External Cache Error

I have Motherboard MSI K7N2 Delta ISLR and CPU Athlon XP 2500+ Barton, RAM 1 x 512 Kingston DDR 333 Value RAM.
The problem, External Cache option in BIOS is disabled for correct function the OS, if enabled External Cache option the system crash in the boot the OS.
CPU is Brong? this is in BOX.
Motherboard is Brong?
I have not other CPU or Motherboard for test.
Help Me.

Your ssytem don't have any external cache, its all onboard on the CPU its self. Why do you want to enable it? Is the machine stable and going ok with is disabled? Use a CPU ID Tool to verify the CPU's internal cache.

Similar Messages

ARP cache error

We have a SBS 2003 server running with a standard dual network configuration. One card for accessing the internet and the other card to connect the server to the local network.
We frequently lose our internet connection for an unknown reason (although the other card is fine and all client computers are still able to access the server -- they just loose internet access.)
We also receive the 'Clearing the ARP Cache' error message when trying to repair the connection.
However, instead of rebooting the server, we simply go into the Network Connections, locate the card that is for the internet connection, right-click and choose 'Disable', and then after it is disabled, right-click and choose 'Enable'.

Hi,
Before going further, would you please let me know if you have configured RRAS on your server? Based on your description, the problem can be caused if you are using RRAS as your basic firewall/NAT.
Please try the following suggestions to see if the problem can be resolved.
1. Firstly, we should make sure whether the network setting is correctly and properly configured. Please re-run CEICW Wizard on the SBS Server, it helps us automatically configure the network
settings, you can refer to this step-by-step article to finish the wizard:
How to configure Internet access in Windows Small Business Server 2003
http://support.microsoft.com/kb/825763/en-us
2. Please double check if you have correctly configured your DNS settings.
a. Leave the Default Gateway of the internal NIC blank on the SBS Server.
b. Configure both the internal NIC and the external NIC to use the internal DNS Service as the DNS Server.
c. On the DNS Server, create the DNS Forwarder to forward the external DNS resolution requests to the ISP's DNS
d. On the DNS Server, delete any public IP that is being registered in the local DNS.
3. Type "arp -d *" (without the quotation mark) from the command prompt. Then try repairing the network card again. If error still occurs, please turn to step 4.
4. Try turning off the "Routing and Remote Access" service, it can cause this problem.
a. Click Start->Run, type "services.msc", go and find "Routing & Remote Access", right click it and choose Properties.
b. Set start-up type to disabled and stop the service.
c. Then restart the computer which is mandatory in this case.
d. Try repairing the network card again, any luck?
If the problem persists, please help me gather the following information:
1. Does everything work normally before? If so, what changes have you made to the server/clients before the problem occurred?
2. Make sure that you uncheck "register this connections in DNS" check box from external NIC.
3. Confirm the connection binding order.
a. Please open Control Panel -> network connections.
b. Click Advanced -> Advanced settings
c. In the adapters and bindings tab, make sure that the internal adapter is on the top.
For your information:
A Description of the Repair Option on a Local Area Network or High-Speed Internet Connection
https://support.microsoft.com/kb/289256/en-us
Hope it helps.
Best Regards,
Andy Qi
Andy Qi
TechNet Community Support

Install cache error

I'm trying to install itunes 10.6 on windows 7 home premium. it downloads the software and starts to install. I receive an error: "an error occurred while attempting to create the directory c:/program data/apple/installer cache" I click retry several times and no luck so I have to click cancel and it rollsback the installation. I have downloaded a new copy of the installer from another computer and receive the same error. I dropped the UAC on the system to none. That did not work, it give me the same error. I have tried renaming the Installer Cache to a temp name and when installing again, I the error says it doesn't have the permissions to create the directory. I have gone into the control panel and attempted to repair bonjour, itunes, apple mobile device support, apple software update and quicktime and all of them have reported "The system cannot find the file specified." I have tried running the install package with the right click Run as Administrator and the install cache error still occurs. I have check the security on the file and it has my user name and full control on the parent and all items below.
When I plug in my iphone or ipod, it asks about updating to 5.1, I click download only. I then receive an error window "There was a problem downloading the software for the iphone or ipod. The network connection could not be established"
I don't know if the two problems are related. I'm at a stand still have have no other ideas of what to try next. What suggestions might you have to solve this problem?
Thanks for the help!
Joel

I tried to rename the apple computer folder to _old and I received another error with another really funky folder name that looked like a SID. I renamed that and reran.
Crikey. Probably that number (in the folder name) was the SQUID ("squished GUID") for the iTunes installation (or possibly one of the other associated components being installed). In addition to the error 5, that brings us to a total of three of the more exotic things that could possibly happen in this sort of file-access-problem context.
So, excellent work on your part getting past all that. Many thanks for reporting back with your resolution, too.

