External monitors no longer sleep

I have a Feb 2011 Macbook Pro 15" with the i7 and the AMD Radeon HD 6750M video card..
From the Thunderbolt port I go into a Matrox Dual Head 2 Go adpater, which gives me two DVI outputs to matching Lenovo 22" monitors...
Before the 10.7.2 update, these monitors would sleep fine when I put the computer to sleep or shut it down.....
After the update, the monitors initally appear to sleep, but then they light up with a full screen of a grey-ish white (meaning, the aren't sleeping obviously)
I don't understand what could have changed with the update, and scouring the net I don't see this issue raised by anyone else
Any ideas?

I have found some links with similar problems.
http://forums.macrumors.com/showthread.php?t=1520521
http://www.mac-forums.com/forums/apple-desktops/302184-resetting-rebooting-thunde rbolt-ports.html
http://www.macissues.com/2014/04/17/troubleshooting-imac-target-display-mode/
Thunderbolt Display not detected by iMac 27" 2011
Thunderbolt ports and displays: Frequently asked questions (FAQ) - Apple Support
https://www.ifixit.com/Teardown/Apple+Thunderbolt+Display+Teardown/6525
I will try the first suggestions of resetting the PRAM* and SMC†.
Peter
* Shut down and restart holding down command option p r immediately you hear the Start Up sound, hold down until computer restarts and you hear the Start Up sound for the 2nd time.
† Shut down, remove power cord for at least 15 seconds, plug back in and restart.
Peter

Similar Messages

External Monitor no longer works after 10.5.8 Update

I just downloaded 10.3.8 update and my Fujitsu external monitor no longer works with my Imac 24". The same thing has happened to a friend who has the same iMAC and similar external monitor. Is this Apples way to get us to use Apple products only or is this a big with the update? Any ideas? Thank you.

Hello
Try disconnecting all external peripherals, then shutdown your Mac, pull out all power cord, if it is a portable, take out the battery and leave it as it is for at least 5 minutes... 15 mins best.
Then power back your mac and see if the FW ports are working
Cheers

T400 Win7/64 Advanced Dock -- External Monitor No Longer Comes When Booting

My configuration:
T400 (2767-14U)
Windows 7 64bit
256MB ATI Radeon 3470HD (switchable graphics running in "High Performance")
Advanced Dock (2503)
Lenovo D221 Monitor (using VGA cable)
I used the above configuration without issues for a year.
My problem:
I just replaced my hard drive, clean installed the OS and all applications, and updated all drivers and the BIOS using System Update. Since doing that, my external monitor no longer comes on when I boot my computer in the dock (lid closed). The only way I can get the external monitor to work is to boot my computer first, and then "hot dock" it.
As far as I know, all of my BIOS/Power/Graphics settings are the same as always.
Thanks in advance for any help!
Solved!
Go to Solution.

Maybe the BIOS setting for Default Display got switched back to ThinkPad LCD?
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

External Monitor no longer working after install of 10.4.3

Hi:
I am having some major issues after the last update with my external monitor, Dell 1905FP. I have a PowerBook G4 15in, 1.5 processor. Prior to the update I had no issues utlizing the monitor while closing the clamshell but after the update I was unable to utilize the rotation to portrait view on my monitor, with the clamshell closed. It would work on standard view to close the clamshell and then wake the computer utilizing a USB device or bluetooth keyboard.
I decided to after repairing permissions, disk utility, utilizing a DVI and the Analog cord with adaptor, creating a test user account, resetting PRAM and NVRAM and such to try reapplying the combo updater. This further broke the problem as I was unable to close the clamshell and wake the computer up to utilize the external monitor, even in standard (landscape view). When I do close the clamshell with the external monitor hooked up and then wake the computer with my mouse or keyboard the external monitor does power on and shows a lot of static and such not allowing me to see my desktop, but I can see the mouse cursor.
The external monitor works just fine, so long as I leave the lid open and if it goes to sleep with the clamshell open, it wakes just fine and the monitor works. This problem only occurs when I close the clamshell. I prefer the clamshell closed because it gives me the full screen that I desire in portrait mode due to the great amount of writing I do (it allows me to see a full 1 1/2 pages of text in Word while writing).
Another monkey wrench is that I was able to use another monitor, a 17in CRT and it worked just fine, I could close the clamshell and wake the computer utilizing my mouse as I have always been able to. However, I do not believe the Dell monitor is broken, given it will work with a PC laptop perfectly.
Does anyone have a clue on what this issue could be and a possible fix. I have used my Mac exclusively for a little over a year and I am just learning how to troubleshoot this. My thoughts would be to throw away the preferences in the system and then try hooking up the monitor again (as if it were a new monitor)but I have no idea what preferences to throw away.
Any help is appreciated!
Michelle

I answered this question on my own. I was able to utilize Pacifist and reinstalling the video card drivers and display profiles. Now everything works as it should.

External monitor no longer works after installing iLife '09

Before, the external monitor (Apple Cinema HD display) connected via DVI to Mini-DVI adapter was working fine. However, after installing iLife '09 and restarting, the iMac will no longer detect the external display attached to it. I even tried installing a different (but same model) display but it still will not detect.

I'm not sure how installing an application would cause that to happen. Have you shut down (powered off) the iMac completely, and then restarted, since this problem occurred?
Some display settings are stored in PRAM, so if you have not already, try resetting PRAM
http://support.apple.com/kb/HT1379
If that does not help, you can try disconnecting the iMac from power and reconnecting it, using the reset SMC (power management) procedure.
http://support.apple.com/kb/HT1543
When you reconnect it, initially connect the iMac to a wall outlet, by itself. Leave all peripherals disconnected, except for your USB keyboard/mouse. Make sure it is working properly, then connect only the external display.
If it still does not work, as a test, start up with your Mac OS X installation disc. You are not installing anything, but note if the second display is displaying the background image or not when you are booted from a different system.

