bought the new airport etreme
802.11n. Great little device, look wonderful on the
office desk. I had some troubles getting it up and
running on my machine but finaly got there in the
end.
The USB hard drive is a great little addition that I
was very excited about, untill I got it running. It
is amazingly slow, for example I tried to copy a
folder that contained 15 files which amounted to
135.6mb and it took 20 mins and 24 seconds to
upload!
Is this just the speed that it should be uploading or
is there somehting wrong with my settings.
I'm running on 3 bars of signal and the settings I'm
using are:
connect with password (which is the same as the base
stations password)
Automatically discover disks
Show in menu bar
If anyone knows the technical data for the transfer
speeds and can confirm my queries I'd really
appreciate it!
Thanks in advance
Does your drive meet these requirements?:
You can connect USB-based storage devices to an AirPort Extreme (802.11n). Learn which formats and protocols are supported.
The AirPort Extreme (802.11n) supports USB storage devices that have a block size of 512 bytes, and are formatted as Mac OS Extended (HFS-plus), FAT16, or FAT32. Not all USB storage devices use a block size of 512 bytes.
The AirPort Extreme (802.11n) shares storage devices based on the format used to initialize the storage device. For example, if HFS-plus formatting was used, AFP and SMB/CIFS protocols are used to share the device on the network. If FAT16 or FAT32 was used, SMB/CIFS protocols are used.
The AirPort Extreme (802.11n) works with disks that have a single partition and are not RAID volumes (no more than one volume per physical disk).
Note: Use AirPort Disk Utility to discover and mount AirPort Extreme-based volumes over the network.
William

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The wireless router works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The Airport works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

+For now I have it set to Share Public IP address - Is this correct for my Network Setup with The Airport Extreme being the only router being used ?+
This would be the correct setting if the AirPort Extreme is connected to a simple modem (one ethernet port).
*Settings I have Enabled*
5 GHz name indicates that you have elected to use the option to assign a separate name to the 5 GHz network. This will allow you to "tell" compatible computers to connect to that network, rather than the slower 2.4 GHz network
Use Wide Channels is recommended for 5 GHz operation.
Interference Robustness often does more harm than good and should not be used unless you know you are in a area with a lot of wireless networks and you feel that your network is experiencing interference issues from a nearby network.

I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

I'm not sure how to post a message. I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I have an older Airport Express, would it help to install it? would it work best if it was installed in the same room? should it be installed half way in between? Get another Extreme? The Mac Book Pro on the middle floor can see 11 networks in the neighbourhood if that might be causing a problem or would if I installed the Express. Thank for your consideration.

Thanks for your time ... I appologize for the font and colour, I compossed the question in pages and failed to notice the font colour as grey ... there are a variety of computers of various ages so I think it is using a setting that allows both 5G and 2.4 ... the connection to the Airport is thru a cable modem and cable does run throuhout the house ... maybe those hard wires would be a place to look at ... do you think that putting the 'Express' on the second floor might help ... thanks again ...

Airport Extreme 802.11n sharing a disk with a -1 on the mount point

First I have to reboot the device once a day because of the disk that disconnect for no reason like many other on the list ever since I upgraded to 7.2.1 but not sure that as to do with this problem.
Here's is the deal, I have an Airport Extreme 802.11n with a 500GB shared on the USB port. I want to use my iPhoto Library on the 500GB. It's about 11GB, I have tranfered the library over and iPhoto is asking to choose the library I want to use. When I try to point it to the 500GB everything is greyed out. When I use a terminal and do a df command to show the mount point on my computer, I get
/Volumes/500GB-1
Why and where the -1 is coming from?
How can I get /Volumes/500GB only?
One thing I have noticed about the -1 is when I loose the disk connection it prompt me to disconnect 500GB-1 but sometime even with a -2 and -3.
Thx!

can I hook up my printer, scanner and external harddrive through a usb hub?
Partially, a large number of USB printers will work with the AirPort Base Stations' USB port, but not all. I suggest that you checkout the following iFelix site to see if your printer is compatible. Similiarly, most external USB hard drives should work as well.
However, devices that rely on two-way communications, like copiers and scanners, won't work when connected to the USB port.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but the printer won't work with the new one.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but I'm having trouble with the new one. When I try to print, I get a USB Waiting message on the printer, and when I force a page to print by pressing Go on the printer, I get a page that says ERROR: syntaxerror OFFENDING COMMAND: true. . . .cvt . . . fpgm . . . x . . .lglyf . . . <..J head . . . STACK: / [ -mark- /sfnts I’ve tried shutting down the printer and disconnecting it and the Airport, but that doesn’t help. I reset the settings on the printer. I upgraded the Airport firmware and removed, reinstalled, and upgraded the Lexmark printer driver. After I upgraded the firmware and printer driver, a few pages printed correctly, but then I got the same syntax error page as before. Any suggestions for getting the printer to work correctly?

Use a powered USB hub between the AE and the printer.. the usb port does sometimes have issues.
Try deleting the printer in the Mac and reinstall it.. the change in AE can represent effectively a change of printer.. it is important to make sure that is all up to date.
Beyond that.. USB printers.. ughhh! Consider for two toners you can go and buy a proper network printer.

