Failed to revert to VSS snapshot on the virtual hard disk '\\?\Volume{0f7b010b-f397-11e0-a76b-002655db9b10}\' of the virtual machine | Using HYPER-V 2008 R2

Hi,
I got this error on one of the VM (web server) backed up usng HYPER-V 2008 R2 and when I looked up, there is an microsoft hotfix for the same issue.
Microsoft KB Hotfix:
A backup of virtual machines fails when you use the Hyper-V VSS writer to back up virtual machines concurrently on a computer that is running Windows Server 2008
http://support.microsoft.com/kb/971394
But, the VM (web server) is running Windows 2008 R2 - SP1.
Hotfix says - To apply this hotfix, your computer must be running one of the following operating systems:
Windows Server 2008
Windows Server 2008 Service Pack 2 (SP2)
Does it mean it does not apply to Windows 2008 R2 | SP1 ?
When I checked the :
Swprv.dll version, it was higher than the one mentioned in the hotfix.
Thanks for any help.
-Ashwin

Hi Ashwin,
I am assuming that the VM(web server) is using SQL .
Please try to disable SQL Server VSS Writer in services.msc , then retry WSB again .
Hope this helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Similar Messages

Help - The chain of virtual hard disks is corrupted

I took a snapshot of a VHD that I tried to expand to 40GB. After expanding I tried to restart the VM but got the error that "The Chain of virtual hard disks is corrupted".
Apparently because I expanded the Parent VHD it threw up this error ( i assume because the snapshot differed in size?)
This led me to Vhdtool which I ran: vhdtool.exe /repair parentvhdfile.vhd snapshotvhdfile.vhd /quiet
This appeared to have run okay. However when I went to restart the VM again I got the error:
Servername Failed to start
Microsoft emulated IDE controller failed to power on with error - the chain of virtual hard disks is corrupted. There is a mismatch in the virtual sizes of the parent virtual hard disk and differencing disk.
Failed to open virtual disks. The size of the vurtua;l disk is not valid.
etc...
I notice that my parent VHD = 40GB in size, whilst the Snapshot (avhd) file = 109K
I think I need your help, I don't know what to do!!

If you made changes to the parent drive, your chain will be corrupted. Changes to the parent disk invalidate all the child disk.
Do you have a backup of the original parent disk?

What is the best hard disk replacement for my notebook?

Hi, what hard disk replacement should i buy for my notebook HP G62-a016sl, considering the price/quality ratio? I would not want to spend more than 60 euros/dollars.
(if you want to know why i need it, see this post: http://h30434.www3.hp.com/t5/Notebook-Recovery/Creating-and-using-a-Factory-Recovery-Disk-of-a-simil...
I'd would like to know an expert opinion. Thanks!)
This question was solved.
View Solution.

I finally got the second hard disk you recommended and i can confirm that the problem of the jerkily computer was the hard disk (almost failed) and not software. Thank you very much!

HT201250 i am using for first time the time machine and an external hard drive because I want to erase my macbook and start from zero files. do i keep my files in the portable hard disk when I connect it again with the macbook or the time machine will era

i am using for first time the time machine and an external hard drive because I want to erase my macbook and start from zero files. Am i keeping my files in the portable hard disk when I will connect it again with the macbook or the time machine will erase all?
I would like to know if after I erase all my data, empy hard drive inside the macbook, the time machine will erase all my files that I have saved in my "WD "My passport" external hard drive

Welcome to Apple Support Communities
Time Machine has to erase the external disk in order to make backups. Before setting Time Machine up, copy the files of your external disk to the hard disk of the Mac in order not to lose them, and then, set up Time Machine. The first backup will start automatically.
If you want more information about Time Machine, read the Pondini's site > http://pondini.org

Upgraded to 10.10.3, the external hard disk keep working and spinning after I ejected successfully, and the HHD keep lights up, feel unsafe to unplug it

I tried on two macbook air, same situation.
This never happen on 10.10.2 or previous version. (The HDD light will off and it will stop running after I ejected before.)
I feel unsafe to unplug the external hard disk when its still light up and running.
I am using Macbook book air 2012 and 2013 with seagate backup plus....
Anyone have same problem? how to fix it?
or its ok to unplug the HDD while the HDD light is still on and running?
MacBook Air, OS X Yosemite (10.10.3)

I have a G-Tech external hard drive that continues to spin after I have unmounted it and if I disconnect it while it is spinning it makes a very nasty sounding clunk noise. In my case it started doing this after I enabled FileVault a couple of years ago. I have found that if I unmount it and then wait 6 minutes it will stop spinning. It is inconvenient but I only use it once a week and the clunk sound is scary enough that I put up with the wait.

