Extra fast/ethernet port on 2610 router?

I am looking for a way to add an extra ethernet port on my 2610. What i have read is making me wonder if the only way to do this would be the NM-1E or NM-4E. Are there any other modules or WICs that would give me an fast/ethernet port?
Thanks,
Kyle

Hi,
NM-2FE2W & NM-1FE2W
is one which is supported by the new model 2691. Since 2610 is end of line cisco will not support it.
If possible you can try inserting if you have a spare. May be it would work. Its on your own risk.
Below is the link.
http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet0900aecd800fa5be.html
Hope this helps.
Regards,
Pravin

Similar Messages

  • Connect unmanaged switch to 887VA fast ethernet port

    I tried connecting an unmanaged (and dumb) switch to one of the four fast ethernet ports on the back of the router. I configured the port to act as an access port bound to a specific VLAN, say no. 100.
    What I can see on the LEDs of the unmanaged switch is that the link goes up and down every few seconds. I don't know if this is related to the spanning tree protocol and unfortunately the unmanaged switch doesn't know about STP and doesn't send out BPDUs.
    So, how I should configure the port in order to avoid the link going up and down?
    The actual conf. for the port:
    interface fastEthernet 3
    switchport mode access
    switchport access vlan 100

    What do you mean by dumb siwthc? What model/make/company is that switch?
    Can you try to do the reset of the switch so that it wipe off all the config what so ever present on the box and then try to connect the switch to the router?

  • AEBS 802-11N with fast ethernet ports?

    Hi
    One year (januari 2007) ago I bought the new model of the AEBS 802-11N. I always thought it had 3 Gigabit Ethernet ports. Just now when trying to install the new 7.3.1 firmware, I only can install the Fast Ethernet firmware. It seems that the AEBS only has Fast Ethernet ports instead of Gigabit ports.
    Who can confirm that the AEBS (release jan. 2007) has only Fast Ethernet ports?
    Jurgen

    JurgenS, Welcome to the discussion area!
    Who can confirm that the AEBS (release jan. 2007) has only Fast Ethernet ports?
    Yes that is true.
    The Gigabit version was released in August 2007.

  • ONT: Ethernet port & DGL-4500 router

    Hello everyone,
    Currently I have only FIOS Internet and do not have any plans to get TV service, so this will make the setup substantially more flexible.
    Right now I have my ActionTec configured as a bridge and connected to a Coaxial cable. From the ActionTec, I connect to my DGL-4500. This is my main router. I've had to use the ActionTec as a bridge due to the coaxial cable.
    I would prefer to ditch the ActionTec completely and connect my DGL-4500 directly to the ONT via that Ethernet Port. However, there's 2 problems: First, the ethernet port on the ONT has a bunch of clear goo in it, and it's extremely hard to get out. What the heck is this? Secondly, the light is competely turned off, even after plugging it into my router.
    The light being off, according to my investigation, is deliberate. This is because you cannot have the MocA and the Ethernet enabled simultaneously. If this is true, I would have to get technical support to enable it remotely, right? I always hate having to call verizon, so if this can be avoided that would be ideal.
    The first thing I want to know is if I would benefit by ditching the ActionTec as a bridge and connecting my DGL-4500 router directly. Is there any extra overhead? If the router does no processing and literally acts as a Layer 2 switch, then it shouldn't be too bad. However, I'm worried that it is processing traffic.
    Secondly, how easy is it to get the ethernet port enabled? What would you guys recommend for my setup? 
    Solved!
    Go to Solution.

    Your issue is simple to resolve - You state you are not a video customer - therefore may use your own router - Via pm provide me with your contact information and I can re-provision your ckt to Ethernet.
    ALLEN S.
    NETWORK TECH
    Verizon Telecom
    Fiber Solution Center

  • HP Color LaserJet 3600(not 3600n) with Fast Ethernet port - can I use it?

    Hello! There is a HP Color LaserJet 3600 in our company connected via USB with XP-based PC. Recently I decided that we need this printer be shared directly trough our ethernet network, so I started to learn manuals - its own manual, Jet Direct, and all that stuff. The printer's manual says that HP Color Laserjet 3600 does not have neither its own ethernet port, nor support for embedded print-server like JetDirect 620n.
    But! 
    Visual check  shows that this HP 3600 DOES have its own ethernet port and if I connect it to network or at least to a notebook - it blinks like any other ethernet port with "lights" should do. 
    However.
    Neither front panel, nor back panel says anything about network support(like letter "n" in model name).
    Configuration page print also does not know about that mysterious port.
    So my questions are:
    1. What is this port actually?
    2. Can I use it to share printer over network? Maybe, there is a way to upload 3600n's firmware somehow? 

