External HD connected to Airport Extreme only seen by one network computer

I've connected a MyBook external HD ("HD") to an Airport Extreme base station and configured it using Airport Utility ("AU") from my new MacBook Pro ("Pro"). The Pro sees the HD but my other two networked computers do not. I've run AU on one of the other computers to again configure the HD and the result is that again only the Pro can see the HD.
Other networked computers are an Intel iMac (Core Duo) and Intel MacBook (Core Duo).
  Mac OS X (10.4.10)  

Yes, this is as you indicated earlier and all of these settings are so designated. I have been to the Apple Store and the Genius enabled one of the two computers (I did not bring the other to the store). This was done by (1) repairing disk permissions and (2) installing a clean copy of Airport Disk Utility onto the computer directly from CD. Unfortunately, these two steps did not work on the computer that I did not bring to the store. I'm running DiskWarrior to be certain this is not a permissions problem, but it seems highly unlikely that the permissions are the issue. A possible solution is to install Airport Disk Utility only via disk and not via drag and drop.

Similar Messages

  • I have my Time Machine on an external drive (not connected to Airport Extreme) and I have an external HD attached to airport extreme. Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme. How?

    I have my Time Machine on an external drive (not connected to Airport Extreme) and I have an external HD attached to airport extreme. Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme. How?

    Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme.
    Sorry, but no.
    Time Machine will backup your Mac, but not the hard drive attached to the AirPort Extreme.
    Time Machine will back up a hard drive only if it is attached directly to your Mac via USB or FireWire.

  • HT4259 i connected two airport extremes by extending a wifi network.  wifi seems weak...help

    i connected two airport extremes by extending a wifi network.  all my lights are green, and airport utility confirms connections are excellent.  but the extended base station hasn't improved my wifi range in the area i set it up in.

    If you have a Mac laptop handy, run the test that I have outlined below to find out if the remote AirPort Extreme is really extending the signal at all.
    Here, I assume that both of your AirPort Extremes are the newer "square" versions....not the older "round" version.
    Locate your Mac laptop close to the "main" AirPort Extreme
    Hold down the option key on the Mac while you click on the fan shaped AirPort icon at the top of the screen
    Look for the BSSID and jot down the last few characters
    The BSSID is the AirPort ID of the AirPort Extreme
    Now, move the laptop close the "remote" AirPort Extreme and perform the same test
    If you see the same BSSID as the "main" AirPort Extreme, your Mac is picking up from the main AirPort...and the remote AirPort is not configured correctly to extend.
    If you see a different BSSID near the remote AirPort, that indicates that the Mac is picking up a signal from the remote AirPort....which is exending the signal correctly.

  • Time Machine clueless about external HD connected to Airport Extreme

    This is not my first post about HD connected to Airport Extreme. Just came back from Apple store. Spoke to Geniuses there in tech support desk and they are clueless.
    Here is situation: have 7 Macs in the house connected to Airport Extreme wirelessly. In that respect things are working fine. Last week I purchased brand new WD My Book external HD and connected it to Airport Extreme using USB (it also has Fire Wire but that is not a point here).
    As per forum advices I re-formated drive using disk utility to Mac Extended journaled, GUID. here is result:
    iMAC x 3, with Tiger - see, mount and use My Book easily, shows on desktop as mounted drive
    MacBook Pro w. Tiger - same as above, back up every day to My Book
    MacBook with Leopard x 2 - no My Book on desktop, Time Machine doesn't see it
    Mac Mini with Leopard - same as above, no trace of My Book, Time Machine doesn't see it
    * This problem evolved from me having regular 160 GB FAT32 HD connected to Airport Extreme. Again Tiger machines were using that drive every day no sweat.
    * Then I decided to upgrade all Macs to Leopard for one single reason only - Time Machine. (Good that I didn't do it but rather decided to introduce new, bigger and better USB drive first).
    * Western Digital My Book is being sold in Apple stores as "drive that is recognized by Time Machine" so I bought 1TB unit.
    * All Macs and Airport Extreme are up to date.
    Any suggestions? Thank you in advance,
    Zack

    I cannot tell you why your Apple Genius told you what he did, but he/she was dead wrong. Apple sells its Time Capsule product, so they are not interested in making the AEBS a product competitor.
    I will give you a little secret for which you will forever be indebted to me.
    Open your Terminal application in the Utilities folder and at the prompt enter or paste the following command pressing RETURN after:
    defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1
    Miraculously your problem will be Solved.

