External hard drive won't connect

I have been using an external drive to transport material from an old computer to the Macbook Pro. Normally I have used the firewire 400 port on both ends of the journey. Suddenly, the MacBook will not connect to the hard drive. I meticulously power the hard drive off before ever plugging anything in or removing a cable--it is always fully connected before power is applied, old habit from years of firewire problems. First I tried the firewire 400 port where it normally works. Nothing. Restart the computer. Firewire 800 port, finally USB port. None of them see the hard drive. I took it back to the original computer, an old G4 with USB 1.1, so I use Firewire 400 there. Works fine. Disk Utility verifies. Back at the MacBook, It now will start for a little while, maybe 30 seconds, then it powers off by itself. I've changed cables and power supplies. Same symptoms no matter what port to the Mac Book. But it still works on the G4. Other external drives on the MacBook continue to work. Essentially I need to do my nightly work of exporting Quicktime movies made on the G4, into a different format and save that onto the other external drive. So I'm going to lose an entire night's work because the drive and the MacBook, suddenly, unexplained, won't play together. Any ideas what is going on?

Absent the source drive, I used overnight to make a large file transfer between two existing drives--should have taken a couple of hours. The progress bar shows it is tantalizingly close to finishing (so I don't want to abort and reset) and it seems to be making progress, but sooooo slowly. I did a small file transfer the opposite direction between those two drives, a 50 Mb file that should have taken less than a minute. Instead I could watch the progress advance, but it took closer to 10 minutes. Aside from Safari now, there is absolutely nothing else happening on the computer. With the earlier problems, it was a fresh boot up. What is going on?

Similar Messages

I just installed OS X Yosemite and now my WD My Book Live external hard drive won't re-connect. My Safari keeps kicking out and giving me error message after error message and my computer is really slow. How do I resolve? Can I uninstall this ?

I just installed OS X Yosemite and now my WD My Book Live external hard drive won't re-connect. My Safari keeps kicking out and giving me error message after error message and my computer is really slow. How do I resolve? Can I uninstall this ? I had to re-connect my iMovie t

USB2.0 PCI cards that use the NEC chipset seem to give the least amount of problems for Mac users.
OWC have a few different ones for sale.
http://eshop.macsales.com/Search/Search.cfm?Ntk=Primary&Ns=P_Popularity%7c1&Ne=5 000&N=7057&Ntt=USB2**0**cards
Do you also connect the external USB drive to the AC power as well while you use it ?
Sometimes USB external drive problems are resolved simply by plugging them into the mains power and trying again.
Stewie
Message was edited by: stewiesno1

ITunes library stored on an external hard drive which is connected to my airport extreme, I wish to share my iTunes library over my network, I can do this with my laptop, but not with my iPad, can anyone tell me if it is possible

I have my iTunes library stored on an external hard drive which is connected to my airport extreme, I wish to share my iTunes library over my network, I can do this with my laptop, but not with my iPad, can anyone tell me if it is possible

You can't connect directly to the external drive, but should be able to use iTunes Home Sharing via the laptop.
http://support.apple.com/kb/PH1453

HT1151 I have my iTunes library on an external hard drive that was connected to a PC, now I want to connect to my new iMac and load the iTunes library onto that computer, can I do that?

I have my iTunes library on an external hard drive that was connected to a PC, now I would like to connect that hard drive my new iMac and load the iTunes library onto that computer, can I do that? Looking for a solution that keeps me from re-ripping my CD collection.

Here are the official Apple Support instructions:
http://support.apple.com/kb/HT4527
Ciao.

External Hard Drive Won't Mount- Need to recover files

Hello Everyone,
I am hoping that one of you fine mac experts may be able to assist ~
Problem: External Seagate FreeAgent Desktop USB external hard drive
won't mount on desktop=ie: no access to my important files.. Please Help!
Details:
External seagate freeagent 500 GB Desktop USB HD ( only 2 months old)
(using for document / file backup-not as a startup disc)
on my Mac G3 350 MZ Blue & White Tower /768 ram/ running OSX 10.1.5 & OS9.2~
~
Problem: Started using the external 500 GB HD 2 months ago -with no problems-until this morning. Tried to double click to open it to access files
and got the "beach ball of death" and needed to restart.
My trusty G3 started up fine, however, the external HD was now
not showing up on the desktop as normal. I troubleshooted -by restarting,
trying different a/c plugs/ different USB ports , ran disk utility..called
seagate -not much help . Seagate said to try the HD on another mac-which I did-
a G5 tower- same problem.
~
The External hard drive will show up in disk utility, but is grayed out.
and when click "mount" same two messages keep showing:
message 1: "a disk attempting to mount as unknown has failed verification or has failed to
mount.please use disk utility to check the disk"
~
message 2- when unplugging and repluggin the usb in-and upon
restart:" you have inserted a disk containg no volumes that mac osx
can read to use unreadable volumes,click initialize to continue with the disk inserted ,click continue"
~
( I really need access to these files- and do not want to re-initialize the HD!!)
I ran Disk Utility /first aid "verify & repair , the following info came up:
Repairing disk "main backup 2007 ".
Checking HFS Plus volume.
Checking Extents Overflow file.
Checking Catalog file.
Invalid key length ( <<<IN RED )
Repair completed. "
~~
Though it said the repair was completed, the "invalid key length" issue
still comes up when re-running disk utility...Hard drive would still not
mount on desktop-even after restarting .
~~~~~
If there is a mac genius out there that can help?- it would be greatly
appreciated. I have tried to call seagate several times in the last several hours-
1st time-they disconnected me after being on hold 10 minutes-2nd call
I was put on hold for 40 minutes ..Finally spoke to someone ( they are not mac users or mac experts!)and he said I would need to send it to Seagate's Data Recovery-... for a fee of course!
~~~
At this point, I am hoping to just get the files and photos off
the hard drive- I heard about Disk Warrior-should I use that and if so
what version?
Thank you very much!
L

