External HD "Not Readable" after Boot Camp Installation

After installing Windows XP on my Mac, I switched back over to OS X and tried to access my external hard drive which greeted me with the message: "The disk you inserted is not readable by this computer." I assume that the Boot Camp process must've affected the external drive and made it incompatible with OS X. The external does show up in Disk Utility, but there are no options to repair the disk, only erase. Can anyone tell me how to reformat the drive, without losing all of the precious data on the disk, for OS X?

XP can't see Mac OS file system.
There is your drive, and your volume_name on the left side column. You have to click on volume_name and select the tab for Repair.
Best to backup before installing or updating any OS, and leave everything you don't need disconnected.
I doubt anything changed, should not have.

Similar Messages

Can not boot into OSX after boot camp installation and resizing of Macintosh HD

So from the beginning what I was trying to do was set up my iMac (27-inch, Late 2013) with boot camp so that I could play some old windows based games that can not be played in Parallels.
I went through the Boot camp process and everything set up just fine.
I had both OS X Yosemite 10.10.2 and Windows 8 Professional running but as I was installing games on to boot camp I discovered I did not allocate enough space and needed to extend the Boot Camp partition.
I used boot camp utility to set OS X as the default start up disk and had it restart
I launched into OS X and used Disk Utility to shrink Macintosh HD another 120GB
Restarted again holding option and launched into Windows
Used the disk management in windows to try and extend the boot camp partition into the unallocated space.
It was not an option to extend it so I tried to create a new simple volume from the unallocated space then delete it and try to extend it again.
It still was not an option.
From there I went to restart again while holding option and the only options I had were 10.10 Recovery and Windows
I tried using disk utility in recovery and Macintosh hd now only showed disk0s2
I tried to verify and it could not verify
I tried to repair and it could not repair.
I put the iMac in target disk mode and using a thunderbolt cable I tried using disk utility from my MacBook Pro (13-inch Mid 2012)
Verifying volume “disk2s2”Verifying file system.** /dev/rdisk2s2
Invalid BS_jmpBoot in boot block: 000000
File system check exit code is 8.Error: This disk needs to be repaired. Click Repair Disk.
Verify and Repair volume “disk2s2”Repairing file system.** /dev/rdisk2s2
Invalid BS_jmpBoot in boot block: 000000
File system check exit code is 8.Updating boot support partitions for the volume as required.Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
This is the same error I got on my iMac
I used terminal diskutil list and got:
/dev/disk2
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *1.0 TB     disk2
   1:                        EFI EFI                     209.7 MB   disk2s1
   2:       Microsoft Basic Data                         799.3 GB   disk2s2
   3:                  Apple_HFS Recovery HD             650.0 MB   disk2s3
   4:       Microsoft Basic Data BOOTCAMP                70.3 GB    disk2s4
I can see that Macintosh HD was disk2s2 but it now shows its Microsoft Basic Data.
I did not format this partition and it was working fine till I restarted the computer after resizing Macintosh HD.
I am not sure what I can do to fix this.
I've found multiple articles about similar issues, but the issue thet they have was that they could not boot to Windows instead of my issue not booting to OS X

****************    Update    *****************
From the Windows Partition using Disk Management I can see that the drive is still labeled Macintosh HD and that all of my data is there.
I have a complete backup so i'm not worried so much about the data.
What I'm most interested in is trying to solve this issue because I'd like to continue using boot camp and I actually work with mac computers and would like to be able to help others if this issue arrises again.

MacBook Pro 13" Late 2011 Experiencing Significant Slow Down After Boot Camp Installation

