Extending wireless network with an aiport express

I have a netgear wireless router set up in my house on the second floor, but my room being located on the first floor i get a poor signal so i bought an airport express to extend my network. i tried going through the aiport exress setup assistant but that wouldnt work, so i ended up hooking it to my netgear router on the second floor to set it up in airport admin utility and then brought it back down to the first floor. my itunes worked with the speakers for about.. ten seconds then stopped. and my signal is just as weak as before.. any suggestions?

Unfortunately, it is simply not possible to use an Airport Express to wirelessly "extend" the wireless range of any model of Netgear wireless router. Netgear's wireless routers do not support Apple's implementation of a wireless distribution system (WDS), which is a necessary requirement for setting up an extended wireless network with the Airport Express. And no - it doesn't work the other way around either (Airport Express as base station, Netgear wireless router to "extend").
It sounds like you did successfully configure your Airport Express to "join" your existing wireless network - which will allow you to print and stream iTunes to the Airport Express. The problems you are having with Airtunes "hanging" on your Mac are almost certainly due to the poor wireless signal quality problem that you are already aware of.

Similar Messages

Extend wireless network with multiple airport express and netgear powerline

I currently have the following network configuration:
1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
Thanks in advance!
Dave

I had a VERY similar problem: I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule. Every time I plugged in the wire to the TC, everything disappeared. Unplugged, and boom. Came back.
Here's how I solved it:
Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it. Then, on the wireless tab select CREATE a wireless network. But, give it the exact same name and password. This is completely counter-intuitive. You would think to choose EXTEND, but this would be wrong. Next choose the network tab. And, select Router mode to Bridge (off).
By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
See if this fixes your issue. Fixed mine instantly. AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out. LOL

I am unable to join my existing wireless network with new AirPort Express

I am unable to join my existing wireless network with new AirPort Express.
I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
Any suggestions? Thanks in advance.

Welcome to the discussion area!
It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
Power down the AX
Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
Release the reset button after 10 seconds
When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
Do you know the exact security type that your D-Link router is using? That is the key element in the process.
Open AirPort utility, click Manual Setup
Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
Click the Wireless tab
Wireless Mode....Join a wireless network
Wireless Network Name...must exactly match your D-Link wireless network name
Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
Wireless Password...must match the D-Link network
Click the Music icon to enable AirTunes
Click Update to save settings
Any luck?

Unable to create a wireless network with my airport express. Please help!

I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
Any ideas? Thanks in advance for your help.
Tom

Is the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ... or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?

Extending an existing wireless network with an airport express

My wireless signal is quite weak in my room so I'm looking for a way to extend the range of the network by using an airport express. I understand i can't do this wirelessly but is it possible to run an ethernet cable from my existing router to the airport express in my room and then have a stronger signal in my room?
Thanks in advance!

Welcome to the discussion area, Aaron!
If you connect an ethernet cable from your existing router to the AirPort Express, and then configure the Express to "Create a wireless network" with the same name, security settings and password, this will in effect, extend your current wireless network.
The Express must be configured as a "bridge" to operate correctly on your network when you do this, meaning that the setting for Connection Sharing on the Express will be set to "Off (Bridge Mode).

Extend wireless network with AirPort Express

How to extend the wireless network with AirPort Express and Belkin PlayMax as the primary router ?

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

Extending Wireless Network with Airport Express / DLink Wireless

I have a DLink wireless router WBR-1310. I own two Airport Express 802.11n's. Can anyone help me out with how I can properly set-up an extended network with these products? All help is greatly appreciated.

You would need one AirPort Express located near the D-Link router and connected to the D-Link with an ethernet cable. This Express would be configured to "create a wireless network" and "allow this network to be extended"
If you have two areas that need more wireless coverage, you would locate an AirPort Express approximately 1/2 the distance between the "main" AirPort Express and the area that needs more wireless coverage.
Then do the same with the second area that needs more coverage.
Without knowing your room layout, I can't honestly tell you whether you need only one "extending" Express or more than that.
It will help to remember that the "extend" setup works like the hub and spokes of a wheel. Your "main" Express connected to the D-Link would be the "hub". Each of the "extending" Express devices would be at the end of a spoke. The Express devices at the ends of the spokes communicate directly to the hub, not to another Express at the end of another spoke.
So, to work well, hopefully your D-Link router and Express will be located in a central area of your home so the extending devices will work around the perimeter.
I would recommend that you study Apple's support document on extending wireless networks before you make a final decision on what to do.
http://support.apple.com/kb/HT4145
Finally, consider if you can connect the two Express devices you have now back to the D-Link using ethernet cables. This would provide much better performance than a wireless only situation.