Cache error message in Adobe Bridge CS6

I am continuing to get a cache error message despite purging the cache several time on different occassion via the Preferences. Adobe Bridge now seems to be frozen on Building Criteria. The platform I am using iMac OSX 10.8.5. I have rebooted the machine a couple of times to no avail. Any advice

If Windows, search your event viewer for something like "The device \Device\Ide\iaStore0 did not respond within the timeout period." Since this
is kind of a hardware issue, there might be a similar thing happening on MACs. If you see this warning check what driver you are using for Intel
Rapid Storage Technology. I was using version 10.x and the latest from Intel is 12.x. Intel cautions you not to use this updated driver without
checking with the system manufacturer, which in my case, Asus, maintained that 10.x was the latest approved driver. I installed the 12.x driver
directly from Intel despite the warning, and the problem seems to have been resolved. I post in case this gives someone else a clue to solve
this nagging problem.
Oh, this might be particularly significant if you have recently installed a larger hard disk.

Error when loggong on for external ID "": Error during SAML 2.0 logon

Hi,
I'm getting be below error when trying to use SAML SSO for a ABAP Webdynpro page on a NW 7.4 system. When I access the page, it redirects to the identity provider, comes back to the page and it shows the logon page. I'm looking for any ideas of things I could look at.
N SAML20 SP (client 400): Incoming Response
N SAML20 Binding:          POST
N SAML20 IdP Name:         http://xxxxxx/adfs/services/trust
N SAML20 Status Code:      urn:oasis:names:tc:SAML:2.0:status:Responder
N SAML20 SP (client 400): Default ACS endpoint: https://xxxxxx/sap/saml2/sp/acs/400 , old default ACS endpoint
N SAML-Trace: CALL 'SAML login': SY-SUBRC = 222 , PWDCHG = 0
N *** ERROR => SAML-Trace: Path = /sap/bc/webdynpro/sap/oauth2_authority [sign.c       16519]
N {root-id=005056AD26DF1ED4B69880FF4BE51F68}_{conn-id=005056AD26DF1ED4B69880FF4BE53F68}_1
N *** ERROR => SAML-Trace: Returncode = 222 [sign.c       16519]
N *** ERROR => SAML-Trace: Message class = SAML number = 011 [sign.c       16519]
N *** ERROR => SAML-Trace: Message = Error when logging on for external ID "": Error during SAML 2.0 logon [sign.c       16519]
I have updated the service to use alternate logon procedure and added the handler CL_HTTP_EXT_SAML20
I have added the identity provider through transaction SAML2, but it does not seem to be working.
Here is a decrypted SAML assertion:
<samlp:Response ID="_9c844d84-8117-4851-8270-aeb12e935daf"
Version="2.0"
IssueInstant="2015-04-02T00:21:06.477Z"
Destination="https://xxxxxxxxx/sap/saml2/sp/acs/400"
Consent="urn:oasis:names:tc:SAML:2.0:consent:unspecified"
InResponseTo="S005056ad-26df-1ed4-b699-c4c630853f68"
xmlns:samlp="urn:oasis:names:tc:SAML:2.0:protocol"
>
