Fail to established ipsec with Blackberry playbook

ASA fail to established connection with Blackberry Playbook, but when using Cisco client to test the connection established....pls help...Thanks in advance... The playbook error is " Failed to established connection. (Timeout)".
Logs when connecting through playbook...and the configuration....
ip local pool Playbook_pool 192.168.104.220-192.168.104.225 mask 255.255.255.0
access-list nonat extended permit ip 192.168.110.0 255.255.255.0 192.168.104.0 255.255.255.0
access-list nonat extended permit ip 192.168.100.0 255.255.255.0 192.168.104.0 255.255.255.0
access-list nonat extended permit ip 192.168.101.0 255.255.255.0 192.168.104.0 255.255.255.0
access-list nonat extended permit ip 192.168.111.0 255.255.255.0 192.168.104.0 255.255.255.0
access-list nonat extended permit ip 10.10.21.0 255.255.255.0 192.168.104.0 255.255.255.0
group-policy playbook_vpn_group internal
group-policy playbook_vpn_group attributes
vpn-idle-timeout 30
vpn-session-timeout 480
vpn-tunnel-protocol IPSec
ipsec-udp enable
tunnel-group playbook_users_group type remote-access
tunnel-group playbook_users_group general-attributes
address-pool Playbook_pool
authentication-server-group SecurID
default-group-policy playbook_vpn_group
tunnel-group playbook_users_group ipsec-attributes
pre-shared-key *
crypto ipsec transform-set AES_SHA esp-aes esp-sha-hmac
crypto dynamic-map PlayBookusers 2 set transform-set AES_SHA
crypto dynamic-map PlayBookusers 2 set security-association lifetime seconds 28800
crypto dynamic-map PlayBookusers 2 set security-association lifetime kilobytes 4608000
crypto map q9OutsideMap 45 ipsec-isakmp dynamic PlayBookusers
crypto isakmp policy 45
authentication pre-share
encryption aes
hash sha
group 5
lifetime 28800
BLACKBERRY PLAYBOOK CONFIG:
profile: profile1
server address: outside IP address
gateway type: Cisco asa
authentication type: XAUTH-PSK
group username: playbook_users_group
group pwd: shared key as same as in asa tunnel-group
username: username
pwd: rsa secure ID
automatically detrmine ip: checked
automatically determine DNS: checked
IKE DH Group: 2
IKE Cipher: Aes (128-bit-key)
IKE Hash: SHA1
IKE PRF: HMAC
IPSec DH Group: 2
IPSec Cipher: AES(128-bit-key)
IPSec Hash: SHA1
IKE lifetime(seconds): 28800
IPSec lifetime(seconds): 3600
NAT keepalive(seconds): 30
DPD frequesncy(seconds): 240
Disable banner: checked
use HTTP proxy: unchecked

Hi there,
At this point in time, this feature is not available on the BlackBerry PlayBook, only on your BlackBerry smartphone.
I hope this info helps!
If you want to thank someone for their comment, do so by clicking the Thumbs Up icon.
If your issue is resolved, don't forget to click the Solution button on the resolution!

Similar Messages

I used to be able to email photos from my Lightroom software quite successfully. I needed to change my password several days ago in my gmail account. Now when I try to email photos I receive a message saying "Failed to establish connection with the outgoi

I used to be able to email photos from my Lightroom software 5.7 for MAC quite successfully. I needed to change my password several days ago in my gmail account. Now when I try to email photos I receive a message saying "Failed to establish connection with the outgoing email server. Please make sure you have entered the email account and password correctly."
I have been trying to get help from Adobe for 3 days. I have sent a message through "Get Support", 2 days ago, but no one has contacted me. I have tried by phone, but no one will help me. When I purchased Lightroom in May, 2014, I was able to receive phone help. I am now told that I don't qualify because I am not a Creative Cloud customer. I have been assigned a case number 186291729.
PLEASE HELP ME FIX THIS PROBLEM

I, too, have this problem. I see no one is responding with a solution? Hello? Can someone please advise?
Oh, and, yes, I have manually verified repeatedly that the information I gave to Lightroom is correct, and I still get the same error message when I try to validate.

