Extreme slowdown with long articles

Hi,
We're working on a DPS catalog, a very LARGE catalog, in which some of the articles contain many page, each with a set of interactive overlays (mostly 2-5 MSOs). The longest up to now is a 44MB article with 230 pages.
Yes, we know that V swipe of so many pages is not the most logical thing.
We've been experiencing a massive slowdown in the scrolling behavior of long articles.
On iPad 3, it's slow but works.
On iPad 2 it's a bit slower and tends to crash after 50-60 pages.
On iPad 1 it crashes after 15-20 pages.
After switching the article to Horizontal swipe, the behavior is back to normal and there are no more crashes on iPad 1 and 2.
Are there any DPS guidelines to working with long articles?
Is there a page loading scheme that we should be aware of?

Adi, if secrurity terms of the project allow that, send me an original file (few pages), may be I find the problem.

Similar Messages

10.4.6 extreme slowdown and swapfile use

I have an i7 15" with 4gb ram and 80gb free space on its disk.
I had installed Safari 5 before getting the MacOSXUpdCombo 10.6.4.
After the install the problem started. An extreme slowdown with few programs open.
I like to keep an eye on swapfile space so watch /private/var/vm. I found that for the first time I had more than 3 swapfiles. In point of fact I had 13!! or about 10Gigs. This was why the MacBook Pro was almost unusable.
I reinstalled the update and with only Safari running it was again spawning swapfiles. Did all the usual: caches, permissions, disabled extensions and add-ons to safari and it was still eating disk space.
However I may have found the cure. I have just downloaded the standalone Safari 5 installed it and it has so far cured the problem.

Thanks for the suggestion of Whatsize. It didn't reveal any invisible folders with my data inside.
Whatsize from <http://www.id-design.com/software/whatsize/> is intriguing in showing how much garbage is on the HD. It was surprising to see caches that I thought had been deleted were still on the disk.
I am currently back to 95% of files restored from other sources and i'm recovering my distributed assets from the net.
g3 b/W 400 Tower Mac OS X (10.4.5) webserver.com.au
g3 b/W 400 Tower Mac OS X (10.4.5) webserver.com.au

Extreme system slowdown with G5 single and Time Machine.

I am experiencing extreme system slowdown with Time Machine on my G5 1.8 single (PPC). Most of the time it works fine with my system, but there seem to be peak loads where it can take five minutes to command-tab switch between apps. Other times during the same backup, TM functions within acceptable parameters. Is there anything that can be done about this?

I am experiencing extreme system slowdown with Time Machine on my G5 1.8 single (PPC). Most of the time it works fine with my system, but there seem to be peak loads where it can take five minutes to command-tab switch between apps. Other times during the same backup, TM functions within acceptable parameters. Is there anything that can be done about this?

My Macbook is not working properly, I went to a Genius Bar appointment, they were not helpful at all and just told me to go off and reboot my Mac and then restore via TimeMachine. I dont know how to do this. I am extremely displeased with Apple, help me?

My late 2011 Macbook Pro is not working properly it is very slow and extremely painful to use, I went to a Genius Bar appointment, they were not helpful at all and just told me to go off and reboot my Mac and then restore via TimeMachine. I dont know how to do this. I am extremely displeased with Apple at the moment, can someone please help me?

Your problem description is generalized and non-specific. I would make another appointment at the Apple store and insist they help you execute their suggested fixes.
Incidentally, if you search this site, Apple has excellent articles re: restoring a system.
Barry

External hard drive connected to my airport extreme will no longer open, when navigating to it in Finder, the Finder window quits and reopens, cannot access hard drive, it is visible in airport utility, since the problem began I have updated firmware

External hard drive connected to my airport extreme will no longer open, when navigating to it in Finder, the Finder window quits and reopens, cannot access hard drive, it is visible in airport utility, since the problem began I have updated firmware on Extreme as well as both of my Airport Expresses. Hard drive is USB connected to Extreme.

Reboot the USB drive.. assuming it is powered.. or unplug and replug a self-powered drive.. (you should not use self-powered drives on AE before the latest model.. always use a powered hub).
Does the drive now appear in finder..
If not reboot both drive and the AE.. it should now appear.
If it doesn't work with direct connection try a powered hub.. that can help.

HT1145 The airport extreme used with my iMac is not seeing my other devices...anybody, please?