<Issuer xmlns="urn:oasis:names:tc:SAML:2.0:assertion">http://xxxxxxxx.com/adfs/services/trust</Issuer>
<ds:Signature xmlns:ds="http://www.w3.org/2000/09/xmldsig#">
<ds:SignedInfo>
<ds:CanonicalizationMethod Algorithm="http://www.w3.org/2001/10/xml-exc-c14n#" />
<ds:SignatureMethod Algorithm="http://www.w3.org/2001/04/xmldsig-more#rsa-sha256" />
<ds:Reference URI="#_9c844d84-8117-4851-8270-aeb12e935daf">
<ds:Transforms>
<ds:Transform Algorithm="http://www.w3.org/2000/09/xmldsig#enveloped-signature" />
<ds:Transform Algorithm="http://www.w3.org/2001/10/xml-exc-c14n#" />
</ds:Transforms>
<ds:DigestMethod Algorithm="http://www.w3.org/2001/04/xmlenc#sha256" />
<ds:DigestValue>08HK08VLpJC23JoQs+p+oHbDBvjRF+9NwBeowmlFTrY=</ds:DigestValue>
</ds:Reference>
</ds:SignedInfo>
<ds:SignatureValue>xxxxxxx</ds:SignatureValue>
<KeyInfo xmlns="http://www.w3.org/2000/09/xmldsig#">
<ds:X509Data>
<ds:X509Certificate>MIIFPjCCBCagAwIBAgIHAMFKH58TFzANBgkqhkiG9w0BAQsFADCBtDELMAkGA1UEBhMCVVMxEDAOBgNVBAgTB0FyaXpvbmExEzARBgNVBAcTClNjb3R0c2RhbGUxGjAYBgNVBAoTEUdvRGFkZHkuY29tLCBJbmMuMS0wKwYDVQQLEyRodHRwOi8vY2VydHMuZ29kYWRkeS5jb20vcmVwb3NpdG9yeS8xMzAxBgNVBAMTKkdvIERhZGR5IFNlY3VyZSBDZXJ0aWZpY2F0ZSBBdXRob3JpdHkgLSBHMjAeFw0xNDAxMjMxOTM3MThaFw0xNzAxMjMxOTM3MThaMEIxITAfBgNVBAsTGERvbWFpbiBDb250cm9sIFZhbGlkYXRlZDEdMBsGA1UEAxMUZnNwcm94eTItZGV2LmlndC5jb20wggEiMA0GCSqGSIb3DQEBAQUAA4IBDwAwggEKAoIBAQDAM13/bboldFRmDGK3QBbxlDREoGuQEUWeroZCDM/tH7Rk+AjgXbc4pkon13EwKi7q9brzkBMCY3HH9Ep2BUHjopydy+AWQH9vjLK2wXD/+6T4FCG1i8Kt+lRrcxRWUugnBuK+BRgxEJDz7ap8KvcRk6ERWQrx5Co8K7ey5nEqjapCDJQg3Yrkxo2pEWGBKSIXXmpU+CgK03y4HOW19/rmdcyLThjchn+Jgxe8obL4tiVk4D/X36wOqtV/1cnIjGak/px/p1oQEGD5PC7F3FIZConhUu7PJDLmioqdGcimZvFiZK6xQJyzy90lm0dHRT1qhkC9TTsGvAAMCh/gn41xAgMBAAGjggHEMIIBwDAPBgNVHRMBAf8EBTADAQEAMB0GA1UdJQQWMBQGCCsGAQUFBwMBBggrBgEFBQcDAjAOBgNVHQ8BAf8EBAMCBaAwNgYDVR0fBC8wLTAroCmgJ4YlaHR0cDovL2NybC5nb2RhZGR5LmNvbS9nZGlnMnMxLTExLmNybDBTBgNVHSAETDBKMEgGC2CGSAGG/W0BBxcBMDkwNwYIKwYBBQUHAgEWK2h0dHA6Ly9jZXJ0aWZpY2F0ZXMuZ29kYWRkeS5jb20vcmVwb3NpdG9yeS8wdgYIKwYBBQUHAQEEajBoMCQGCCsGAQUFBzABhhhodHRwOi8vb2NzcC5nb2RhZGR5LmNvbS8wQAYIKwYBBQUHMAKGNGh0dHA6Ly9jZXJ0aWZpY2F0ZXMuZ29kYWRkeS5jb20vcmVwb3NpdG9yeS9nZGlnMi5jcnQwHwYDVR0jBBgwFoAUQMK9J47MNIMwojPX+2yz8LQsgM4wOQYDVR0RBDIwMIIUZnNwcm94eTItZGV2LmlndC5jb22CGHd3dy5mc3Byb3h5Mi1kZXYuaWd0LmNvbTAdBgNVHQ4EFgQUMRTW5O0fpR4kET2ED84QAS6ZXBowDQYJKoZIhvcNAQELBQADggEBAKCQfnSSA1gs6qyYKqAqQKhhRRhC4wMtZJLZUmMGPe2q+QM4dQxJgrFy2OVG6I4dXFrxINGlPdJVVXBKtLn9Fm2t0Cb8lAV3rLruEfRJTDK6MeDFOD5qXgU4higpuDGrAmqKvMIOk7VJA0gPbW4lasgqGQXzOspZCmCIWwOqcIDZRr0wo09QLidegr/phjZMzuy8IO0U1w7U6MX767qcl3RGcqRwpquMtMiaw5ROx9v3DK3JOemlqQwKy/uzzBohzYln6AYim8cnZMvfaKDLYNwE0+Rg6nmemlf6PXOjE3Uisc71v3uFstWsXzUPhDeQlycFzPDT4t4srIaxdMrEs3w=</ds:X509Certificate>
</ds:X509Data>
</KeyInfo>
</ds:Signature>
<samlp:Status>
<samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Responder">
<samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:NoPassive" />
</samlp:StatusCode>
</samlp:Status>
</samlp:Response>

