External display (via DVI) takes 10 minutes to turn on

Hi!
We have a 15" G4 Powerbook about 16 months old. We often use it with an external (non-Apple) LCD monitor, in dual mode, via DVI. For most of the time we've had the PB, there was no problem at all. However, in the past few months a puzzling problem has developed. When the monitor is plugged into the PB's DVI port, the PB will believe there are two monitors available but it will not send any signal to the external monitor at first. After about 10 minutes, it will suddenly start sending a signal to the external monitor and everything is fine. However, if the PB subsequently is allowed to go into sleep mode, upon resuming it again refuses to send a signal to the external monitor for about 10 minutes.
Any idea what is going on and how this might be fixed? It's really frustrating.
Thanks!
G4 AlPB 15" Mac OS X (10.3.3)

I think I have this problem as well, I keep using the PB with LCD projectors, again they are detected, but I can't get an output.
Not sure I get anything after ten minutes though, I'll leave it today to try it.

Similar Messages

Macbook can't detect external display via DVI cable

I just bought Samsung PX2370 monitor and attempt to connect it with my Macbook Aluminum (late 2008). I have mini display port to DVI adapter and DVI cable. When I hook up my Mac, nothing comes up. The screen on macbook goes blue briefly and then back to normal, but nothing has been detected. I've manually set the source of signal to DVI, and tried to use Detect Display but nothing happens. Even I try to detect the monitor by using Windows 7 (via bootcamp), the display remains idle.
I had tested the monitor using DSLR although by HDMI, it work.
Any help would be much appreciated.

Hey hparekh and welcome to the forum -
It looks like you have the correct hardware. You should check your connections... make sure your using the Mini DisplayPort and not the Ethernet port (common mistake) and all of the connections are plugged completely. Make all of your connections with your MacBook on and then turn your Dell on. You might need to go through your Dell's setup to make sure that it's recognizing a DVI input rather then HDMI.
Might be a bad DVI cable or a defective monitor or maybe a bad Mini DisplayPort to DVI adapter. Are they all new products?

MBPro won't detect external display on DVI

Hi Folks,
I have a strange problem that gives me quite some headache:
Is use a MacBook Pro 3,1 2.2 Ghz, 4GB RAM, 128MB NVidia something together with a Samsung SyncMaster 215TW.
For the past year I was using my external screen without any trouble, connecting it via DVI to the mac. Every night I turn down the lid putting the notebook in sleep mode and switch off the monitor. Exactly as I did yesterday. But this morning however the external display didn't wake up as usual it did just nothing - was not even detected via the detect display function. And this is still the case right now.
So when I plug (or unplug) the DVI to the external something is still going on. I get the blue screen (don't get that wrong that used to appear just before it would expand the desktop to the external screen, but then it switches back as if there would be nothing connected.
No relevant entries in any logfile. System Profiler shows "Status: No display connected". The display itself says some no connection message if unplugged and - get this - falls to sleep mode right after I plugin the dvi connector to the mac.
I tried all this:
-reboot (with display connected & without display connected and all other imaginable combinations) - no positive result
-the display via DVI-VGA adapter works (but the image is not as nice unfortunately)
-reset PRAM (boot with optioncommand+PR)
-reset the entire thing (no power, no battery and hold the powerkey for 10 secs.) nothing
-connect some other external display to the mac via DVI - works perfectly
-connect the display via DVI to an other macbook pro computer - works perfectly too
-hard reset the display via the (red) support menu - no result
-an other DVI cable - no result
-booted from the leopard install cd - same thing
-booted from an other harddisk with 10.4.10 (removing the internal disk)- same strange behaviour with the old system
-booted ubuntu linux 8.04 - even here the same problem X doesn't recognize the external display if it is attached to the DVI port also no entries to the logs here.
-SwitchResX and tried to reset the display setting from there (vendor id 4c2d & product id 213 & 214) but still no success.
- called the apple support and my distributer of trust - no ideas but could be a hardware fault (mmh ok... but why do all other display I tried work perfectly with that beast of macbook pro but not any SyncMaster 215TW?!? that worked great for the whole last year)
I guess the macbook had a very bad dream that very last night about mac eating foo-bars that crawl through DVI cables from any 215TW display.
As for now I have a date with the local apple service partner -- in three weeks (it's holiday time in g.o. germany). Don't know what to tell him: Probably I'll need to go there with the screen to show them the entire scenario. Hopefully they (still) think it's a problem with faulty apple hardware (or system software) and replace the logic board.
But I'm still in hope! Is there anybody out there having an idea with what I could try next to bring back the love between my macbook and the lovely 215TW display?
greetings,
brutus banane