External monitor will not sleep using 2012 MacBook Air and HDMI adapter

I am running a HP 27xi (27" display) using the apple thunderbolt to HDMI adapter, and using a HDMI cable.
ISSUE:
I run my 2012 macbook air in "clamshell mode", and solely use the 27" display, which works great. Problem, is when the macbook goes to put the display to sleep, or sleep for the laptop, the display starts to go into power save mode, then flips back on... goes back into power save mode, repeats forever. I called HP, and they said the HDMI signal is not being turned off, hence why the screen keeps going ON, then power save, then repeat. If I shutdown the laptop, then the monitor goes off just fine.
Anyone else ran into an issue with an external monitor NOT going to sleep when plugged into the HDMI adapter? Someone suggusted that I purchase a DVI-D adapter, and use that cable... but that sounds ridiculous. The HDMI adapter should absolutely work.
My temporary fix is to turn off the monitor everytime (if i remember) otherwise the display is in this never ending loop of trying to shut down.
And yes, the Macbook Air is 100% up to date with updates. DRIVING ME CRAZY!!!
Joe

Hello Joe,
I definitely understand your concern regarding your external display not going to sleep and endlessly looping into power save mode when your MacBook Air is asleep.
I found an article with steps to troubleshoot issues with displays. This article is for internal and external displays, so you can skip any steps referring to the internal display. The following steps specifically stands out to me for the situation you are experiencing:
Reset the system
You can reset the Mac's parameter RAM and SMC.
You can find the full article here:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Thank you for using Apple Support Communities.
Best,
Sheila M.

After updating to Lion my external monitor no longer works!

I used a external lcd tv to use split screen on my Macbook Pro. After updating to Lion this week it no longer works. First I thought it was my HDMI adapter but I have replaced it and nothing is still working. I've read that people using more than one problem have been having issues but i just have the one external monitor. Help Please!

I found a discussion thread here which seems to do the trick. Like you I've authorized, de-authorized etc, but renaming the files seemed to be the only thing that worked. Here's the detail:
https://discussions.apple.com/thread/3477094?start=0&tstart=0

10.9.1 external monitor on hdmi sleep issue

Hi,
I have been lately having issues with my HD LG LED monitor that I have connected to my macbook thru HDMI.
The monitor goes to sleep and does not wake up at all. The screen stays blank - even after rebooting the laptop or waking it up.
My open windows in the monitor stay in that workspace and can not be accessed on the laptop screen.
I have seen flickering issues on my monitor in the past but thought they were due to static or some emi.
The monitor was working great with the Mavericks update as well so I am not sure what changed in between
The monitor works fine with my Windows notebook
Any pointers would be great!
Thanks,

Hi madsaw,
Welcome to the Support Communities!
The article below may be give you some additional troubleshooting steps to try for your external monitor.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Cheers,
- Judy

External monitors no longer working after todays update!

MacBookPro4,1 I always use an external monitor. After the updated rebooted the MBP the external screen does not get recognized.
HELP!

I answered this question on my own. I was able to utilize Pacifist and reinstalling the video card drivers and display profiles. Now everything works as it should.

T510 2nd External Monitor No Longer Working

Hey Guys,
Hopefully someone can help me out
Came into work with my T510 and inserted on to my Lenovo docking station type 4338. For over 2 years now I had it working with 2 external monitors and also the built in monitor display from the laptop. Now I can only get the built in monitor and monitor 2 (VGA on the docking station) to display.
It detects the 3rd monitor but when I try to extend to it everything goes black and I have to wait for it to time out or pop the laptop off the station and insert it back on.
If I try choosing just the 2 external monitors and close the laptop lid only monitor 2 displays and monitor 3 disconnects itself automatically.
Monitor 3 is connecting using a Display Port to VGA
I have tried 2 other monitors, same results. I have tried DVI and it makes no difference. I tried 2 different docking stations same results and I even reinstalled Windows 8.1 on the laptop hoping that would resolve the issue but it has not.
I know this can work because I had it working before. And the fact that I cant get 2 externals to display with the laptop screen closed is a telling sign something else is going on.
Thanks for all the help and suggestions hopefully to come!
Solved!
Go to Solution.

I was able to solve the issue.
For some reason my BIOS must have reverted back to just Intels intergrated GPU. I had to boot to BIOS and change the video setting to Optimus, I believe that is what it is called.
Once the change was made Windows 8.1 was able to install the drivers automatically, another reboot and all monitors now work.
Hope this helps someone in the future!

Monitor no longer sleeping after 10.8.2 & Mac Mini EFI update

Hopefully someone can help out here, my new 2012 Mac Mini was running fine without any problems, then when I installed the 10.8.2 update (not the original update that got pulled from the Apple site but the newer version) with the EFI Mac Mini firmware update my monitor won't go to sleep anymore. It used to do this without any problems, but since the update it goes to the screensaver without any problems but when the time comes for the monitor to go into sleep mode the screensaver just stays frozen on the screen until the Mini itself goes to sleep. Anyone else had this problem and managed to solve it? Thanks!

OK, as a further step, I typed pmset -g assertions into Terminal and got this response:
11/04/2013 00:09:15 BST
Assertion status system-wide:
PreventUserIdleDisplaySleep    0
PreventSystemSleep            0
PreventUserIdleSystemSleep    1
ExternalMedia                  0
UserIsActive                  0
ApplePushServiceTask          0
BackgroundTask                1
Listed by owning process:
pid 4975(storeagent): [0x0000000c00000811] 134:51:07 BackgroundTask named: "com.apple.storeagent.UpdateStaging"
pid 164(coreaudiod): [0x0000000100001adf] 01:18:15 NoIdleSleepAssertion named: "com.apple.audio.'AppleHDAEngineOutput:1B,0,1,2:0'.noidlesleep"
Kernel Assertions: 0x0132
* Kernel Assertion ID = 500
Created At = 01/01/1970 01:03:17 GMT+
Modified At = 10/04/2013 18:42:18 BST
Owner ID = 0xffffff80914ab000
Level = 255
Assertions Set = None (4)
* Kernel Assertion ID = 501
Created At = 01/01/1970 01:03:24 GMT+
Modified At = 05/04/2013 00:51:26 BST
Owner ID = 0xffffff8032426000
Level = 0
Assertions Set = None (4)
* Kernel Assertion ID = 502
Created At = 01/01/1970 01:03:25 GMT+
Modified At = 07/04/2013 23:05:42 BST
Owner ID = 0xffffff803244c000
Level = 0
Assertions Set = None (4)
* Kernel Assertion ID = 503
Created At = 01/01/1970 01:03:31 GMT+
Modified At = 10/04/2013 18:27:29 BST
Owner ID = 0xffffff8032403400
Level = 0
Assertions Set = None (32)
* Kernel Assertion ID = 929
Created At = 11/04/2013 00:11:02 BST
Modified At = 01/01/1970 01:00:00 GMT+
Owner ID = 0xffffff8032561900
Level = 255
Assertions Set = None (128)
anyone got any ideas what these processes might be and how to stop them?

