External Input is no longer detected in my System Sound Preferences?
When I go to System Preferences>Sound> on my Powerbook, I no longer have the option to switch to an external input or external microphone. It only lists the Internal Microphone. Why has the external option disappeared?
If you used system cache cleaning software it can mess up Apple software. Stop using such software. Remove Mackeeper if present using these directions:
https://discussions.apple.com/docs/DOC-3691
If you started typing something in the search field of the System Preferences, it might be hiding. Quit and reopen System Preferences to be sure it isn't hiding because it is searching for another panel.
Lastly, if none of the above apply, go to your hard drive -> System -> Library -> PreferencesPanes folder and see if it is hiding there. If it isn't, get your 10.5 installer disc that installed 10.5 on your Mac, and restore it with http://www.charlessoft.com/ 's Pacifist, and then run the 10.5.8 combo update to ensure the version matches the operating system.
Similar Messages
-
Why does my internal speakers no longer show up in my sound preferences?
In February, I updated my MBP 15" to 10.7.3. After restarting my system, the internal speakers were no longer listed in my available outputs under my sound preferences. I wasted an hour of my time talking to phone support only to hear the same stuff I had found online to try to troubleshoot the problem. Finally they told me to go to the Genius Bar. I went to my local Apple store where they proceded to look at it for about an hour and in the end told me the way to fix it would be to just wipe the harddrive and reinstall OS X. I couldn't afford to do that at the time due to needing the computer for grad school and chose to wait till after school let out to do this. Now I have wiped the harddrive twice and reinstalled and STILL don't have sound.
Does anyone have any ideas of what I can do to try to fix this?It's a longshot, but you could try this:
Resetting your Mac's PRAM and NVRAM -
My iMac no longer detects my apple external monitor
As a teacher, I moved classrooms this school year. After the move, my external monitor is no longer detected by my iMac. I've connected the cords just as they were previously. When I go to the Systems Preferences > Display, there is no Arrangement tab. Please help!
Hello cbecnel
There are a few things to try and they are outlined in the article below. One is to try a different cable and another one would be to try that display with another computer to help isolate the issue.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Thanks for using Apple Support Communities.
Regards,
-Norm G. -
After I installed Lion, my MacBook Pro can no longer detect my external hard drives or my USB flash drives. What should I do?
And me -- My Mac at work running Snow Leopard reads the drive normally. My home Mac (on Lion) can't even find it....
Yet another Leo let-down..... -
External display no longer detected
I was prompted to install the iMacEFIUpdate1.7 & ThunderboltSoftwareUpdate1.1 automatically this evening and after the update my external display is no longer being detected, before the update everything was working fine. Its connected from one of the thunderbolt ports to an HDMI port on the display
I've tried to manually install the updates again, the ThunderboltSoftwareUpdate1.1 installed again with no errors but the EFI update pkg will not run, if gives me a message saying that 'The software is not supported on your system.'
I've rebooted numerous times, tried different display ports and a different cables but nothing seems to work. Any ideas would be greatly appreciated.
(I'm also running 10.7.2 on a 3.4GHz intel core i7, not sure if that helps)I too am having issues getting external display activated for two different animation programs. One worked for a while, then the "Full Screen" option failed. It did not work on the other animation program (Modul8 & Arkaos). I'm on MBP and upgrated today to 10.5.6 which could be the source of the problem. I don't know what other connector to get between the cable from the monitor into the computer. Also, the output window (in Modul8) no longer works, even without full screen mode activated. I've quit program, rebooted, turned off monitor.
I've another cable for video projection I may try later.
External monitor is seen by system and is otherwise functional.
Help! I've work to do. Thanks. -
SP2-0027: Input is too long error during Apex 4.0 installation
I have come across an error while installing Apex 4.0.
