Extreme Memory Profile & Base Clock - Resolved

Hi,
I am an Eclipse SLI with BIOS v1.4. When I enable the Extreme Memory Profile, the Base Clock option is no longer visable but I do then get a Ratio option. The only was I can oveclock the CPU is to up the Ration from 20 to 21 and then use the Overclocking Centre within Vista.
Is it a case of one or the other? With the XMP enabled, all 12GB of my RAM runs at 1600MHz just fine.
My obejective is to get my CPU to run at 3.2GHz and have my memory running at 1600MHz - is this possible?
System specification as below - Thanks.

Hi,
Thank you for your suggestion. In the end I raised the base clock to 161 and changed the memory ratio to 5. This gave me 3.2GHz for the CPU and all 12GB of my memory runs at 1600MHz.
Just for others who might read this, you need to have both the Extreme Memory Profile and the Advanced XMP options enabled, as if you only have XMP enabled the Base Clock option for the CPU is not visible.
One last thing, the Nocutura CPU cooler is amazing. Even under load using Flight Simulator X with the overclocking, my CPU never exceeded 35 deg C, the IOH 63 deg C and the system 26 deg C.

Similar Messages

MSI Z77A-G43 - extreme memory profile problem

Hello everyone,
I’d really appreciate a piece of help here. I’ve bought the MSI motherboard MSI Z77A-G43 and currently I’m having problems with my memory (slots 1 and 3). My PC has following specs:
-   MSI Z77A-G43
-   Intel Core i5 2500K (not overclocked)
-   RAM Patriot 2x4GB DDR3 1600MHz CL9 (PGD38G1600ELK) G2 Series
Everything is set to default values and works fine. But when I enter the BIOS, I see that the memory is automatically set to 1333 MHz. The memory has the XPM. But when I set the XPM (agressive timing, 1600 MHz) support (no other changes) and reboot the PC, it doesn’t work (endless reboot looping). Is there any way how I can make the XPM modus work? The memory is OK (tried on other MBs, XPM without problems), the CPU too. I tried overclocking, with slightly increased voltage I can easily reach 4,8 GHz on CPU, basically everything else is fine. The PSU is also sufficient (700W, OCZ). I can too set the memory on 1600 MHz manually, but the timing isn’t that good.
It’s actually a failure I can live with, but since it’s a brand new PC, I’d like to get the best out of it.
Many thanks
V.K.

Sometimes manually setting them works when XMP refuses to.
I don't know what the XMP SPD profile for that memory is, and a screenshot of your SPD and memory tabs would help.
However try the following.
Disable XMP and reboot so they are back at 1333.
Manually set it to 1600 and ensure manual setting of the timings to 9.9.9.24 see if that works.
If not set your DRAM voltage to 1,575V and see if that works.
It may be that your memory requires 1,65V, in which case, that is what you have to set. You should be able to see that in CPU-Z SPD tab under the XMP profile column.

Starting memory profile in Library causes LV to crash

Hello!
When I'm working on a library with many classes labview crashes sometimes. Today I was able to trigger the crash manually.... Even on an empty library, if I try to start the memory profiling tool, LV crashes..
#Date: Mi, 23. Jan 2013 10:02:58
#OSName: Windows 7 Enterprise Service Pack 1
#OSVers: 6.1
#OSBuild: 7601
#AppName: LabVIEW
#Version: 12.0f3 32-bit
#AppKind: FDS
#AppModDate: 10/04/2012 15:12 GMT
#LabVIEW Base Address: 0x00400000
<DEBUG_OUTPUT>
23.01.2013 10:03:16.550
Crash 0x0: Crash caught by NIER
File Unknown(0) : Crash 0x0: Crash caught by NIER
minidump id: 381ce9c1-0956-48de-86cf-0ac5f02c36cd
ExceptionCode: 0xC0000005
</DEBUG_OUTPUT>
0x01AF1179 - LabVIEW <unknown> + 0
0x01AF1688 - LabVIEW <unknown> + 0
0x7C37FDB4 - MSVCR71 <unknown> + 0
0x77B574DF - ntdll <unknown> + 0
0x77B19EC5 - ntdll <unknown> + 0
0x00000000 - <unknown> <unknown> + 0
Is it a bug?

