Failed bios update: p67a-gd55 wont turn back on

Hello,
I tried to update my BIOS from version 1.J (I think) to 4.3 to get my new r9 280x to work. I used an USB stick and everything seemed to be working until the second reboot. Now it just tries to restart. All the lights turns on and the fans starts to spin and after a second it shuts down. It just repeats that until I turn off the PSU.
What are my options here? I'm quite the noob. Any help would be much appreciated!
Right now theres only one stick of 2gb RAM, an i5 2500k, a XFX 6950 and a SSD plugged in.

Quote from: biuro74 on 12-September-14, 04:14:46
I'm not MSI worker
Almost no one around this forum is, at least not me 
But I think you're right that appropriate reading would be useful. Sometimes reading twice is needed.
I remember flashing BIOS myself.. read instructions few times before flashed it.

Similar Messages

  • Every time I Try to update my iPhone it shuts of and wont turn back on

    So every time i update my iPhone it shuts of and wont turn back on, I have to drive to this friend of mine and fix it.
    But i can never update it.
    Can anyone help ? :)

    sounds like servers are way overloaded with everyone updating
    it is a large update and wwill take a lot of time (took me over 1 hour at 4AM this morning)
    keep trying from a good internet connection with your phone on a power supply

  • I was updating to ios7 and my phone turned off and now it wont turn back on. it shows the apple sign but it slowly fades away and so on. Help!

    i was updating to ios7 and my phone turned off and now it wont turn back on. it shows the apple sign but it slowly fades away and so on. Help!

    Hello there, RFJA2211.
    The following Knowledge Base article offers up some great troubleshooting steps for unexpected power off of your iOS device:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • How to Roll Back a Failed BIOS Update for my HP Compaq 6735s (467826R-999) Notebook

    I have searched the community and HP pages for instructions to uninstall a BIOS Update in case it fails, and I haven't found the procedure.
    My notebook is an  HP Compaq 6735s (467826R-999) running the Windows 7 64 bit Professional SP1, and a BIOS revision level of HP "68GPP F.0E, 09/14/09".  
    Going to the Drivers/Downloads for this notebook 
    http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=3687622&spf_p...
    I can see my old F.0E of 9/14/09 is super old because there is the F.21 dated 30-Jul-2012, GREAT!!    I just have to be sure I can recover from a (possible) failed BIOS Update.  
    Oh yeah, one more thing:  I'm not sure of the differences between the HPQFlash, the ROM Image, and the ROMPaq listed rows in the link above.  Which should I run?
    Thank you for your efforts!

    Were your suggestions assuming that I had already run a BIOS update?  I have not.  I'm just trying to be sure that I can recover from a failed attempt!  I plan to run the BIOS update on 9/20/13.
    So, when I follow your suggestion of Restart, then "F2", my notebook goes into a System Diagnostics menu.
    I spent some time in the F10, BIOS Setup, Maintenance screens but didn't find any option to RollBack.  Again, I suppose it is because I'm running the original, F.0E version!
    I also checked the link
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c02693833
    you provided to Restore your BIOS, and the tips didn't work for me - at least not with the original version installed.
    If I do take the plunge, which would you recommend:  
    HPQFlash
    ROM Image
    ROMPaq 
    Thank you!

  • Wifi turns off when connected to mobile card, but wont turn back on

    I have a Sprint wireless internet card.  When I connect to the mobile card, the Wifi radio turns off.  I'm fine with it turning off while I'm connected to the mobile card, but the problem is that it wont turn back on when I disconnect the mobile card.  If I try to use the button or other basic on/off switches in windows to turn it on, they wont respond.  The only way I can get it back on is to run a troubleshoot, which shows that the radio is disabled and asks if I want to apply the fix that will turn it back on.
    I'm on a Toshiba Satellite A665-S5170, Windows 7 (64), in the U.S.
    Thank you.

    Hi
    So does this also happen if you dont connect the notebook to external monitor? So you can determine what is causing this problem.
    If the notebook doesnt shut down without external monitor you should try to update the BIOS and display driver. Both updates you can find on the Toshiba website:
    http://eu.computers.toshiba-europe.com => Support & Downloads => Download Drivers
    Do you close the lid if you have connected the external monitor?
    What OS are you using?
    Furthermore it would be interesting to know how you cleaned the notebook. Therefore I use compressed air spray that can blow out the dust from the cooling ventilators and you must not disassemble the notebook.
    Bye

  • Bricked x120e -- failed BIOS update

    Hi,
    I was trying to update the BIOS of my x120e (0596-2RU) from within Windows 7, it got stuck (no progress for more than half an hour), now the notebook is bricked (the screen won't turn on; there's no beeps, just the fan is turned on).
    I believe I followed all the instructions (battery fully charged etc.), but the Customer Support here in Ireland says failed BIOS updates are not covered by warranty (contrary to what some people on these forums say).
    What are my options now?
    Thanks a lot!
    Solved!
    Go to Solution.

    Hi rufus82,
    I came across this thread that has answers for questions similar to the one you raised. Hope its of help.
    http://forum.lenovo.com/t5/W-Series-ThinkPad-Laptops/Bios-Update-Fail-Under-Warranty-but-No-Support/...
    As suggested by andyP, do contact support one more time.
    regards
    lak_sg
    WW Social Media
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Curve 8520 crashed and wont turn back on

    my blackberry froze yesterday and came up with a white screen so i took the battery out to reset it and now it wont turn back on. it comes up with the loading bar but gets 3/4 of a way through and turns off. iv left it off all night and tried again this morning and its still doing the same thing. is there anyway it can be fixed?

    maybe you must update your blackberry OS, because your blacberry looks crash in their system
    I give you link for fix this problem
    http://supportforums.blackberry.com/t5/Desktop-Software-for-PC/How-to-upgrade-BlackBerry-OS/td-p/748...