     Okay, so today, after installing Windows 7 on my MacBook Pro via Bootcamp Assistant, I experienced significant performance slow down (fans going at full blast, applications opening after extended periods of time, keystrokes not being registered) when I returned to my OS X partition/second hard drive. I have dual hard drives, one of them being a Samsung 256 GB SSD with OS X Mavericks and the other being my original 500 GB HDD, divided into a 250 GB OS X Mavericks partition and a 250 GB Windows partition. I have the SSD set as my startup disk and I have it located in the main HDD bay. I moved the old HDD into a caddy and placed it where the optical drive normally should be.
      After multiple failed attempts to install Windows via USB and Bootcamp Assistant, I decided to reinstall my optical drive and use a Windows installation disk. This attempt proved successful, and I was able to install Windows 7 onto the 250 GB partition I had created for it on the 500 GB HDD. After completing basic setup of Windows, I removed the optical disk drive and reinstalled the SSD and the HDD into their original spots (SSD in the main HDD bay, HDD in the caddy where the optical drive normally is).
     After completing this tedious process, I booted my Mac back up using the SSD. However, I noticed something was wrong when the login screen, apps, and nearly everything else on my desktop had slowed to crawl. I decided to check my Activity Monitor to see what the problem might be. Activity Monitor told me that the task "kernel_task" was taking up anywhere from 200-600% of my CPU, which explained the slowdown in performance. I looked around to see if there were others with the same problem as me, and I found that Spotlight Indexing might be an issue, with a potential remedy being move my Bootcamp Partition into the Privacy section of Spotlight under System Preferences. After doing that, I experienced no increase in performance and everything was still going very slowly.
     The next step I took was to see if booting into Safe Mode would help the issue. After booting into Safe Mode on my SSD, I noticed that things were back to their normal speeds, with applications opening at the speed they should be and keystrokes being registered instantaneously. However, the fans were still going and had not shut off once booting into Safe Mode. In addition, I checked Activity Monitor and the "kernel_task" in question was no longer taking up massive amounts of the CPU.
     At this point, I don't know what to do and I need help in restoring my Mac to original speeds. I may end up deleting my Boot Camp partition as a last measure if all else fails, seeing as I installed Windows in the first place for running a few programs and games that I can live without. However, I'd prefer to not have things come to that and fix things before deleting the Boot Camp Partition. I've heard that if everything runs normally in Safe Mode, then the issue is third-party software. Is this true?
     Any help would be greatly appreciated as I am writing this from the MacBook in question in Safe Mode because it's essentially useless in normal SSD operation.

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
Copy a line of text in this window to the Clipboard.
Paste into the window of another application.
Wait for the test to run. It usually takes a few minutes.
Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' \*AutoCad \*dropbox \*GoogleDr\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/ { next;} /(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' '" L*/P*/*loginit*' 'L*/Ca*/com.ap*.Saf*/E*/* -depth 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D13 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 4 3 32 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start Time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

After Boot Camp installation, Kernel Panic when launching OSX partition

Hey guys. I have a mac mini (early 2009) with Mac OSX 10.6.2 running. I installed XP Professional Sp3 using the Boot Camp Assistant with no errors. It works fine. However, whenever I launch the OSX partition, even in single-user mode, it Kernel Panics. What can I do to stop this?
I have a legal copy of XP and OSX, by the way.

this does not sound like a problem with anything on your drive then but rather a firmware issue. just to make sure, how are you booting from the DVD? reboot and hold "c" at the chime. any luck? if not reboot and hold option at the chime. this ought to boot you into startup disk manager where you can choose what to boot from.

Windows 7 Pro not finding network connections after boot camp installation. Is there something special we have to do to get the network (wired and wireless) set up?

Any suggestions for getting the network connections working on Windows 7 Pro running on a Mac Min with OSX Lion?

tim-bob wrote:
Any suggestions for getting the network connections working on Windows 7 Pro running on a Mac Min with OSX Lion?
If you haven't yet installed the Windows Support Software, that's probably why, so install it now.

Gray screen during startup after boot camp installation

I cannot either Mac and Windows t start on Mac Mini after I updated with Windows7 on Bootcamp.

Hi there Sudarshan21,
I would recommend taking a look at the troubleshooting steps found in the article below.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
-Griff W.

Boot Camp Installation: Definition of, and insights into "External Drives"?

