Extremely slow speeds on EAP-TTLS PAP secured network

I have a Dell Inspiron 1525 with a Broadcom 4312 wireless chip and when I connect to my schools network I get speeds that are as low as 100 K/s or slower.
When I go to speedtest.net I get speeds of 10 M/s down. I have tried using both the B43 and wl drivers and I get about the same speed on speed test and still very slow speeds when updating through pacman or downloading files.
I am running the most recent versions of the kernel and all drivers.
Here is the output from lspci:
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
If you guys have any ideas of what might help I'm willing to try it, thanks in advance.

Visited the Apple store today and they replaced the phone. They could not explain what was going on except for being a software issue.
They said if after restoring I have the same issue, you would have to restore the phone to new and re-install all apps and information manually from scratch.
I restored the phone from my backup, and all went well. No more slow LTE speeds, plus a new device.
The only thing I can think of that may have happened is updating carrier settings while updating the iOS at the same time. I thought it was normal because iTunes popped up the carrier update notification a few seconds later after starting the iOS 8 update.
The carrier update did have an option to cancel. I will definitely wait for the iOS update to complete before I update carrier settings next time.
I'm just wondering if my phone was out of warranty, and this happened, would Apple still replace the device?

Similar Messages

Extremely slow speeds on Windows Computers with 5th Generation AirPort Extreme

I just got a new refurbished AirPort Extreme 5th generation. Everything works great for all of my OS X devices and iOS Devices. I am getting my ISPs speeds when doing tests. The issue is when I am using Windows devices. My roommate has a desktop and a netbook and both are getting extremely slow speeds. Speeds like .07Mbps down. Does anyone have any idea what the issue might be?

You have no large file?? Really.. in the whole computer there is not a windows update file.. a backup file... a movie download file.. nothing.. ??
Anyway that is irrelevant.. the issue is wireless.
Download the latest drivers from the wireless manufacturer.
You will need to find out what wireless card is used and locate the correct download for that model.
On the Airport it is well worth doing the following tests.
1. Change the name to SMB standard.. short no spaces pure alphanumeric.
So if your wireless name is Fred Blog's Airport Extreme wireless
Plesae change it to AEwifi
2. Take off all security for a test.
3. Set channels.. I am guessing the computers are only using 2.4ghz, so set 11,6, 1 in that order.
No improvement.. just put the security back to WPA2 Personal with pure alphanumeric password..
Try and test new drivers and use no firewalls on the computer.. ensure that the computer is correctly set for home network.
Beyond that it is just incompatible.

N95 EAP-TTLS + PAP

With the plethora of encryption options available on the N95 I was highly surprised to notice that PAP was not an option. My University network (UPenn) requires EAP TTLS PAP. Does anybody know if this will be incorporated in the future via firmware or other (possibly third party) software?
Thanks!

I've just made Eduroam work on my N95 in Oxford University thus (I'm on firmware 11.0.026 date 17-04-07):
1. Make sure the root certificate for the authority that signed your radius servers' certificate is in the root store of your phone. Oxford uses Globalsign which is not there by standard.
2. Choose WPA/WPA2 for the WLAN Security Mode
3. Choose EAP as the WPA/WPA2 type
4. Choose WPA2 only mode and make sure it is off
5. In the EAP plug-in settings enable only EAP-TTLS and choose that. Set the Authority Certificate to match the one that signed your radius server's certificate.
6. Set your username and realm both to be user-defined and put them in the right boxes (my realm is ox.ac.uk).
7. Use the right of the centre button to move on the EAPs tab and enable "EAP-MSCHAPv2" ONLY. DO NOT ENABLE "MSCHAPv2".
8. In the settings for EAP-MSCHAPv2 provide your username (and password if you wish, or set it to prompt for it).
As we say in England, Robert is then your parent's brother.
You should now be able to use that network connection for web browsing, email, SIP and anything else you might choose.

E61 EAP-TTLS PAP

I'm trying to connect to a network secured by EAP-TTLS PAP. Is there a plug-in that I'm missing or is it available in the latest firmware?

23-Oct-2006
12:05 PM
e61drc wrote:
does not support EAP-TTLS-PAP and this functionality cannot be added
Yeah sure....there is a diference between cannot and will not be. I am pretty sure that it is possible to add pap since there are no hardware limitations for adding it.
BTW why does it say plugin if you can't add a plugin?

Support for EAP-TTLS-PAP (as used by Eduroam) in N...

When it will be available a solution to the lack of support for EAP-TTLS-PAP (as used by Eduroam) in Nokia N86 8MP throught a new firmware?
To many years waiting... Must we go to another solution?
Thx.