I have recently bough a new Macbook Pro 15.4", it worked first time with a Samsung Syncmaster 2493HM but after a few days the 'detect display' utility ceased to connect, then a short while after on start up I was getting a blank screen with a flashing folder with '?' on it, preventing me from booting up successfully.
I tried the reset p-ram, didn't work then I tried an archive install of OSX and that ironed out all the creases - for a day, there has been no flashing folders on start up but the Samsung has failed to be detected and this morning wouldn't work no matter how many restarts or cable disconnecting attempts.
So I called Apple helpline, told the guy what had happened, he mentioned to try the install discs again with the display connected to see of the MBP sent a signal to it, after choosing the language in the OSX installer, the display was once again recognized! I didn't have to proceed any further with the install discs so quit, reset and ejected the install discs and all seems well again.
For how long i wonder?
I have no idea of this will work for anyone else but it works for me at the moment.
Interested to see when and how this finally gets solved!
T.
Message was edited by: Tyke Tyler
Message was edited by: Tyke Tyler

External display via Mini DisplayPort to DVI no longer works with MacBook.

I had not used my external monitor in the last several weeks. I believe there have been a few OSX Lion updates since the last time I used the external monitor. I had installed all the updates prior to connecting my external monitor again. However, a few days ago I tried to connect the external monitor and all I get is a "No Signal" message on my external monitor. The Mini DisplayPort to HDMI works on my LCD TV, so I know the MDP works. I have also replaced the MDP-to-DVI cord and the external display still doesn't work.
I connected the external monitor to another computer running Snow Leopard and the external monitor works. So, the external monitor does work.
I have seen a few posts aboout this, but nobody seems to have a solution that works or is directly on point to my issue. I have tried to use all the scenarios for plugging in the external monitor and external monitor power. I tried to reboot the laptop with and withoout the external monitor connected. Same thing with the exteernal monitor plugged in and no power, etc. Nothing works. I have tried to repeatedly turn the external monitor on and off while connected to the MacBook. Again, that doesn't work.
So, I am open to any help someone may have. Here is what I am running:
MacBook, Aluminum 13" Late 2008
OSX 10.7.3
NVIDIA GeForce 9400M

While we all have MacBooks in this forum most of us don’t run Lion. There's a Lion Support Community where everybody has Lion. You should also post this question there to increase your chances of getting an answer. Lion seems to have problems with external monitors. https://discussions.apple.com/community/mac_os/mac_os_x_v10.7_lion

External Display via S-Video

So, I just plugged my laptop into my TV via S-Video.
Nothing happened... I've tried the Monitor Settings in the Gnome control panel... Still nothing...
I'm supposing I need some sort of Driver... (I have an Intel Gfx Card).
Please Help...
Oh, and... this is what happens when I run "Xrandr"...
Screen 0: minimum 320 x 200, current 1280 x 800, maximum 4096 x 4096
LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm
1280x800 59.9*+
1024x768 60.0
800x600 60.3 56.2
640x480 59.9
VGA1 disconnected (normal left inverted right x axis y axis)
TV1 disconnected (normal left inverted right x axis y axis)
Last edited by oldtimeyjunk (2011-10-25 15:34:24)

Casting another vote.
I too am experiencing B&W, low resolution, shaky output on an external display when using a DVI to video adapter. DVI to VGA works like it did before, Snow Leopard upgrade, for external monitors. I would hope that DVI to Video would work like it did before upgrading the OS.
The solution refers to totally black screens when hooking up an external monitor, not the display being B&W however, restarting does solve the issue.
I always put the computer to sleep, attach video cable to DVI port, wake the computer and have had no problems.
Please patch this issue.

