Extending Wireless Network w/ Airport Express?

I'm attempting to extend my network to other rooms in my apartment. I have an Airport Express (for the iPad) next to my iMac in one room. I am trying to add a second AE in the living room so I can get a better signal to stream Netflix. However, I don't have ethernet in the living room. Is it possible to use the second AE to act as a relay to extend my wi-fi from the origianl AE? They are both new AE devices... Thanks in advance for your help!

You need to configure the second AirPort Express to "extend a wireless network".
Apple's instructions for this type of setup are here:
http://support.apple.com/kb/HT4259
Although a second AirPort Extreme is shown in the illustration, the setup of the AirPort Express is exactly the same.

Similar Messages

Extend wireless network with AirPort Express

How to extend the wireless network with AirPort Express and Belkin PlayMax as the primary router ?

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

Extending Wireless Network with Airport Express / DLink Wireless

I have a DLink wireless router WBR-1310. I own two Airport Express 802.11n's. Can anyone help me out with how I can properly set-up an extended network with these products? All help is greatly appreciated.

You would need one AirPort Express located near the D-Link router and connected to the D-Link with an ethernet cable. This Express would be configured to "create a wireless network" and "allow this network to be extended"
If you have two areas that need more wireless coverage, you would locate an AirPort Express approximately 1/2 the distance between the "main" AirPort Express and the area that needs more wireless coverage.
Then do the same with the second area that needs more coverage.
Without knowing your room layout, I can't honestly tell you whether you need only one "extending" Express or more than that.
It will help to remember that the "extend" setup works like the hub and spokes of a wheel. Your "main" Express connected to the D-Link would be the "hub". Each of the "extending" Express devices would be at the end of a spoke. The Express devices at the ends of the spokes communicate directly to the hub, not to another Express at the end of another spoke.
So, to work well, hopefully your D-Link router and Express will be located in a central area of your home so the extending devices will work around the perimeter.
I would recommend that you study Apple's support document on extending wireless networks before you make a final decision on what to do.
http://support.apple.com/kb/HT4145
Finally, consider if you can connect the two Express devices you have now back to the D-Link using ethernet cables. This would provide much better performance than a wireless only situation.

Extend Wireless network with Airport Express via Cat6 cable to Cisco E4200 router.

Hello there! Totally new to this, but I've been doing a lot of research, and have been getting conflicting answers, so maybe someone can help me out. I've been reading that you cannot wirelessly extend your network unless you have a time capsule or an airport extreme. However on some forms, if you have the airport express hard wired to the router(in my case a Cisco E4200), you should be able to extend your network. Is this accurate? If so, can someone please post steps on how to do this? Thanks!

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

Extending wireless network using airport express

Greets all,
I'm trying to extend a wireless network in a two-storey apartment using TC and Airport Extreme.
The current setup is based on a Netgear N300 wireless router, which works fine upstairs but the signal is too weak to be useful downstairs. I have at my disposal a first-gen Time Capsule (TC) and a couple of Airport Express (AE) stations as well. I'd like to be able to extend the wireless network downstairs but of course the AEs won't talk directly to the Netgear router, so I'm guessing I need to use the TC somehow.
So far I've tried using the TC in bridge mode as well as a separate network via ethernet from the Netgear router, both of which worked but didn't extend the range - nor did it allow me the option of extending the TC network. In fact, all the searching I've done hasn't unearthed a solution to extend a wireless network using TC where TC is not the primary router.
Any help appreciated. I'm sorry if I haven't included all the necessary info off the bat.
Airport Utility 6.3.1 installed.