Dear Customer,
I could reproduce this crash on LV2012 and also on LV2011.
So it seems to be a Bug and I'm going to write an CAR to R&D so it can be fixed as soon as possible.
Thank you for your cooperation.
Regards,
Oleg Scherling, M.Eng | Applications Engineering | National Instruments | NIG

Memory Profiling OPMN changes

When I add the -agentpath option specified in the JDeveloper document to configure the remote memory profiling in Oracle 10g Application server's opmn.xml I get following error "Unrecognized option -agentpath..." and the server does not start.
Has anyone successfully configured the application server to perform remote profiling?

Thank you, shgoel, you're right.
We replaced the default JDK 1.4 with JDK 1.5 (in the directory D:\Ora10gas\as\jdk\ to be precise)
We moved the profiler DLL to the JDK bin and used the -agentlib option instead of the -agentpath (not sure if this change was significant, though)
To the Java start-parameters in opmn.xml we added the profiling port and a pointer to the profiler-agent.jar.
The resulting Java start parameters where:
-server -Xrs -Xmx512m
-agentlib:profiler15=port=4627,jarpath=D:\jdev\lib\profiler-agent.jar,enable=m
-Dmic.system.home=d:\mic_home
-Dmic.j2ee.home=D:\Ora10gas\as\j2ee\OC4J_MIC\applications\mic
With these settings we where able to connect remotely with JDevelopers memory profiler and resolve a memory leak.
Thanks
Niels Erik

Ever increaing RAM usage of flashPlayer not shown in memory profiler of FlashBuilder

I have a flash application created with Flex in FlashBuilder which uses the Stage3D-API (Away3D-Library is used).
In this flash application 3D-objects are created and added to scene and they are also removed/disposed again, and then they are created/added again.
Performing these scene altering operations the RAM usage of the flashPlayer process (monitored in Windows7-Taskmanager) steadily increases by big amounts (lets say 20MB).
On the other hand the Memory-profiler does not show any such increases at all. Regarding to memory profiler the application still uses bascially the same amount of memory (the line stays flat).
There are some objects marked as loitering, but they donet seem to build-up. And their total amount is (if at all) 0,3MB.
After a while of 3d-scene altering operations (adding, removeing objects) the application/flash-player crashes, most possibly to not being able to allocate more RAM (Taskmanager shows RAM almost completely used up by flashPlayer-process). The application does not exit due to 3d-resource related limits like vertex-buffers, but here are now my questions:
Questions:
a) Are there areas of RAM-usages a (stage-3d) application uses up, which can not be profiled by FlashBuilder?
For exmaple: Is it possible that some objects (maybe stage-3d related) that hold onto some areas of memory/RAM which do not show up in memory profiler?
c) Is the versioning of used components (flashPlayer, FlashBuilder or used Flex-SDK) in an way relevant when memory profiling an application? It it possible that i dont properly see the used memory by my application because i might have old version of involved components?
d) Do you have any other idea what might be the cause here for increased RAM-usage or why it does not show up in memory profiler? I mean at least i expected to see it in memory profiler.
e) Generally i understand that the flashPlayer allocates RAM as it sees fit, and that its not the same amount of memory my application currently uses. But if my application seems not to use/demand any more memory (at least thats what the profiler tells me) i dont understand why flashPlayer allocates more and more memory - even to the point of crashing. Any ideas here?

Long shot but...
When I had an issue with Flash Builder 4.6 PC mobile in regards to the java heap problem I discovered myself that my project had content which apparently blew out the FB threshold. In particular my mp3 files (3 units) were of too much high quality (360 kbps), I had to scale down the files to 128 kbps. This is an extreme shame.
I am currently running these threshold tests to see if my mp3s can be of better kbps. I did hack my CONFIG scripts in the sdk folders in the installation location but that did not solve my issue. LESSON LEARNED: FB apparently employs the web logic where reduced files equal better performance.

FPGA Base Clocks PCI-5640R

Hi,
 I am using NI PCI-5640R. Following FPGA Base Clocks are available to me:
(1) Configuration_Clk
(2) RTSI_Ref_Clk
(3) DAC_0_IQ_Clk
(4) DAC_1_IQ_Clk
(5) ADC_0_Port_A_Clk
(6) ADC_1_Port_A_Clk
Can anyone help me with brief descriptions of each clock? When these clocks are to be used?
Kindly send me some URL links where I can find details about the usage of these clocks?
Thanks and Regards,
Rashid
Solved!
Go to Solution.