SQL Server Reporting services. failed to establish connection with project server. verify the url is correct.

Dear All,
I'm working on reporting of Project Server 2010, while configuring SQL SERVER REPORTING SERVICES faced issue after two complete days of troubleshooting along with this gone through plenty of forums, unable to figure out any solution. So finally posting on
technet in order to find solution.
ISSUE/PROBLEM:
At initial configured the SQL REPORTING CONFIGURATION to sharepoint integrated database (SQL SERVER is installed on seperate machine), change the service to Domain Account and also installed sharepoint add in on server story was fine at this point. Furthur
moving to SHAREPOINT ADMIN console and while configuring the Sharepoint Integrated Reporting continuously facing this error:
Failed to establish connection with report server. . . . (Snapshot is attached for your further reference).
My point of concern is that whenerver i try to open the REPORT SERVER URL on project server machine it prompts me to enter username and password but whenever i insert the domain credentails it didnt accept though it can be accesible by using the credentials
of Local Admin of sql server machine. So i wana come to know whether its permission issue if yes then where i should mention the domain credentials.?
REGARDS DANISH DANIE

Dear Paul,
I am able to open the URL (http://psdb/ReportServer )using
domian credential and page open with these contents
Reporting Services Error
The configuration parameter SharePointIntegrated is set to True but Share Point Object Model cannot be loaded
Second,
Configured the SPN on domain controller , performed the steps required to change the AUTHENTICATION in rsreportserver.config
file also done the registry settings to disable the loop back settings.
Same error still ! .... what should i do now ???
REGARDS DANISH DANIE

Failed to Establish Connection With SQL Database Server in Essbase studio

I am using Essbase Studio Release 11.1.2.1.00 for developing XOLAP cubes and deploying them on to Essbase server .
I am getting the below Error while deploying the cube onto Essbase server.
error : Failed to deploy Essbase cube.
Caused by: Failed to build Essbase cube dimension: (TimeHierarchy) .
Caused by: Cannot get async process state. Essbase Error(1021001): Failed to Establish Connection With SQL Database Server.
From Essbase Studio -> Datasources tab, I could able to connect to SQL Database server..Please let me know how to resolve this issue.
Thanks,
Swathi

Thanks for the reply.
There was a problem with my Essbase Server..so now i m pointing to other server.
now I am getting the below Error:
Failed to deploy Essbase cube.
Caused by: Cannot end incremental build. Essbase Error(1025008): Join Specification near [[TIMEID]] is invalid. Please verify the Xolap Schema file.
Please let me know how can I validate my cube and what changes might require in my Cube definitions?

Failed to Establish Connection with SQL Database Server (EAS)