They are necessarily in fairly close proximity to each other (due ethernet cable).
If the Netgear and TC are in close proximity to each other, there is really no reason to have both devices providing the same wireless signal......and a very real possibility that there will be wireless interference between the two products.
My suggestion and instructions assumed that the Time Capsule would be at least a few rooms away from the Netgear. If the close proximity setup does creates some issues, then it will be necessary to turn off the wireless function on the Netgear router.
Unfortunately, the older A1088 version of the Express cannot be used to extend the wireless network since it has no settings for that type of application.
Locate the A1264 about half way between the TC and the general area where you need more wireless coverage.
Power up the A1264 Express for a few minutes, then hold in the reset button on the device for 10 seconds and release. Allow a full minute to for the Express to restart to a slow, blinking amber light.
Open up AirPort Utility
Click Other WiFi Devices
Click on AirPort Express
The utility will open up automatically and take a minute to analyze the products, then suggest that the Express be configured to "extend" the TC network.
Enter a device name that you want to use for the Express and click Next
The utility will set up everything for you. When you see the message of Setup Complete, click Done.
That's it.

How do I extend an existing wireless network using airport express?

Hi all,
I am trying to extend existing wireless network using airport express, my main router is Belkin

Unfortunately, Apple's "extend" feature is designed to only work with other Apple routers if you are trying to "extend" using wireless only.
It is extremely unlikely that this feature would work with a router from another manufacturer using wireless only.

Extending my Linksys Wireless Network with AirPort Express

I would like to add an Airport Express to my wireless network to extend my wifi range and add AirPlay to my home theater system. Can Airport Express be used to extend my current wireless system that is not an Airport Extreme devise?
Also, by adding the Airport Express does this now limit the number of devices I can have on my wireless network to the 10 even if the Linksys supports 50?
Thanks for any advise...

Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your non-AirPort router can be extended wirelessly with the AirPort Express Base Station (AX).
The few that are known to work are:
another Airport Express Base Station
802.11g Airport Extreme Base Station (AEBS)
802.11n AirPort Extreme Base Station (AEBSn)
Linksys WRT54G or WRT54GS (not v5)
Belkin F5D7230-4 and F5D7231
BT Voyager 2091
Netgear WGR614 v6
Buffalo WGR-G54

How do i use my time capsule and extend the network with airport express

I have a new iMac and Time Capsule, how do i extend the network with airport express. My time capsule does have a guest net work, and logins and passwords? I am no computer person. So for me it would have to be spelled out.

Use the search as this has been done to death ..
Bob Timmons is the expert on this.. look at his answers here.
https://discussions.apple.com/thread/4274187?start=0&tstart=0
https://discussions.apple.com/message/21856077#21856077
This has been automated in the v6 utility. I am used to doing it manually in v5 utility which is also fairly easy.
Apple doco is also good to read.
http://support.apple.com/kb/HT4145
http://support.apple.com/kb/HT4259
Note.
You cannot extend the guest network unless everything is up to date 7.6.3 firmware. And that is only with the TC as the main router in the network.
All apple routers can be configured as the main wireless or as the extend wireless.. so don't worry if a post uses express or extreme or TC.. they are for wireless, the same thing.

How do I know "Roaming Network" is working with Airport Express and Airport Extreme and should I use extended wireless network for third Express?

Attempting to eliminate a dead spot in Wifi coverage [and implement AirPlay] have one Airport Extreme 802.11n and two Airport Express 802.11n's.
http://support.apple.com/kb/HT4145
The Airport Extreme is of course connected to cable modem and Ethernet switch, and one Airport Express is connected to the Ethernet network. As per instructions for creating a "Roaming Network", Airport Express is set to same SSID, security type, and Password.
Questions:
1. How does the client device know which Airport to connect to? In other words, will it switch to the closer WiFi transmitter automatically? The WiFi reception problem is intermittent in the fringe areas so what I do not want it for it to stick with the more distant Airport Extreme in the basement when the Airport Express which is closer will work better.
2. How can I tell which of the Airports the attached client device is using?
The third Airport Express will be in a third location - I was planning on using it also for expanding coverage but after reading the warnings about performance suffering when purely using WiFi for the expansion in this location ("Wireless Extended Network" without an ethernet connection) I have figured that the single wired Airport Express will be adequate and will use the third Express to do Airplay only.
http://support.apple.com/kb/HT4259
Question: Can I use this second Airport Express to extend the wireless network via "Extended Wireless Network" while the other two are in "Roaming Netowrk" configuration? Without bogging down??
Mitch