The airport extreme used with my iMac is not seeing my iPhone 5, iPad (third generation) or my windows based PC. When I open the airport utility it shows only the internet and my iMac. It does not identify the others. Any thoughts? Thanks

Hi DaileyT,
Thanks for using Apple Support Communities.
For more information on this, take a look at this article:
When do Apple wireless devices appear in AirPort Utility?
http://support.apple.com/kb/HT3624
Troubleshooting missing devices
If your Apple wireless device doesn't show up in the wireless device list, try the following:
Check to see that the device is turned on.
Check that the device is connected to the network via Ethernet or in wireless range of your computer.
Make sure the device has had adequate time to start up and become discoverable. In the case of Apple wireless devices that are not connected via Ethernet, AirPort Utility scans for new devices once every 15 seconds. From the time a device becomes discoverable (typically around one minute), it could take up to another 15 seconds before the device is displayed in the list.
If you have just configured a new Apple Wireless device, upgraded the firmware, selected "Restore Default Settings..." or have hard reset and configured an Apple wireless device and it does not show up in AirPort Utility after restarting, you may have an incorrect setting. You may want to hard reset the unit and set it up again.
If you are connected to a specific wireless network, all Apple wireless devices which make up that network will appear. However, if you "Restore Default Settings..." from AirPort Utility, or hard reset a device that is out of physical wireless range of the computer, you will need to move the device closer the computer to configure it again.
Best of luck,
Mario

[svn] 4028: Bug: Draining of buffered messages doesn' t work correctly with long-polling.

Revision: 4028
Author: [email protected]
Date: 2008-11-06 09:04:26 -0800 (Thu, 06 Nov 2008)
Log Message:
Bug: Draining of buffered messages doesn't work correctly with long-polling.
QA: Yes - please make sure both nio and regular long-polling channels work with throttling.
Doc: No
Checkintests: Pass.
Details: Made sure that buffered messages are drained properly with all polling channels (polling, long-polling, and nio-long-polling).
Modified Paths:
blazeds/trunk/modules/core/src/flex/messaging/client/FlexClient.java

Sounds like you've probably already looked but the CUPS article in the wiki led me through setting up a printer without any problems. http://wiki.archlinux.org/index.php/CUPS
The first section describes how to troubleshoot CUPS and printing problems.
I've also found a few other posts and links that may help.
http://hplipopensource.com/hplip-web/mo … eries.html
http://ubuntuforums.org/showthread.php?t=419163
Hope this helps!

Smooth scrolling long articles still snaps on iPad retina and mini

I have some long articles (between 6000px and 9000px). On the iPad 1 the smooth scroll works fine, but on the iPad retina and mini the articles are snapping to undefined points in the article. Now the articles are impossible to read on the iPad retina and mini. Using PFD or JPG in the article properties doesn’t matter.
Anyone knows why this works on iPad 01 and doesn’t work in the retina and mini version? THX
Bests, Puck

Hi Bob,
Thank you for replying.
I just need one image in each state though -- that is shown anytime a user clicks on a button, so how would I limit the functionality of an image sequence to just show one photo while creating an MSO with a button? Would that mean creating a folder per image with one 01.jpg image in it and then making these 3 placeholders into an MSO? It seems to me that an image sequence is not providing the functionality I want and this is some sort of a hack unless I am misunderstanding its function.
Sounds like a lot of redudant work instead of having a simpler way to show an MSO with high-res photos on an iPad 3/4 and smaller images on iPad 1/2 and Mini.
Thanks,
Alon

My computer is extremely slow, with the rainbow wheel appearing with every click. It is one year old, and has all the most recent updates. Why is it so painfully slow?

My computer is extremely slow, with the rainbow wheel appearing with every click. It is one year old, and has all the most recent updates. Why is it so painfully slow?