Speed issue with the AirPort Extreme (802.11n)

Hi, I was wondering if anyone could help out with this.
I am the Design Manager and IT Director at a publishing company where we have just upgraded to an AirPort Extreme (802.11n) base station to drive our network. We went this route as all of our machines are Mac Minis with built-in Airport and we were in a situation where re-doing a hardwire on the building was not going to be a possibility due to budget costs.
Our new configuration seems to be running very well and has the following devices connected to the AirPort Extreme:
Linksys Firewall Router (which was used on our old system and was requested by corporate to stay in the lineup to keep the static IP addresses we've already defined for our printers, VPN, etc. intact). The configuration on this part is modem to Linksys router to uplink port on the Airport).
New Panther, Intel based Xserve connected to the Airport's Ethernet port 1.
A 4 port ethernet switch connected to the Airport's Ethernet port 2 which drives four of our HP LaserJet printers.
Ethernet port 3 is not occupied.
All of the ethernet cords connecting our equipment are brand new.
For the most part, everything's been running blazing fast with a remarkable speed increase over our old hardwired setup. However, I've received a few complaints about slow speeds when dragging and dropping and working with files that are stored on our Xserve - we get alot of the "spinning wheel" and the transmission speeds seem very slow.
At present, we have several category 6 ethernet cords on backorder. I was planning on using one to take advantage of the gigabit ethernet capabilities between the Airport and the Xserve (as these are the only two elements of the network that support gigabit ethernet, besides the majority of our Mac Minis. Printers and cable modem are only 10-100 capable, so those will stand as is).
Can anyone tell me if the gigabit ethernet cord will be the solution to this one slow aspect of the new network? Any other settings I could apply to possibly speed up the transmission time when moving files to and from our server? Good news is that every workstation in the house is getting a full 4 bars.
Many thanks!

PS, just wanted to point out that we are also running in bridge mode.
Thanks!

Airport Extreme 802.11n (4th Generation) vs. MBP 2006. The MBP is losing :(

GRRRRRRRRR— I feel like this is a version of a problem I see repeated here endlessly, but none of the threads I see about it is quite the same, or fixes my problem.      We have a network with:
Airport Extreme 802.11n (4th generation), connected to DSL modem. Firmware 7.5.2
MBP 2006, running OS 10.6.7 ****
MBP 2008, running OS 10.5.x
ipads, iphone, shared printer, drive, etc.
Everything works fine EXCEPT the MBP 2006. It connects to the network, works for a while, and then after a certain amount of time (anywhere between a minute and several hours) it's dropped. The menu bar still shows a connection and full signal, but there's no connection (TCP or afp) and when I launch the Aiport Utility, it just says that no base stations can be found.   The menu bar seems to be lying. Using the menu to turn Airport off and back on (or sleeping the laptop) works to reestablish the connection.
I do not have this problem with the MBP 2006 on other wireless networks (at work, or at my other home in another city). Just with the Airport Extreme
I've tried changing the channels, disabling IPv6 on the laptop and on the Airport Extreme, setting up a manual DHCP address, and changing the setting for "radio mode" of the base station from Automatic to 802.11a/n - 802.11b/g/n.   I also read that there might be troubles with "mixed" networks with both 802.11g and 802.11n, so I upgraded the Airport card in my MBP 2006 to an AirPort Extreme 802.11 a/b/g/n, which made disk sharing much faster when it's working, but didn't put an end to the cut-outs
Hjalp? Why does the Airport Extreme keep dropping my MBP 2006 (or vice versa)? Are there other things I should be changing or disabling?

OK, two possible leads:
1) Using the AirPort Utility, I disabled 802.11n, setting the AirPort Extreme to b/g only. This seemed to help— I didn't fall off the network all afternoon. (Setting it to 'n' only did not work, unfortunately, or else that would have been better, since it would have let me take advantage of the faster speeds for Time Machine to the shared disk)
2) Soon thereafter, for seemingly independent reasons, we starting having trouble with our DSL connection. We reset the AEBS to factor settings, which didn't solve the DSL problem (had to get a Windstream technician out for that), but since that reset, I've been connected with 802.11a and the MBP hasn't fallen off the wireless network once.
We'll see how it holds up, but for now, the recommendation seems to be first to reset the AEBS settings to factory default, and then try disabling 802.11n...

I have a Airport Extreme 802.11n and I can't find the disc to install it... how can I install without the disc?

I have a Airport Extreme - 802.11n and I'm trying to install it -- but I don't have the disc. Any help would be so appreciated.

You don't need the disk, you can download and install the application that you need.
If you are using Windows 7, the link for the software is just below. Otherwise, post back to let us know what operating system your computer is using.
AirPort Utility 5.6.1 for Windows - Apple

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

Plenty of suggestions.. only you can find out which one is correct.
What model AE? What firmware?
Since Panasonic TV is not apple it will use SMB windows type networking.. everything but Apple does.
Are the names in the AE all SMB compatible.. ie short.. max about 20 characters.. no spaces and pure alphanumeric.
Is the security set to WPA2 Personal with a pure alphanumeric password of 10-20 characters.. more is fine if you suffer paranoia but isn't needed.
Fix the wireless channels.. so it doesn't flip flop like a dying fish.
There are only 3 channels for 2.4ghz that do not overlap, 11, 6, 1 although someone suggested 8 works well if you have heaps of interference. If you live in flat/apartment building you have heaps of interference.
Lastly is it stable if the distance is 3M direct line of sight?
If not then get a high power wireless AP and use that instead.

Extending the range of Airport Extreme 802.11n

Similar Messages

Maybe you are looking for