How do i extend my network with a airport express

How do I extend my network with mt airport express

Hi Tesserax, I'd like to join this discussion. It seems Jasonbeyer didn't reply, but I have a question related to his.
I'd like to extend the wireless signal from my Cisco Model DPC/EPC2202 VoIP Cable Modem (802.11n) to the living room where, at the moment, it is non-existent. I assume there's inteference or the signal cannot reach through the concrete walls and rooms leading up from my bedroom to the living room.
My question is:
I'm thinking of extending my wi-fi signal by using the Airport Express and simultaneously using it to connect to my hi-fi to play iTunes from my bedroom's iMac.
Something's telling me it's not going to be that easy. I'm using an iMac (7,1) if that's any help or clue.
What are the things I should take note of and will Airport Express be compatible with my modem? Would I have to get TWO Aiport Express to bridge the signal to my living room?
Thank you everyone for your time. Cheers!
Kane

Extending My network with three Airport Express or buy an Airport Extreme?

I live in a large three story house and currently have it wirelessly networked using two Airport Express' but my signal is very weak on the third floor and in other spots throughout the house.
Would it be possible to buy a third AE and extend the network that way or would I be better off buying a AEBS?
Any thoughts or suggestions would be greatly appreciated.
Thanks

It will really depend on the construction materials used in your house or any other forms of Wi-Fi interference that could prevent a clear wireless signal. Both routes, you suggested, will have it advantages and disadvantages.
Extending the existing network wirelessly using a WDS, effectively, cuts the throughput in half for each base station in the chain...so, in this case the second AirPort Express Base Station (AX) (acting as a WDS relay base station) would only get half that of the first AX (acting as the WDS main base station). In turn, the third AX (acting as the WDS remote base station) would receive half of the second's throughput. The good news is that you should have a strong signal across each of the AXs, just lower throughput the farther along in the chain.
The 802.11n AirPort Extreme Base Station (AEBSn) has a greater range than either the older 802.11g version or the AXs. You may find that it will provide enough to cover you entire house. In the off-chance that it doesn't, you can still use it to create a WDS between AEBSn and your current AXs.

I have an airport extreme and am trying to extend the range of the wireless network with an airport express. I set it up with the help of apple support, both lights are green on both airports, but the range didn't change. What could be wrong?

I am trying to extend the range of my wireless network by adding an airport express to an airport extreme. I configured it with the help of apple support, but it hasn't changed the range that I can access the internet wirelessly in my house. What could be the problem? Does weather affect the wireless network??

So, on the Extreme you checked the box to "allow this network to be extened" ?
Correct?
And on the Express, you set it up to "Extend a wireless network" ?
Correct?
See this Apple article and see if you missed anything...
http://support.apple.com/kb/HT4145
To learn about other options for expanding your Wi-Fi base station wireless network and things you should consider before expanding your network, click here.
Set up: Components of an extended network
➊ Primary Wi-Fi base station (this is the base station connected directly to the Internet)
➋ Extended base station
Configuring a wireless extended network
To create a wireless extended network, you must place any extended Wi-Fi base stations within range of the primary Wi-Fi base station.
Start with the device that will be configured as the primary Wi-Fi base station. Then configure your extended Wi-Fi base stations, ensuring that each is within direct range of the primary Wi-Fi base station.The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.

How to extend range of my wireless network with an Airport Express connected by ethernet with Airport Utility 6.0

Hi everyone,
I have AirPort Express 802.11n (1st Gen) firmware 7.6.1, that is connected to my main wifi base station (a TimeCapsule) by ethernet. I would like to extend the range of the Wifi Network but am not clear on how to do so using the new interface of Airport Utlity 6.0.
Does anyone have any tips on how to do this?
BR
AK

Hi Everyone!
Many thanks for the tips. I have downloaded 5.6 and have set my Airport Express in the "Extend a wireless network" mode. I was still having a few problems with the quality of the wifi connection in different parts of my apartment (by no means a very large one, but walls seem to be made of extra dense concrete here in Singapore) and went out and bought a few powerline adapters by TP Link (http://www.tp-link.sg/products/details/?categoryid=1862&model=TL-PA211#spec).
If you don't mind a slightly long post, I would be very grateful for any tips:
My setup is now as follows:
Main room
Time Capsule - connected to a Cisco DPC3925 Modem (http://www.cisco.com/web/consumer/support/modem_DPC3925.html) both connected to a TP Link adapter 1.
iMac - connected via Ethernet to TP Link adapter 2 and wifi enabled
Airport Express 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1) used to stream audio to a stereo that doesn't have an optical cable input. Since it is an Ethernet connection, I have wifi turned off.
Apple TV 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1)
Bedroom A
Airport Express 2 - connected via ethernet to TP Link adapter 3
Bedroom B -
Apple TV 2 - connected by Ethernet to a TP Link adapter 4
After following the tips on setting up the extended wifi network, I find that when I use a wireless client (e.g. iPad, Macbook air, etc) in either Bedroom B or Bedroom C (both don't have wifi in the room) the connection is very poor. Even more odd is that the connection in Bedroom A, one that does have Airport Express 2. To be clear when I mean very poor, I mean Skype/facetime skips frames and freezes... this doesn't happen when I am in the main living area.
I would be very grateful for tips on how to set up the most robust network given the configuration above. Specifically, I am wondering about:
When I select Extend a wireless network option on Airport Utility 5.6 the summary page states that it is connecting using "Wireless Network" vs what I would expect it to say "Ethernet connection".
Is there any advice on whether to enable 5Ghz network and if so, should I try to use that for the various wifi clients?
Does anyone know if I can somehow use Apple products to extend the reach of the Cisco DPC3925? Frustratingly the signal is quite strong (compared to Apple routers), but I cannot properly stream audio/video if that wifi network is used (as my iMac that hosts the content is on the Apple one... and I'd have to walk over to switch it to the Cisco one).
Any other tips would be much appreciated!
Cheers!
AK