Hi Brian,
I am not sure but you could check below thread and couple of sap note.
Single Sign On - Sharepoint 2010 to SAP using ADFS
1799402 - Automatic account creation for SAML 2.0 SP
1257108 - Collective Note: Analyzing issues with Single Sign On (SSO)
It may help you to resolve / identify the cause of the issue.
BR
AKJ

Win 8.1 Lock Up After 5 min, "Memory Management" or "Cache Error"

Systems blue screens every few minutes. MS offered a variety of error messages, now is uniformly "Memory Mangement". Chrome shows a Cache Error.
Any ideas?

Hello again TexasBooster,
It is good to hear from you again!
To contact our technical support, please call at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

URGENT Bridge and cache error photo corrupted NEED HELP

We were going to edit a photo and upon opening it and error came up and said: "edit bridge encountered a problem and is unable to read the cache. please try purging the central cache in cache peferences to correct situation"
We solved the cache problem by purging it but the photo is corrupted! Furthermore, the photo turned red and 1/3 of the photo has been mysteriously turned black! It only briefly returns to normal after cache problem in adobe bridge. It turns normal but only for a split second!!! WE NEED THIS PHOTO RESTORED TO ORIGINAL CONDITION BEFORE THE CACHE ERROR.
Thank you for help

Your photo may be lost, I'm sorry to say.
Check your Windows System Event log and look for disk errors. Disks do fail, and if there have been unrecoverable errors you'll see them in the event log.
A failing disk is not something to be left alone. I hope you have a recent backup - if not, make one right away, then replace any failing disk drive ASAP, or you chance losing more data. I always recommend high-reliability enterprise class disk drives such as Western Digital RE4. They're not that much more expensive, and lost data can be worth a lot.
-Noel

IMac G5 won't boot, external interrupt error

I started my iMac G5 and did get the chime but it automatically goes into OF mode. The fans run loudly and it continously scrolls an "external interrupt" error with a bunch of jargon that goes by so fast I can't read it.
I tried resetting SMU, none of the bootup key sequences work, I can't boot from disk and it won't go into target disk mode. I've searched online "external interrupt" which has been an issue for others, but haven't found an answer to the problem yet.
I just tried resetting SMU again. This time I got the chime again, but now have a black screen. After about 30 seconds of nothing the fans start running and the screen remains black. Help please!

Worth trying a few more times:
Resetting the SMU on a G5 iMac:
http://support.apple.com/kb/HT1767
and on resetting the PMU on a Power Mac G5, G4 and G3 :
http://support.apple.com/kb/HT1939?viewlocale=en_US
http://support.apple.com/kb/HT1436