Hello Rashid,
(1) Configuration_Clk - This is 20MHz onboard clock, which runs independently of the other clocks. The role of the 20MHz configuration_clk is to provide a fixed frequecny configuration clock that is use by STC2 ASCI for PCI-DMA operations. Also this clock is not synchronized to the 200MHz VCXO or to the external clock
(2) RTSI_Ref_Clk - This is a device reference clock derived from 200MHz internal VCXO, by setting the dividing factor ranging from 1,2,4,8 and 16.
The I/Q clocks are the signals that indicate the rate of the baseband data. These clocks indicate the rate of the data before the digital upconversion in DAC and the rate of the data after the digital downconversion for ADC. They are described as below.
(3) DAC_0_IQ_Clk and (4) DAC_1_IQ_Clk -
 DAC__IQ_Clk = 2 × REFCLKDAC_ × Clock multiplierDAC_ / InterpolationDAC_
where
REFCLKDAC_ is the specified device reference clock / N2 or 3 CDC. Specify the divisor using the ni5640R CDC Program VI.
Clock multiplierDAC_(M) is equal to 1 or 4 ≤ M ≤ 20. Configure the clock multiplier using the ni5640R DAC Program VI.
InterpolationDAC_ is the hardware interpolation rate determined by the DAC fixed 4× interpolator times a programmable 2× to 63× CIC interpolating filter. The programmable CIC interpolator can be configured using the ni5640R DAC Profile VI.
(5) ADC_0_Port_A_Clk and (6) ADC_1_Port_A_Clk -
 ADC__Port_A_Clk = ENCADC_ × Clock multiplierADC_ / (Predivide FactorADC_ × DecimationADC_)
where
ENCADC_ is the device reference clock / N0 or 1 CDC. Specify the divisor using the ni5640R Configure Timebase VI.
Clock multiplierADC_(M) is equal to 1 or 4 ≤ M ≤ 20. Configure the clock multiplier using the ni5640R Input Port VI.
Predivide FactorADC_ (N) is equal to 1, 2, 4, or 8. Configure the predivide factor using the ni5640R Input Port VI.
DecimationADC_ is the decimation factor for a particular channel in the ADC. Decimation is performed in various filters throughout the processing channel. Each channel includes one CIC filter (decimates by 1 to 32), two FIR-HB filters (each decimates by 2), one DRC filter (decimates by 1 to 16) and one CRCF filter (decimates by 1 to 16). Configure all these filters using the ni5640R ADC Configure DDC VI.
The figure below shows how all the above clocks are derived
Thanks
NI-khil

Can i run remote memory profiling and remote debugging at the same time .

can i run remote memory profiling and remote debugging at the same time .
i am using jdev9.0.5 and oc4j9.0.4 standalone server.
how to write the batch file to run both at the same time

Thanks for your help!
Another question. How do you turn off the ATT wireless transmitter? Also, there are more computers connected to the 2Wire network. I will have to set up a wireless pc to work with the Base Station after disconnecting the ATT transmitter. Easy answers for both, I hope?

Crash when starting a performance/memory profile

I'm having a catastrophic crash when I hit the 'Start' button in the Profile -> Performance and Memory... dialog. There is no error message whatsoever, and when I restart Labview, it only asks me about files to recover, it doesn't tell me where it crashed (i.e. somefile.cpp line ###). Well, it might have told me once, but now it doesn't, so unless there is a log of these things somewhere, I can't say much more.
I'm using Labview 2009, and I'm having the exact same issue on at least 2 machines which are fairly different (Win XP 32 bit vs Win7 64 bit (with Labview 32 bit)).
The application is pretty large (~1500 vi's), so it's kind of hard to tell what is making it crash.
The problem can be replicated in different ways:
1) Load main VI which loads all the VI's in memory
2) Start Performance/Memory profile *crash*
1) Load VI
2) Start VI (runs in a loop)
3) Start Performance/Memory profile while it runs *crash*
1) Start Performance/Memory profile
2) Some NI VI's show up in the list with '0' time everywhere
3) Load VI
4) Execute VI
5) Stop execution of VI *crash*
Any clues? Is there a log somewhere that could help me/you find the issue?
I could spend all day trying to load different parts of the project and look for problems, but I have no idea what to look for.
Last Friday I had successfully profiled what I wanted to, then I had another crash... Oh I remember now... I did a 'Search' in my project, looked for a particular string, and it crashed after a while in the middle of the search. Since then I was unable to use the profile tool. Could it be some data corruption? We use SourceSafe... so I wouldn't be surprised if it gave me a corrupted file If so, how could I find it?
Thank you