That sounds horrible. There are a number of reasons it could occur.
The first thing to do is ensure you have adequate backups, because what you describe can be a symptom of impending disk failure.
To help determine the possible causes of this behaviour read the following. None of what follows is intended to fix anything, but it will provide the additional information required to advance troubleshooting. There are four separate parts to it; read everything first.
Boot OS X Recovery by holding ⌘ and r (two fingers) while you start your Mac. At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red. If Disk Utility reports "The volume Macintosh HD appears to be OK" in green then you can be reasonably (though not completely) assured your hard disk is in good working order.
When it finishes restart your Mac and test again for operation. If it's still not behaving as you expect it should, please post the results of EtreCheck in accordance with the following instructions:
Apple Support Communities contributor etresoft wrote a very useful app to quickly gather certain system information that may help point to a cause of this problem. Read about it here. It contains a link to download EtreCheck. Don't download it from anywhere else (such as may be found by following the results of an Internet search).
Click Open - etresoft contributes to this forum frequently and can be considered a trustworthy developer.
It will take a moment to run as it collects its data.
Copy and paste its output in a reply.
Do not be concerned about anything that says "Problem" or “failed” or anything else that may appear in red.
EtreCheck was designed to remove any personal information (such as your computer's name and serial numbers) but if you see anything that looks like an email address or any other personal information that should not be divulged to others, please delete or obscure that information when you post the reply.
When you are finished with EtreCheck, quit the program. It occupies very little space, and you can keep it or drag it to the Trash as you wish.
After completing the above please determine if the problems also occur in "Safe Mode":
Safe Mode or "Safe Boot" is a troubleshooting mode that bypasses all third party system extensions and loads only required system components. Read about it: Starting up in Safe Mode
You must disable FileVault before you can start your Mac in Safe Mode.
Starting your Mac in Safe Mode will take longer than usual, graphics will not render smoothly, audio is disabled on some Macs, and some programs (iTunes for example) may not work at all.
Merely starting your Mac in Safe Mode is not intended to resolve the problem, it's to observe its performance without certain additional components.
To end Safe Mode restart your Mac normally. Shutdown will take longer as well.
System performance problems for reasons that cannot be isolated to any other cause justify an SMC reset. Be sure to read the procedure carefully and follow all the steps exactly as written, even if they seem inapplicable or trivial.

CS4 Installation Causing Extreme Slowdowns

I recently installed CS4 on my computer (HP xw4300 workstation). In the process I somehow lost my user profile and am experiencing extreme slowdowns when trying to open any of the CS4 programs. I actually talked to HP customer service and they said there is no reason (memory capability, etc...) as to why this should be happening. Any suggestions?

Hi Ellie,
To fix your problem, I would suggest adding memory to your system. Your processor seems to be O.K. (but nothing more), so investing a tiny $25 into memory would be a good solution possibly.
Add another GB of RAM or so. If that is too expensive, get this RAM.
If you are not experienced in computer maintenance, make sure you follow the simple steps of installing more memory. It really isn't that hard. And unless you go rubbing your feet around on the carpet and come back to shock your computer, you're not going to wreck it. Just remember to ground yourself once in a while on the power supply (the box inside the computer case).
I don't know how much you know, so here's some simple steps:
Turn your computer off
Unplug it (fat black cord)
Wait about 30 seconds (the motherboard holds power for a little while)
Open the case (the 'box' that makes the noise when it's on)
Ground yourself to the power supply by touching the metal housing (again, this is the *usually silver box inside the case - around where you pulled the cable from the back)
Find the slots for the memory (make sure there is no dust in the slots!)
Open the clasps and put the sticks in evenly with equal amount of pressure on both sides until they snap in
Close the case
Plug it in
Turn it on
Once the PC is on and you're logged on, press the windows key (on the bottom - between the 'Ctrl' and 'Alt' keys) and the 'Pause/Break' button at the same time. This will bring up your system properties. Depending on how much RAM you bought, it should show something like 1.5GB or 2.5GB or a large number of MB's (2444MB for example). If it still shows 512MB, you either didn't install the chips correctly or the system isn't recognizing them.
Hope this helps.
-Michael D

Does Airport Extreme works with Lenovo ThinkPad(L420), Does Airport Extreme works with Lenovo ThinkPad(L420)

Does Airport Extreme works with Lenovo ThinkPad(L420), Does Airport Extreme works with Lenovo ThinkPad(L420)

The AirPort Extreme fully implements the IEEE 802.11 wireless protocols for a through n and will work with any computer that uses a compliant version of any of those protocols. So, yes it will work with the Lenovo as long as the Lenovo is not doing something strange with wireless.