  • Macbook pro connects to airport extreme only 50% of the time

    Hi,
    I have a mac book pro that i use with an airport extreme unit. When the laptop comes out of hibernation it does not connect to airport extreme. I have to put it back to sleep and start for the second time for it to connect. Any ideas on what the problem is?
    thanks!
    MacBook Pro   Mac OS X (10.4.10)  

    Hi Laurent,
    although I was given the advice earlier that I should simply take the machine back to the shop, or call the help centre, I ended up just praying that it would be OK.  A couple of days after I posted the message I think there was an update to download and install, just a regular one from Apple from the Software Update option for the operating system or it may have been one for Final Cut Pro X, and once it installed I never had the problem again, so my prayers were answered.
    It was pretty scary at the time because I thought it must be some hardware malfunction, but because it was resolved through an update it suggested it was a software issue.  Hopefully it is the same with you.
    I'm now running 10.7.2 and have had no recurrence of the problem in many months, thankfully.
    It might have nothing to do with it, but the only other two things that may have somehow caused errors in the system startup (and I doubt these will be "unrelated" to people who know how computers work better than I do, but I feel I should mention them just in case), but I also updated Final Cut Pro X from a glitchy version to version 10.0.2 around the same time, and I also had an application installed which didn't function correctly in OS10.7 called PowerController (a simple app that can start up the computer at a set time and play music from iTunes as an alarm clock) and it was in the group of apps that were set to start at the starting up of the computer.
    Anyway, I hope your problem is resolved as easily.  Pray about it too!

  • Stopped see files on external HD connected to airport extreme.

    I have connected a 3TB external HD to my Airport Extreme.  I have been able to use and access all the files over the network through finder without any issues.  Recently I stopped being able to see the files in finder.  I can still see the dirve and the main folder but that is it and I cannot see the file structure or individual files.  This also has my iTunes files and Itunes can still connect to the file locations.  Or I can say show in Finder and it will show by but still will not show other files.  If I connect the HD directly to the computer then I can see all the files no problem.  Thoughts?

    OK...Here is where things stand:
    I am logged in as the administrator on my Computer
    When I connect the drive directly, do the Get info, I have read & write permissions
    When connecting over wifi the Permissions say, "You have Custom access"
    If I seach for an iTunes file that I know is on the remote HDD it plays
    I can show this same file in finder and see the file structure
    But I if try and open the structure top down, it won;t show access
    Through Airport Utility I Have access and can see the extrenal drive and folder is shared.
    Should "Back to Mac" be enabled?  I am not sure what other knobs to turn at this point.

  • Problem mapping USB external drive connected to Airport Extreme on my PC

    I am having a problem mapping my USB external drive in my PC running WIndows Vista.   Here is what I have so far:
    USB External Drive connected to my AirPort Extreme which is connected to my Century Link modem/router.
    I have installed the USB drive using the Airport Utility.  In the Disks section the Enable File Sharing is checked, Secure Shared Disks is set to With a Disk Password, I have entered the password in the next 2 rows, and finally AirPort Disks Gues Access is set to Not Allowed.  The section below named These Settings Configure Windows File Sharing is empty.  Am I supposed to put something here?
    I was also told I need to map the drive in my PC, but when I go to do that via the Computer and the Map Network Drive, I get stuck where it asks me to enter a folder name.  I read many of the posts which tell me I need to enter among other things the disk's ip address, but I am unable to find it anywhere.  Where do I find what to put here?
    Can someone please help this frustrated user?

    I had my USB drive on my APE working with Time Machine under 10.5.1 very reliably. A few days ago however, I needed to suspend a backup operation, and when I came back to restart it, time machine refused to mount the disk image on the drive. After several attempts to get it to connect with no luck I decided to delete the image (the sparce image file) and start over. Now TM refuses to create a new image.
    BTW, on the Mac OSX hints site there have been suggestions to start a backup with the drive directly connected, then stop the backup, move the sparce image file to the root of the drive, reconnect the drive to the APE base station to get it working. I tried this again, but I think Apple has changed something in 10.5.2, because when directly connected TM no longer creates a sparce image file.
    Anybody else seen this behavior after upgrading to 10.5.2?

  • Corrupted time machine backup on external hd connected to Airport extreme?