Will zapping the PRAM be of any use in getting the external to mount on the desktop?
Your external Hard drive is already recognized. But it cannot be mounted on the desktop due to its directory damage. You can certainly Zap the PRAM, and it will not hurt anything, but I am skeptical that it will change the situation.
Do you think the Disk Warrior 4.0 cd will even work on my G3 350MHZ running Mac OS 10.1.5?
If you boot from the CD and run it from the CD, absolutely yes. If you attempt to INSTALL it from a download or a CD, probably not.
Have you ever used Disc Warrior and is using it complicated?
I own and use Disk Warrior. You select the drive to be rebuilt, it builds a proposed new directory from the information and file fragments available.
When complete, it will provide a list of problems encountered, tell you what files have been placed in the "Rescued Items" folder, and allow you too look at your drive using the proposed new directory. Your only decision is whether the new directory seems to be an improvement over the old \[in your case, hopelessly corrupted] directory. You then tell it whether to replace the old directory with the proposed new directory, or to abandon its work and leave your Hard Drive unchanged.
Is there a good chance that the ext HD will still have my files on it- or do you think from what I've described that they are gone ?
From what you have described, your files are very likely to still be there. Sometimes in a situation like this, a handful of files cannot be recovered.
My other thought was to take the external HD there and have them try to recover the files.
Make sure you completely understand the costs involved. File recovery using a service like DriveSavers can run into many hundreds of dollars. They are prepared to disassemble your drive in a clean room and replace controller boards and read/write heads to achieve success. Your drive has serious, but not fatal, Directory damage. The Hardware, and most of your files, are likely just fine.

External hard drive won't mount, even after disk repair.

My Toshiba external hard drive won't mount on my MacBook Pro 10.8.5. I can see it in my disk repair, and when I repair, "the partition map appears to be ok." But I can't access the icon to be able to open the hard drive contents on my desktop. Help!

Hello maccynicwhoalwayshasmacs,
Thanks for the question. After reviewing your post, it sounds like trouble with an external HD mounting. I would recommend that you read this article, it may be able to help you resolve or isolate the issue.
USB and FireWire Quick Assist
Thanks for using Apple Support Communities.
Have a nice day,
Mario

After installing snow leopard my external hard drive won't show up on screen or backup

Afer installing leopard my external hard drive won't show up on my desk top. It also won't backup my hard drive with time machine. I need help.

Try going to finder preferences, general, make sure show these items on desktop external disks is clicked. You can also go to sidebar (same pane) and click it there so it will show when you open your HD. Time Machine>system preferences>time machine>turn it off click select disk, make sure the correct disk is selected, the turn TM back on. Hope this helps.

External hard drive won't shut down after switch from OS10.5 to OS10.4.11

i recently chanded my OS from 10.5 to 10.4.11 (as a programme i want to use is not compatible with leopard), but since i have done this my external hard-drive won't shut down automatically when i shut down my mac. i have to switch it off at the plug instead.
can anyone suggest how i can get it to do this again?
i'm a little concerned that i'm damaging the external drive by turning it off manually all the time..
thanks

Some hard drives shut off with shutdown, some don't. Sometimes hard drives that did shut off with one system will not do the same with a different system. My hard drives which did shut off, prior to 10.5 now stay on.
This is not really a problem as all hard drives spin down after 10- 20 minutes when not in use, whether your computer is on or off. Leaving the drive on is fine, shutting it off manually is fine.
-mj
[email protected]

External hard drive won't unmount for disk utility.

Im not sure if this is the right topic area but I have a white macbook and my external hard drive won't unmount. I want to erase it via disk utility but it keeps telling me other programs are using it.

Drive Preparation
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.