Problem with Long and BigDecimal DataType convertion

HI,
I have an application which talk to MySQL database with Spring JDBC layer and everything runs like a champ :)
Now I am converting the same application with the same DAO implementation to communicate with oracle database and I am having some trouble converting DataType from database to my java code.
For example before with MySQL I would convert any Integer coming from the database to Long datatype and it worked. Now it seems that Int datatype from oracle comes as a BigDecimal type.
I am thinking about two approaches writing an additional implementation to implement my dao interfaces or if there is some trickery that I can bypass doing that and work around these datatype incompatibility from MYSQL to Oracle.
I can also put bunch of try and catch statements and if fails with Long try with BigDecimal, but still don't buy it as the best solution.
Here use also code snippet:
User u = new User();
                    u.setObjectId((Long) m.get("oid"));//This works with MYSQL backend but not with Oracle so the raw object seem to be coming as BigDecimal datatype
                    u.setLogon((String) m.get("logon"));
                    u.setPassword((String) m.get("password"));
                    u.setName((String) m.get("uname"));
                    u.setCompany(companyDAO.getById((Long) m.get("cOid")));Any help will be appreciated.
Edited by: kminev on Mar 3, 2010 12:25 PM

//This is my entity class
public class User implements Comparable<User> {
    private Long objectId = 0L;
    private Company company;
    private String logon = "";
    private String password = "";
    private String name = "";
    private boolean hasAdminRights=false;
    private boolean hasMaintenanceRights=false;
//This is my bean class
<bean id="userDAO" class=" com.myorg.myapp.dao.jdbc.UserImpl">
        <property name="transactionManager">
            <ref local="transactionManager"/>
        </property>
        <property name="companyDAO">
            <ref local="companyDAO"/>
        </property>
        <property name="companyAccessDAO">
            <ref local="companyAccessDAO"/>
        </property>
    </bean>

Problem with long text

Hi folks,
iam uploading longtext in transaction KP06 in bdc programing using create_text.
now my problem is if i pass selection criteria
case 1:
Vertion : N0
fiscal year : 2007
planner profile: CCPLAN4
then the budeget plan data uploading successfully along with long text.
case2: Vertion : N1
in this case also everthing wrking fine
case3: Vertion : 001
in this case budgetplan data uploading sucessfully but longtext is not uploading,
i debbug the proragm , create_text also returning sy-subrc = 0. but if i check in KP06 the long text is not there.
data declaration
vertion : VERSN type C(3)
can u tell me the problem is in logic or with FM ?
note : i checked with save_text also.
regards
neeru

HI Naimesh,
the FM Create_text internally contains both FMs save_text and commit_text,
even i debug the FM in case of vertion N1, N0 and 001,
all the cases sy-subrc = 0.
code:
CLEAR G_OBJNR.
LOOP AT RECORD.
COST = RECORD-BDC01.
CALL FUNCTION 'CONVERSION_EXIT_ALPHA_INPUT'
    EXPORTING
      input = COST
    IMPORTING
      output = COST.
    CONCATENATE 'KS' p_kokrs record-bdc00 INTO g_objnr.
        SELECT SINGLE * FROM COSP WHERE OBJNR = g_objnr
                          AND GJAHR = P_GJAHR
                          AND VERSN = p_ver
                          AND KSTAR = COST.
IF SY-SUBRC = 0.
      LEDNR = COSP-LEDNR.
      OBJNR = COSP-OBJNR.
      GJAHR = COSP-GJAHR.
      WRTTP = COSP-WRTTP.
      VERSN = COSP-VERSN.
      KSTAR = COSP-KSTAR.
      HRKFT = COSP-HRKFT.
      VRGNG = COSP-VRGNG.
      VBUND = COSP-VBUND.
      PARGB = COSP-PARGB.
      BEKNZ = COSP-BEKNZ.
      TWAER = COSP-TWAER.
CONCATENATE LEDNR OBJNR INTO OBJNR.
CONCATENATE OBJNR GJAHR INTO TNAME1 separated BY SPACE10.
CONCATENATE TNAME1 WRTTP VERSN INTO TNAME2.
CONCATENATE TNAME2 KSTAR INTO TNAME3 separated BY SPACE.
CONCATENATE TNAME3 VRGNG INTO TNAME4 separated BY SPACE4.
CONCATENATE TNAME4 BEKNZ INTO TNAME5 separated BY SPACE10.
CONCATENATE TNAME5 TWAER INTO TNAME.
I_THEAD-TDOBJECT = 'CCSS'.
I_THEAD-TDID = 'COSP'.
I_THEAD-TDNAME = TNAME.
I_THEAD-TDSPRAS = 'E'.
APPEND I_THEAD.
i_tline-tdformat = '*'.
I_TLINE-TDLINE = RECORD-LONGTEXT.
APPEND I_TLINE.
loop at i_thead.
CALL FUNCTION 'CREATE_TEXT'
EXPORTING
    FID               = I_THEAD-TDID
    FLANGUAGE         = I_THEAD-TDSPRAS
    FNAME             = I_THEAD-TDNAME
    FOBJECT           = I_THEAD-TDOBJECT
SAVE_DIRECT       = 'X'
FFORMAT           = '*'
TABLES
    FLINES            = i_tline
EXCEPTIONS
NO_INIT           = 1
NO_SAVE           = 2
OTHERS            = 3
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
         WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
ENDLOOP.
CLEAR I_TLINE.
REFRESH I_TLINE.
CLEAR I_THEAD.
REFRESH I_THEAD.
SELECT SINGLE * from cokp into itab WHERE OBJNR = g_objnr
                          AND GJAHR = P_GJAHR
                          AND VERSN = p_ver
                          AND KSTAR = COST.
if sy-subrc = 0.
   itab-TXFLG = 'X'.
   append itab.
   write:/ 'Text saved for', record-bdc00 , record-bdc01.
   else.
      write:/ 'Text saved for', record-bdc00 , record-bdc01.
      ENDIF.
ENDIF.
my program wrking fine but the long text is not visible for vertion 001.
regards
niru