External drive no longer sleeping

Just upgraded from Mountain Lion to Mavericks on my Mid 2011 iMac. Prior to the upgrade, whenever the iMac went to sleep, the external drive (G-Technology G-Drive Firewire) went to sleep too. Now, the G-Drive doesn't sleep. Any idea how to fix this?

Send Apple feedback is a joke.
I have spent the last 3 months with their AE's both on the phone and via email. I have ran programs on my iMacs to help them gather information.
The last word I got from them was to switch back to my old OS which I did do on my Mac Mini server. The only reason I got feedback was because I am still under full warranty.
They know, believe me they know about the issue, but you are right about their silence on it.

MacbookPro + External Monitor wake up from sleep

Hey,
If I connect my mbp to external monitor and press sleep and then close the lid, 30% of the cases I cannot wake it up. I have all updates in Mountain Lion.
Any thoughts about it? Software bug?

But still, the sleep issue persists, so it is a more subtle timing issue. I upgraded my MBP with a Corsair 8GB kit ( http://www.corsair.com/us/corsair-mac-memory-8gb-ddr3-sodimm-memory-kit-cmsa8gx3 m2a1333c9.html ) and it indicated it had 9-9-9-24 CAS timing. It has worked flawlessly till now. Note that my Mac is a Late 2011, whose memory runs at 1333 MHz.
As far as I can tell, the 13" Mid 2010 models used 1067 MHz memory with 7-7-7-20 CAS timing: http://www.corsair.com/us/corsair-mac-memory-8gb-dual-channel-ddr3-sodimm-memory -kit-cmsa8gx3m2a106c7.html

Windows 8 Bootcamp Does Not Recognize External Monitor

So, my Bootcamp of Windows 8 does not recognize my external monitor when I try to plug it in. I have read that the startup must recognize the monitor during the boot process. However, I have already done this and my external monitor remains in sleep mode. My drivers are all up to date with this bootcamp and I work on programming a lot so I need a solution for this issue because going back and forth between windows of the internet and my code is not ideal for me and wastes too much time. The external monitor works when I run my OS X, just not on Windows 8. If anyone could point me in the direction of how to solve this issue, it would be greatfully appreciated.

They're downloadable. But I'm going to create a system restore point in case something happens.
The below discussion had a similar issue but with Windows 7
https://discussions.apple.com/message/12358950#12358950
http://www.nvidia.com/Download/index.aspx?lang=en-us