External Cache Failure reported and computer won't boot

I have a highly upgraded Digital Audio G4 (originally a single processor 533 Mhz, now a Dual 1.2 Mhz). The machine has been running through many ups and downs hangning in there for a while. Basically everything has been upgraded except the motherboard. Normally, this machine runs like a champ and I changed nothing on it when it started behaving erratically. It just sat powered off for a while.
The latest problem ocurred out of the blue:
After being powered completely off for some hours, when I went to boot it back up, everything came on like it normally does (fans, power light, hd's sound like they're running etc.), but it would not boot. My monitor would just go into power save mode and display nothing. When the computer does this, I cannot reset PRAM nor can I boot into Open Firmware. There are no chimes and the PRAM does nothing. My keyboard does not respond to any external stimuli, it will not boot off the original CD. No keyboard input affects the way it boots. It is as though the computer powers on but starts up nothing.
The only thing I have been able to do to get it up and running is to hit the black PMU reset button on the motherboard. If I do this before powering on, then the machine boots up as normal. When I actually shut down and lose power to the motherboard, then later try to reboot, it goes through this process again and again - monitor goes into powersave mode, no PRAM reset abilities, nothing boots, sits powered on only, etc. If I open the case, hit the PMU button, close the case and then restart, the Mac behaves as normal... UNTIL you shut it down and try to power it up, then it goes through this process until the PMU is reset.
First thing I did was replace the battery with a fresh new one that I have. The computer behaves exactly the same. I have tried resetting PRAM when it boots back up, have tried resetting NVRAM when it boots back up. None of this changes the behavior.
I was at a loss with this and tried disconnecting my external devices which did not change the behavior.
The reason I now believe it has something to do with the External Cache is as follows:
I have two versions of Mac OSX on two different drives. In System Profiler, Panther told me nothing was unusual. All devices including RAM seem to be okay. When running System Profiler in Tiger, I found a new item in the list called "Diagnostics".
Under Diagnostics, there was this very perculiar message: "Power On Self Test - Result FAILED, Failure Type - External Cache".
What does this mean? Is there a way to fix this? I am sure that it's related to my problem, but what are viable solutions?
G4 Dual 1.2 / PB 1.5 Mac OS X (10.3.9) running Tiger & Panther, 1.25 GB RAM

I have narrowed this down to an issue with my 3rd party Gigadesigns CPU upgrade. Though it worked flawlessly for about a year and a half, it now does not like being powered off. Works fine if you leave it on, but to reboot after a power down, the PMU must be reset. PIA! But at least it works. But it fails to get past POST (Power On Startup Tests) without the PMU.
By replacing my original 533Mhz CPU, the power off problem disappeared. Of course, that's not an optimal solution, so now I either keep the machine on all the time or it's PMU time.
Hope this helps someone down the road...

Firefox 5 seems to cache error redirects.

Firefox 5 seems to cache error redirects.If for example I get redirected to a 404 then fix the problem with the site, it will still redirect me to the 404.

Try to Reload web page(s) and bypass the cache.
* Press and hold Shift and left-click the Reload button.
* Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
* Press "Cmd + Shift + R" (MAC)

Cat c6509 E with Supervisor vs-s720-10g reload and Cache error detected!