I have succeed to import the local certificate using the instructions in
http://www.jacco2.dds.nl/networking/symbian_cert_import.html
then the description in
http://www.reading.ac.uk/internal/its/eduroam/its-eduroam-config-nokia-n95.aspx
works with the given certificate.

WiFI authentication and Eduroam (EAP-TTLS / PAP)

Hi,
eduroam (EDUcation ROAMing) is the roaming infrastructure used by the international research and education community (universities).
At least in Australia and AFAIK also in Europe.
Most sites use EAP-TTLS / PAP authentication (and it appears there are good technical reasons for it).
The current Symbian OS does not support it out of the box.
(or at least I couldn't find it on my E51)
Is there any solution (application, etc) able to supply this functionality ?
Cheers.

e61drc: thanks, indeed, you are correct.
bife71: the e51 have mschapv2 (guess what ms stands for which require an active directory backend while pap may use practically anything (e.g. an ldap) ... this being a good technical reason why large organizations may prefer pap.
Well, from a company claiming "Connecting People" I am rather disapointed.
(further research turned out that this feature have been widely requested for at least 1.5 years)
Cheers.

Wi-fi eap-ttls - PAP inner security?

i've just got a blackberry 8900 and i can't connect to faculty wireless network due to a "pap - inner link security" demand.
anyone knows any program that can solve that? i've googled a bit and haven't found anything. (few opened topics that all end without a solution).
too bad blackberry doesn't support this since lots of universities (www.eduroam.org) and public organizations use this kinda protection, at least in my country. i believe this is a software, not hardware issue, any ideas on this "feature" ? any words from the developers on this issue?
greetz, robert

TTLS-PAP is also used commonly by many organizations with non-Microsoft directory systems. And is commonly used by American universities as well. All three of the schools I attended, Harvard, Berkeley and UPenn, all used TTLS-PAP to secure their wireless networks.... Wild guess, those schools could be filled with idiots, but I'd venture a guess that they have people smart enough to deploy a wifi network properly.
Xandrex wrote:
It's a question of being secure, and of being tolerant towards servers that are not secured.
This isn't accurate. Yes, PAP is not a secure password exchange method. But it is being sent through a TLS tunnel which is very secure. That is like saying sending a password in a web form through a SSL tunnel isn't secure. Well, actually, it is.
Also, it isn't for RIM to decide what is / isn't secure on user's wireless networks. Your analogy of SSLv2 just doesn't jive. If security was even an issue (it isn't) and PAP isn't supported because the RIM's great banevolence to their users, why is WEP still support? Or why are open networks supported?
All arguments aside TTLS-PAP is a very commonly used 802.1x authentication method supported by Windows Mobile, iPhone, Web OS, Mac OS X and Windows... RIM needs to get it together on this one.

Connecting EAP-TTLS-PAP network on 5800

I am studying at RMIT University and we have both eduroam as well as the university's own WPA network. I was trying to connect to it (V50) and was unable to connect. I was using the help of this guide http://sites.google.com/site/pramudi/connecting-to-eduroam-on-nokia-5800-symbian-s60v5 before I found out that RMIT uses 802.11x security mode with PAP encryption. Can anyone help me? Here's a link to their setup guide for Linux: http://mams.rmit.edu.au/ua7mgpk79jzez.pdf
I set it up and then it says TTLS authentication failed.

I've just made Eduroam work on my N95 in Oxford University thus (I'm on firmware 11.0.026 date 17-04-07):
1. Make sure the root certificate for the authority that signed your radius servers' certificate is in the root store of your phone. Oxford uses Globalsign which is not there by standard.
2. Choose WPA/WPA2 for the WLAN Security Mode
3. Choose EAP as the WPA/WPA2 type
4. Choose WPA2 only mode and make sure it is off
5. In the EAP plug-in settings enable only EAP-TTLS and choose that. Set the Authority Certificate to match the one that signed your radius server's certificate.
6. Set your username and realm both to be user-defined and put them in the right boxes (my realm is ox.ac.uk).
7. Use the right of the centre button to move on the EAPs tab and enable "EAP-MSCHAPv2" ONLY. DO NOT ENABLE "MSCHAPv2".
8. In the settings for EAP-MSCHAPv2 provide your username (and password if you wish, or set it to prompt for it).
As we say in England, Robert is then your parent's brother.
You should now be able to use that network connection for web browsing, email, SIP and anything else you might choose.