Hi,
We have recently installed version 11.1.2.1 of essbase. Everything is working just peachy. One of my users tried to build a load rule using an Oracle ODBC data connection and gets the error:
Failed to Establish Connection with SQL Database Server. See log for more information.
When I look in the log I see this:
[Tue Feb 28 09:14:43 2012]Local/Sample/Basic/mressler@EnCanaAD/4240/Info(1013091)
Received Command [SQLListDsn] from user [mressler@EnCanaAD]
[Tue Feb 28 09:14:43 2012]Local/Sample/Basic/mressler@EnCanaAD/4240/Info(1021020)
Cannot read SQL driver name for [Backup Exec Catalogs] from [ODBC.INI]
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Info(1013091)
Received Command [SQLRetrieve] from user [mressler@EnCanaAD]
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Info(1021020)
Cannot read SQL driver name for [Backup Exec Catalogs] from [ODBC.INI]
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Info(1021004)
Connection String is generated
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Info(1021041)
Connection String is [DSN=Test;UID=...;PWD=...;]
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Info(1021006)
SELECT Statement [SELECT '1' from dual] is generated
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Info(1021013)
ODBC Layer Error: [IM004] ==> [[Microsoft][ODBC Driver Manager] Driver's SQLAllocHandle on SQL_HANDLE_ENV failed]
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Info(1021014)
ODBC Layer Error: Native Error code [0]
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Error(1021001)
Failed to Establish Connection With SQL Database Server. See log for more information
[Tue Feb 28 09:15:03 2012]Local/Sample/Basic/mressler@EnCanaAD/5228/Warning(1080014)
Transaction [ 0x140002( 0x4f4cfd87.0x7b890 ) ] aborted due to status [1021001].
I have tested that the ODBC connection can connect to the database. The sql query has been dumbed down to select '1' from dual. I have not included the word "select" in the query.
Anyone seen this before? We are in the process of uninstalling the Oracle client completely and re-installing it to see if this solves the issue. We only installed the 64 bit version of the Oracle client. I am running on Windows Enterprise 2008 R2 - 64 bit. EAS, Essbase, EIS are all 64 bit installs. I believe Studio is the only one that is 32bit. However we are not currently using this product.
Thanks,
Mike

Hi Mike,
With Oracle Support's help, we got 3 of the 5 servers working now. We were using the Datadirect drivers but were configuring them wrong! You have to use the Standard Connection portion in the setup, specifying the Host, Port Number (1521) and the SID. We were using the TNSNames Connection which worked in the past, but apparently does not now.
So I am down to 2 servers not working. They are both Windows 2008 R2 Enterprise 64 bit, running Oracle EPM Essbase 11.1.2.1. When I Open SQL in EAS it prompts for database (Essbase Server, App, DB) and when I hit ok it pops up with "Network error: Cannot Locate Connect Information For []". We did not do any of the suggestions in the document you linked to get the other 3 servers working. When you hit ok on that error, you then get another error stating, "There are no Data Sources defined. 'SQL data sources' option will be disabled". We do have datasources defined on the server.
Any ideas?
Thanks,
Mike
Edited by: Mike on Mar 1, 2012 8:38 AM

Essbase Error(1021001) Failed to Establish Connection With SQL Database...?

Hi there!
I am very new in Essbase and I am receiving the error message quoted below while trying to load data in a Cube. Weird thing is that we have checked all connections already and they are working correctly, however this process is still failing.
If someone can give us an idea to troubleshoot it, that would be really appreciated.
Thanks very much in advance for any help and regards!
MAXL> deploy data from model 'Production_GL_Cube_SchemaModel' in cube schema '\Production_GL\Cube_Schemas\Production_GL_Cube_Schema' login AdminUserAccount identified by MyPassword on host 'ServerName.MyCompany.com' to application 'ORA_HFM' database 'GL' overwrite values using connection 'ServerName' keep all errors on error ignore dataload write 'E:\Logs\DataLoad_Error_2013.04.19.16.23.00.txt';
BPM Connect Status: Success
Failed to deploy Essbase cube. Caused by: Failed to load data into database: GL. Caused by: Cannot get async process
state. Essbase Error(1021001): Failed to Establish Connection With SQL Database Server. See log for more information
BPM maxl deployment ...failure.