No Signal to External Monitor

I use KDE and have a HP ProBook 6560b with a dock/port replicator. My problem is that signal to my external monitor doesn't automatically work on login rather it be via VGA or DVI (currently hooked up over DVI). I tinkered around with it and got it to work sometimes but not consistently.
Edit: This also seems to happen in Gnome using Gnome's display config tool.
That aside, my even bigger issue is when I click KRandRTray down in the system tray and change the display settings to what I want, my external monitor goes to sleep and says "no signal." The settings I want are for my laptop's attached LCD panel (LVDS1) to be "Disabled" (since I keep my laptop lid closed in the dock) and I want my externally attached monitor (HDMI2) to be set to 1680x1050 (Auto). The even stranger part of this is I can eventually get this to work if I start it dual monitor, pick my secondary external monitor (HDMI2) and set it's resolution to 1680x1050 (Auto), set primary display to HDMI2, hit apply then go back in and set LVDS1 to "Disabled" and hit apply again.
To add to this, if at any point in time the external monitor goes to "no signal" mode and the settings restore after the countdown, the external monitor will never show signal until I drop out to a console and killall X and it restarts KDM, etc.
I don't have any Xorg.conf (or config files in /etc/X11/xorg.conf.d) that relates to video settings.
The following is my graphics card that is integrated into my Core i5:
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
Also, the xf86-video-intel version:
xf86-video-intel 2.15.0-2
This is the entire Xorg.0.log file up to the no signal situation on the external monitor:
[ 13.026]
X.Org X Server 1.10.4
Release Date: 2011-08-19
[ 13.040] X Protocol Version 11, Revision 0
[ 13.040] Build Operating System: Linux 3.0-ARCH x86_64
[ 13.040] Current Operating System: Linux nathan-cbts 3.0-ARCH #1 SMP PREEMPT Tue Aug 30 08:53:25 CEST 2011 x86_64
[ 13.040] Kernel command line: root=/dev/mapper/vgroot-lvroot ro i915.modeset=1
[ 13.040] Build Date: 17 September 2011 07:42:58AM
[ 13.040]
[ 13.040] Current version of pixman: 0.22.2
[ 13.040] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 13.040] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 13.040] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Oct 5 09:06:26 2011
[ 13.074] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 13.093] (==) No Layout section. Using the first Screen section.
[ 13.093] (==) No screen section available. Using defaults.
[ 13.093] (**) |-->Screen "Default Screen Section" (0)
[ 13.093] (**) | |-->Monitor "<default monitor>"
[ 13.093] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 13.093] (==) Automatically adding devices
[ 13.093] (==) Automatically enabling devices
[ 13.131] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 13.131] Entry deleted from font path.
[ 13.147] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 13.147] Entry deleted from font path.
[ 13.147] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 13.147] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 13.147] Entry deleted from font path.
[ 13.147] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 13.147] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 13.147] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 13.147] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 13.147] (II) Loader magic: 0x7d6160
[ 13.147] (II) Module ABI versions:
[ 13.147] X.Org ANSI C Emulation: 0.4
[ 13.147] X.Org Video Driver: 10.0
[ 13.147] X.Org XInput driver : 12.2
[ 13.147] X.Org Server Extension : 5.0
[ 13.148] (--) PCI:*(0:0:2:0) 8086:0116:103c:1619 rev 9, Mem @ 0xd4000000/4194304, 0xc0000000/268435456, I/O @ 0x00004000/64
[ 13.148] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 13.148] (II) LoadModule: "extmod"
[ 13.149] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 13.155] (II) Module extmod: vendor="X.Org Foundation"
[ 13.155] compiled for 1.10.4, module version = 1.0.0
[ 13.155] Module class: X.Org Server Extension
[ 13.155] ABI class: X.Org Server Extension, version 5.0
[ 13.155] (II) Loading extension MIT-SCREEN-SAVER
[ 13.155] (II) Loading extension XFree86-VidModeExtension
[ 13.155] (II) Loading extension XFree86-DGA
[ 13.155] (II) Loading extension DPMS
[ 13.155] (II) Loading extension XVideo
[ 13.155] (II) Loading extension XVideo-MotionCompensation
[ 13.155] (II) Loading extension X-Resource
[ 13.155] (II) LoadModule: "dbe"
[ 13.155] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 13.156] (II) Module dbe: vendor="X.Org Foundation"
[ 13.156] compiled for 1.10.4, module version = 1.0.0
[ 13.156] Module class: X.Org Server Extension
[ 13.156] ABI class: X.Org Server Extension, version 5.0
[ 13.156] (II) Loading extension DOUBLE-BUFFER
[ 13.156] (II) LoadModule: "glx"
[ 13.156] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 13.160] (II) Module glx: vendor="X.Org Foundation"
[ 13.160] compiled for 1.10.4, module version = 1.0.0
[ 13.160] ABI class: X.Org Server Extension, version 5.0
[ 13.160] (==) AIGLX enabled
[ 13.160] (II) Loading extension GLX
[ 13.160] (II) LoadModule: "record"
[ 13.161] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 13.161] (II) Module record: vendor="X.Org Foundation"
[ 13.161] compiled for 1.10.4, module version = 1.13.0
[ 13.161] Module class: X.Org Server Extension
[ 13.161] ABI class: X.Org Server Extension, version 5.0
[ 13.161] (II) Loading extension RECORD
[ 13.161] (II) LoadModule: "dri"
[ 13.161] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 13.172] (II) Module dri: vendor="X.Org Foundation"
[ 13.172] compiled for 1.10.4, module version = 1.0.0
[ 13.172] ABI class: X.Org Server Extension, version 5.0
[ 13.172] (II) Loading extension XFree86-DRI
[ 13.172] (II) LoadModule: "dri2"
[ 13.172] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 13.172] (II) Module dri2: vendor="X.Org Foundation"
[ 13.172] compiled for 1.10.4, module version = 1.2.0
[ 13.172] ABI class: X.Org Server Extension, version 5.0
[ 13.172] (II) Loading extension DRI2
[ 13.172] (==) Matched intel as autoconfigured driver 0
[ 13.172] (==) Matched vesa as autoconfigured driver 1
[ 13.172] (==) Matched fbdev as autoconfigured driver 2
[ 13.172] (==) Assigned the driver to the xf86ConfigLayout
[ 13.172] (II) LoadModule: "intel"
[ 13.177] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 13.187] (II) Module intel: vendor="X.Org Foundation"
[ 13.187] compiled for 1.10.2, module version = 2.15.0
[ 13.187] Module class: X.Org Video Driver
[ 13.187] ABI class: X.Org Video Driver, version 10.0
[ 13.187] (II) LoadModule: "vesa"
[ 13.187] (WW) Warning, couldn't open module vesa
[ 13.187] (II) UnloadModule: "vesa"
[ 13.187] (II) Unloading vesa
[ 13.187] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 13.187] (II) LoadModule: "fbdev"
[ 13.187] (WW) Warning, couldn't open module fbdev
[ 13.187] (II) UnloadModule: "fbdev"
[ 13.187] (II) Unloading fbdev
[ 13.187] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 13.187] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server
[ 13.187] (++) using VT number 7
[ 13.197] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 13.198] drmOpenDevice: node name is /dev/dri/card0
[ 13.198] drmOpenDevice: open result is 8, (OK)
[ 13.198] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 13.198] drmOpenDevice: node name is /dev/dri/card0
[ 13.198] drmOpenDevice: open result is 8, (OK)
[ 13.198] drmOpenByBusid: drmOpenMinor returns 8
[ 13.198] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 13.198] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 13.198] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 13.198] (==) intel(0): RGB weight 888
[ 13.198] (==) intel(0): Default visual is TrueColor
[ 13.198] (II) intel(0): Integrated Graphics Chipset: Intel(R) Sandybridge Mobile (GT2)
[ 13.198] (--) intel(0): Chipset: "Sandybridge Mobile (GT2)"
[ 13.198] (**) intel(0): Relaxed fencing enabled
[ 13.198] (**) intel(0): Framebuffer tiled
[ 13.198] (**) intel(0): Pixmaps tiled
[ 13.198] (**) intel(0): 3D buffers tiled
[ 13.198] (**) intel(0): SwapBuffers wait enabled
[ 13.198] (==) intel(0): video overlay key set to 0x101fe
[ 13.208] (II) intel(0): Output LVDS1 has no monitor section