The installation reached the point where it gave a SP2-0027 error
...PAGE 72: Workspace Schemas
...PAGE 73: &PRODUCT_NAME. Workspace Creation
...PAGE 74: Page Views By Day Report
...PAGE 75: Page Views by Application and Page
...PAGE 76: Hourly Usage
...PAGE 77: Usage by Application, for selected hour
...PAGE 78: Page Performance Dashboard
...PAGE 79: Database
SP2-0027: Input is too long (> 2499 characters) - line ignored
wwv_flow_api.create_report_region (
ERROR at line 16:
ORA-06550: line 16, column 1:
PLS-00703: multiple instances of named argument in list
ORA-06550: line 16, column 1:
PL/SQL: Statement ignored
Disconnected from Oracle Database 10g Express Edition Release 10.2.0.1.0 - Production
Following this, I looked up Apex help, and so checked dba_registry
C:\apex>C:\oraclexe\app\oracle\product\10.2.0\server\BIN\sqlplus /nolog
SQL*Plus: Release 10.2.0.1.0 - Production on Tue Jul 13 15:40:05 2010
Copyright (c) 1982, 2005, Oracle. All rights reserved.
SQL> connect sys as sysdba
Enter password:
Connected.
SQL> SELECT STATUS FROM DBA_REGISTRY
2 WHERE COMP_ID = 'APEX';
STATUS
LOADING
Please help
Edited by: user4477408 on Jul 19, 2010 3:35 PM
Edited by: user4477408 on Jul 26, 2010 11:29 AMDid you keep any kind of external references to your pages/reports? From what it looks like, one of your report regions exceeds 2500 characters and APEX is having a hard time crunching it. See if you can find that page, then export that page, delete the region, and import the page on it's own later.
Not sure why it would be such a small area, though. I usually don't have any trouble until I hit 32K characters. -
External speakers are no longer working, why?
Ive been Apple Airplay and now my external speakers no longer work on my imac, it is something to do with Airplay or is there something that I need to fix or reinstall? Look forward to hearing from you. TIA
Hi,
There are no external speakers in Sound Preferences/ Output, only internal speakers, or if you plug something into the output port, Headphones, or a sound interface device. Hold down the Option key and click on the sound icon in the top menu bar on your display and you will see the options for output and input.
Have you got an audio system plugged into the output port? If it is not working, check your cables. -
Can we give an external input to 5610 upconverter
Hi,
This is just to clarify a
technical doubt concerning with NI RFSG..
We have purchased two PXI 1033 chassis(one with
5610 upconverter and the other with 5600 down converter) for our project...Now
we are trying to test the transmiter system only..We have
successfully installed the transmitter system consisting of the chassis with
5610.The OS has successfully detected the system.Next comes programming of 5610
to get an RF output of desired RF frequency and power level.For this we
connected an external IF frequency source from a signal generator(IFR
2050T)because we don't have AWG in the chassis.We have completed
setup,configuration and self-testing of 5610 in MAX and the RF output from 5610
was monitored using spectrum analyser (HP MS710A).Unfortunately we are not able
to program 5610. The VI was similar to fig 19 of "Getting Started Guide NI RF
SIGNAL GENERATORS".When the VI is run, the following error comes"session could
not be opened because the AWG resource name was not specified.Specify the AWG
resource name in the MAX or in the option string".
Please clarify whether we can program 5610 with an
external IF signal independent of AWG(because our system doesn't contain
AWG)
Looking forward for your immediate reply.
Thank
you.Hi ,
This is Faris Alhorr from national Instruments.Before answering your question, let me clarify this. I believe that you sent an email yesterday and for some reason whenever I try to reply to it keeps on bouncing back. ( it could be that you supplied the wrong email address).
To answer your question, you can use the 5610 in upconverter mode only. There's an example in LV that shows you how to do that.
You can find the example in LV under Help >> Find Examples >> Hardware Input and Output >> Modular Instruments >> NI-RFSG >> Utilities.
Also make sure that you are setting the AWG in MAX to external. You can do so by right clicking on the 5610 in MAX.
I'm glad that you posted here, and please let me know if you have any other questions.
Best Regards,
Faris Alhorr
Bueller -
RSYST-CODE-input data too long
we have implemented ESS on EP 7..when we try to naviagte through my workspace and if select any services such as Performance Mangement , Leraning and development it will take us to a screen where prompt us to log for Production system ,,...