Hey Samapico,
I actually found an incident like yours involving the performance and memory tool crashing when used for specific VIs which were very large. How big (in terms of filesize) is your VI?
R&D found this issue in LV 2009 and fixed it in 2010 under Corrective Action Request 215410.
Is there any way you could try and test your issue out on a machine with LV 2010?
<Joel Khan | Applications Engineering | National Instruments | Rice University BSEE>

Unable to run Memory profiling, help please

Hi there,
I installed the lastest version of JDeveloper 10 and created a very simple project(only have one class with Main()method) for testing purpose.
I configure the Profiler in Project Properties page, setting the class as included instance, however, all those profiling menu items(e.g.: Memory Profile...) are greyed out and I am unable to run memory profiling.
I wonder if the functions are available for the free-downloaed version of JDeveloper, or is there something wrong with my setting?
Your help is highly appreciated.

Make sure you are positioned on the class in the application navigator before going to the "run" menu option.
Also does it work if you don't change anything in the project properties?
Here is what I did - created a new project with a simple hello class. And I didn't had any problems profiling it.
There is no function limitation on the version you downloaded.
Here is the class I tried:
public class Class1
public Class1()
public static void main(String[] args)
Class1 class1 = new Class1();
System.out.println("hello");
}

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

Extending using a wireless connection always results in a performance compromise.
If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
Post back to let us know which way to you want to go.

Jdev11g CPU profile and Memory Profile doesn't work for Mac

I'm running Jdev11g on Mac OSX 10.5.5,
CPU Profile and Memory Profile doesn't work. I got following message:
Error occurred during initialization of VM
Could not find agent library in absolute path: /Shared/jdevjavabase11110/jdeveloper/jdev/lib/profiler16.so
The file actually is there. I don't understand why they looking for .so file, it supposed to be mapped as .jnilib on Mac.
This is broken on TP4 as well.

I'm still seeing this issue. Here is what I get:
/System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Home/bin/java -client "-agentpath:/Users/kamleshnanda/Downloads/jdeveloper/jdev/lib/profiler16.so=port=60950,jarpath=/Users/kamleshnanda/Downloads/jdeveloper/jdev/lib/profiler-agent.jar,enable=t,depth=1000,startup=connect,time" -classpath /Users/kamleshnanda/jdeveloper/mywork/MyJavaApplication/Project1/classes project1.Class1 Hello
Error occurred during initialization of VM
Could not find agent library in absolute path: /Users/kamleshnanda/Downloads/jdeveloper/jdev/lib/profiler16.so
Process exited with exit code 1.
I'm using the following build:
About
Oracle JDeveloper 11g Release 1 11.1.1.2.0
Java Edition Version 11.1.1.2.0
Build JDEVADF_11.1.1.2.0_GENERIC_091029.2229.5536
Copyright © 1997, 2009 Oracle and/or its affiliates. All rights reserved.
IDE Version: 11.1.1.2.36.55.36
Product ID: oracle.jdeveloper
Product Version: 11.1.1.2.36.55.36
Version
Component     Version
=========     =======
CVS Version (External)     (CVS) 1.12.13 (client/server)
Java(TM) Platform     1.6.0_17
Oracle IDE     11.1.1.2.36.55.36
PMD     JDeveloper Extension 4.2.5.3.0
Team Productivity Center     11.1.1.2.36.55.36
Versioning Support     11.1.1.2.36.55.36
Here are the JVM properties:
java.runtime.name     Java(TM) SE Runtime Environment
java.runtime.version     1.6.0_17-b04-248-10M3025
java.specification.name     Java Platform API Specification
java.specification.vendor     Sun Microsystems Inc.
java.specification.version     1.6
java.vendor     Apple Inc.
java.vendor.url     http://www.apple.com/
java.vendor.url.bug     http://bugreport.apple.com/
java.version     1.6.0_17
java.vm.info     mixed mode
java.vm.name     Java HotSpot(TM) 64-Bit Server VM
java.vm.specification.name     Java Virtual Machine Specification
java.vm.specification.vendor     Sun Microsystems Inc.
java.vm.specification.version     1.0
java.vm.vendor     Apple Inc.
java.vm.version     14.3-b01-101
Here is the OS information:
os.arch     x86_64
os.name     Mac OS X
os.version     10.6.2

TP4[BUG]: Memory profile and CPU profile doesn't work for MAC

I'm using Mac OSX 10.5.4.
When I try to use Memory profile and CPU profile, I got following error:
Error occurred during initialization of VM
Could not find agent library in absolute path: /Shared/jdevstudiobase1111/jdev/lib/profiler15.so
But the file actually exists.