Why does the Retina Screen on MBPR2013 make a Weird Flash when I have a External Display via HDMI hooked up?

I just bought a new 2013 early MACBOOK PRO RETINA. When i have an external Display hooked up via the HDMI port, I noitce when I wake the computer UP it has a Different type OF QUICK FLASH that comes up than when there is nothing hooked up so I don't know if that makes sense to anyone, but its very disturbing to me, it makes me wonder if there is something wrong with the HDMI PORT ????? Has anyone else experienced this or knows if this is NORMAL behavior of the new RETINA displays or the HDMI port makes it FLASH weird upon WAKE UP??? I have unplugged the HDMI and when I do the SCREEN comes up normally it just blinks on. But when HDMI is used its light lightening stike. Don't know how else to explain it, maybe i need to do a video and Post a video.

One more disturbing thing. When the screen on my MBP goes black and I check the system preferences for "Displays", the MacBook Pro display is not presented as an existing display. Only the still-functioning Apple 20" Cinema Display.
Where did it go??

Second Apple Display via DVI

I'm sure this must have been covered before so apologies if I'm going over old ground, but can't seem to find exactly the right answer to my question, so if anyone can help or point me in the right 'post direction'.....
I have a MacPro 4.1 with a Mini DisplayPort output plus a DVI output. I've been running a 24" Apple Display (via the MDP) and a standard monitor (via the DVI) quite happily.
Now want to upgrade to a second 24" Apple Display, but obviously can't connect to the DVI output due to the hardwired MDP from the monitor. Assumed that I could buy an adaptor (male DVI to female MDP) but can't seem to find anything......
There must be a way around this issue....?
Thanks

Click here for a converter.
(53174)

My external display via VGA only works when macbook air is shut?

I'm using a MDP to VGA to connect my 2012 Macbook Air to an external display. When the Air is open I can view only the desktop (no open apps). The open apps only appear on the external monitor when I close the Air (after a couple of seconds)!! Have I accidently altered some settings somewhere??? Makes no sense to me.

Update - I ended up spending about an hour on the phone with a very helpful rep from AppleCare. He was also stumped by this problem. We ended up solving it by using a remote screen-share app that allowed him to see what my video card was sending to the external display, and he directed me over the phone to change the settings (quite funny really - it was literally "move your mouse up a tiny bit, now click, now left, etc).
So, my problem is solved for now, albeit in a very cumbersome way. Still amazed that there's no way to fix this properly.

Lenovo U410 takes 10 minutes to turn on - Please help

Background:
Got the laptop - 500GB HDD and 24GB mSATA SSD with iRST/ExpressCache. iRST was by default enabled in BIOS.
Upgraded to 8.1 a few days after its release. Everything ran fine for a while.
And one day after opening up the laptop and waking it from sleep I got a message saying "It appears Intel Rapid Start Technology is not enabled on your system." Since then the laptop takes 10 minutes to start where as before when I got the new machine it took 20 seconds.
I did a system recovery using OneKey but that apparently only restores the C:\ drive so the mSATA (D is still having issues that are causing the long boot time.
I tried a few things like deleting the mSATA volume/recreating and that did not help. iRST since the error message in the BIOS is showing as INVALID. I can't use diskpart to clean because the mSATA does not show when doing a list disk. I've changed AHCI to RAID and I can't get Windows to launch or go into the troubleshooting command prompt because Windows has an error when trying to start up and it will just boot loop.
At the moment if I power my machine on from a powered down state it will start on a black screen that will sit there for 5-8 minutes and then the Lenovo screen with the loading circle will take another 2-3 and finally when Windows launches the system will be slow for another 2-3 minutes before I can even open the Task Manager. If I try to restart when Windows is loadaed it will just stay at a black screen until I hard-shut down using the Power button.
I really don't know what I can do without voiding warranty (I thought about taking the mSATA SSD out but don't want to void the warranty). I really don't know what could have caused this (maybe upgrading to Win8.1?) but it's been happening since I woke the computer up from sleep once. I've heard that Lenovo Energy Management might be a cause of the iRST issue too?
I'd also like to note that I tried uninstalling iRST and the uninstall was OK. Upon trying to reinstall it iRST is saying that my system does not meet the requirements which obviously is incorrect.
Can someone or support please provide some help? Is there a way I can image my system (both HDD and SSD) to factory?
Thank you.