Using DBMS_DATAPUMP with LONG data type

I've got a procedure below that calls the DBMS_DATAPUMP procedure using a REMOTE_LINK to move a schema from one database to another. However, a couple of the tables within that schema have columns with the LONG data type. And when I run it I get an error saying that you cannot move data with the LONG data type using a REMOTE LINK. So no data in those particular tables gets moved over.
Has anyone else had this issue? If so, do you have a work around? I tried adding a CLOB column to my table and setting the new CLOB to equal the LONG, but I couldn't get that to work either...even when I tried using a TO_LOB. If I could get that to, then I could just drop the LONG, move the schema, then recreate the LONG column on the opposite side.
Here's my procedure....
DECLARE
     /* EXPORT/IMPORT VARIABLES */
     v_dp_job_handle                    NUMBER ;          -- Data Pump job handle
     v_count                              NUMBER ;          -- Loop index
     v_percent_done                    NUMBER ;          -- Percentage of job complete
     v_job_state                         VARCHAR2(30) ;     -- To keep track of job state
     v_message                         KU$_LOGENTRY ;     -- For WIP and error messages
     v_job_status                    KU$_JOBSTATUS ;     -- The job status from get_status
     v_status                         KU$_STATUS ;     -- The status object returned by get_status
     v_logfile                         NUMBER ;
     v_date                              VARCHAR2(13) ;
     v_source_server_name          VARCHAR2(50) ;
     v_destination_server_name     VARCHAR2(50) ;
BEGIN
     v_project := 'TEST' ;
     v_date := TO_CHAR(SYSDATE, 'MMDDYYYY_HHMI') ;
     v_source_server_name := 'TEST_DB' ;
     v_dp_job_handle := DBMS_DATAPUMP.OPEN(
          OPERATION     => 'IMPORT',
          JOB_MODE     => 'SCHEMA',
          REMOTE_LINK => v_source_server_name,
          JOB_NAME     => v_project||'_EXP_'||v_date,
          VERSION          => 'LATEST') ;
     v_logfile := DBMS_DATAPUMP.KU$_FILE_TYPE_LOG_FILE ;
     DBMS_DATAPUMP.ADD_FILE(
          HANDLE          => v_dp_job_handle,
          FILENAME     => v_project||'_EXP_'||v_date||'.LOG',
          DIRECTORY     => 'DATAPUMP',
          FILETYPE     => v_logfile) ;
     DBMS_DATAPUMP.METADATA_FILTER(
          HANDLE          => v_dp_job_handle,
          NAME          => 'SCHEMA_EXPR',
          VALUE          => '= '''||v_project||''' ') ;
     DBMS_DATAPUMP.START_JOB(v_dp_job_handle) ;
     v_percent_done := 0 ;
     v_job_state := 'UNDEFINED' ;
     WHILE (v_job_state != 'COMPLETED') AND (v_job_state != 'STOPPED')
     LOOP
          DBMS_DATAPUMP.GET_STATUS(
               v_dp_job_handle,
               DBMS_DATAPUMP.KU$_STATUS_JOB_ERROR + DBMS_DATAPUMP.KU$_STATUS_JOB_STATUS + DBMS_DATAPUMP.KU$_STATUS_WIP,
               -1,
               v_job_state,
               v_status) ;
               v_job_status := v_status.JOB_STATUS ;
          IF v_job_status.PERCENT_DONE != v_percent_done THEN
               DBMS_OUTPUT.PUT_LINE('*** Job percent done = '||TO_CHAR(v_job_status.PERCENT_DONE)) ;
               v_percent_done := v_job_status.PERCENT_DONE ;
          END IF ;
          IF BITAND(v_status.MASK, DBMS_DATAPUMP.KU$_STATUS_WIP) != 0 THEN
               v_message := v_status.WIP ;
          ELSIF BITAND(v_status.mask, DBMS_DATAPUMP.KU$_STATUS_JOB_ERROR) != 0 THEN
               v_message := v_status.ERROR ;
          ELSE
               v_message := NULL ;
          END IF ;
          IF v_message IS NOT NULL THEN
               v_count := v_message.FIRST ;
               WHILE v_count IS NOT NULL
               LOOP
                    DBMS_OUTPUT.PUT_LINE(v_message(v_count).LOGTEXT) ;
                    v_count := v_message.NEXT(v_count) ;
               END LOOP ;
          END IF ;
     END LOOP ;
     DBMS_OUTPUT.PUT_LINE('Job has completed') ;
     DBMS_OUTPUT.PUT_LINE('Final job state = '||v_job_state) ;
     DBMS_DATAPUMP.DETACH(v_dp_job_handle) ;
END ;