ITunes is extremely slow and I cannot make a secure connection

When I connect to iTunes my computer is extremely slow, and when I try to connect to the iTunes store I get the error message cannot make a secure connection. I have internet access and I have ran the iTunes diagnostics test and all the tests passed except making a secure connection. I have disabled all of my security systems including my firewall and Norton. I am not running any proxy settings. This has been an ongoing problem for over a month and I am at a loss.

Check out this Apple article -> iTunes: Advanced iTunes Store troubleshooting
Blocked by configuration: (Mac OS X/Windows)
Configure Internet Options (for Windows computers only):
Run iTunes Diagnostics. If the "Secure link to iTunes Store" section does not pass, do the following.
Open Internet Explorer.
From the Tools menu, choose Internet Options.
Click Connections.
Under "Dial-up and Virtual Private Networking," choose "Never dial a connection." It may not be possible to choose this if you’ve never used dial-up Internet; if this is the case, skip to the next step.
Click LAN Settings.
In the window that opens, enable the option to "Automatically detect settings" if it is not enabled.
iTunes uses Internet Options proxy settings. Apple recommends removing proxy settings that interfere with access to the iTunes Store if needed.
Click OK.
Click the Advanced tab.
Scroll down to the Security section and look for the option to "Check for server certificate revocation." If it is enabled, disable it.
Look for Use SSL 3.0 and Use TLS 1.0. Make sure at least one of those two checkboxes is selected and click OK (You can select both checkboxes).
Apply any changes, and restart your computer if you modified the option to "Check for server certificate revocation" (step #11).

Reset hub and now getting extremely slow speeds...

Hi there,
So I have had bt broadband for 3 months and had nothing but problems. The speed is very slow, though I do live in a rural area so somewhat to be expected. However in the evenings I have noticed I can get extremely high pings (1000+) and slow speeds (below 0.5 mbps).
Recently however my usual daytime speeds of around 1.2 mbps shot up to around 3 mbps, which to me is quite high! (compared to what I have been getting).
Though it dropped off a bit over the past few days (to around 2.2 mbps) it was still working ok, until last night when I reset my homehub as my sister was unable to connect to it at all.
Since then I have had nearly none existant speeds. Even getting on here was a mission. I am getting speeds of around 0.10 mbps, though my ping seems to vary wildly from around 50 all the way back up to silly numbers.
I attempted to use the bt speed test, but it told me it couldn't get a reading cos my line was too slow!
I did however get one eventually from BT wholesale as below. (it won't let me copy it in?...)
Download speed (mbps): 0.14
Upload speed (mbps): 0.35
Ping Latency (ms): 69.63
Speedtest.net give the following
Really getting fed up with the unreliable and slow connection. When added to the problems getting a line installed in the first place (it took 3 months!) and problems I have had in the past, I am seriously looking to see what other options I have, but there aren't many good providers that will set us up out here
Can anyone help me get a stable, reasonably fast connection?
Thanks,
Richard

Hi,
Here are the adsl stats
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 01:19:52
Downstream:
512 Kbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
38.7 dB / 17.0 dB
Line attenuation (Down/Up):
14.4 dB / 8.0 dB
Output power (Down/Up):
17.6 dBm / 12.3 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
1 / 0
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 0
Error Seconds (Local/Remote):
1 / 0
I currently have the hub connected to the master socket via a filter. I have tried on the main socket and master socket with two different filters and nothing changed...
As for the btspeedtester, I was unable to successfully run that...It just says my connection may be too slow (no kidding!)
Finally, regarding the quiet line test...I don't actually have a phone at the moment. I only wanted broadband as I rarely make phone calls from the house and use my mobile. I am looking to get one for the sole purpose of fixing this issue (and ringing bt to have a whinge at them)
Thanks,
Richard

MacBook Pro(Early 2011) extremely slow speed on Yosemite(10.10.2)