Service :WEBGUI
RSYST-CODE-input data too long
if i give necessary acces it will connects to the R/3 ..
is there any coonection based configuration to be check in order to by pass getting this screen..
regards
BuddhikeHi Lynton,
As mentioned in the thread you listed, it is possible that this error is being caused by using certain characters, such as ü, á, $, &, -. In order to check if any catalog has strange characters, please check in transaction SPRO -> Supplier Relationship Management -> SRM Server -> Master Data -> Define External Web Services. Check in "Web Service ID" if any catalogs contain strange characters.If so, remove them and retest the issue.
Kind Regards,
Conor Harkin -
Windows no longer detecting my Audigy 4?(Non-P
Hey all. I've had my Audigy 4 (non-Pro) installed and working super for about 50 days, but it started giving me a weird problem. Windows was no longer detecting the card! It was weird. DX Diag, programs like EVEREST... they all report no sound card whatsoever.
Here are my PC specs:
XP Home Edition
Albatron K8X800 Pro
S754 3200+ ClawHammer
x 2 OCZ ELPE 52 MB(2-3-2-5)
Visiontek XTASY X850XT PE
x 80 GB SATA 2 Seagate, x 80 GB Maxtor
Some other things to note:
XP has been repaired. Went from Service Pack , updates, and all the way to Service Pack 2. The card requires XP w/SP2, yes, so I have that covered.
Onboard audio is disabled through the bios. I have AC'97 integrated audio on this.
My motherboard has fi've PCI slots - although I can only access 4 because my video card is in the way, and I have tried three of those and I get the same problem.
I have tried it in other PCs in my house, double-checked each time - so it is not ESD as I originally believed. It works just fine on those PCs. It is being not located only on MY PC.
So guys and gals, I do not know what to do... I am stumped. It's the weekend so I can't call Creative support until Monday. I don't want to request an RMA through my warranty because clearly it's just a problem with my PC. What should I do?!Message Edited by Celsius on -26-2005 07:36 PMDevice not recognized in iTunes
-
My external drive is no longer displaying on my desktop
My external drive is no longer displaying on my desktop - Any suggestions on how to solve?
Thanks ;-)Finder -> Preferences -> General -> Show these items on desktop -> External disks
-
Iphone is no longer detected on itunes/computer it is synched with.
One of my Iphones is no longer detected by the itunes/computer that it is synched with. The computer/itunes does detect other devices. The iphone in question is able to be detected on another computer/itunes.
I updated software oof iphone on another computer. I updated itunes on the computer that does not detect the phone. I rebooted both. I tried software conflict.
Does anyone have an idea how to resolve? I have all of my contacts, apps, photos, music etc on that computer.
When I updated phone software on another computer to see if that was the problem it wiped out all music,apps, photos etc on the phone. I have thee devices with one apple id and they are synched to different computers.You should try another USB cable, charging and sending data through the cable is not completely the same, sending data is using other contacts inside the plug or docking connector.
-
Windows XP is no longer detecting the iphone
Out of the blue my desktop is no longer detecting or charging my iphone. It doesn't show up in device manager either.
I have reinstalled all software,drivers and no luck. All services are running.
It works fine on my laptop and charges fine on the wall charger.