Hi Celvin,
Thanks for your reply and my apologies for not coming back before on this issue.
For the benefit of other readers, after hours struggling with the issue, we focused our attention in the following portion of the ORA_HFM.log file:
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/54996/Info(1013157)
Received Command [Import] from user [Service_Acct@Native Directory] using [GL.rul] with data file [SQL]
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Info(1021041)
Connection String is [DRIVER={DataDirect 6.1 Oracle Wire Protocol};Host=MyEssbaseServer01.MyCompany.com;Port=1521;SID=PRODUCTION;UID=...;PWD=...;ArraySize=1000000;]
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Info(1021006)
SELECT Statement [SELECT cp_127."ACCT" AS "Accounts_CHILD",
         cp_127."PERIOD_MEMBER" AS "Period_CHILD",
         cp_127."PERIOD_YEAR" AS "Years_CHILD",
         'INPUT' AS "View_CHILD",
         cp_127."ENTITY" AS "Entity_CHILD",
         cp_127."PRODUCT_LINE" AS "Custom1_Product_CHILD",
         cp_127."Function" AS "Custom4_Function_CHILD",
         cp_127."B_U" AS "Business_Unit_ORACLEBUSINESS",
         cp_127."ORACLEFUNCTION" AS "Oracle_Function_CHILD",
         cp_127."LEGALENTITY" AS "Oracle_Entity_CHILD",
         'P' || cp_127."PRODUCTLINE" AS "Oracle_Product_CHILD",
         'A'[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Info(1021043)
Connection has been established
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Info(1021044)
Starting to execute query
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Info(1021013)
ODBC Layer Error: [S1000] ==> [[DataDirect][ODBC Oracle Wire Protocol driver][Oracle]ORA-04063: view "REP_ESSBASE.VW_GL_BALANCES" has errors]
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Info(1021014)
ODBC Layer Error: Native Error code [4063]
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Error(1021001)
Failed to Establish Connection With SQL Database Server. See log for more information
[Sat Apr 20 11:48:34 2013]Local/ORA_HFM/GL/Service_Acct@Native Directory/8964/Error(1003050)
Data Load Transaction Aborted With Error [1021001]
Then we concentrated in the following error message: *ODBC Layer Error: [S1000] ==> [[DataDirect][ODBC Oracle Wire Protocol driver][Oracle]ORA-04063: view "REP_ESSBASE.VW_GL_BALANCES" has errors]*
So, we checked the database and noticed the schema and their views were damaged and -due to this- they lost all their properties (like data types, for example). So, we had to recompile all of them in order to avoid any loss of data. This was done in TOAD, as per the following info: https://support.quest.com/SolutionDetail.aspx?id=SOL66821
Finally, once all the views on this schema were rebuilt and fixed, we were able to deploy the Cube again.
Hope this help in the future. Cheers!!

Error: 1021001 Failed to Establish Connection With SQL Database Server

Hello,
Someone you already MEETS it the following error during an essbase retrieve DLR.
My client oracle essbase on my server is 64bit, Essbase 11.1.2.2 x64
I run the odbc located in% windir% \ system32 \ odbcad32.exe
"Error: 1021001 Failed to ESTABLISH Connection With SQL Database Server. See log for more information"
Here is the log:
Received Command [SQLListDsn] from user [admin]
[2:50:33 p.m. Fri 28 September 2012] Local / CAS_TEST / / / 8168/Info (1042059)
Connected from [10.100.50.2]
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Info (1013091)
Received Command [SQLRetrieve] from user [admin]
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Info (1021004)
Connection String is generated
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Info (1021041)
Connection String is [DSN = TEST_ORACLE; UID = ...; PWD = ...]
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Info (1021006)
SELECT Statement [SELECT from dual;] is generated
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Info (1021013)
ODBC Layer Error: [IM004] ==> [[Microsoft] [ODBC Driver Manager] Driver's SQLAllocHandle we failed SQL_HANDLE_ENV]
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Info (1021014)
ODBC Layer Error: Native Error code [0]
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Error (1021001)
Failed to ESTABLISH Connection With SQL Database Server. See log for more information
[2:50:33 p.m. Fri 28 September 2012] Local/CAS_TEST/CAS_TEST/admin/8168/Warning (1080014)
Transaction [0x780001 (0x50659d19.0xc9e78)] aborted due to status [1021001].
When I try to go through OCI service name:
dbServerName: port / service_name
I have the following error message:
Solutions2: List of members 1423.CAS_TEST.CAS_TEST September 28, 2012 2:50:15 PM CEST Succeeded
Read SQL record September 28, 2012 2:50:35 PM CEST Failed
thank you in advance
Edited by: 851398 on 28 sept. 2012 06:31