Hi All,
I installed and then reinstalled a fresh Yosemite But now i am experiencing issues like very slow speed of the OS & fan continuously ON. Mavericks was working fine.
this is my ertecheck report
EtreCheck version: 2.1.8 (121)
Report generated 1 April 2015 12:03:11 am IST
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
    MacBook Pro (13-inch, Early 2011) (Technical Specifications)
    MacBook Pro - model: MacBookPro8,1
    1 2.7 GHz Intel Core i7 CPU: 2-core
    10 GB RAM Upgradeable
        BANK 0/DIMM0
            2 GB DDR3 1333 MHz ok
        BANK 1/DIMM0
            8 GB DDR3 1333 MHz ok
    Bluetooth: Old - Handoff/Airdrop2 not supported
    Wireless: en1: 802.11 a/b/g/n
    Battery Health: Replace Soon - Cycle count 1329
Video Information: ℹ️
    Intel HD Graphics 3000 - VRAM: 512 MB
        Color LCD 1280 x 800
System Software: ℹ️
    OS X 10.10.2 (14C1514) - Time since boot: 4:1:57
Disk Information: ℹ️
    Hitachi HTS545050B9A302 disk0 : (500.11 GB)
        EFI (disk0s1) <not mounted> : 210 MB
        Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
        MacHDD_2 (disk0s4) /Volumes/MacHDD_2 : 349.63 GB (118.65 GB free)
        MacHDD_1 (disk1) / : 149.11 GB (104.40 GB free)
            Core Storage: disk0s2 149.48 GB Online
    MATSHITADVD-R   UJ-898
USB Information: ℹ️
    Apple Inc. FaceTime HD Camera (Built-in)
    Apple Inc. Apple Internal Keyboard / Trackpad
    Apple Inc. BRCM2070 Hub
        Apple Inc. Bluetooth USB Host Controller
    Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
    Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
    Mac App Store and identified developers
Launch Daemons: ℹ️
    [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
User Launch Agents: ℹ️
    [loaded]    com.google.keystone.agent.plist [Click for support]
User Login Items: ℹ️
    iTunesHelper    Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
    Google Chrome    Application Hidden (/Applications/Google Chrome.app)
Internet Plug-ins: ℹ️
    Default Browser: Version: 600 - SDK 10.10
    QuickTime Plugin: Version: 7.7.3
    SharePointBrowserPlugin: Version: 14.4.8 - SDK 10.6 [Click for support]
3rd Party Preference Panes: ℹ️
    None
Time Machine: ℹ️
    Mobile backups: OFF
    Auto backup: NO - Auto backup turned off
    Volumes being backed up:
        MacHDD_1: Disk size: 149.11 GB Disk used: 44.71 GB
    Destinations:
        MacHDD_2 [Local]
        Total size: 349.63 GB
        Total number of backups: 0
        Oldest backup: -
        Last backup: -
        Size of backup disk: Adequate
            Backup size 349.63 GB > (Disk used 44.71 GB X 3)
Top Processes by CPU: ℹ️
        26%    Microsoft Outlook
        12%    coreaudiod
         6%    Google Chrome
         3%    WindowServer
         1%    launchservicesd
Top Processes by Memory: ℹ️
    215 MB    mds_stores
    193 MB    Google Chrome
    183 MB    Google Chrome Helper
    129 MB    iTunes
    107 MB    Microsoft Outlook
Virtual Memory Information: ℹ️
    5.04 GB    Free RAM
    3.41 GB    Active RAM
    698 MB    Inactive RAM
    1.59 GB    Wired RAM
    4.71 GB    Page-ins
    0 B    Page-outs
Diagnostics Information: ℹ️
    Mar 31, 2015, 07:59:25 PM    Self test - passed

Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
    b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.
5. Reinstall Yosemite from Scratch:
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

WiFi ( 802.1x EAP TTLS PAP ): Unable to connect since 2.3.3 update

I previously posted this on the Motorola Owner's Forum and am still waiting for a fix or at least an official confirmation of the problem.
Ever since the 2.3.3 update, I have been unable to connect to the wireless network at work. The connection worked fine prior to the update. The connection at home with WPA still works fine.
The network status cycles through the following sequence:
Scanning...
Connecting to <network>...
Obtaining IP address from <network>...
Disconnected
The corporate configuration is as follows:
Security: 802.1x
EAPEAP method: TTLS
Phase 2 authentication: PAP
CA certificate: (unspecified)
User certificate: (unspecified)
Use proxy server: (unchecked)
When I go into Manage Networks and select Modify network for the configuration, I find that Phase 2 authentication always shows None. If I change it to PAP and then click Save, the setting does not stick: the next time I check the configuration, it is None.
I've done a factory reset. I've configured the network settings with WiFi Advanced Configuration Editor. I've configured the network settings with WiFiConfig Editor Pro. All to no avail.
Please help. I need to be able to connect to the corporate network. If there is a known issue, it would be nice if someone would at least confirm it. Thank you.

My original Droid actually worked with the Andriod 2.0 release, but 2.1 broke it and it hasn't worked since. I believe the Android codebase DID fix this, however Verizon has not made it a priority to include the fix in their releases. I now have a Droid 4 running 2.3.6 and it is still broken. Many of my coworkers have this same issue, but ONLY THE ONES ON VERIZON! Other carriers have apparently figured out how to port this fix into their releases, regardless of which Android phone.
Come on Verizon, fix this so we can stop wasting your 4G bandwidth!!!