    The product you have seems to be a commercial printer. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You may find the Commercial Laserjet board here.
    http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
    You can also find the article pertaining to this product here:
    http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesI...
    (contains basic troubleshooting info, manuals, drivers, etc)
    Hope this helps!
    Help the community by marking this post as a solution if it solved your issue!.
    If my post helped you in any way, please click the blue KUDOS star under my name! It would mean a great deal.

  • Anyone help me redundancy for serial in to fast ethernet

    We have connected some customer through leaseline through router serial interface .
    the main problem is sometime the leaseckt is down for 2 or 3 days continously.
    so we want redundancy for those customer.
    we have backup rf link
    so any possiblities are there for if serial interface line protocol went down automatically traffic swithover to ethernet interface of 3550 switch fa interface

    Hi
    in this figure the customer have one ip 16 ip block that is oruted with IGRP in PE router
    we want either link customer use same ip block.
    and in RF link Base Station is connected in L3 Swith Fast Eternet port.
    All rf customers are in different VLANS.
    if the LeaselIne went down the traffic will automatically swithed over to rf link
    means the L3 swith fast ethernet port have several vlan membership in this it automatically go.
    sorry for poor english.
    looking forward u r reply.
    thanks

  • Do I need an ethernet switch or new router for IP camera setup with old Airport Express

    Hello,
    I am trying to setup a third party Foscam IP camera to my network so that I can ultimately use it as a baby monitor, and am having some difficulty.  I currently still have an old Airport Express (with one ethernet port only).  This is preventing me from setting up the initial camera because I don't have another ethernet port to plug it in to on the router.  I am wondering if I can just buy an ethernet switch and have it "split" the ethernet from my modem to both the camera and the Airport (I do need to check with my ISP provider if they give me two separate IP address... but if they do, would this work?). 
    I am fairly sure however, that my ISP provider (comcast) only provides one IP for my account.  Does this mean I would have to buy a new router altogether with more than one ethernet port on it or one with a WAN port?  Would I, in this case, have to plug the modem into the WAN port on the router, and then the camera to one of the ethernet ports on the router?
    I consider myself fairly tech savy, but when it comes to routers, IPs, LAN, WAN, etc. I get a bit lost.  This has been creating quite a headache for me and any help would be appreciated!  Thanks in advance!

    I am wondering if I can just buy an ethernet switch and have it "split" the ethernet from my modem to both the camera and the Airport (I do need to check with my ISP provider if they give me two separate IP address... but if they do, would this work?).
    Sorry, but this won't work as the modem expects only a single device ... either a computer or a router to be connected to it. Unless your modem is actually a combination modem & router or gateway device, then you would need a different router to solve your networking problem.

  • Ethernet port authentication

    Is there a way to create Ethernet port authentication on the router, that would require anyone using the Ethernet ports on the router via an ethernet cable to first be authenticated?

    Is there a way to create Ethernet port authentication on the router
    Sorry, but no on an Apple AirPort Extreme, or Time Capsule if those are the router(s) that you are asking about.

  • WRT-54GL: DSL Modem won't work in Internet port, but works in other ethernet ports. Help?

    To begin, IP addresses for ALL devices on my network are static and manually assigned, no DHCP, in case that matters at all. My problem is that when I plug my DSL modem into the Internet port on the back of my router it doesn't even see the modem and obviously I can't get on the internet. However, I can plug the modem into any of the other Ethernet ports on the router and it sees the modem just fine and I can use the internet. I don't quite understand this. It hasn't caused any problems at all, but I find it strange. This problem has existed with both the stock firmware as well as Tomato firmware. What can I do to get my modem to work through the Internet port instead of the regular ethernet ports? Please take into consideration that I am using the latest Tomato firmware. Thanks all!

    Press the reset button on the router for 30 seconds. The Power light will start flashing. Turn the Router and the Modem OFF. Turn the modem ON first, wait for 10 seconds, turn the router ON, wait for 10 seconds, you should be ONLINE !!!
    C | EH
    linksyshelp.blogspot.com

  • Ethernet port 0/0 on Cisco 2600 unable to access NM-ESW-16 ports

    Is it possible to config the E0/0 port on the Cisco 2600 router to access the FE ports on the on-board NM-ESW-16? There is only one Ethernet port on the router.

    Thanks for the reply. However, we are unclear how to accomplish this. I tried the no switchport mode command on a FE port on the switch. Afterwards, I tried to assign an IP adddress and mask to the port. The switch responded saying that an IP address cannot be applied to a L2 port. What I need to understand is how to re-assign a L2 port as a L3 port. Thanks for any added help.
    kjjscharff

  • Cisco AP 1240AG series Fast Ethernet cannot up

    Hi all :
    My question here is how is the IP configuration for this Fast Ethernet F0.
    This is because usually we only assign IP to the BVI interface. Is it after that, the Fast Ethernet F0 automatically also be assigned the same IP?
    As such, when goto the Fast Ethernet F0 by CLI, by using no shut then this will Enable the Fast Ethernet Port?
    Thanks!
    Best regards,
    tangsuan

    Hi Scott :
    The problem is due to the patch line not connect up somewhere. After connect the line up, now the Optical Ethernet line is up.
    Thanks for your help on this.
    regards,
    tangsuan

  • Linksys X2000 Ethernet port problem

    Hello
    When I connect any cable to the ethernet ports on my router, it automatically disconnects from DSL. I just bought this modem yesterday and cannot get over this problem.
    It works normal when I don't connect anything to ethernet ports.
    I updated the firmware to v 2.0.03 but still no change.