I'm recovering from a logic board failure. One casualty was that I lost my prior Boot Camp installation of Windows on my main internal hard drive. :-( Wondering if I can install Windows anywhere other than the main internal hard drive so I can maximize space on my OSX main internal drive?
From what I've gathered, installing Windows 7 Boot Camp is very difficult (and perhaps impossible?) on an external hard drive. However, what's not entirely clear is what constitutes an "external drive".
Questions:
1. Can I install a bootable installation of Windows 7 using Boot Camp (obviously not running OSX in this scenario) on either the:
A) Data Doubler 7,200 drive
or
B) Express Card 34 SSD drive
2. Can I also install Parallels (on the main internal OSX drive), then while in OSX launch (a much slower) Windows from location A or B?
Context:
1. On a late 2011 MBP 17' (version 8,3), I've replaced the stock hard drive (7,200 rpm) with a much faster OWC SSD Drive. (Awesome upgrade, btw!)
2. The internal apple dvd device was removed and the stock hard drive was inserted in this location using OWC Data Doubler. (Also, very nice.) An extra challenge here is that the dvd drive is now an external device. I have a Windows 7 install disc, but I'm not sure if it will be recognized during the installation process?
3. This model MBP has an ExpressCard 34 slot, for which I can buy an SSD drive. Never used this slot and have read mixed reports on boot ability.
Any and all insights greatly appreciated!

Yoüf wrote:
Many thanks for the helpful response, Loner T. I think I've got it. To install Windows through BCA on the Optibay drive, I temporarily move it to the main SATA bay. I can then temporarily put the DVD drive back in the Optibay. So here's a question: In doing this, I would no longer have an OSX boot drive (since I'm temporarily removing my OSX boot SSD). It's been a while since I used BCA, so my memory is fuzzy (sorry), but does the BCA process need a working OSX install on the drive in the SATA bay?
The SSD with OSX boot is normally (for your specific scenario) kept in an external enclosure (USB/FW/TB) to boot from and run BC and partition the disk in the main SATA bay.
You mention that modifying the BC info.plist causes issues. I lost you a little here. Using the method you describe (move the Optibay drive to the SATA location, run BCA to install Windows, then move the drive back to the Optibay location), does the BC info.plist need to be modified or not? If yes, a few more details would be welcomed. If not, what prompted this thought?
If you have a functional Optical drive and the designated Windows-to-be in the proper bays, the BC info.plist modifications are unnecessary, and can cause other grief, and are best avoided.
Thanks also for the bleeptobleep post. It says to use a USB3/Thunderbolt external drive (which I do have); however, my MBP (version 8,3) only has USB2 ports. I realize that a USB2 port will read a USB3 external drive, but was wondering if this limitation is a deal breaker for a bootable Windows system, or if it just means that things will be really, really, tragically slow due to low transfer rates. Any idea on this aspect?
USB3 can cause problems for Windows 7 installer, bot not as many issues for Windows 8+. It is better to stick to USB2, but you are correct it will be slow. OSX can boot and will use RAM much more aggressively, unless it has to go back to the USB (2/3) when things may give you a beach ball. Windows 7/8 are less friendly for caching the whole OS and applications in RAM, and may be slower. A TB connection is much faster (TB2 even better).
BTW: Bummer that the ExpressCard slot can't work for booting into Windows. That would be pretty slick. I've seen some older posts by folks who were once able to do this, but seemingly only with early versions of OSX. Apparently newer OSX versions either did away with this feature, or seriously complicated the process. Would love to find a workaround if one exists.
You can test it, but may have some issues finding storage for ECards.
(Dumb question: on this forum, how are you threading comments into a quoted block of text? Are you using HTML or is there some easier way?)(((
Under the "Reply" bar at the top, there is an icon with a "quote" and a "speech" bubble, which is used to quote posts. You can either quote from a previous post, or select a line (or more) of text and click on that icon.