In essbase logs there is nothing special, same for windows log.
Everything I like is log in log view eas
[Fri Sep 28 17:52:11 2012]Local/CAS_TEST///4020/Info(1013205)
Received Command [Get Database Info]
[Fri Sep 28 17:52:11 2012]Local/CAS_TEST///4020/Info(1013205)
Received Command [Get Database State]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7580/Info(1013210)
User [admin] set active on database [CAS_TEST]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///6720/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/6720/Info(1013091)
Received Command [GetAttributeNameSpecs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7304/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7304/Info(1013091)
Received Command [GetOtlInfo] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7572/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7572/Info(1013091)
Received Command [OtlQueryMbrs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///8116/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/8116/Info(1013091)
Received Command [OtlQueryMbrs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7384/Info(1013210)
User [admin] set active on database [CAS_TEST]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///6592/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/6592/Info(1013091)
Received Command [GetAttributeNameSpecs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7972/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7972/Info(1013091)
Received Command [GetOtlInfo] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///216/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/216/Info(1013091)
Received Command [OtlQueryMbrs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///3104/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/3104/Info(1013091)
Received Command [GetAttributeNameSpecs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///3472/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/3472/Info(1013091)
Received Command [GetOtlInfo] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///8112/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/8112/Info(1013091)
Received Command [OtlQueryMbrs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///4020/Info(1013205)
Received Command [Get Database Info]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///3840/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/3840/Info(1013091)
Received Command [GetAttributeNameSpecs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7760/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7760/Info(1013091)
Received Command [GetOtlInfo] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7300/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7300/Info(1013091)
Received Command [OtlQueryMbrs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7904/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7904/Info(1013091)
Received Command [OtlQuerySmartLists] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///3612/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/3612/Info(1013091)
Received Command [GetAttributeNameSpecs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///6732/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/6732/Info(1013091)
Received Command [GetOtlInfo] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7576/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7576/Info(1013091)
Received Command [OtlQueryMbrs] from user [admin]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST///7268/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:21 2012]Local/CAS_TEST/CAS_TEST/admin/7268/Info(1013091)
Received Command [OtlQueryMbrs] from user [admin]
[Fri Sep 28 17:52:27 2012]Local/CAS_TEST///7556/Info(1013210)
User [admin] set active on database [CAS_TEST]
[Fri Sep 28 17:52:29 2012]Local/CAS_TEST///8168/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:29 2012]Local/CAS_TEST/CAS_TEST/admin/8168/Info(1013091)
Received Command [SQLListDsn] from user [admin]
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST///7564/Info(1042059)
Connected from [10.100.50.2]
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Info(1013091)
Received Command [SQLRetrieve] from user [admin]
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Info(1021004)
Connection String is generated
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Info(1021041)
Connection String is [DSN=TEST_ORACLE;UID=...;PWD=...;]
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Info(1021006)
SELECT Statement [SELECT * from dual ] is generated
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Info(1021013)
ODBC Layer Error: [IM004] ==> [[Microsoft][ODBC Driver Manager] Driver's SQLAllocHandle on SQL_HANDLE_ENV failed]
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Info(1021014)
ODBC Layer Error: Native Error code [0]
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Error(1021001)
Failed to Establish Connection With SQL Database Server. See log for more information
[Fri Sep 28 17:52:55 2012]Local/CAS_TEST/CAS_TEST/admin/7564/Warning(1080014)
Transaction [ 0xb50001( 0x5065c7d7.0x31ce0 ) ] aborted due to status [1021001].
Have you an idea about the Merant driver to essbase?
Thank