    I have an Airport extreme 11n (not gigabit) and a Lacie external hard disk connected to the usb port. Time machine is set up to make backups wirelessly from my laptop to this external disk. It used to work fine, but no I have the following problem all the time: Time machine complains that it cannot perform the backup. When this happens, I cannot access the drive from the finder (normally I can). I check the drive physically and I notice that it's LED show that it is constantly reading/writing (is yellow instead of red). The solution is (as also suggested by Apple support) to use disk utility and perform a repair on the drive. This solves the problem, but... only temporarily. After one or two successful backups, the same problem: no backup possible, drive not accessible in finder, disk utility finds problems. What can i do?

    Somehow I thought that with OS X 10.6 Time Machine did support disks connected to Airport devices, but I guess I'm wrong.
    The LaCie disk has indeed its own external power supply brick. Is this relevant?
    I found this article http://support.apple.com/kb/TS1550
    which is not about airport disks, but I checked my LaCie disk and it has a Master Boot Record Partition Scheme. Should I change that?
    It is also formatted as Mac OS Extended (Journaled). I thought that this was the recommended format, but checking in the Help of OS X 10.6, I found an article "Disks that can be used with Time Machine" which says: "The most common format for a Time Machine backup disk is Mac OS Extended format, but Time Machine also supports Mac OS Extended (Case sensitive, Journaled) and XSan formats"
    implying that the Extended format is more preferable than the Journaled format, right?
    I don't think the disk drive is defective: I after "repairing" it with disk utility, I could back up again, at least one time, before the problem reappears.

  • How to access from Ubuntu PC to an external HD connected to Airport Extreme

    Hi,
    I have an external Hard drive connected via USB to my Airport Extreme.
    I have a MacBook (of course) and also a PC under UBUNTU.
    I can perfectly connect to this external HD from the Mac but I don't know how to do with the Ubuntu PC.
    From Unbuntu:
    1) I tried to "ping" the Airport: it's OK
    2) I tried to "connect to a server": the Airport, nor the HD, is not seen
    Can you help me ?

    I am not sure what path I should be using in the script now that it needs to find the volume through the Airport.
    If the volume is already mounted then the path will be in the format /Volumes/<name>/... where <name> is the name of the sharepoint as it appears on your Desktop.
    If you're still unsure of the path, drag the relevant folder from your desktop into your script (or a blank AppleScript document). AppleScript Editor will ask if you want to copy the folder contents or an alias to the folder itself. Choose the 'Alias' option and you'll see the actual path to this folder appear in your script window.

  • External Drive connected to Airport Extreme, need Time Machine 3 Mac's Help

    I own an Airport Extreme and just recently added two new Macs with the Time Machine feature to our household. I would like to use Time Machine to backup to my Airport Extreme that has a 500 GB hard drive connected. It seems Apple has this blocked since they have released the Time Capsule version of the router. Is there a work around this feature so I don't have to go out an purchase what I basically have already got? Please help. We would like to upgrade our older macs to Leopard and us the same system to back them up as well. Please advise. Thank you.

    I had my USB drive on my APE working with Time Machine under 10.5.1 very reliably. A few days ago however, I needed to suspend a backup operation, and when I came back to restart it, time machine refused to mount the disk image on the drive. After several attempts to get it to connect with no luck I decided to delete the image (the sparce image file) and start over. Now TM refuses to create a new image.
    BTW, on the Mac OSX hints site there have been suggestions to start a backup with the drive directly connected, then stop the backup, move the sparce image file to the root of the drive, reconnect the drive to the APE base station to get it working. I tried this again, but I think Apple has changed something in 10.5.2, because when directly connected TM no longer creates a sparce image file.
    Anybody else seen this behavior after upgrading to 10.5.2?

  • USB External HD Connected to Airport Extreme - access from outside network?

    Hi,
    Is there any type of software that I can get that would allow me to access my shared external hard drive w/ my airport extreme from outside the network, like some type of ftp server or anything that would allow me to access it from outside my home?

    A simple way would be to share it via Apple File Sharing and FTP...
    You'll need a static Ip and a hostname, although it is easy to set up if you have a dynamic Ip too...
    Creat a free hostname on "www.dyndns.com" (for example), open your AFP and FTP ports on your router, and then use sotware such as "Rumpus" for the FTP service and tell it what drive you want to share (it can be a network drive). For AFP, all you have to do is connect to the server from the finder, hitting "Go...Connect to Server.."
    I've got my extreme drive shared globally and it works fine...just need some time and patience to set up the ports and hostnames...
    If you need help on the setup just email me... [email protected] and i'll be happy to answer any questions...

  • Can you search an external hdd connected via airport extreme

    I have my western digital 500gb harddrive connected to my airport extreme so I can use my HD wirelessly. I tried searching for files in my wireless harddrive through finder, but it doesn't seem to search it, only on my macbook itself. Is it possible to search the harddrive wirelessly?