My external hard drive won't show up on my macbook air, and my iPhone when connected won't show up as connected in iTunes, help

When I connect my external hard drive to my MB Air it is to recognizing it. It did 2 days ago and it is compatible I have been using it for a month now. Also when I connect my iPhone 6 to it, it won't show up in iTunes anymore......please help

Check that the data cable is securely inserted at both ends.
Try a different cable.
If you're connecting the drive through a hub, connect it directly to a built-in port on the Mac.
If you're connecting it directly, try a different port.
Disconnect all other devices on the bus, or as many as possible.
Test the drive with another Mac. Test another drive with this Mac.
If the drive is bus-powered, but has an AC adapter, connect the adapter.
Boot into Recovery and launch Disk Utility. Is the drive recognized?
If the drive doesn't work under any of the above conditions, and if another drive does work with the same Mac, then the drive has failed. You may be able to salvage the mechanism by removing it from the enclosure and installing it in another one, or in a drive dock.

My external hard drive won't show up on my MacBook Pro

So, I'm trying to transfer my music from my PC to my MacBook Pro. I put all my music on an external hard drive, but for some reason when I plug it into my MacBook it won't show up on the desk top. I've already changed my preferences in Finder so that hard drives and disks will show on the desktop, but still nothing. I looked in utilities to see if the hard drive was there, and still nothing. The hard drive is a Toshiba and is fairly new, the light goes on when I plug it into my laptop, so I'm very confused. Can anyone help me with my predicament?

Check that the data cable is securely inserted at both ends.
Try a different cable.
If you're connecting the drive through a hub, connect it directly to a built-in port on the Mac.
If you're connecting it directly, try a different port.
Disconnect all other devices on the bus, or as many as possible.
Test the drive with another Mac. Test another drive with this Mac.
If the drive is bus-powered, but has an AC adapter, connect the adapter.
Boot into Recovery and launch Disk Utility. Is the drive recognized?
If the drive doesn't work under any of the above conditions, and if another drive does work with the same Mac, then the drive has failed. You may be able to salvage the mechanism by removing it from the enclosure and installing it in another one, or in a drive dock.

External Hard Drive won't mount on desktop!

Hey, guys.
I ran into a problem this morning that I've never ran into before and I wasn't sure where to write it but I thought this is best.
Here it goes...
Last night I had a power surge and when I restarted my computer, my external hard drive did not mount on my desktop. I than proceeded with restarting my computer, I relinked all my connections and I cant seem to get it fixed. I have a lot of material on my external drive that I dont have backed up (I know, a stupid move) anyways, I dont want to lose that information. Also, when I open up disk utility, the icon for my external drive is there and the partition I made for my external drive shows up also but the title of my partition for my external hard drive is not in bolded font. I tried to click the button to mount my external drive cause the specs tell me that it is not mounted but when I press the mount button, it does nothing. I than tried clicking the unmount button and than restart my computer and still nothing.
What problem am I facing and how can it be fixed?
Thanks.

Dear Jason,
Gary's advised is, IMHO, a very sound one.
The only thing I can think of about your problem, given the information you have provided us, is to run Disk Warrior on your external HD.
In fact, DW is particularly indicated in events, like:
"...you should run DiskWarrior when you suspect that there is directory damage on one of your disks. Directory damage can result in the disk not mounting (not appearing on the desktop when the computer is started), missing files or folders, an inability to move or copy files, or crashes when files are used...".
You could actually buy your copy of DW Licence on-line and download it directly onto your internal HD, starting from this "Information you must read before you make your purchase" page. A hardware copy of the software you have so purchased, will follow by postal service (or currier, if so you choose), shortly.
Follow all the instructions you will find in the download to install the DW software onto your main internal HD and then run it on your external hard drive.
DW has saved my data several times and in similar situations as you are experiencing. IMHO, you should seriously give it a try and, even in the unfortunate event it does not manage to solve your problem, it is one of those Mac OSX utilities which ANY Mac power user MUST have handy at all times.
So, no matter what, my opinion is that it is always well-spent-money those used to purchase your copy of DW: in the long run, you won't regret it.
In the event that even DW is unable to retrive your precious data, my suggestion is to contact Micro Com data recovery. It's going to cost you some money, but if you make a leaving out of the data you've lost on your external hard drive, it's going to be worth it.
All the best.
Costa