[ 13.208] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
[ 13.208] (II) intel(0): Output VGA1 has no monitor section
[ 13.231] (II) intel(0): Output HDMI1 has no monitor section
[ 13.270] (II) intel(0): Output DP1 has no monitor section
[ 13.395] (II) intel(0): Output HDMI2 has no monitor section
[ 13.418] (II) intel(0): Output HDMI3 has no monitor section
[ 13.456] (II) intel(0): Output DP2 has no monitor section
[ 13.496] (II) intel(0): Output DP3 has no monitor section
[ 13.496] (II) intel(0): EDID for output LVDS1
[ 13.496] (II) intel(0): Manufacturer: SEC Model: 4351 Serial#: 0
[ 13.496] (II) intel(0): Year: 2008 Week: 0
[ 13.496] (II) intel(0): EDID Version: 1.3
[ 13.496] (II) intel(0): Digital Display Input
[ 13.496] (II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 19
[ 13.496] (II) intel(0): Gamma: 2.20
[ 13.496] (II) intel(0): No DPMS capabilities specified
[ 13.496] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 13.496] (II) intel(0): First detailed timing is preferred mode
[ 13.496] (II) intel(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
[ 13.496] (II) intel(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
[ 13.496] (II) intel(0): Manufacturer's mask: 0
[ 13.497] (II) intel(0): Supported detailed timing:
[ 13.497] (II) intel(0): clock: 69.3 MHz Image Size: 344 x 194 mm
[ 13.497] (II) intel(0): h_active: 1366 h_sync: 1414 h_sync_end 1446 h_blank_end 1480 h_border: 0
[ 13.497] (II) intel(0): v_active: 768 v_sync: 770 v_sync_end 775 v_blanking: 780 v_border: 0
[ 13.497] (II) intel(0): Unknown vendor-specific block f
[ 13.497] (II) intel(0): SAMSUNG
[ 13.497] (II) intel(0): 156AT05-307
[ 13.497] (II) intel(0): EDID (in hex):
[ 13.497] (II) intel(0): 00ffffffffffff004ca3514300000000
[ 13.497] (II) intel(0): 00120103802213780a87f594574f8c27
[ 13.497] (II) intel(0): 27505400000001010101010101010101
[ 13.497] (II) intel(0): 010101010101121b567250000c303020
[ 13.497] (II) intel(0): 250058c2100000190000000f00000000
[ 13.497] (II) intel(0): 00000000001eb4027400000000fe0053
[ 13.497] (II) intel(0): 414d53554e470a2020202020000000fe
[ 13.497] (II) intel(0): 00313536415430352d3330370a200017
[ 13.497] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 13.497] (II) intel(0): Printing DDC gathered Modelines:
[ 13.497] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 13.497] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 13.497] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 13.497] (II) intel(0): Printing probed modes for output LVDS1
[ 13.497] (II) intel(0): Modeline "1366x768"x60.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 13.497] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 13.497] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 13.497] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 13.497] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 13.497] (II) intel(0): EDID for output VGA1
[ 13.521] (II) intel(0): EDID for output HDMI1
[ 13.560] (II) intel(0): EDID for output DP1
[ 13.685] (II) intel(0): EDID for output HDMI2
[ 13.685] (II) intel(0): Manufacturer: HWP Model: 2848 Serial#: 16843009
[ 13.685] (II) intel(0): Year: 2011 Week: 24
[ 13.685] (II) intel(0): EDID Version: 1.3
[ 13.685] (II) intel(0): Digital Display Input
[ 13.685] (II) intel(0): Max Image Size [cm]: horiz.: 47 vert.: 30
[ 13.685] (II) intel(0): Gamma: 2.20
[ 13.685] (II) intel(0): DPMS capabilities: StandBy Suspend Off
[ 13.685] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 13.685] (II) intel(0): Default color space is primary color space
[ 13.685] (II) intel(0): First detailed timing is preferred mode
[ 13.685] (II) intel(0): redX: 0.641 redY: 0.335 greenX: 0.298 greenY: 0.611
[ 13.685] (II) intel(0): blueX: 0.147 blueY: 0.070 whiteX: 0.313 whiteY: 0.329
[ 13.685] (II) intel(0): Supported established timings:
[ 13.685] (II) intel(0): 720x400@70Hz
[ 13.685] (II) intel(0): 640x480@60Hz
[ 13.685] (II) intel(0): 800x600@60Hz
[ 13.685] (II) intel(0): 1024x768@60Hz
[ 13.685] (II) intel(0): Manufacturer's mask: 0
[ 13.685] (II) intel(0): Supported standard timings:
[ 13.685] (II) intel(0): #0: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 13.685] (II) intel(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 13.685] (II) intel(0): #2: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 13.685] (II) intel(0): #3: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 13.685] (II) intel(0): #4: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 13.685] (II) intel(0): Supported detailed timing:
[ 13.685] (II) intel(0): clock: 146.2 MHz Image Size: 473 x 296 mm
[ 13.685] (II) intel(0): h_active: 1680 h_sync: 1784 h_sync_end 1960 h_blank_end 2240 h_border: 0
[ 13.685] (II) intel(0): v_active: 1050 v_sync: 1053 v_sync_end 1059 v_blanking: 1089 v_border: 0
[ 13.685] (II) intel(0): Ranges: V min: 50 V max: 76 Hz, H min: 24 H max: 83 kHz, PixClock max 175 MHz
[ 13.685] (II) intel(0): Monitor name: LA2205
[ 13.685] (II) intel(0): Serial No: 3CQ124N20C
[ 13.685] (II) intel(0): EDID (in hex):
[ 13.685] (II) intel(0): 00ffffffffffff0022f0482801010101
[ 13.685] (II) intel(0): 18150103802f1e78ee36c5a4554c9c25
[ 13.685] (II) intel(0): 125054a10800814081809500a940b300
[ 13.685] (II) intel(0): 01010101010121399030621a274068b0
[ 13.685] (II) intel(0): 3600d9281100001c000000fd00324c18
[ 13.685] (II) intel(0): 5311000a202020202020000000fc004c
[ 13.685] (II) intel(0): 41323230350a202020202020000000ff
[ 13.685] (II) intel(0): 003343513132344e3230430a202000d3
[ 13.685] (II) intel(0): Printing probed modes for output HDMI2
[ 13.685] (II) intel(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 13.685] (II) intel(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 13.685] (II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 13.685] (II) intel(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
[ 13.685] (II) intel(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 13.685] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 13.685] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 13.685] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 13.685] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 13.709] (II) intel(0): EDID for output HDMI3
[ 13.746] (II) intel(0): EDID for output DP2
[ 13.786] (II) intel(0): EDID for output DP3
[ 13.786] (II) intel(0): Output LVDS1 connected
[ 13.786] (II) intel(0): Output VGA1 disconnected
[ 13.786] (II) intel(0): Output HDMI1 disconnected
[ 13.786] (II) intel(0): Output DP1 disconnected
[ 13.786] (II) intel(0): Output HDMI2 connected
[ 13.786] (II) intel(0): Output HDMI3 disconnected
[ 13.786] (II) intel(0): Output DP2 disconnected
[ 13.786] (II) intel(0): Output DP3 disconnected
[ 13.786] (II) intel(0): Using fuzzy aspect match for initial modes
[ 13.786] (II) intel(0): Output LVDS1 using initial mode 1024x768
[ 13.786] (II) intel(0): Output HDMI2 using initial mode 1024x768
[ 13.786] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 13.786] (II) intel(0): Kernel page flipping support detected, enabling
[ 13.786] (**) intel(0): Display dimensions: (340, 190) mm
[ 13.786] (**) intel(0): DPI set to (76, 102)
[ 13.786] (II) Loading sub module "fb"
[ 13.786] (II) LoadModule: "fb"
[ 13.787] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 13.802] (II) Module fb: vendor="X.Org Foundation"
[ 13.802] compiled for 1.10.4, module version = 1.0.0
[ 13.802] ABI class: X.Org ANSI C Emulation, version 0.4
[ 13.802] (II) Loading sub module "dri2"
[ 13.802] (II) LoadModule: "dri2"
[ 13.802] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 13.802] (II) Module dri2: vendor="X.Org Foundation"
[ 13.802] compiled for 1.10.4, module version = 1.2.0
[ 13.802] ABI class: X.Org Server Extension, version 5.0
[ 13.802] (==) Depth 24 pixmap format is 32 bpp
[ 13.802] (II) intel(0): [DRI2] Setup complete
[ 13.802] (II) intel(0): [DRI2] DRI driver: i965
[ 13.802] (II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled
[ 13.805] (II) UXA(0): Driver registered support for the following operations:
[ 13.805] (II) solid
[ 13.805] (II) copy
[ 13.805] (II) composite (RENDER acceleration)
[ 13.805] (II) put_image
[ 13.805] (II) get_image
[ 13.805] (==) intel(0): Backing store disabled
[ 13.805] (==) intel(0): Silken mouse enabled