Can you help me Cat c6509-E reload
connect console I see :
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image : ############################# [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_sp Software (s72033_sp-IPBASEK9-M), Version 12.2(33)SXI1, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sat 28-Mar-09 10:48 by prod_rel_team
Image text-base: 0x40101328, data-base: 0x421FFA10
Cache error detected!
CPO_ECC (reg 26/0): 0x000000B6
CPO_CACHERI (reg 27/0): 0x84000000
CP0_CAUSE (reg 13/0): 0x00004800
Real cache error detected. System will be halted.
Error: Primary data cache, fields: , 1st dword
Actual physical addr 0x00000000,
virtual address is imprecise.
Imprecise Data Parity Error
Imprecise Data Parity Error
22:12:30 UTC Tue Mar 24 2015: Interrupt exception, CPU signal 20, PC = 0x413EB310
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
-Traceback= 414EDA90
$0 : 00000000, AT : 42510000, v0 : 00000000, v1 : 00000001
a0 : 43757CC4, a1 : 00040110, a2 : 45762ECE, a3 : 00000000
t0 : 44997CF0, t1 : 00000000, t2 : D5303A40, t3 : 00003A40
t4 : 0000004F, t5 : 0000005F, t6 : 68C8F600, t7 : 00000000
s0 : BEDA4010, s1 : 00000000, s2 : 00000000, s3 : 44086D60
s4 : 45762ECC, s5 : 00000001, s6 : 00000080, s7 : 44080000
t8 : 45762ECC, t9 : 00000000, k0 : 841E6970, k1 : 02951800
gp : 4250FC60, sp : 44997D48, s8 : 4499848E, ra : 413EB310
EPC : 414EDA90, ErrorEPC : 413EB310, SREG : 3400F105
MDLO : 00159DC0, MDHI : 00000000, BadVaddr : 00000000
DATA_START : 0x421FFA10
Cause 00004800 (Code 0x0): Interrupt exception
File bootflash:crashinfo_20150324-221230 Device Error :No such device
%Software-forced reload
22:12:30 UTC Tue Mar 24 2015: Breakpoint exception, CPU signal 23, PC = 0x4171F5E0
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
-Traceback= 4171F5E0 4171D184 40F4F26C 40F4F450 40F4F670 4171282C
$0 : 00000000, AT : 42510000, v0 : 441D0000, v1 : 424C0000
a0 : 00000000, a1 : 00008100, a2 : 00000000, a3 : 00000000
t0 : 0000FF00, t1 : 3401FF01, t2 : 41712918, t3 : FFFF00FF
t4 : 41712918, t5 : 73206265, t6 : 65746563, t7 : 20546865
s0 : 00000000, s1 : 424C0000, s2 : 00000000, s3 : 08000000
s4 : 42380000, s5 : 42380000, s6 : 41D90000, s7 : 00000001
t8 : 506D5CC4, t9 : 00000000, k0 : 00000000, k1 : 00000000
gp : 4250FC60, sp : 50012420, s8 : 41D90000, ra : 4171D184
EPC : 4171F5E0, ErrorEPC : 413EB310, SREG : 3401FF03
MDLO : 00000000, MDHI : 00000003, BadVaddr : 00000000
DATA_START : 0x421FFA10
Cause 00000024 (Code 0x9): Breakpoint exception
=== Flushing messages (22:12:30 UTC Tue Mar 24 2015) ===
Buffered messages:
Queued messages:
*Mar 24 22:12:30.695: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
Firmware compiled 19-Feb-09 20:18 by weizhan Build [100]
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Error address Lo=0x4010
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Error address Hi=0x1EDA
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Interrupt Hi reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Interrupt lo reg=0x8000000
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-DUMP: System controller Global Registers Dump
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: global hazard reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: soft reset cfg reg=0x10FFFF
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: global cfg reg=0x20
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: init status reg=0x8
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl cfg reg=0xE
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: prio map cfg reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ecc error log reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: parity error log reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: jtag idcode reg=0x5013102F
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: work status reg hi=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: work status reg lo=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: eobc rxstat reg=0x11FE
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: eobc txstat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: eobc mac cfg reg=0xE24
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: inbound rxstat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: inbound txstat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: io int stat reg=0x408
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: pcmcia cfg reg=0x1A0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: pcmcia stat reg=0x3C
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: bist go stat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: bist done stat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl debug reg 0=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl debug reg 1=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl debug reg 2=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: obl debug reg 0=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: obl debug reg 1=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: rxq debug reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: txq debug reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: gigmac cfg reg=0x1001
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: gigmac stat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-FATAL: An unrecoverable error has been detected. The system is being reset.
*Mar 24 22:12:30.695: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 24 22:12:30.695: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Mar 24 22:12:30.695: %OIR-6-CONSOLE: Changing console ownership to switch processor
*** System received a Cache Parity Exception ***
signal= 0x14, code= 0x84000000, context= 0x441ce024
PC = 0x4171295c, Cause = 0x820, Status Reg = 0x34018002
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
Autoboot: failed, BOOT string is empty
Autoboot executing command: "boot "

Hello Abubaker,
It crashed due to a parity error.
Imprecise Data Parity Error
Imprecise Data Parity Error
Which in other words means, a temporary error in memory. On single occurence adivice is to monitor the supervisor for re-occurence of such failure again. You can monitor it for 24 - 48 hours and if its a hard failure , the likelyhood of issue coming again is more and you need to replace supervisor. If it does not repeat you can consider this as a one time issue and contnue using it.
Hope this helps and please always rate useful posts.
Thanks,
Madhu

How do you troubleshoot Caching Errors in Java Runtime Environment?

I have run into Caching Errors while using JRE (versions 1.4.2 and 1.5.0, various updates) using Windows XP and IE6. The error screen has the title Error - Cache and appears when trying to download JAR files through a secure HTTP connection. The error reads: "Caching Error. Unable to store or update files in the cache." In the details box, the first line can differ:
java.net.SocketException: Connection reset
java.net.UnknownHostException: [followed by a URL]
java.net.ConnectException: Connection timed out: connect
I looked in the Java Control Panel to make sure that the "Enable caching" box is checked, and removed the proxy settings in IE. The user has sufficient rights on the computer to download files.
How does one go about troubleshooting these caching errors? Is there a reference document available? I could not find anything on the Sun site or anywhere else.
Any help would be very much appreciated.