    It is really strange that the performance of the router was affected when there is a device connected to the router’s Ethernet port. If that is the case then there could be something with the settings on your router. By the way, have you installed a PPPoE dialer (Broadband icon) on your computer? If you do, then set that PPPoE dialer to “cancel as default” or might as well disable it. You might also need to start from scratch in order for you to fix this problem and that is by resetting the router. Then use the link below for instructions on how to set the router to PPPoE.
    Setting up a Linksys router for DSL Internet connection

  • How do I add an airport extreme to existing time capsule network and be able to use the router ethernet ports?

    Good day everyone.  I recently upgraded my airport extreme network by replacing the base station with a time capsule router.  Since I now have an "extra" airport extreme router, I've set it up on the other side of the house to both extend the wireless range as well as use it's LAN ports for a home theater system in that location.  Connecting the two routers was done via ethernet.  It now appears that I need to do something "else" as the LAN ports on the now relocated airport extreme are nonfunctional.  All devices are operating well for wireless and as a review, the modem is connected to the time capsule WAN which is connected to the airport extreme via ethernet cable via LAN to it's WAN port.  What do I need to change on configurations to get the LAN ports functioning on the airport extreme?  Thank you for any help.

    Connecting the two routers was done via ethernet.  It now appears that I need to do something "else" as the LAN ports on the now relocated airport extreme are nonfunctional.
    With both base stations interconnected by Ethernet you have the basis for a "roaming" type network. If properly configured, both base stations' Ethernet ports would be enabled for wired clients.
    The key configuration items for a roaming network are as follows:
    All base stations used must be interconnected by Ethernet.
    The "main" base station; the one connected to the Internet modem, must be configured to provide both NAT & DHCP services; all other base stations used must be configured as bridges (NAT & DHCP disabled.)
    Each base station must have a unique base station name.
    Each base station must use the same wireless security type and password.

  • Using ethernet port on range extender: faster??

    I have an extender is the room with this computer for a wireless connection. This extender is v3 with the ethernet connection. Just for fun, I plugged my computer into that connection and disabled my wireless and found that I had a "wired-like" connection. Is there any real advantage to this besides not having to deal with security on this computer? In otherwords, is the wireless communciation between the router and the extender faster than the wireless connection between the extender and a given computer?

    Does the computer get online with ethernet port from range expander? It is only meant for configuring it.

  • Can I activate the ethernet ports (routing) of Time Capsule "joining" an existing non-Apple wireless network ?

    Hello,
    I have a DSL modem that is also a WIFI router as my main WIFI network from room A. In room B, I have a TC wirelessly joining the existing WIFI network (not creating a new one). That works fine, I have one SSID, and I can wirelessly access the TC disks and backup my Mac on my TC.
    Now, I would like to connect a wired device (with on WIFI) to the ethernet port of my TC. Unfortunately, the ethernet ports of the TC don't seem to be "activated" as they do not have internet on them.
    More precisely, I'd like to connect a GE Cordless Skype Phone Model# 31591 (http://www.gephones.com/products/skype/dect-6-0-expandable-digital-cordless-phon e-with-skypetm.html) that connects to a router via Ethernet. I'm aware that I could simply connect it to the DLS router, but that's not what I want... Is there any way to activate the ethernet ports of the TC while in "join" mode ? Or do I really have to buy a Airport Express to create my main network and then extend it ?!?

    Thanks, the reason why I asked again, is because you told me to start another thread with the specifics of the device I want to connect, so I did
    Not a big deal, and it is easy to become confused.....but to be clear about this  
    Your question.....
    is there a way I can connect my Bluray player to the TC ?
    My Answer.....
    Please start a new post for that. Tell us the make and model number of the player and whether you plan to connect using wireless or Ethernet.
    so I tried to creat the main WIFI network with a first-generation Airport Express M9470LL/A (802.11b/g, no "draft N" or "n" support) and the TC wouldn't extend it either, is it too old/not supported
    Unfortunately, the "extend" setup will only work with "n" devices.  The older Express does not have a setting to "Allow this network to be extended", so the Time Capsule cannot pick up the signal.
    I'm not sure what else to suggest other than what I already have.  I'm assuming that you do not want to buy another new Airport Express.

Maybe you are looking for