[ 13.805] (II) intel(0): Initializing HW Cursor
[ 14.399] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 14.400] (==) intel(0): DPMS enabled
[ 14.400] (==) intel(0): Intel XvMC decoder enabled
[ 14.400] (II) intel(0): Set up textured video
[ 14.400] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 14.400] (II) intel(0): direct rendering: DRI2 Enabled
[ 14.400] (==) intel(0): hotplug detection: "enabled"
[ 14.400] (--) RandR disabled
[ 14.400] (II) Initializing built-in extension Generic Event Extension
[ 14.400] (II) Initializing built-in extension SHAPE
[ 14.400] (II) Initializing built-in extension MIT-SHM
[ 14.400] (II) Initializing built-in extension XInputExtension
[ 14.400] (II) Initializing built-in extension XTEST
[ 14.400] (II) Initializing built-in extension BIG-REQUESTS
[ 14.400] (II) Initializing built-in extension SYNC
[ 14.400] (II) Initializing built-in extension XKEYBOARD
[ 14.400] (II) Initializing built-in extension XC-MISC
[ 14.400] (II) Initializing built-in extension SECURITY
[ 14.400] (II) Initializing built-in extension XINERAMA
[ 14.400] (II) Initializing built-in extension XFIXES
[ 14.400] (II) Initializing built-in extension RENDER
[ 14.400] (II) Initializing built-in extension RANDR
[ 14.400] (II) Initializing built-in extension COMPOSITE
[ 14.400] (II) Initializing built-in extension DAMAGE
[ 14.498] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 14.498] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 14.498] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 14.498] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 14.498] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 14.498] (II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/i965_dri.so
[ 14.498] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 14.498] (II) intel(0): Setting screen physical size to 270 x 203
[ 14.799] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 14.799] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 14.799] (II) LoadModule: "evdev"
[ 14.800] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.811] (II) Module evdev: vendor="X.Org Foundation"
[ 14.811] compiled for 1.10.0, module version = 2.6.0
[ 14.811] Module class: X.Org XInput Driver
[ 14.811] ABI class: X.Org XInput driver, version 12.2
[ 14.811] (II) Using input driver 'evdev' for 'Power Button'
[ 14.811] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.811] (**) Power Button: always reports core events
[ 14.811] (**) Power Button: Device: "/dev/input/event3"
[ 14.811] (--) Power Button: Found keys
[ 14.811] (II) Power Button: Configuring as keyboard
[ 14.811] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[ 14.811] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 14.811] (**) Option "xkb_rules" "evdev"
[ 14.811] (**) Option "xkb_model" "evdev"
[ 14.811] (**) Option "xkb_layout" "us"
[ 14.829] (II) config/udev: Adding input device Video Bus (/dev/input/event4)
[ 14.829] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 14.829] (II) Using input driver 'evdev' for 'Video Bus'
[ 14.829] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.829] (**) Video Bus: always reports core events
[ 14.829] (**) Video Bus: Device: "/dev/input/event4"
[ 14.829] (--) Video Bus: Found keys
[ 14.829] (II) Video Bus: Configuring as keyboard
[ 14.829] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input4/event4"
[ 14.829] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[ 14.829] (**) Option "xkb_rules" "evdev"
[ 14.829] (**) Option "xkb_model" "evdev"
[ 14.829] (**) Option "xkb_layout" "us"
[ 14.832] (II) config/udev: Adding input device Lid Switch (/dev/input/event2)
[ 14.832] (II) No input driver/identifier specified (ignoring)
[ 14.833] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[ 14.833] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 14.833] (II) Using input driver 'evdev' for 'Sleep Button'
[ 14.833] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.833] (**) Sleep Button: always reports core events
[ 14.833] (**) Sleep Button: Device: "/dev/input/event1"
[ 14.833] (--) Sleep Button: Found keys
[ 14.833] (II) Sleep Button: Configuring as keyboard
[ 14.833] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1/event1"
[ 14.833] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
[ 14.833] (**) Option "xkb_rules" "evdev"
[ 14.833] (**) Option "xkb_model" "evdev"
[ 14.833] (**) Option "xkb_layout" "us"
[ 14.835] (II) config/udev: Adding input device CHICONY HP Basic USB Keyboard (/dev/input/event5)
[ 14.835] (**) CHICONY HP Basic USB Keyboard: Applying InputClass "evdev keyboard catchall"
[ 14.835] (II) Using input driver 'evdev' for 'CHICONY HP Basic USB Keyboard'
[ 14.835] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.835] (**) CHICONY HP Basic USB Keyboard: always reports core events
[ 14.835] (**) CHICONY HP Basic USB Keyboard: Device: "/dev/input/event5"
[ 14.835] (--) CHICONY HP Basic USB Keyboard: Found keys
[ 14.835] (II) CHICONY HP Basic USB Keyboard: Configuring as keyboard
[ 14.835] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4.3/1-1.4.3.1/1-1.4.3.1:1.0/input/input5/event5"
[ 14.835] (II) XINPUT: Adding extended input device "CHICONY HP Basic USB Keyboard" (type: KEYBOARD)
[ 14.835] (**) Option "xkb_rules" "evdev"
[ 14.835] (**) Option "xkb_model" "evdev"
[ 14.835] (**) Option "xkb_layout" "us"
[ 14.836] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event6)
[ 14.836] (**) Logitech USB Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 14.836] (II) Using input driver 'evdev' for 'Logitech USB Optical Mouse'
[ 14.836] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.836] (**) Logitech USB Optical Mouse: always reports core events
[ 14.836] (**) Logitech USB Optical Mouse: Device: "/dev/input/event6"
[ 14.836] (--) Logitech USB Optical Mouse: Found 3 mouse buttons
[ 14.836] (--) Logitech USB Optical Mouse: Found scroll wheel(s)
[ 14.836] (--) Logitech USB Optical Mouse: Found relative axes
[ 14.836] (--) Logitech USB Optical Mouse: Found x and y relative axes
[ 14.836] (II) Logitech USB Optical Mouse: Configuring as mouse
[ 14.836] (II) Logitech USB Optical Mouse: Adding scrollwheel support
[ 14.836] (**) Logitech USB Optical Mouse: YAxisMapping: buttons 4 and 5
[ 14.836] (**) Logitech USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 14.836] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4.3/1-1.4.3.2/1-1.4.3.2:1.0/input/input6/event6"
[ 14.836] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE)
[ 14.836] (II) Logitech USB Optical Mouse: initialized for relative axes.
[ 14.836] (**) Logitech USB Optical Mouse: (accel) keeping acceleration scheme 1
[ 14.836] (**) Logitech USB Optical Mouse: (accel) acceleration profile 0
[ 14.836] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
[ 14.836] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
[ 14.837] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
[ 14.837] (II) No input driver/identifier specified (ignoring)
[ 14.837] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event12)
[ 14.837] (II) No input driver/identifier specified (ignoring)
[ 14.837] (II) config/udev: Adding input device HDA Intel PCH Line In at Sep Rear Jack (/dev/input/event13)
[ 14.837] (II) No input driver/identifier specified (ignoring)
[ 14.838] (II) config/udev: Adding input device HDA Intel PCH Mic at Ext Right Jack (/dev/input/event14)
[ 14.838] (II) No input driver/identifier specified (ignoring)
[ 14.838] (II) config/udev: Adding input device HDA Intel PCH Line Out at Sep Rear Jack (/dev/input/event15)
[ 14.838] (II) No input driver/identifier specified (ignoring)
[ 14.838] (II) config/udev: Adding input device HDA Intel PCH HP Out at Ext Right Jack (/dev/input/event16)
[ 14.838] (II) No input driver/identifier specified (ignoring)
[ 14.838] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP (/dev/input/event17)
[ 14.838] (II) No input driver/identifier specified (ignoring)
[ 14.838] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP (/dev/input/event18)
[ 14.838] (II) No input driver/identifier specified (ignoring)
[ 14.839] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP (/dev/input/event19)
[ 14.839] (II) No input driver/identifier specified (ignoring)