Essbase Studio Error(1021001): Failed to Establish Connection With SQL Data

Hi.
I have trying to deploy a cube with Essbase Studio but I get the error: "*Error(1021001): Failed to Establish Connection With SQL Database Server*"
My environment is Linux 5, Oracle 11g and EPM 11.1.1.2. Oracle database and Essbase was installed with diferent users. In the .bash_profile of hypadmin user (that install Essbase) I have set the following variables
ORACLE_BASE=/u01/app/oracledb/product/11.1.0
ORACLE_HOME=$ORACLE_BASE/db_1
LD_LIBRARY_PATH=/usr/X11R6/lib:$ORACLE_HOME/lib:$LD_LIBRARY_PATH
ORACLE_HOSTNAME=devbi.sigfe2
PATH=$ORACLE_HOME/bin:$ORACLE_HOME/jdk/bin:$ORACLE_HOME/bin:/sbin:$ORACLE_HOME/opmn/bin:$PATH
ORACLE_SID=orcl
JAVA_HOME=/u01/app/installfiles/jdk1.5.0_19
In my pc (windows xp) I can open Essbase Studio console, do the connection to Oracle database, get tables and create minischema, mesures and hierarchies (I can see the preview of hierarchies). Also I can create cubes with EAS and can connect with MAXSHELL to essbase.
When I try to deploy the cube from Essbaes Studio y get the error "Error(1021001): Failed to Establish Connection With SQL Database Server".
The Essbase Studio Log File say:
+12:40:16 07/24/09 (admin-1) INFO Start creating outline in database "5.4.0.41:1423.POC_ESS.POC_ESS1"...+
+12:40:16 07/24/09 (admin-1) FINA Sign on Essbase by CSS token "5.4.0.41:1423" successfully...+
+12:40:16 07/24/09 (admin-1) INFO Start building dimension "DM_CIUDADES" ...+
+12:40:16 07/24/09 (admin-1) MÁS FINA Start creating rule file ...+
+12:40:16 07/24/09 (admin-1) INFO SQL statement has been created and put into rule file "/home/hypadmin/hyperion/products/Essbase/EssbaseStudio/Server/./ess_japihome/data/DM_CIU.rul"+
+12:40:16 07/24/09 (admin-1) INFO The query is "SELECT (CONCAT('reg_',CAST(cp_105."ID_REGIONPADRE" AS VARCHAR2(1000)))) as "REGION_PADRE", (CONCAT('reg_',CAST(cp_105."ID_REGION" AS VARCHAR2(1000)))) as "REGION_HIJO", cp_105."DE_REGION" as "REGION_HIJO.Default" FROM "POC"."DM_REGIONES_ESS3" cp_105 ORDER BY cp_105."DE_NIVEL" ASC, cp_105."ID_REGIONPADRE" ASC, cp_105."ID_REGION" ASC"+
+12:40:16 07/24/09 (admin-1) INFO Rule file has been created and saved as "/home/hypadmin/hyperion/products/Essbase/EssbaseStudio/Server/./ess_japihome/data/DM_CIU.rul"+
+12:40:16 07/24/09 (admin-1) FINA Essbase starts to add members to DM_CIUDADES dimensioin based on the rules file.+
+12:40:16 07/24/09 (admin-1) ADVERTENCIA (1021001): Error al establecer conexión con el servidor de bases de datos SQL. Consulte el registro para obtener más información.+
+12:40:16 07/24/09 (admin-1) ADVERTENCIA essbaseDriver.FailedToBuildDimensionException+
+12:40:16 07/24/09 (admin-1) GRAVE Unexpected exception in EssbaseExport prevented cube from being deployed+
-------------- Exception --------------
com.hyperion.cp.datasources.export.essbase.EssbaseDriverException: Failed to deploy Essbase cube
Thanks in advance to all that have any idea to help me to solve this issue.
A.S.

Hi,
If you type database SID in lowercase, try to reenter iot in uppercase. Strange, but I and my colleagues encounter this behaviour many times.