Vista Blue Screen after Successful Boot Camp installation (32 and 64 bit)

OK so there are a number of people with issues relating to the BSoD after a successful (or not) implemetation of Bot Camp and Windows XP and/or Vista. One of the identified problems relates to the NVIDIA GEforce 9600m GT display driver which crashes out AFTER windows performs its update routine.
Having removed and installed the partition (to ensure a clean install each time), the inescapable conclusion is that the NVIDIA driver is to blame for the crash dump, but it is one of the many MS updates that is the root cause of the failure. If you do a clean install of Vista 32 or 64 Ultimate and install the Boot Camp 2.1 (build 1256) and DO NOT allow updates, the system is not only stable, it runs like a train!
I have Contacted AppleCare about this (as my new MBP is only a few days old) and they have not even heard of the problems. NVIDIA have obviously got issues with something as the driver has been updated to a BETA on their web site, but this will not work on a Mac as it cannot seem to find the hardware to allow the update to complete.
If (like me) you have bought an MBP for support issues for both Mac and Windows users, this is a showstopper and one that is about to cause me to ask for my money back. So far, the nice shiny and new MBP is back in its box pending a 140 mile trip back to Exeter from whence it came.
SHARK!

Boot Camp was a response to public challenges at the time to see who could find how to install Windows on a Mac - which is totally okay thing.
Then you want Apple to do more than any normal PC vendor selling a laptop where people have to do things like deal with BIOS, drivers and all the things you have had to deal with, for Windows.
I'm not disagreeing, let alone arguing, I agree that hardware abstraction layer type stuff Apple would need to do. But I don't think Apple needs to do more than get Windows installed. Drivers, AV, and all the stuff that comes with Windows doesn't change. But it should not BSOD when you install something you are told you need.
I wouldn't be surprised though to see Windows 7 eventually support Apple hardware out of the box so to speak.
Cookie cutter answers are part of today's customer experience "level one" is no level at all, but a lot of times - and it takes a lot of work - to translate feedback and problems into "cook book" before you get to the troubleshooting (level 2 and above).
Which is why I read sites like MacIntouch; subscribe to MacFixit (tons of articles on a CD along with shareware). And books.
Nvidia has terrible drivers in OS X on the Mac Pro (workstation) while ATI has had very good drivers and OpenGL support.
I prefer to have more choice and freedom when it comes to drivers. As for engineering and how things get qualified (use to see even SCSI hard drives had to be qualified for both the OS; the controller to be used; driver version; firmware; etc).
What I see is the first shipped BIOS/EFI firmware on any device or system is not the one you want.
Back in the 70's I was introduced to "bleeding edge" but we would get premiere on-site support if we were willing to install, adopt, some new IBM service, software/hardware. And sometimes we were there on Sunday on holiday weekends.
One person just could NOT after doing everything under the sun, get Adobe CS4 to install on their new $5000 Mac Pro 2009. Got a new system, worked perfectly.
In 2008 Early Mac Pro, most all systems would freeze on wake from sleep. Took two months before an EFI update was issued that cured the problem. There is/was also a problem with "inrush current" and PSU.
I had Blue Screen with Vista. Repeatedly.
At first I thought it was a new MICROSOFT 4000 keyboard.
Later I wondered if it was my Apple OEM Nvida 7300GT (and some are failing but it worked in OS X) so I bought 2nd, a PC 8600GTS.
And pull 3rd party PCI Express controllers (FW800, SATA 1x, SATA 8x cards).
Came away and thought "oh, it was the 3rd party card" when that seemed to work.
Around the same time I had bought a new WD Caviar 750GB SATA drive.
It was that drive that would cause problems with Vista after the install.
I thought it was something in Microsoft Windows Update that was causing my personal ****, not my equipment. And MS for their drivers. Somebody else's.
And mind you, I would go through install half a dozen times, try installing Boot Camp before updates, after updates, not at all, add AV software.
I finally -- after a full year -- learned a lot (don't learn from things just working and I still say it has always been "Plug and Pray" PnP ) things work. I know the frustration and aggravation and the wish that things were different somehow.
The BSODs that I got were not from Apple Boot Camp. I even ran my system w/o Boot Camp for six months. And this time, with Win7, everything worked fine, wake, sleep, networking, no need for Apple drivers. At all.
I hang out on a forum where people build their own, X58 board, Intel Core i7, eVGA graphics. And how to get even DDR3 to work, and then how to get the most out of and push it to the extreme, then throttle back a notch.
The nice thing about that is you learn from it, like you do from racing and sports, to build a better mousetrap.
Nvidia is bleeding. Even as they and ATI want to stay on leading edge. Intel is contracting (even as they have their best cpu technology ever coming out) and costs that should go into R&D may be harder to "justify" or all the prototype programmers engineers and testing labs. Everything is more commoditized than ever.
Bottom line: I have Leopard 10.5.6. It has Boot Camp 2.1.2 version, later than the 2.1 download. And there has not been a single update posted online. But my original Leopard DVD 10.5.0 has the SAME contents packaged as 2.0 as were in the 1.4 Beta. I spend $129 for a new DVD to get the latest drivers. Make sense?? of course not.
Oh, and my Mac with 64-bit hardware, cpu, the EFI BIOS is 32-bit so no official support from Apple to install BC 2.1.2 or use Vista 64-bit. Snow Leopard will be 64-bit kernel, require and enforce 64-bit drivers. Should be interesting. Because technically, and logic, would say I don't have a true 64-bit BIOS environment.
Got an iMac? not supported with 64-bit. MacBook 2008 had 64-bit support, but not the "Late 2008" there you need MacBook Pro. And yet everyone wants to address more than 2GB (Apple EFI32 allows access to 3.3GB on some, 1.9GB on others, and in my Mac Pro? limited to 1.9GB memory in Windows.... so you know I don't want to run a Xeon workstation in Windows 32-bit.