1. How does the client device know which Airport to connect to?
The Mac computer will automatically connect to the wireless access point with the strongest signal...which is probably the closest AirPort. An iPhone or iPad may not do this and will tend to stay connected to one AirPort.
2. How can I tell which of the Airports the attached client device is using?
On a Mac, open Macintosh HD > Applications > Utilities > AirPort Utility. Click on one of AirPorts. In the area to the right, locate the AirPort ID and jot that down. Then do the same for your other AirPort.
Move your Mac near one of the AirPorts and log on to the wireless. Hold down the option key on the Mac while you click the fan shaped AirPort icon at the top of the screen. Look for the BSSID. That is the AirPort ID of the device to which you are connected.
If you are close to the "remote" AirPort, and you see the AIrPort ID of the "main" router when you are testing, then you know that the network is not configured correctly.
Can I use this second Airport Express to extend the wireless network via "Extended Wireless Network" while the other two are in "Roaming Netowrk" configuration? Without bogging down??
There will be a modest 10-15% bandwidth loss with the "extend" setup, assuming that the Express is located where it can receive a strong wireless signal from the AirPort to which it is associated. You can avoid the bandwidth loss if the Express is also connected via Ethernet as part of the roaming configuration.

I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network. I select Extend Wireless network but have no success. Ideas?

I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal. The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available. I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play. I got the plug, but no play. I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status. I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times. Then wait 45 seconds and the default settings will return. I did all that, only to find out that after the initial flash of green, green never appeared again. I got a fast flashing yellow light, followed by the light going off. Apparently this didn't reset it properly. So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
highFly376

Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule

Extending Gen 1 Time Capsule Wireless network with Airport Express N

I am having difficulty setting up my new Airport Express w/ 802.11N (SKU# MB321LL/A) to extend the wireless network from my Time Capsule (SKU# MB276LL/A).
My setup is as follows:
Time Capsule is connected to Cable modem with the following wireless settings:
Wireless mode -> Create a Wireless Network
Allow this network to be extended -> Checked
Radio Mode ->802.11n (5Ghz N only)
Wireless Security -> WPA2 Personal
The issue is the when I attempt to setup the AE to extend the network. I match the settings to the Time Capsule:
Wireless Mode -> Extend a Network
Select the Time Capsule Network
Allow wireless clients -> Checked
Wireless Security -> WPA2 Personal
However after I reset the AE the LED glows Amber and the following problem is reported:
+Wireless Network+
+This AirPort wireless device is set up to join a specific wireless network that can't be found. If you don't see the network that you want to join in the Network Name Pop-up menu, enter the network name and network password if necessary to try again.+
When I check the Airport->Wireless tab the settings were as before.
Any thoughts on this? Thanks.

Welcome to the discussions!
Have you tried to position the AirPort Express close, say 10-15 feet, as a test to see if it will connect that way?
If so, then move it back another 10-15 feet, etc.
5 GHz signals do not travel well or penetrate surfaces very well, so my first thought was that the signal was not strong enough for the Express to pick it up where you had it located.
Message was edited by: Bob Timmons

Setup for extending Sky wireless network using Airport Express or Time Cap

Hi,
Hi,
I have three Mac computers/laptops (iMac, MacBook Air and G4 PowerBook), all currently functioning via airport on a sky wireless network (Sky HD Sagem router) all backing up wirelessly to a Time Capsule 1TB which is also connected to the same wireless Sky network. At the top of my house signal strength is weak as you would expect. I would like to be able to extend the range of the sky routers signal which is on the ground floor (3 storey house). My original idea had been to setup a AirPort Express on the 2nd floor to extend the network, but I am unsure what steps I have to follow and whether I need to create a WDS network or not? I've seen some comments that say Sky & Apple hardware are not compatible and it's not possible to extend a Sky router/wireless network using a Apple Airport Express or Time Capsule. Can someone provide me with a step by step set of instructions on what I need to do to set this up? If a work around is required, again any advice would be very much appreciated!
Many thanks,
Eugene