Essbase Studio - Failed to Establish Connection With SQL Database Server

Hi all,
I am new to Hyperion and am having trouble deploying what seems a simple cube in Essbase Studio.
My environment is Windows 2003, EPM 11.1.1.2, SQL Server 2000.
I have the following two issues which may be related.
1. The EPM System Diagnostic tool says that Hyperion Foundation cannot connect to the SQL database.
Error:
Failed: Connection to database
Error: java.net.UnknownHostException: <server name: <server name>
Recommended Action:
Every other EPM application is able to connect to the database. I have tried re-configuring Foundation Services and checking the config files and nothing looks wrong. I would appreciate advice on how to fix this.
2 In Essbase Studio, I was able to connect to the database where the source data is, build the minischema and create dimensions and measures. But when I run the cube deployment wizard I get the error:
Message: Failed to deploy Essbase cube
Caused By: Failed to build Essbase cube dimension: (Time)
Caused By: Cannot incremental build. Essbase Error(1021001): Failed to Establish Connection With SQL Database Server. See log for more information
…ODBC Layer Error: [08001] ==> [[Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]SQL Server does not exist or access denied.]
I have checked the DSN as well as the connections set up within Studio, and they are all able to connect to the database. I am using the admin user for the Essbase server and have created a different user for the databases where the data resides and the shared services database. I tried using the same user all the way through and this didn’t help.
Can you please advise what else I can check or change to resolve this issue.
Also, can you work in EAS with cubes that are created in Studio? I tried looking at it and I got an error that the rule file couldn’t be accessed because it was created in Studio.
After the above failures, I tried creating a cube in EIS, with mixed success. I have been able to load the members and data without errors. But when I try to view the data in the cube, I am seeing field names for the measures instead of the data itself.
...Definitely more questions than answers at this stage of my learning.
Regards
Michelle

Michelle,
I don't know if you found an answer to you question after so many months but I was hoping I could be helpful.
The issue you are experience happens often when the dimension that you are getting an error on, in this case TIME, is built from a snowflake lineage and there is a bad foreign key reference. This dimension is most like high-up in your outline build process for Essbase Studio and this prevents the build from happening usually early on.
Check your logs also. They are in Hyperion > Products > logs > essbase > essbasestudio.
You can also make your logs more verbose by setting a configuration variable in the essbase studio server.properties file but that should only be used for debugging as it really saps performance.
And, yes, you can of course edit an Essbase Studio deployed cube in EAS. However, any changes you make to the cube in EAS are subject to being wiped-out upon the next Essbase Studio deployment of that Applicaion/Database combo.
If you want to provide more detail, screenshots, etc. I would be glad to help where I can.
Cheers,
Christian
http://www.artofbi.com

Is Photoshop Touch compatible with BlackBerry Playbook OS 2

Is Photoshop Touch compatible with BlackBerry Playbook Operating System 2.xxx ? OS 2.0 could run Android App.

Adobe PhotoShop Touch is currently available on any Android-tablet with Android OS 3.2 and higher and on Apple iPad (2nd generation or later) with iOS 5.0 or later.

Failed to Establish connection with SQL Server

hi I have configured odbc settings and when i connect the sql from essbase i got the error :Failed to Establish connection with SQL Server .please hepl me on this
and please give me step by step process for how to resolve thi issue.and give me detail step by step from starting onwards.
appreciate your Help,
Thank u
Subbu.