I deleted c:\Documents and Settings\<user>\Application Data\Sun (the same as in Java Control Panel->Temporary Internet Files->Settings, but at higher level). After that and some machine reboots it worked.

XML parsing error: xml processing instruction not at start of external entity (error code 17)

I created a form and recieve the filled in form by email from participants. It has always worked in the past. Recently when importing data into the master form (from filled in forms in xml files sent by applicants) I am getting this error message..."xml processing instruction not at start of external entity (error code 17), line 2, column 1...." pointing to the file of data (xml) I am trying to input. If I pull up old data forms (from 2009) they work, but now I am getting this error. I run Adobe Design Premium CS3 for Windows. Can anyone tell me what to do to fix?

I created a form and recieve the filled in form by email from participants. It has always worked in the past. Recently when importing data into the master form (from filled in forms in xml files sent by applicants) I am getting this error message..."xml processing instruction not at start of external entity (error code 17), line 2, column 1...." pointing to the file of data (xml) I am trying to input. If I pull up old data forms (from 2009) they work, but now I am getting this error. I run Adobe Design Premium CS3 for Windows. Can anyone tell me what to do to fix?

Default Cache Error on a G4 Quicksilver

So I've got a G4 quicksilver and it will not boot.
I tried all the different ways to get it to boot. Holding "c" with a boot disk, checking the battery, unplugging ram one at a time, etc...
The problem is, when I hold "option" to get into the disk boot option screen, is sees the drives (Operating System Drive & a Boot CD). I select either one, and a which screen pops up and says: "Default Cache Error, type "mac-boot" to boot the computers or type "shut-down" to shut down the computer.
I've tried every combo and it does one of these things:
Locks up on black screen
White screen pops back up and crashes
Starts loading (apple logo on screen) then the circle slash (ø) pops up like there
Please help.

Ok, So I got the OEM install disks with the Aplle Hardware tester. Here are some pictures of the issues I had durring this:
Boot 1) In inserted the Hardware disk and got it to boot first time, here are those pictures:
It looks like I had a issue with the Logic board or somthing that was plugged into it. as seen here: http://meistergaugefaces.com/mac/mac_6.JPG
My hardware profile: http://meistergaugefaces.com/mac/mac_7. JPG
It got all the way though the Logic board and mass storage scan, but half way through the RAM the crashes started back up. Here are a few more pictures of those misc errors:
Booted off the hardware disk and got these 2 on the 2nd boot:
http://meistergaugefaces.com/mac/mac_8.JPG
http://meistergaugefaces.com/mac/mac_9.JPG
Another Default catch error on the second attemp of the 3rd boot:
http://meistergaugefaces.com/mac/mac_10.JPG
This crash happened durring the 3rd boot:
http://meistergaugefaces.com/mac/mac_11.JPG
Message was edited by: MEISTERGAUGEFACES

Proactive caching Error while installing BPC 7.0 SP6

All,
We are installing BPC 7.0 sp 6 on Microsoft SQL Server 2008 (RTM) - 10.0.1600.22 (Intel X86) Jul 9 2008 14:43:34 Copyright (c) 1988-2008 Microsoft Corporation Standard Edition on Windows NT 5.2 <X86> (Build 3790: Service Pack 2)
In short SQL 2008 Standard Edition. Will BPC 7.0 work with it?
We tried to install the BPC and recived the "Proactive caching" errors. I know we will need this feature for ROLAP.
Can we keep Standard Edition and make it work? Or we will need EE of SQL for BPC to work?
Thanks for your help.
Sam
Edited by: Sam Patel on Mar 24, 2010 10:05 AM

SQL Server EE is required for all SAP BPC Microsoft versions.
BPC is using functionalities from SSAS delivery just with EE.
Proactive caching is one the features available just into EE not into SE. But are also other features used by BPC from SSAS which can be found just into EE.
It is true that actually just for SSAS we require EE, for all other componetnts we don't really need EE.
So the installation will work, but of course you will have some limitations coming from Microsoft.
For example SQL Server SE is able to handle maximum 4 processors.
RS can not be installed into Web farm if you are using SE
And many others.
I hope this will help you to have a bteer view about what is reguired and why.
Regards
Sorin Radulescu
Edited by: Sorin Radulescu on Mar 25, 2010 2:39 PM

External Cache Error

Similar Messages

Maybe you are looking for