[ 14.840] (II) config/udev: Adding input device HP HD Webcam [Fixed] (/dev/input/event10)
[ 14.840] (**) HP HD Webcam [Fixed]: Applying InputClass "evdev keyboard catchall"
[ 14.840] (II) Using input driver 'evdev' for 'HP HD Webcam [Fixed]'
[ 14.840] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.840] (**) HP HD Webcam [Fixed]: always reports core events
[ 14.840] (**) HP HD Webcam [Fixed]: Device: "/dev/input/event10"
[ 14.840] (--) HP HD Webcam [Fixed]: Found keys
[ 14.840] (II) HP HD Webcam [Fixed]: Configuring as keyboard
[ 14.840] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input10/event10"
[ 14.840] (II) XINPUT: Adding extended input device "HP HD Webcam [Fixed]" (type: KEYBOARD)
[ 14.840] (**) Option "xkb_rules" "evdev"
[ 14.840] (**) Option "xkb_model" "evdev"
[ 14.840] (**) Option "xkb_layout" "us"
[ 14.843] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 14.843] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 14.843] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 14.843] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 14.843] (**) AT Translated Set 2 keyboard: always reports core events
[ 14.843] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 14.843] (--) AT Translated Set 2 keyboard: Found keys
[ 14.843] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[ 14.843] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 14.843] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
[ 14.843] (**) Option "xkb_rules" "evdev"
[ 14.843] (**) Option "xkb_model" "evdev"
[ 14.843] (**) Option "xkb_layout" "us"
[ 14.843] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event11)
[ 14.843] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 14.843] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 14.843] (II) LoadModule: "synaptics"
[ 14.843] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 14.850] (II) Module synaptics: vendor="X.Org Foundation"
[ 14.850] compiled for 1.10.2, module version = 1.4.1
[ 14.850] Module class: X.Org XInput Driver
[ 14.850] ABI class: X.Org XInput driver, version 12.2
[ 14.850] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 14.850] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 14.850] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 14.850] (**) Option "Device" "/dev/input/event11"
[ 14.970] (--) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5690
[ 14.970] (--) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4854
[ 14.970] (--) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 14.970] (--) SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 14.970] (--) SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 14.970] (**) Option "TapButton1" "1"
[ 14.970] (**) Option "TapButton2" "2"
[ 14.970] (**) Option "TapButton3" "3"
[ 15.076] (--) SynPS/2 Synaptics TouchPad: touchpad found
[ 15.076] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 15.183] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio4/input/input11/event11"
[ 15.183] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
[ 15.183] (**) SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 15.183] (**) SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[ 15.183] (**) SynPS/2 Synaptics TouchPad: AccelFactor is now 0.037
[ 15.183] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 15.183] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 15.183] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 15.183] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 15.183] (--) SynPS/2 Synaptics TouchPad: touchpad found
[ 15.183] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[ 15.183] (II) No input driver/identifier specified (ignoring)
[ 15.184] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/event7)
[ 15.184] (II) No input driver/identifier specified (ignoring)
[ 15.184] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/js0)
[ 15.184] (II) No input driver/identifier specified (ignoring)
[ 15.184] (II) config/udev: Adding input device PC Speaker (/dev/input/event8)
[ 15.184] (II) No input driver/identifier specified (ignoring)
[ 15.186] (II) config/udev: Adding input device HP WMI hotkeys (/dev/input/event9)
[ 15.186] (**) HP WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 15.186] (II) Using input driver 'evdev' for 'HP WMI hotkeys'
[ 15.186] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 15.186] (**) HP WMI hotkeys: always reports core events
[ 15.186] (**) HP WMI hotkeys: Device: "/dev/input/event9"
[ 15.186] (--) HP WMI hotkeys: Found keys
[ 15.186] (II) HP WMI hotkeys: Configuring as keyboard
[ 15.186] (**) Option "config_info" "udev:/sys/devices/virtual/input/input9/event9"
[ 15.186] (II) XINPUT: Adding extended input device "HP WMI hotkeys" (type: KEYBOARD)
[ 15.186] (**) Option "xkb_rules" "evdev"
[ 15.186] (**) Option "xkb_model" "evdev"
[ 15.186] (**) Option "xkb_layout" "us"
[ 39.891] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 39.891] (II) intel(0): Printing DDC gathered Modelines:
[ 39.891] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 52.300] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 52.300] (II) intel(0): Printing DDC gathered Modelines:
[ 52.300] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 52.625] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 52.625] (II) intel(0): Printing DDC gathered Modelines:
[ 52.625] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 54.852] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 54.852] (II) intel(0): Printing DDC gathered Modelines:
[ 54.861] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 70.112] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 70.113] (II) intel(0): Printing DDC gathered Modelines:
[ 70.113] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 72.893] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 72.893] (II) intel(0): Printing DDC gathered Modelines:
[ 72.893] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 82.662] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 82.662] (II) intel(0): Printing DDC gathered Modelines:
[ 82.662] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 82.951] (II) intel(0): Allocated new frame buffer 1088x770 stride 4608, tiled
[ 83.011] (II) intel(0): Allocated new frame buffer 1728x1052 stride 7168, tiled
[ 83.497] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 83.497] (II) intel(0): Using hsync ranges from config file
[ 83.497] (II) intel(0): Using vrefresh ranges from config file
[ 83.497] (II) intel(0): Printing DDC gathered Modelines:
[ 83.497] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 83.497] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 83.497] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 83.497] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 83.497] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 83.497] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 83.497] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 83.497] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 83.498] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 83.498] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 83.787] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 83.787] (II) intel(0): Using hsync ranges from config file
[ 83.787] (II) intel(0): Using vrefresh ranges from config file
[ 83.787] (II) intel(0): Printing DDC gathered Modelines:
[ 83.787] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 83.787] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 83.787] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 83.787] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 83.787] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 83.787] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 83.787] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 83.787] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 83.788] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 83.788] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 84.094] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 84.094] (II) intel(0): Using hsync ranges from config file
[ 84.094] (II) intel(0): Using vrefresh ranges from config file
[ 84.094] (II) intel(0): Printing DDC gathered Modelines:
[ 84.094] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 84.094] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 84.094] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 84.094] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 84.094] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 84.094] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 84.094] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 84.094] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 84.094] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 84.094] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 84.219] (II) intel(0): Allocated new frame buffer 1728x1050 stride 7168, tiled
[ 84.276] (EE) intel(0): failed to set mode: Invalid argument
[ 84.467] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 84.467] (II) intel(0): Using hsync ranges from config file
[ 84.467] (II) intel(0): Using vrefresh ranges from config file
[ 84.467] (II) intel(0): Printing DDC gathered Modelines:
[ 84.467] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 84.467] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 84.467] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 84.467] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 84.467] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 84.467] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 84.467] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 84.467] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 84.467] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 84.467] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 84.807] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 84.807] (II) intel(0): Using hsync ranges from config file
[ 84.807] (II) intel(0): Using vrefresh ranges from config file
[ 84.807] (II) intel(0): Printing DDC gathered Modelines:
[ 84.807] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 84.807] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 84.807] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 84.807] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 84.807] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 84.807] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 84.807] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 84.807] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 84.808] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 84.808] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 85.104] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 85.104] (II) intel(0): Using hsync ranges from config file
[ 85.104] (II) intel(0): Using vrefresh ranges from config file
[ 85.104] (II) intel(0): Printing DDC gathered Modelines:
[ 85.104] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 85.104] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 85.104] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 85.104] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 85.104] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 85.104] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 85.104] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 85.104] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 85.104] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 85.104] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 85.447] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 85.447] (II) intel(0): Using hsync ranges from config file
[ 85.447] (II) intel(0): Using vrefresh ranges from config file
[ 85.447] (II) intel(0): Printing DDC gathered Modelines:
[ 85.447] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 85.447] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 85.447] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 85.447] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 85.447] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 85.447] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 85.447] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 85.447] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 85.447] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 85.447] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 85.791] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 85.791] (II) intel(0): Using hsync ranges from config file
[ 85.791] (II) intel(0): Using vrefresh ranges from config file
[ 85.791] (II) intel(0): Printing DDC gathered Modelines:
[ 85.791] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 85.791] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 85.791] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 85.791] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 85.791] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 85.791] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 85.791] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 85.791] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 85.791] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 85.791] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 86.169] (WW) intel(0): flip queue failed: Device or resource busy
[ 86.169] (WW) intel(0): Page flip failed: Device or resource busy
[ 86.313] (WW) intel(0): flip queue failed: Device or resource busy
[ 86.313] (WW) intel(0): Page flip failed: Device or resource busy
[ 100.047] (II) intel(0): EDID vendor "HWP", prod id 10312
[ 100.047] (II) intel(0): Using hsync ranges from config file
[ 100.047] (II) intel(0): Using vrefresh ranges from config file
[ 100.047] (II) intel(0): Printing DDC gathered Modelines:
[ 100.047] (II) intel(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 100.047] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 100.047] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 100.047] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 100.047] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 100.047] (II) intel(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 100.047] (II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 100.047] (II) intel(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 100.047] (II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 100.047] (II) intel(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 100.156] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 100.156] (II) intel(0): Printing DDC gathered Modelines:
[ 100.156] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 100.464] (WW) intel(0): flip queue failed: Device or resource busy
[ 100.464] (WW) intel(0): Page flip failed: Device or resource busy
[ 100.472] (II) intel(0): Allocated new frame buffer 1728x1050 stride 7168, tiled
[ 100.790] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 100.790] (II) intel(0): Printing DDC gathered Modelines:
[ 100.790] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 101.081] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 101.081] (II) intel(0): Printing DDC gathered Modelines:
[ 101.081] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 101.435] (II) intel(0): EDID vendor "SEC", prod id 17233
[ 101.435] (II) intel(0): Printing DDC gathered Modelines:
[ 101.435] (II) intel(0): Modeline "1366x768"x0.0 69.30 1366 1414 1446 1480 768 770 775 780 -hsync -vsync (46.8 kHz)
[ 190.516] (II) AIGLX: Suspending AIGLX clients for VT switch
Since this is a multi-part problem I guess my initial task is to understand why going directly to disabling the laptop's LCD and setting my external monitor to 1680x1050 (Auto) doesn't work without going through the other steps.
Last edited by nnelson123 (2011-10-05 13:48:19)

[ 13.093] (==) No Layout section. Using the first Screen section.
[ 13.093] (==) No screen section available. Using defaults.
[ 13.093] (**) |-->Screen "Default Screen Section" (0)
[ 13.093] (**) | |-->Monitor "<default monitor>"
[ 13.093] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
First step would be to create the necessary entries (easier to make a complete xorg.conf versus xorg.conf.d/##-whatever.conf).
All Desktop Environments / Window Managers rely on X. Man pages are helpful, possibly some headaches ahead as I fought a dual-monitor display this way.
I currently run a xrandr script to switch displays on my hp pavilion: https://wiki.archlinux.org/index.php/Xrandr#Scripts
Check it out.

External monitors no longer sleep

Similar Messages

Maybe you are looking for