Steps:
1. Test database connection from Essbase server through SQL Command. This gives you whether you are able to connect to Database from Essbase server.
2. Create ODBC Connection: System DSN>Add>Select correct driver (Oracle in ...) >give Datasource (any name), Description (Any), TNS Service Name (user SID name), User name (Database user name)
3. Test Connection. if successful, you can use this ODBC to get the data.
4. Open rules file, go to FILE>Open SQL
5. Provide Essbase server, Application, Database names
6. Select SQL Data Source from the list (ODBC defined in step2)
7. Enter tested SQL Query(which is tested at SQL command or "sysdate from dual" ) in select box. NOTE: Remove select word from query. You can ignore from and where clauses, all you can include in select block.
8.Click OK/Reteive data
Rao

A total beginner with Blackberry Playbook

Hello
Someone got me a Blackberry Playbook, I certainly accepted the gift even though I wasn't sure what one of these was!
However since i got it, I am struggling to connect to wifi?> How can i fix this problem?. I have phoned up the support line which isnt much use,
I cant get past the connecting to wifi screen?
Without me sounding stupid.
Do you need to have this playbook plugged in at home near a computer?. Or is it portable? For example, can i take this round with me anywhere i go?
Or do i need to be near a wifi connection, totally confused havent got a clue whats going on
If anyone can help me (and boy i need help )> that would be great
If someone could also tell me how the playbook works what it does? i really dont have a clue!

Greetings and welcome to the community support forums!
Here are some links to help you setup and use your Playbook and learn more about it.
http://us.blackberry.com/support/tablets/playbook/get-started.html
That will help you connect to WiFi.
You don't need to be connected to a PC to use the Playbook, but if you need to be connected to the internet, you will need a Wifi connection, unless your model is a 4g model which connects over the air though a SIM card to your mobile network.
After reviewing the link above, come back and feel free to ask specific questions!
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Issues with Blackberry Playbook not being recognised by Windows Explorer

Hello, I'm new to the forums but am having the same problems as many others are, that being my Playbook not regonised by Windows Explorer. I have tried all of the solutions I have read like unistalling Desktop Manager, uninstalling then re-installing drives in Windows Device Manager. But one I recently stumbled across was uninstalling Blackberry Device Manager, how do I do this?
Also the main problem appears to be that my Playbook will not sync anything with my computer. In Desktop Manager I can back-up my Playbook, but not sync anything. After re-installing a drive I now get the message of: 'Your Blackberry device is not compatible with this feature' whereas before I got the message of: 'You haven't configured any sync methods' but yet all of the sync options were greyed out.
How do I get Windows Explorer to recognise my Playbook as a drive and how can I sync in Desktop Manager?
Thanks in advance!
Note: I'm using Windows 7 32-Bit

Hello Tobster_,
The following article should also help with detecting your BlackBerry® PlayBook™ tablet:
Identifying and troubleshooting issues with the BlackBerry Desktop Software detecting a USB connected BlackBerry PlayBook - http://www.blackberry.com/btsc/KB27424
We hope this helps.
Thank you.
-FB
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click "Accept as a Solution" for posts that have solved your issue(s)!

ICloud sync?! with Blackberry playbook, Outlook 2011 on Macbook Mountain Lion?

I have a Blackberry playbook and a macbook air moutain lion. All my calendars are in icloud that sync with my iphone and ical fine. But how can i get my icloud to sync with my blackberry. i tried sync it with outlook using my yahoo account then sync blackberry with outlook, but because of my mountain lion i couldn't sync my iphone to outlook. and i tried to sync my icloud with my gmail then to blackberry but couldn't add it.
Any suggestions?

More Like This --------------------------------------->

Using Mac 10.4.11 with Blackberry Playbook

hello everyone
is there any way that i can use my playbook with my powerpc imac 10.4.11
pleas any help would be grate seeing as i am very poor and just spent everything i had on this playbook only to find out i cannot sync it to my mac!
It would have been able to find this out prior to purchasing my playbook but i guess there is a sucker born every minute and so far my experience with Blackberry SUCKS!

Assuming that the Mac isn't a G3, you only need to purchase a newer Mac OS X version on DVD(10.5 for PowerPC Macs and 10.6 for Intel Macs.) Mac OS X 10.6 is free for paid MobileMe members.
A MacBook is an Intel Mac.
(66678)

Fail to established ipsec with Blackberry playbook

Similar Messages

Maybe you are looking for