Welcome to the discussions!
Sky and Apple products are not compatible for the purpose of extending your network using wireless only.
If you could connect an ethernet cable from your Sky router to the AirPort Express, or if it's not possible to run an ethernet cable...take a look at a pair of ethernet powerline adapters to accomplish the same task by using the AC wiring in your home to transmit the ethernet signal.
If you configure the AirPort Express to "create a wireless network", this would in effect, extend your network by adding an AirPort Express that would be configured with the exactly the same wireless network name, security settings and password as your Sky router. The AirPort Express would also need to be configured as a "bridge".
Post back if you need more details about something like this.

How can I extend my wireless network using Airport Express and an Airport Extreme on BT Infinity?

I have BT Infinity and I am using the Time Capsule with Airport Extreme as my router. Working well (even on wireless). I want to extend the wireless network with an Airport Express, but I cannot work out the settings necessary in Airport Utility. I am using Mountain Lion 10.8.2 on a Mac Pro. Please help!

BT,
I've read several of your posts, thanks for taking the time to share your wealth of knowledge.
I'm in a situation similar to the one described by 'scoutusmaximus'. Seeking the flexibility of a standalone router, I finally upgraded my 4-yr old ATT DSL gateway (modem+router) to a Comcast standalone modem + the ASUS RT-AC66U: http://www.asus.com/Networks/Wireless_Routers/RTAC66U/
Typically, I stick with all things Apple but the ASUS router seemed fairly superior to the current-gen base station (on paper, anyway; time will tell when it comes to performance) so, for once, I jumped ship. My plan was to extend the ASUS wired/wireless network using my TimeCapsule and 2 Airport Expresses in bridge mode, however, a google search turned up several unhappy customers that claim those devices don't play well with non-Apple routers, especially when it comes to 'extending' a network.
Questions:
1. Can I successfully extend the wired/wireless network created by the ASUS router using the 3 airport devices listed above w/out negatively impacting performance? I'd rather have 1 wireless network as opposed to creating a new wireless network with the TC and then extending it with the AP Expresses... though I'd consider that option down the line if it came to that.
2. Will the LAN ports on the TimeCapsule remain functional?
Btw, my house is wired so, I can reach all 3 devices via ethernet cable coming off of a central, managed switch. Supposedly, you only lose the LAN ports on the TC if you extend wirelessly.
Any advice would be appreciated.

Extend a non Airport wireless network with Airport Express

I want to use an Airport Express to extend a wireless network which is not an Airport network. The wireless is being provided by a wireless router. I tried setting up WDS, but that requires a wireless network. How do I extend the wireless network without it being an Airport Base Station? Can I?
Thanks.

I'm trying to extend an 802.11g network. The base access point is a SpeedTouch which supports WDS. My Airport Express happily connects to the network as a regular node, but I can't get the WDS to work. Do you know of a way to set this up?
Thanks!
JP

Extend existing wireless network with airport express..impossible?

I have tried to extend my existing wireless network with an airport express, but it seemd that I always need a ethernetcable...apple support insured me it is possible but the airport utility software only allows me to extend using a cable it seems....

Couple of thoughts here.......
The AirPort Express will only extend a wireless network if you have another Apple router providing the wireless network to be extended.
Is your "main" wireless router an Apple product? If yes, what model number do you have?
It would also help if we could get the model number of the AirPort Express. Some older versions are not capable of extending a wireless network.

Extending Wireless Network w/ Airport Express?

Similar Messages

Maybe you are looking for