Mouse not working with Boot Camp after 10.5.7 update

I upgraded to 10.5.7 recently, and now my mouse doesn't work on Boot Camp. It doesn't seem to register, and I can't move the pointer. I tried this with two mice that worked just fine on the Mac OSX side. Any ideas? Has anybody else noticed this?

I have a new (July 2009) iMac24 and neither the wireless mighty mouse nor keyboard work with Boot Camp XP Home Edition SP3. They install OK with the Bluetooth control panel, but then after five or ten seconds, drop out of the control panel and have to be discovered again. I spent two hours today with a Mac support expert, but no joy. We both gave up. It seems the wireless mouse/keyboard does not work with Boot Camp. If anyone hears of a solution, please let me know.

"Your bootable USB drive could not be created" "Boot Camp only supports 64-bit Windows installation on this platform. Please use an ISO file for 64-bit Windows installation."

I try to install windows7 system on my macbook air, which version is 10.8.5. When I open the bootcamp, it let me to choose a windows ISO image, which I've already downloaded from this website: http://www.w7forums.com/threads/official-windows-7-sp1-iso-image-downloads.12325 /, it also asked me to select a USB drive, which is kingston that has 8GB. Then when I clicked "continue", it said that "Your bootable USB drive could not be created" "Boot Camp only supports 64-bit Windows installation on this platform. Please use an ISO file for 64-bit Windows installation." But actually the ISO image I downloaded is 64-bit windows7. I don't know why this would happen. Could someone help me please!!

Thanks for your feedbakc Kiranjj!
I identified the reason to be that the W8 installation file didn't download completely from a Mac OS-device. I downloaded from another Win-device and the moved the installation file with a USB-stick and then everything worked diectly! But thanks anyway.

Magic Mouse Not Working with Boot Camp.

Hi All,
I have a wired issue here. I installed Windows XP on my iMac 27" using bootcamp and all worked fine till one day my Magic Mouse stopped working in Windows. Now the funny part is windows is able to detect my mouse and says that the device is working normally but the green light under my mouse is OFF. No matter what i try i cannot get it to come on. But the moment i boot to Mac OS X the mouse works perfectly fine. My Apple Wireless KB works just fine in Windows. A USB mouse also works fine. I have also installed Parallels on my Mac and when i boot into the Windows partition using Parallels the Magic Mouse works fine. Any idea as to whats going on here.?
John.

I have a new (July 2009) iMac24 and neither the wireless mighty mouse nor keyboard work with Boot Camp XP Home Edition SP3. They install OK with the Bluetooth control panel, but then after five or ten seconds, drop out of the control panel and have to be discovered again. I spent two hours today with a Mac support expert, but no joy. We both gave up. It seems the wireless mouse/keyboard does not work with Boot Camp. If anyone hears of a solution, please let me know.