My external Hard Drive won't transfer files to Mac HD and causes Finder to crash

My external Hard Drive (Western Digital 2TB hard drive in a ICYBOX 2-bay USB 2.0 HD Dock) won't transfer files to the Mac HD. The transfer box comes up but stays at the 'estimating time' stage and remains like that. No matter how big the file/group of files are (biggest I've tried was only 500-odd MB) it won't transfer and stays at the 'estimating time' stage. When I try and stop the transfer, the transfer box remains at the 'stopping' stage until I restart the iMac. I can access other programs during this 'stopping' stage, as long as it doesn't involve the External HD.
When I attempt to open files from the External HD in Photoshop CS4, both Photoshop and Finder stop responding and have I have to 'Force Quit'. However, upon force quitting finder, I loose all icons on the desktop until I restart the Mac via holding down the 'Power' button on the back.
Ive looked at a few forums already and done a couple things they suggested to similar topics.
- I excluded the Ext HD on the Spotlight>Privacy tab.
- I verified the Ext HD via System Utilities. Some errors came up but the Repair was successful and subsequent Verifications have returned as 'OK'.
- I tried the Mac Diagnostic tool as suggested by Apple, but when I press the 'D' key on start up nothing happens.
The annoying thing is that this problem came out of the blue, the Ext HD was working fine 3 days ago.
My system:
iMac 21.5inch, mid 2010
3.6GHz Intel Core i5
8GB 1333 MHz DDR3
OS X 10.9.5 (13F34)
The Ext HD:
Western Digital 2TB
Mac OS Extended (Journalised)
1.91TB available on the HD
Shares a 2 Bay ICYBOX dock with another 2TB WD HD
Connected to the iMac via USB 2.0 to a 4-port USB 2.0 hub
Any help suggestions would be greatly appreciated.
Cheers,
Tom

WD EHDs have an extremely high failure rate so don't be shocked if it is failing. However what you can do first is reset the SMC and PRAM first on the computer, do the SMC reset 2-3 times, sometimes the first try does not work. If this does not work then using another computer move the files to another EHD, this time buy a high quality HD, something like one of these

External Hard Drive Won't Mount in 10.2.8

Greetings,
I have a MacBook Pro running the latest version of Tiger. I have a Maxtor 300 GB external hard drive (Mac OS Extended [journaled] ) which I use with my MacBook to store music, video, other media, and backups. I connect that drive to my MacBook via FireWire, normally, but the drive can also do USB.
Since wireless connectivity is so nice, I thought it would be nice to be able to access that hard drive from anywhere in my apartment, without being tethered to the drive by a FireWire cable.
Enter my wife's iBook G3 and Mac OS 10.2.8.
She has this computer from her school where she teaches. It has a G3 processor running at 600 mhz with 128 mb of ram. Since she rarely uses the old machine, I wanted to use it to "serve" my external hard drive to my MacBook.
But when I connect the hard drive to the iBook via either USB or FireWire, it does not mount. I ran Disk Utility and the drive is visible in the pane on the left of the interface, but when I verify the disk I get lots of error messages that say, "Reserved fields in the catalog record have incorrect data."
I don't want to let the iBook repair the disk because I am afraid it my screw the whole thing up and I would lose all my data...not a good proposition.
So, my question: What is going on here? Is this drive simply not going to work with 10.2.8?
I wish I could upgrade the machine to Tiger, but it does not have the minimum system requirements!
Thank you very much for your help. I apologize if I missed something else in the forums that addressed this same issue.
Macbook Pro 2.0 Ghz Intel Core Duo 1 GB Ram 15.4" LCD Mac OS X (10.4.7)

All you need to upgrade the iBook for Tiger is another 128 MBs of RAM. It has both Firewire and USB ports. You do want to upgrade it for what you plan to do. The problem you may continue to have, however, may be due to the fact that the age of the computer is such the disk controller does not support hard drive volumes larger than 128 GBs, which is probably the reason the drive won't mount.
The reason you get DU errors is likely because the drive was formatted using the Intel Tiger version of DU, while you were using the Jaguar version. That's a definite no-no.

New external hard drive won't show up in disk utilities...

I have a 2010 macbook pro 13" and just bought a 1tb toshiba canvio external hard drive.
The hard drive itself has a USB 3.0 hub running out of it and the specifications say that it needs to run into at least a 2.0 hub, which I have.
I know I will need to reformat the external drive to get it to work on a mac, but it won't show up at all when I plug it in... the drive starts spinning but there is no recognition by my mac.
Does anyone know what this is and how to fix it?

So far all MacBook users have been able to use this drive as a USB 2.0 by using a USB 2.0 cable with a micro usb connector (same as smartphones, Kindle, Nook) on one end. Connect the micro connector to the opening on the left side of the USB 3.0 connector on the Canvio - if you look closely you'll see that side is exactly like the USB 2.0 micro receptacle. That's all you need to connect as a USB 2.0 - the other connections are for USB 3.0 which no Apple system has yet (Dec 2011). Connect the other end (a standard USB type A plug) to your MacBook and it will work. If you want to use it for Time Machine, you'll have to reformat it. None of the supplied software will work with Mac You can read more at this thread:
https://discussions.apple.com/thread/3510032?start=0&tstart=0

External hard drive won't connect

Similar Messages

Maybe you are looking for