My MAC version is OSX 10.5.4.
I don't have a stacktrace. It just fails silently.
You can easily reproduce this bug by reformat a readonly file.
Here is the code I reverse engineered from oracle.jdeveloper.refactoring.util.Util.java:
public static boolean setReadOnly(java.net.URL url, boolean readOnly)
boolean ret = false;
java.lang.String cmdarray[] = null;
java.lang.String platformPathName = oracle.ide.net.URLFileSystem.getPlatformPathName(url);
java.lang.String osName = java.lang.System.getProperty("os.name", "");
if(osName.startsWith("Windows"))
cmdarray = (new java.lang.String[] {
"ATTRIB", readOnly ? "+R" : "-R", (new StringBuilder()).append('"').append(platformPathName).append('"').toString()
else
if(platformPathName.equalsIgnoreCase("Linux"))
cmdarray = (new java.lang.String[] {
"chmod", readOnly ? "u-w" : "u+w", (new StringBuilder()).append('"').append(platformPathName).append('"').toString()
if(cmdarray != null)
java.lang.Runtime runtime = java.lang.Runtime.getRuntime();
try
java.lang.Process process = runtime.exec(cmdarray);
if(process.waitFor() == 0)
ret = (new File(platformPathName)).canWrite();
if(ret)
oracle.ide.model.Node node = oracle.ide.model.NodeFactory.find(url);
if(node instanceof oracle.ide.model.TextNode)
oracle.ide.model.TextNode textNode = (oracle.ide.model.TextNode)node;
textNode.isReadOnly();
catch(java.io.IOException e)
e.printStackTrace();
catch(java.lang.InterruptedException e)
e.printStackTrace();
return ret;
}

Memory profiler disabled in JDeveloper 10.1.3.3.0.4157?

Hi,
I'm using JDeveloper 10.1.3.3.0.4157, and it seems that the memory profile is disabled in this version. Or isn't it? How do I enable it?
Thanks in advance!

Make sure your project is using the OJVM.
See: http://blogs.oracle.com/shay/2007/02/are_you_getting_the_most_out_o.html

I just purchased an extreme. I have an express. The sales guy recommended setting up a hot spot with the express and use the extreme as a base station. What does he mean and how do I do this? What are the advantages?

I just purchased an extreme. I have an express. The sales guy recommended setting up a hot spot with the express and use the extreme as a base station. What does he mean and how do I do this? What are the advantages? How do I set this up?????

I think he means to set up the main extreme as the main router or "main base station", and then use the express to "extend" the network.
You can look up the manual for your express here for more details:
http://support.apple.com/manuals/
Extend the range of your network by adding AirPort Express to your existing AirPortExtreme or AirPort Express wireless network (this is called a Wireless DistributionSystem, or WDS). "
Extending the Range of an Existing AirPort Extreme or
AirPort Express Network
You can extend the range of an existing AirPort Extreme or AirPort Express wirelessnetwork by setting it up in a WDS. Wireless computers can connect to the network andshare the Internet connection, share files, and play network games. If you connect yourAirPort Express to your home stereo, computers on your wireless network can useAirTunes to play music on the stereo from iTunes. If you connect a USB printer to yourAirPort Express, all of the computers on the network can print to it.
n Open the AirPort Setup Assistant on a Macintosh, or the AirPort Express Assistant on acomputer using Windows XP. Follow the onscreen instructions to extend the range ofyour AirPort Extreme or AirPort Express network.
Note: Extending the range of a network using WDS may reduce overall networkperformance.

MOVED: What is the Safe OC (base clock) for MSI Eplices plus?

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=130206.0

Hi tancheeru, & welcome to the forum. As this is an OC question, the mods will probably move it to the OC & Modders Section of the forum. Please provide a signature with your systems components. It is difficult to make suggestions without it. In most cases I have experienced, base clock at 166 or 167 will most of the time work on default voltage. However, RAM must be adjusted to compensate for it's increase in speed as base clock is increased. This may involve the Mem. Ratio, Uncore Ratio, timings, & DRAM V.

Extreme Memory Profile & Base Clock - Resolved

Similar Messages

Maybe you are looking for