I have tried my friends iphone on the desktop and it also does not get detected, so I assume it has to be some software problem.. Any ideas?Hello,
I have a similar problem now. Only addition is that the phone itself is not working either and when i connect to comp it results in opening of 'Found New Hardware wizard'
Did you find solution to your problem??? -
I have a MacBook Pro, 10.10.2 Yosemite. My external hard drive no longer appears on my screen or in Time Machine. I have gone into Disc Utility to repair disc, and get the message: Error: Partition map check failed because no slices were found. I was trying to follow Melophage's instructions by going into "Terminal" and entering "diskutil list; diskutil cs list; mount" and "diskutil info disk2." Then I entered the command "sudo got show disk1." I am sure I have made the problem worse. Can you give me some help? Thank you. blelambert
Last login: Wed Mar 11 19:23:03 on ttys000
~ belambert$ diskutil list
/dev/disk0
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *251.0 GB disk0
1: EFI EFI 209.7 MB disk0s1
2: Apple_CoreStorage 250.1 GB disk0s2
3: Apple_Boot Recovery HD 650.0 MB disk0s3
/dev/disk1
#: TYPE NAME SIZE IDENTIFIER
0: Apple_HFS Macintosh HD *249.8 GB disk1
Logical Volume on disk0s2
7A998EAE-68FB-4BAC-BF40-7A31D2806B2C
Unlocked Encrypted
/dev/disk2
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *2.0 TB disk2
1: Microsoft Reserved 134.2 MB disk2s1
~ belambert$ diskutil cs list
CoreStorage logical volume groups (1 found)
|
+-- Logical Volume Group 883A56F4-5559-4872-A8DA-960F99655B63
=========================================================
Name: Macintosh HD
Status: Online
Size: 250140434432 B (250.1 GB)
Free Space: 8921088 B (8.9 MB)
|
+-< Physical Volume 7EDAFA20-FF9A-45FB-BA44-6526BB46C381
| ----------------------------------------------------
| Index: 0
| Disk: disk0s2
| Status: Online
| Size: 250140434432 B (250.1 GB)
|
+-> Logical Volume Family B47B0B40-CBF2-4D02-BFEF-182061AC6F8E
Encryption Status: Unlocked
Encryption Type: AES-XTS
Conversion Status: Complete
Conversion Direction: -none-
Has Encrypted Extents: Yes
Fully Secure: Yes
Passphrase Required: Yes
|
+-> Logical Volume 7A998EAE-68FB-4BAC-BF40-7A31D2806B2C
Disk: disk1
Status: Online
Size (Total): 249779191808 B (249.8 GB)
Conversion Progress: -none-
Revertible: Yes (unlock and decryption required)
LV Name: Macintosh HD
Volume Name: Macintosh HD
Content Hint: Apple_HFS
~ belambert$ mount
/dev/disk1 on / (hfs, local, journaled)
devfs on /dev (devfs, local, nobrowse)
map -hosts on /net (autofs, nosuid, automounted, nobrowse)
map auto_home on /home (autofs, automounted, nobrowse)
localhost:/vB3z604U-dvSpES6320fHq on /Volumes/MobileBackups (mtmfs, nosuid, read-only, nobrowse)
~ belambert$ diskutil info disk2
Device Identifier: disk2
Device Node: /dev/disk2
Part of Whole: disk2
Device / Media Name: WD My Book 111A Media
File System: None
Content (IOContent): GUID_partition_scheme
OS Can Be Installed: No
Media Type: Generic
Protocol: USB
SMART Status: Not Supported
Total Size: 2.0 TB (2000365289472 Bytes) (exactly 3906963456 512-Byte-Units)
Volume Free Space: Not applicable (no file system)
Device Block Size: 512 Bytes
Read-Only Media: No
Read-Only Volume: Not applicable (no file system)
Ejectable: Yes
File System: None
Content (IOContent): GUID_partition_scheme
OS Can Be Installed: No
Media Type: Generic
Protocol: USB
SMART Status: Not Supported
Total Size: 2.0 TB (2000365289472 Bytes) (exactly 3906963456 512-Byte-Units)
Volume Free Space: Not applicable (no file system)
Device Block Size: 512 Bytes
Read-Only Media: No
Read-Only Volume: Not applicable (no file system)
Ejectable: Yes
belambert ttys000 Wed Mar 11 17:34 - 17:39 (00:05)
belambert ttys000 Wed Mar 11 17:33 - 17:34 (00:00)
wtmp begins Sun Mar 8 14:40
~ belambert$ ~ belambert$ diskutil list