I've also tried reinstalling ExpressCache but to no avail - it says during the install a suitable drive was not found.
Doing a eccmd.exe -info says a SSD is not mounted.

Using external Display via Mini-DVI to VGA Adapter does'nt work

Hey Guys,
i recently bought a mini-dvi-to-vga adapter.
When I plug it into my macbook and connect it to my 19" external TFT, the MB recognizes the TFT as [Medion] MD30219PH but the display stays blank (no matter if i choose mirroring mode or extended desktop)...
Already changed the Hz-Rate between 59.9, 60 and 75 Hertz and the Resolution also... but nothing happens.
In extended Desktop mode i can even slide the cursor into the area where the display is supposed to be...
Hope u can help me
thx

From what I've been told, using the computer's video output isn't outputting a true NTSC picture. I was told when talking about how the Macbook Pros dropped the S-vdieo port that I shouldn't use that anyways, but rather to go the firewire route. THat was actually converts the video source to true NTSC instead of taking a computer output to a TV. While I have no doubt that it works, I'm willing to bet that you'll see a noticeable difference between the G5 S-video and your MB using firewire. Most consumer camcorders from the past several years do digital (firewire) to analogue (NTSC) conversion, so you probably don't even need a new box.
-Brian

Mbp 15 external display via mini display to hdmi flicker

wondering why my mbp 15 to samsung 22" led monitor via minidisplay to hdmi give me flickers, whereas if i connected to my samsung 37" lcd tv no flicker at all. right now i had to connect to my monitor using minidisplay to vga to avoid the flicker.

While we all have MacBooks in this forum most of us don’t run Lion. There's a Lion Support Community where everybody has Lion. You should also post this question there to increase your chances of getting an answer. Lion seems to have problems with external monitors. https://discussions.apple.com/community/mac_os/mac_os_x_v10.7_lion

It takes several minutes to turn on my computer, and everytime I try to use Microsoft Word, it freezes. Is this a memory problem? RAM?

I am usure as to why it is taking up to 10 minutes for my computure to fully load. I recently deleted a lot of old documents and pictures trying to free up space, but this did not solve anything. Also, everytime I use microsoft word my computer will type ok for a while and then freeze out of no where. I read on another post that this may have to do with RAM space. I am not quite sure what RAM is though... I also re-installed Microsoft 2008, but I am still having problems. What might I do?

Hi
I would download the free Onyx application (Google will find it) and go through its sequence of maintenance operations: Verify, Maintenance, and Cleaning.
When its finished all these steps, I'd then reset the SMC and PRAM:
- Reset the PRAM: http://support.apple.com/kb/HT1379
- Reset the SMC: http://support.apple.com/kb/HT3964
If you still have problems after these steps come back to us
Bob

Internal/External displays blank when external connected while sleeping

When I connect my external display to my MBP (late 2011) while it's sleeping, the MBP awakens but both the internal & external display are blank.
The MBP is running ML and is connected to external display via DVI. No response to external Logitech keyboard or internal keyboard. Currently my only recourse is to ssh in from a co-located Vista machine & 'sudo reboot'.
If MBP has recently been used (say < 5 min or so), everything's fine -- external display fires up & external KBD/Mouse work.
I'd be interested in any way to prevent this problem if I forget to open MBP for a moment before connecting Power/DVI/USB. Alternately, a command
I could issue via SSH to reinitialize display would be great.
Thanks. Kent