But the application we have that uses the database cannot be changed to read from a CLOBWhy can't you change the application?
Well, anyway you should point out to your superiors that Oracle documented years ago to not use LONGS anymore...
http://download.oracle.com/docs/cd/B19306_01/server.102/b14220/datatype.htm#sthref3806
It clearly states:
LONG Datatype
Note:
Do not create tables with LONG columns. Use LOB columns (CLOB, NCLOB) instead. LONG columns are supported only for backward compatibility.
Oracle also recommends that you convert existing LONG columns to LOB columns. LOB columns are subject to far fewer restrictions than LONG columns. Further, LOB functionality is enhanced in every release, whereas LONG functionality has been static for several releases.
How do I go from CLOB to LONG?I'm sorry, cannot help you on that one, I don't think you can do that at all (Oracle wants us to stop using LONGS, so, it's a one-way conversion...):
http://asktom.oracle.com/pls/asktom/f?p=100:11:0::::P11_QUESTION_ID:1037232794454#15512131314505
So: NO built_in, you'll need to write a program if the clob is ALWAYS LESS THAN 32k in size, you can use plsql..but is that the case in your case? Only you know that.
I believe that question is still unanswered on this forum, but you might try searchin for answers on this forum, and
the 'Database-General' forum: General Database Discussions
Perhaps you can google a Q&D workaround...
( And consider convincing your collegues to just convert your LONGS to LOBS)
Edited by: hoek on Apr 8, 2009 5:43 PM

Saving Outlook eMail to a hard drive folder with long subject lines

I'm using Outlook 2010 on a WIN7 machine. I drag and drop eMails to folders on my desktop quite often and in the past (earlier version
of Outlook) I would receive a warning that the file did not copy if the subject line was too long. When I drag and drop eMails with long subject lines now there is no visual warning or indication that the operation failed. I am aware of the file name/path
character count limitation. My issue is the lack of a warning when the operation fails requiring me to have to check the length of the subject line before the operation or double check if the file is present after the operation. Checking after the operation
is quite exacerbating when you are copying 15 - 20 files at a time. Is there a patch or something that can be done about this?

Hi,
We can also consider to get support about macro from MSDN forum:
http://social.msdn.microsoft.com/Forums/office/en-US/home?forum=outlookdev
Regards,
Melon Chen
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

Extreme slowdown with long articles

Similar Messages

Maybe you are looking for