-bash: :~: command not found
~ belambert$ /dev/disk0
-bash: /dev/disk0: Permission denied
:~ belambert$ #: TYPE NAME SIZE IDENTIFIER
~ belambert$ 0: GUID_partition_scheme *251.0 GB disk0
-bash: 0:: command not found
:~ belambert$ 1: EFI EFI 209.7 MB disk0s1
-bash: 1:: command not found
~ belambert$ 2: Apple_CoreStorage 250.1 GB disk0s2
-bash: 2:: command not found
~ belambert$ 3: Apple_Boot Recovery HD 650.0 MB disk0s3
-bash: /dev/disk1: Permission denied
~ belambert$ #: TYPE NAME SIZE IDENTIFIER
~ belambert$ 0: Apple_HFS Macintosh HD *249.8 GB disk1
-bash: 0:: command not found
~ belambert$ Logical Volume on disk0s2
-bash: Logical: command not found
~ belambert$ 7A998EAE-68FB-4BAC-BF40-7A31D2806B2C
-bash: 7A998EAE-68FB-4BAC-BF40-7A31D2806B2C: command not found
~ belambert$ Unlocked Encrypted
-bash: Unlocked: command not found
:~ belambert$ /dev/disk2
-bash: /dev/disk2: Permission denied
~ belambert$ #: TYPE NAME SIZE IDENTIFIER
:~ belambert$ 0: GUID_partition_scheme *2.0 TB disk2
-bash: 0:: command not found
~ belambert$ 1: Microsoft Reserved 134.2 MB disk2s1
-bash: 1:: command not found
~ belambert$ ~ belambert$ diskutil cs list
-bash: ~: command not found
~ belambert$ CoreStorage logical volume groups (1 found)
-bash: syntax error near unexpected token `('
~ belambert$ |
-bash: syntax error near unexpected token `|'
~ belambert$ +-- Logical Volume Group 883A56F4-5559-4872-A8DA-960F99655B63
-bash: +--: command not found
~ belambert$ =========================================================
-bash: =========================================================: command not found
~ belambert$ Name: Macintosh HD
-bash: Name:: command not found
~ belambert$
-bash: 3:: command not found
~ belambert$ /dev/disk1
Whole: Yes
Internal: No
OS 9 Drivers: No
Low Level Format: Not supported
:~ belambert$ Last login: Wed Mar 11 19:23:03 on ttys000
~ belambert$ diskutil list
Whole: Yes
Internal: No
OS 9 Drivers: No
Low Level Format: Not supported
~ belambert$ Last login: Wed Mar 11 19:23:03 on ttys000
~ belambert$ diskutil list
Volume Name: Not applicable (no file system)
Mounted: Not applicable (no file system)racergirl,
have you tried resetting your MacBook Pro’s System Management Controller, to see if that makes a difference with the heat? -
Can not select external input for sound
can not select external input for sound
Hey there RoosterMonkey,
It sounds like you have Soundtrack Pro installed but you cannot select your external audio device as an input. I recommend the troubleshooting steps from the article named:
Soundtrack Pro 3: Troubleshooting Basics
http://support.apple.com/kb/ht3659
Update to the latest software versions
From the Apple () menu, choose Software Update and make sure that you have the most recent updates for your versions of Soundtrack Pro 3, QuickTime, Compressor, Pro Application Support, and other important system files. Installing the latest updates ensures that your software has the latest improvements and enhancements.
Note: Be sure the application is in the Applications folder and is named Soundtrack Pro before running Software Update.
Check compatibility and driver versions for third-party devices
If you're using a third-party sound card, MIDI interface, storage system, control surface, or plug-in, check the support area on the manufacturer's website to be sure that you're using the latest version of the relevant driver or other software for your product. For information on troubleshooting possible issues with Audio Unit plug-ins, go to Soundtrack Pro 3: Troubleshooting Audio Unit plug-in issues.
Try a different Multitrack Project or Audio File Project
Sometimes project files can become damaged, causing unexpected behavior in Soundtrack Pro. To create a fresh project, choose File, then New and select Multitrack Project or Audio File. Test to see if the issue is resolved in the new project.