Pleased ignore this thread - managed to double post somehow ....? Sorry
Chris

External display flashes and shows 'snow'. (Video of behaviour included)

Since yesterday, my Macbook Pro is acting strange. When I connect it to an external monitor, it usually works. Everything goes well for 10 to 30 minutes, and at some point the display starts tearing, showing snow, and flashing. These flashes get worse and worse, up till the point where I have to reboot. Rebooting seems to help a little. Whenever the laptop hasn't been used for a few minutes it works correctly again, for a short while. (This makes me conclude it's some sort of heat-related issue)
The issue is present on multiple monitors using different DVI cables. I only have one mini-displayport to dvi adapter, so the problem could be there too.
This problem does not affect the internal display of the macbook in any way.
Here is a short video showing the behaviour:
http://www.youtube.com/watch?v=4BotUqHb3dM
What should I do? Try to figure out wether it's the mbp or the connector or just bring it in for a repair. (It's less than a year old)

I have had similar issues with my 15" MBP. Occasionally my external monitor will go 1980s and display what looks like crappy tv reception.
Also, connecting or disconnecting an external display (via the single link mini display port to dvi adapter) has a tendency to lock up the entire machine (both displays black, won't respond to keyboard or mouse) until the power is cycled.
Also, my built in monitor has a habit of flickering/glitching lines.
These problems seem to happen regardless of which graphics card is active.