    Smokerz,
    could you explain??
    I spent over an hour with Apple Tech support and they said that Finder/Spotlight WILL NOT search a networked drive. However, I did find a bit of a work around:
    1. In Finder Preferences: General - Select check box - 'Always open folders in new window'
    2. Open up a Finder window
    3. Select Airport Extreme. (Left column, Shared, name of Airport base station)
    4. Select networked drive
    5. Double Click a folder in your network drive that you want to search (this opens new window)
    6. In the new window, type what you need in the search window (upper right hand corner).
    Remember: The Finder window will default to the 'This Mac' in the search column (light grey line below the Toolbar)
    7. In the Search column, This Mac and Contents are selected in Dark Grey. You should see
    Search: *This Mac* "folder name" Shared | Contents File Name
    8. Now select "folder name". This will search the contents of the selected folder and bypass your Mac.
    If there is an easier way, could you please explain. TIA
    Narvon
    PS - If you try to select your networked drive in a new window as in step 5, this still won't work. You can only select specific folders within the drive. Lastly, you can move all your folders and files to 1 folder, however, this increases the search time (My network drive is 320GB in size and a search for 1 known file took just over 3 minutes).

  • Smart folder not searching external HDD connected to Airport Extreme

    I have bunch of movie files (mp4 format) on external HDD connected to the new Airport Extreme station. When I create a smart folder on either one of the machines on my local network, the smart folder would not search at all through the HDD connected to the Airport Extreme.
    I have another HDD connected directly to my PowerMacG5Quad and smart folders successfuly searches through that drive.
    However, when I ask for any type of search (i.e. any kind of files) located on a networked external HDD, smart folders acts is if the networked drive is not even there.
    Obviously, my purpose here is to have the difference machines access (RSS style) all the movies files located on the networked HDD.
    Is it some permission in Airport Extreme?

    Does this help?
    http://apple.stackexchange.com/questions/117135/access-disk-attached-to-airport- extreme-over-internet

  • Access USB external HDD connected to Airport Extreme

    Hi.
    Today I configured "Back to my Mac" and I'm having a little issue with the external HDD that is connected to the Airport.
    Let me explain the configuration: Airport Extreme (latest version) configured with Back to My Mac option, with an external HDD connected using USB port (The HDD is externanly powered). iMac computer with OSX Mavericks wireless connected, configured with iCloud Account and Back to My Mac with screen sharing).
    I can access the shared screen and control the iMac from my Macbook Air outside my home network.
    The issue is when I try to access the "network HDD" because I can connect using the right user but Finder windows never shows the HDD content. I have to disconect and reconnect to the external HDD to be able to see the files (If I have 3 windows and want to access the HDD on each of the 3 windows, I have to disconnect and reconnect 3 times).
    Question:
    There is any way to access the external HDD and be able to see its content using the configuration mentioned? The disconnect and reconnect procedure for each window is normal? There is a better configuration I can apply?. Just as information, from my MacBook Im able to see perfect the HDD content from outside my home network.
    I know the question is a little bit confusing, but if you need any additional info please let me know.
    Thank you.

    Does this help?
    http://apple.stackexchange.com/questions/117135/access-disk-attached-to-airport- extreme-over-internet

  • External HDs connected to Airport Extreme and Imovie / Iphoto issues

    I recently purchased a WD mac edition "my book" hardrive in order to store all my imovie, iphoto and itunes files externally. I connected the hard drive to my airport extreme base station but was unable to move my imovie files to the hard drive. Instead I received some derivation of the following message - "volume not compatible." After being transferred to a number of different people at apple support, I was finally told that the imovie, iphoto etc... are not compatible with hard drives that are connected wirelessly. I cannot believe that this is the case (presumably imovie files can be saved on timecapsule). I would be most grateful if someone could help me out here.

    I was finally told that the imovie, iphoto etc... are not compatible with hard drives that are connected wirelessly. I cannot believe that this is the case
    Nor can I. Files are files, some are bigger than others but to a hard disk, they're all the same.
    I would presume that you don't get this message when connecting your My Book directly to the computer's USB port?
    Apple Support simply couldn't have understood you correctly. I wouldn't expect to use iMovie or iPhoto to manipulate remotely stored files, but merely copying them for archival purposes is a completely legitimate use for the external HD.
    This makes no sense. Perhaps you could post your question in an iLife forum.

Maybe you are looking for