  • IPhone 5 screen wont turn back on after making a call.

    When I put my phone to my ear, the screen turns black, like it should, but once I'm done, it wont turn back on... It does the same thing with siri. I active the raise to speak option and the screen turns black when I do it. I then have to press the sleep button two times to get to my lock screen. Is this an hardware or a software problem? If it is software, can an upcoming update fix it?

    I don't beleive this is a known problem and you should probably bring your phone to a local Genius Bar (make an appointment here) as this is likely a hardware issue (a problem with your phone realizing that you removed it from your ear).
    If you're willing to tinker with it a bit, you can determine if this is a software issue by backing up your iPhone (separately ensure your photos, videos and music is backed up) and then "Restore" your phone. If the restoration solves the problem, you're dealing with a software issue. If the problem still exists, you're almost definitely dealing with a hardware issue.

  • I have a imac g3 dv se, snow and after about 10minutes of it booting it makes a popping sound and the turns off, then it wont turn back on for another 5-10 minutes

    i have a imac g3 dv se,500mhz, snow and after about 10minutes of it booting it makes a popping sound and the turns off, then it wont turn back on for another 5-10 minutes any suggestions?

    Actually sounds like classic symptoms of a failing PAV (power-analog-video) on that model. Historically that's the weak spot in the G3 iMacs.
    The lack of active cooling in the G3 iMac puts a lot of heat stress on this board and they eventually fail from overheating. Right now the board is still working as long as it's cool--it only fails when temps inside the computer rise.
    About the only way to preserve the computer's life is to mount a 120mm fan directly on the case where the handle is--that's the exhaust port. The fan has to be positioned to PULL air out through that vent. It's an ugly solution to the eye but it has been done around here more than you would think.
    Also make certain the bottom of the computer is not blocked. It the computer is sitting on a tablecloth or placemat, or there are loose papers on the desk under the case, it cannot get enough air into the bottom-mounted air intakes. Make/find some blocks to set the iMac a minimum of one inch (2.5CM) from the desk and move anything that can be "inhaled" from under the computer.
    Even with such measures, the PAV board will eventually fail and be unrecoverable. It's a good time to start saving for a newer computer.

  • Wont turn back on

    iphone4 wont turn back on after trying to install the most recent6.1 update, what do I do?

    Do a reset. Hold the sleep/wake and home button together until you see the Apple logo and then release. The phone will reboot.

  • HT1688 my phone was fully charged and suddenly shut off but wont turn back on

    my phone was fully charged and suddenly shut down and wont turn back on

    Hi there,
    I would recommend taking a look at the troubleshooting steps for unexpected power off issues found in the article below. 
    iPhone: Hardware troubleshooting
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Issue not resolved
    My issue is still not resolved. What do I do next?
    Contact Apple Support.
    -Griff W.

  • My phone 5 died and now it wont turn back on or seem to charge at all. I've tried several different charger cords and outlets. And all the phone will do is show the empty battery symbol. please help! Any suggestions are apprecaited!?! thanks

    My phone 5 died and now it wont turn back on or seem to charge at all. I've tried several different charger cords and outlets. And all the phone will do is show the empty battery symbol. please help! Any suggestions are apprecaited!?! thanks

    Hello Cooper,
    Thank you for the details of the issue you are experiencing with your iPhone 5.  I would be concerned too if my iPhone was not powering on.  I found an article with steps you can take when you encounter an issue like this.  I recommend following the steps below:
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    My issue is still not resolved. What do I do next?
    Contact Apple Support.
    You can find the full article here:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • I just recently purchased my macbook pro about two months ago and just now right after i turned it on it shut off and it wont turn back on or even charge. it was fully charged this morning. What happened?

    I purchased my macbook pro about two months ago. I had no issues with it what so ever. This morning i took it off the charger because it was fully charged because it showed the green light. When i came back home i turned my computer back on , entered my password and it shut off . i tried turning it back onbut it wont turn back on and neither woul it charge . Its not turning on and its not charging.

    Welcome to Apple Support Communities
    It looks like the logic board has failed, but first try a SMC reset > http://support.apple.com/kb/HT3964
    If it does not work, take the MacBook Pro to an Apple Store or reseller. You will get the MacBook repaired for free

  • HT201412 i updated my i pad 4th gen with ios 8 when the upload finished it kept turning itself off a few weeks later i did a update and now wont turn on i have tried to restore and recover but freezes any suggestions thanks Rick

    Hi i have a ipad 4th gen i updated to ios 8.0 after it installed it kept turning itself off. A few weeks later i installed a update for ios it turned itself off and wont turn back on. I have tried  plugging it into itunes to restore it recognizes the ipad when i press recover it just freezes and wont restore or recover its just a blank screen there is no power light or anything just blank please help with any suggestions, Thanks Rick.

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                     
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Satellite M40: Is failed BIOS update covered by warranty?

    Hello,
    I own a satellite M40. I had some problem with it, and tried to update the bios to see if it could solved it.
    I flash the bios with the windows based utility, but the computer shutted down without any warning.
    Now the notebook power up only 1s or 2, and then power off.
    I bought this Toshiba, 10 months ago. So, is a failed bios update outside of the warranty ?
    Thank you

    Hello,
    There is one last thing you can try if you want before taking it to your ASP. If you have a usb floppy drive, download the traditional BIOS update for your computer and ready the floppy. Once it is ready, plug the floppy to the computer. Hold down the TAB key and power on the notebook (some models have this safety feature in case of failed bios update) and see if the LEDs start blinking green and orange. If so, then it is updating the bios, once they are steady, then it is done and you can try turning it on normally again. If it does not work, then its time to take it to your ASP.

Maybe you are looking for