Parallels install after Boot Camp

I have a new Macbook Pro on the way and am trying to figure out the best way to install Boot Camp and Parallels and only activate my copy of Windows XP one time. Do I install Boot Camp first? Parallels first? Any help from someone who has done this would be very helpful.

I suggest you download the Boot Camp software from Apple and read the documentation carefully. Visit the Parallels' site where you can also download a copy of the documentation and read it carefully. Both docs explain how to install the software. The Parallels' doc will explain how to use a Boot Camp installation for a VM. However, if you use Boot Camp there's no need for Parallels (and vice-versa.) Having both is a duplication of effort that's really not necessary.
If you need information or support for Parallels then visit their forum: http://forum.parallels.com/. The Apple Discussions does not provide support for Parallels.
For Boot Camp support visit the Boot Camp forum which is a separate forum in the Apple Discussions.
Why reward points?(Quoted from Discussions Terms of Use.)
The reward system helps to increase community participation. When a community member gives you (or another member) a reward for providing helpful advice or a solution to their question, your accumulated points will increase your status level within the community.
Members may reward you with 5 points if they deem that your reply is helpful and 10 points if you post a solution to their issue. Likewise, when you mark a reply as Helpful or Solved in your own created topic, you will be awarding the respondent with the same point values.

HT1899 How do i boot to mac after boot camp

How do i boot back to mac after boot camp? I was in the middle of installing windows 7 when i received an error message saying the partition needs to be in a diff format ( NFTS ). I tried restarting my mac but now its saying "no bootable device - insert boot disk"

Welcome to the Apple Support Communities
You have to format the volume using NTFS in Windows installer. After you've installed Windows, press X key while your computer is starting to start in Mac OS X

BSOD w/Vista 32bit after Boot Camp 2.1 update - bluetooth related?

Ok, so 2.1 has officially hosed my Boot Camp installation now - I was really hoping for access to more than 2GB of RAM on my Mac Pro but instead I'm blessed with BSOD every 20 seconds - thanks! This seems to be somewhat random but I figured out that I can actually cause it pretty easily by opening Internet Explorer 7 and trying to type into the Live Search bar - I'm using an Apple bluetooth (aluminum) keyboard and it almost seems to be related - my password doesnt show up when I type it in at Vista log in either and its really funky when it does work.
I installed my Boot camp drivers from the Mac Pro (2008) disc that came with my MP - didn't have any troubles with those - all I really wanted was to use another GB or 2 of RAM..... instead I get constant lockups.

You need the 64-bit version of Vista for one thing to use more than 1.9GB RAM.
Most of the problems people have with SP1 update have been pre-existing 'dirty file system'
To backup or clone Vista, I would use WinClone from OS X, or use Vista Businss/Ultimate before hand to backup files and system and make sure you have a good restore point before applying updates. Taht is one thing I would like to see Apple do, which MS updates often will.
http://windowsvistablog.com/blogs/windowsvista/archive/2006/12/05/windows-recove ry-environment.aspx
http://www.twocanoes.com/winclone/
What to do when Windows crashes:
http://www.informationweek.com/news/windows/showArticle.jhtml?articleID=20000032 9

I have deleted windows7 in the boot camp but the partition macintosh hd2 is still there...if i try to install windows7 again,it is not showing the boot camp partioned space...

I have deleted windows7 in the boot camp but the partition macintosh hd2 is still there...if i try to install windows7 again,it is not showing the boot camp partioned space...

Update: I did an extended hardware test (just in case a hardware issue was causing my problem)--no problems found. I then went through the Aperture troubleshooting steps: I tried repairing permissions first, but I still could not see any of the images that were in the Aperture trash. I then repaired the library. This seems to have fixed things (at least upon initial assessment). Afterward, I was able to see the images that were in the trash. I opened the Activity Window to see what it said when I tried emptying the trash again. This time it said it was deleting exactly the number of images that I expected it to delete (not twice as many this time!), and it emptied lickety split--as I had expected it to do the first time! So, hopefully, all is now well with my system and library. Still wondering why it was telling me it was deleting twice as many images as were in the trash the last time I tried, but overall, much happier today!

External HD "Not Readable" after Boot Camp Installation

Similar Messages

Maybe you are looking for