Extremely slow speed when backing up onto Airport Extreme disk

I have a wireless network set up with the Network Extreme basestation. The basestation has a 500 GB iomega drive attached via the USB 2.0 port. The disk comes up just fine, but when I try to use it as a backup disk from my iMac using SuperDuper!, I get an effective peak copy speed of 1.9 MB/s, and it takes multiple hours to perform a ~30 GB backup. The disk is Mac formatted.
For comparison, if I plug the disk directly into the USB port on my iMac, the peak effective speed is ~15 MB/s and the backup takes 35 min.
The iMac and the basestation are both running 802.11n, with an effective speed of 130 MB/s.
On the off chance that it was the disk imaging process that was slowing things down, I have run SuperDuper! with disk imaging back to the iMac's HD rather than the Airport Extreme HD and it runs at ~20 MB/s.
To review:
- Trying to backup to the Airport disk runs really, really slowly and takes forever
- It's not the network speed, the HD speed or the software.
What's up? Anyone else have this problem? One of the reasons I bought the Airport Extreme was to use it as a network back-up HD. If it going to take a day to copy a full iMac disk, then this is clearly unsatisfactory.

I would echo Glyn's assessment. One needs to keep in mind that Apple designed this product as a low cost device to meet the typical requirements of a home user (ie streaming of music, sharing of a few files, and backups without time constraints). If one needs the performance levels typical of a network file server, then this is the wrong product to use. Perhaps Apple's marketing information for this device should make that a bit clearer.

Extremely slow speed for around 2 months (since up...

Hi,
We've been dealing with a ridiculously slow broadband speed ever since BT informed us they were doing an upgrade. It has got continually worse and drops out throughout the day. It was never the speed it should have been anyway, but it was more reliable.
ADSL line status
Connection information
Line state
Connected
Connection time
0 days, 8:08:39
Downstream
283 Kbps
Upstream
888 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.3
Latency type
Interleaved
Noise margin (Down/Up)
15.4 dB / 11.4 dB
Line attenuation (Down/Up)
36.5 dB / 20.9 dB
Output power (Down/Up)
0.0 dBm / 13.0 dBm
Any help would be much appreciated, we've tried ringing but it's never been any help.

Sorry didn't realise there were more:
ADSL line status
Connection information
Line state
Connected
Connection time
0 days, 8:19:00
Downstream
283 Kbps
Upstream
888 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.3
Latency type
Interleaved
Noise margin (Down/Up)
15.5 dB / 11.5 dB
Line attenuation (Down/Up)
36.5 dB / 20.9 dB
Output power (Down/Up)
0.0 dBm / 13.0 dBm
Loss of Framing (Local)
0
Loss of Signal (Local)
0
Loss of Power (Local)
0
FEC Errors (Down/Up)
142905360 / 4294967264
CRC Errors (Down/Up)
824 / N/A
HEC Errors (Down/Up)
N/A / 0
Error Seconds (Local)
1
We are connected to the master socket, we don't have others. I've tried the test, just sounded crackly to me!

Extremely slow speeds

For the past month i've had extremely low download speeds, causing lots of hassle and annoyance. Ive stuck with it hoping that it was just a phase and thought BT may have been doing something with the line or whatever but yet nothings changed.
Ive done all the checks required but they still havent changed anything so thought id come here and ask. The router is plugged in to the main socket and has had the filtered changed a couple of times to make sure etc. My typical download speeds used to be around 400kbs but are now around 20kbs.
Heres my router stats:
ADSL line status
Connection information
Line state Connected
Connection time 7 days, 3:27:10
Downstream 280 Kbps
Upstream 440 Kbps
ADSL settings
VPI/VCI 0/38
Type PPPoA
Modulation ITU-T G.992.3
Latency type Interleaved
Noise margin (Down/Up) 30.8 dB / 21.5 dB
Line attenuation (Down/Up) 43.5 dB / 23.7 dB
Output power (Down/Up) 0.0 dBm / 13.2 dBm
and the speedtester results:
BT Wholesale Broadband Performance Test
Broadband Speed Test Results
Download Speed (Mbps) 0.08
Upload Speed (Mbps) 0.10
Ping Latency (ms) 0.00

Hi Samyo,
I can take a look at your connection. Please could you send me in your details using the "Contact Us" link found in my profile?
Thanks
PaddyB
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

Extremely slow speeds on EAP-TTLS PAP secured network

Similar Messages

Maybe you are looking for