Delete the User Preferences
You can resolve many issues by restoring Soundtrack Pro to its original settings. This will not impact your project files. To reset your Soundtrack Pro user preference settings to their original state:
Quit Soundtrack Pro if it is open.
In the Finder, choose Go > Go to Folder from the menu bar.
Type ~/Library/Preferences in the "Go to the folder" field.
Remove the "com.apple.soundtrackpro.plist" file from the Preferences folder.
In the Finder, choose Go > Go to Folder from the menu.
Type ~/Library/Application Support/Soundtrack Pro in the "Go to the folder" field.
Remove the "EffectsCache.plist" file from the Soundtrack Pro folder.
In the Finder, choose Go > Go to Folder from the menu.
Type ~/Library/Application Support/Soundtrack Pro/Layouts in the "Go to folder" field.
Remove the "Soundtrack Pro.saved.moduleLayout" file from the Layouts folder.
In the Finder, choose Go > Go to Folder from the menu.
Type ~/Library/Caches in the "Go to folder" field.
Remove the "com.apple.audiounits.cache" from the Caches folder.
Remove receipts and reinstall Soundtrack Pro 3 and Compressor
Another approach you might consider is reinstalling Soundtrack Pro and Compressor. To do this effectively, you need to remove the applications and their receipts, then install Soundtrack Pro and use Software Update to install additional updates. Compressor gets installed automatically when you install Soundtrack Pro. You don't have to remove everything that was installed with Soundtrack Pro, so follow the steps below to completely reinstall a fresh copy of Soundtrack Pro. Note: Make sure that you have your installation discs handy before beginning.
In Mac OS X v10.6 Snow Leopard or OS X Lion
Open the Terminal application and enter the following commands one at a time and an administrator password when prompted. Note: The commands are case sensitive.
sudo pkgutil --forget com.apple.pkg.Compressor
sudo pkgutil --forget com.apple.pkg.Qmaster
sudo pkgutil --forget com.apple.pkg.VideoOutSupport
sudo pkgutil --forget com.apple.pkg.PSTSharedA
sudo pkgutil --forget com.apple.pkg.AppleHDVCodec
sudo pkgutil --forget com.apple.pkg.AppleIntermediateCodec
sudo pkgutil --forget com.apple.pkg.DSPPublishing
sudo pkgutil --forget com.apple.pkg.SoundtrackPro
sudo pkgutil --forget com.apple.pkg.Uncompressed422
Then, reinstall Soundtrack Pro and Compressor using the following steps:
Open the Applications folder. Drag the Soundtrack Pro and Compressor applications to the Trash.
Insert your Logic Studio or Final Cut Studio installation disc and install Soundtrack Pro.
When finished installing, choose the Apple () menu, then Software Update to update your software to the latest version.
Open Soundtrack Pro to verify that the issue has been resolved.
Thank you for using Apple Support Communities.
Cheers,
Sterling
Maybe you are looking for
-
Dynamic Data Connection Parameter and Report Parameters
Post Author: despec CA Forum: General Hello to all,I am using a business view that is based on a dynamic data connection of 13 databases, each a different school. When I use the BV is a CXrystal Report (XI), it correctly, of course, uses the "read o
-
Backing up Zen MicroPhoto (8
In reviewing all material that came with my new MicroPhoto (ZMP8GB) as well as reviewing this forum, I haven't found anything dealing with how to do a total backup of the Zen. I'd like to make a copy of the complete image of all my music and playlist
-
Implement alert functionality in CPS
Dear All, Is there any way to send an email in case my job got cancelled or process server is down. I have gone through the documentation provided by Redwood but does not get clear steps to configure. All suggestions/answers are welcome. Thanks in ad
-
PO Determine Price Procedure based on ordering Plant
Hi Experts, Please advice how can we determine 2 pricing procedure for a vendor based on ordering Plant in purchase order? Requirement: Client has central purchase organization (1000) for all plants. Now they are going for India rollout where Import
-
Hey, I'm trying to authorize my new laptop with my iTunes account. How would I go about doing this?