Extend Wireless network with Airport Express via Cat6 cable to Cisco E4200 router.

Hello there! Totally new to this, but I've been doing a lot of research, and have been getting conflicting answers, so maybe someone can help me out. I've been reading that you cannot wirelessly extend your network unless you have a time capsule or an airport extreme. However on some forms, if you have the airport express hard wired to the router(in my case a Cisco E4200), you should be able to extend your network. Is this accurate? If so, can someone please post steps on how to do this? Thanks!

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

Extending wireless network with Express

Hi all
We recently renovated and got the house wired with ethernet to almost every room. Currently the signal comes through a Motorola router/modem and connects to the ethernet network.
I am broadcasting a wireless signal via the Airport Extreme, and everything works great except that the range does not cover one end of the house. I have an Airport Express that I'd like to set up in order to extend the range of the signal. My understanding is that simply doing this wirelessly (where the express picks up the existing signal and rebroadcasts) isn't all that effective. I'd like to connect the Express to the ethernet network and broadcast the same wireless network as the Extreme.
Will that work?
So basically both the Extreme and the Express will be connected directly to the Motorola modem. Can they both broadcast the "same" network? or does the Extreme have to be connected directly to a port on the Express for this to work?

My understanding is that simply doing this wirelessly (where the express picks up the existing signal and rebroadcasts) isn't all that effective
Correct.
I'd like to connect the Express to the ethernet network and broadcast the same wireless network as the Extreme.
Good plan.
So basically both the Extreme and the Express will be connected directly to the Motorola modem
A true "modem" has only one Ethernet port, so that would not work. Better to connect from the WAN "O" port on the Express to a LAN <-> port on the AirPort Extreme.....even if the "modem" is a modem/router or gateway with more than one Ethernet port.
Can they both broadcast the "same" network?
Yes, this is known as a "roaming network".
Your next question might be how to set this up. The answer depends on the AirPort models that you have and what operating system you are using on your computer.
Check on the bottom of the AirPort Extreme for the model number....starts with an "A" followed by four numbers. The model number on the Express is on the side or bottom of the device. It also will read "Axxxx".
If you have a Mac and are not sure what operating system it is using.....click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X Version number that you see there.

Having trouble with extending an Apple wireless network with a AirPort Express

Trying to extend the range of my AirExtreme with a AirExpress:
I get stuck when the AirPort Utility ask is I'm sure I want to switch networks. if I select switch I loose the AirExtreme. If I select don't switch it take me back to the beginning. Any help will be appreciated.

You have to "switch" networks to be able to pick up the signal from the Express and configure it with new settings.
Once the Express is configured it will become part your existing network when you see a green light.
Then, switch back to your regular wireless network on your Mac and everything will be on the same network

Extend wireless network with Airport Extreme n and Airport Express g

I have a 4th generation Airport Exteme (n) and an older Airport Express (g) and would like to use the Airport Express to extend my network to the other end of my house, where the signal is very weak. When I tried to set it up tonight, my Airport Extreme disappeared all together and I had to do a hard reset to get it back. I am using a macbook pro 2.4 GHz Intel Core 2 Duo running OS X 10.7.2. Are there any current insturctions to do this?

Here's a Youtube video of how to do it. http://www.youtube.com/watch?v=e3EdbRfX1_w
I had the same set up you do. I did not have success with the Express g. And in my case I had much better success when I sold the Express g on ebay, bought an Express N from the refurb store, so it only cost around $20 get something that is much more reliable.
I quickly tried to find an Apple Support tech note for you but didn't, post back if you need more.

Extending wireless network with an aiport express

Similar Messages

Maybe you are looking for