Ongoing fatal crash and security bug related to connecting external display

The infrastructures in OS X to resume from sleep, to authenticate, and to change displays is fundamentally not working.
The security bug I have encountered has to do with connecting a cinema display exclusively to a MacBook Pro. This is a specific situation, but please note that I have experienced the same problem on no fewer than three independent laptop. Plus, the Genius in the Apple Retail Store was convinced of the general instability of this infrastructure. The security problem is that hot corners no longer function if I transition between two states in the same reboot. The first state is where I have the laptop powered on and using its own internal display exclusively (when I'm on the road). The second state is when I have the laptop displaying its output exclusively on an external display (when I'm at home). What happens is that an attempt to use hot corners fails. There is no response. I even added configuration on all four corners (whereas I originally had settings only for the rightmost corners), and even then, the hot corner action (of sleeping the display or entering locked screen saver mode) does not commence. This prevents the user from being able to secure the display on demand using standard methods that are supposed to work.
The instability level related to connecting the external display exclusively is high. Again, I've experienced this on no fewer than three independent laptops, and the Apple Genius at the Retail Store confirmed that this aspect of OS X did not work consistently. When I want to connect the cinema display to the laptop in such a way that the laptop's own display is not part of the active screen, the process I use succeeds about half the time. Supposing I have been on the road, where I am using the laptop display exclusively. I then put the laptop to sleep. When I return home with the lid open, I connect first the USB (power) from the cinema display to the laptop, and then I connect the Mini DisplayPort. When that step works, what happens is that the login screen shows on the cinema display despite the fact that my laptop lid is closed. This is good, and is what I want. At that point, I open the laptop lid and quickly log in.
With Apple being a mobile device company, I rely on the laptop for tasks that one traditionally may use a desktop for. This simply points to the versatility of the laptop. But I'd like the bugs resolved, so that I do not have to hesitate to make use of the inherent flexibility possible with the MacBook Pro.
Here's what happens when the process (of connecting the external display in a way that establishes itself as the only screen in use by OS X) fails. Firstly, when I connect the external display via Mini DisplayPort, the laptop doesn't even respond. Instead, it remains asleep. So to work around it I have to repeatedly disconnect and reconnect the Mini DisplayPort so that the asleep MacBook Pro will see that there is a display connected to it. Also, sometimes that isn't even enough and I have to open the laptop lid, and put it to sleep again so as to trigger whatever actions are necessary to recognise the external display (presumably by having the laptop recently awake). Around half the time, I have to play this game of disconnecting and reconnecting until it actually works. This high level of reproducibility (confirmed by the Apple Genius representative's confidence that this part of the system doesn't actually work) should make it easy for an engineer to look into the problem.
Fatally, and recently, OS X has completely crashed when I have attempted to connect the external display. The external display has gone completely blue, and after a half a minute, it blanked out and my entire laptop became unresponsive. I called Apple Support and was given a case number. I also took the laptop into the retail store to see if I could recover my current session without rebooting. There was no process suggested to make that happen and I was told to reboot the machine. I've had this happen before on other laptops, and it is frustrating that the kernel reaches such a state that it cannot be used. As I see it, this problem is not too unrelated to the way that I need to play a game in order to get the external display connected exclusively. Here are some workarounds that could be added:
Firstly, whenever I connect an external display, I'd like the laptop to see that this has happened, and to take action accordingly (such as resuming from sleep). Secondly, If I connect an external keyboard, and press a key on it, I'd like this to wake the laptop too (in the event that the first method fails for some unforeseen reason). I'd also like the connection of the cinema display's USB power not to cause the laptop to enter into a confused state between asleep and awake. Sometimes I need to disconnect and reconnect USB power in order to trigger the laptop into waking, but that's only because it's not doing it on its own properly. On the other hand, I also ensure that the laptop doesn't have the Mini DisplayPort connected without also having the cinema display USB power connected, because that also is an unsupported configuration.
I've also gotten the laptop to become confused about whether it is asleep or awake. When I open the lid, it seems to enter into sleep mode, but closing it seems to bring it into an active state.
Also, I've successfully logged on and authenticated with the screen showing exclusively on the external display. But just ten seconds after I start using the system, the laptop falls asleep--with the lid open! Whatever triggers that action doesn't seem to be on track. The laptop is open, there are incoming events such as mouse movements and key presses, and the external display is on and is in use. And then the laptop falls asleep! This has happened numerous times. Not only should this not happen; the instances where it does happen can cause further instability and put my system at risk of fatally crashing.
Also, the authentication system itself is highly buggy--far more than it should be. At times I have opened the laptop lid and caught a glimpse of a window before I have begun the login process. Also, an external authentication application that asks for Kerberos/AFS login credentials has been able to overlay itself on top of the primary authentication (whereas I should only see a single login dialog when I need to authenticate to the system). Also, I've had several of these authentication screens overlay on top of one another, although it's been months since I've experienced that one (so it may have been fixed). Also, around a third of the time, the window that authenticates me (on the black background) somehow transfers itself into the background (even though there's only one window!). What that means is what I begin to type my password, and now the laptop starts beeping at me and I need to manually click on the password field and begin entering my password again. This really shouldn't happen, and indicates too much complexity in this authentication process (such as, more OS X code is involved than is strictly necessary, which is likely to make the authentication system more difficult to test). Also, at times, I have been using too much CPU, such that the authentication screen takes too long to emerge. That also means that I'm not able to logon until I uncleanly shutdown the laptop. If the laptop has been asleep, and is revived in preparation for login, then that login screen should be given highest priority, even if there are other heavy CPU or I/O intensive tasks running in the background. And maybe the login dialog shouldn't disappear when the user is legitimately attempting to log in. So even if there is a possibility that the system is under heavy resource use (or there is a stall or minor deadlock), it shouldn't prevent the user from logging in altogether.
At the moment, the very fact that the system shut down uncleanly means that the full disk encryption suite that I used has entered into an undetermined state, suggesting I may lose access to all my data. It's my hope that I can rely on Apple's products to interoperate in a way that won't cause me to be fearful and restrictive in my use, so that I can freely connect an external display at times, and at other times carry the laptop on the road.

Ive got the same problem with Samsung UE225010 monitor too, its full hd but it looks terrible, could it be Displayport adapter issue, because couple month ago Ive tryed with some IPS display, and it looked same bad.

External display (via DVI) takes 10 minutes to turn on

Similar Messages

Maybe you are looking for