Windows XP SP2 did not find the bootcamp hard disk

after making the windows partition ( 32 GB) with boot camp ( version 2) assistant, I restart my Macbook ( hard disk is a SSD drive from Intel X-25 M) with my Windows Xp install cd. The drivers are loaded but at the end when we have to choose which hard disk to choose, Windows tells me he cannot find any hard disk.
when I return to the installed Mac OS X 10.5.6, I can see both my Mac hard disk and the bootcamp hard disk.
It seems that Mac OS does the work properly, but the drivers to enter the Windows set up are not loaded.
Any one has a suggestion to resolve this?

please integrate intel ahci driver into your xp cd using winlite program.

HP Envy 17, Win 7 64 Bit - How do I re-install windows when the old hard disk has failed?

The laptop wont start up and the hard disk fails the diagnostic start-up tests. Restore doesn't work and taking the hard disk out the laptop & connecting to my desktop I can't access the recovery partition. The laptop is out of warranty.
I have a replacement disk drive but as I have no install disks and the recovery partition can't be accessed how do I reinstall the OEM win 7 on the new hard disk?
Any help would be appreciated.
This question was solved.
View Solution.

If the complete 25 character windows activation key is visible on the Microsoft Windows COA on your notebook, you can download an identical iso file from here and install Windows.
Download the drivers from the HP web support portal for your notebook. Put them on a usb flashdisk (thumbdrive) for ease of installation.
Use the Microsoft Windows 7 USD\DVD download tool and a 4GB usb flashdisk (thumbdrive) for the fastest and most reliable means of installing Windows.
This way you can have your laptop in a useable state while you wait for your ordered recovery disk set.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

A problem was encountered opening a virtual hard disk in the chain of differencing disks -- when try to import vm in hyper v

Hi All,
I am new to the hyper V stuff. I have managed to install hyper-V on Windows 8. Now I am trying to import VM which got three foleders and one file batch file
Snapshots
Virtual Hard Disks
Virtual Machines
VM-Pre-Import 10961A-LON-CL1 (Batch file)
but I am getting this error
Please help me.
Thanks

Hi Tom,
Thanks for giving me direction. I am student and totally new to this hyper-v, so bit slow in understanding right now
This is the location of the files when i had extracted from rar file
Directory of C:\Program Files\Microsoft Learning\10961\Drives\10961A-LON-CL1
06/13/2014 07:54 AM    <DIR>          .
06/13/2014 07:54 AM    <DIR>          ..
03/16/2013 12:05 AM    <DIR>          Snapshots
06/13/2014 07:25 AM    <DIR>          Virtual Hard Disks
06/13/2014 06:25 AM    <DIR>          Virtual Machines
03/15/2013 07:38 PM               135 VM-Pre-Import-10961A-LON-CL1.bat
               1 File(s)            135 bytes
               5 Dir(s) 477,346,160,640 bytes free
when I opened the bat file -- location of the file
SET SUBDIR=%~dp0
mklink "%SUBDIR%Virtual Hard Disks\Base12B-W8.vhd" "C:\Program Files\Microsoft Learning\Base\Base12B-W8.vhd"
pause
and then i have changed the dir path to
SET SUBDIR=%~dp0
mklink "%SUBDIR%Virtual Hard Disks\Base12B-W8.vhd" "C:\Program Files\Microsoft Learning\10961\Drives\10961A-LON-CLI\Base12B-W8.vhd"
pause
When I tried to run the batch file then I got following message -- Can't creat a file when that file already exists.
Please advise

Unable to make tWo concurrent logins to the firewire Hard Disk from RHEL 3.

Hello
I tried setting up a firewire(shared storage) ORACLE 10 G RAC CLUSTER using OCFS/ASM using your install guidelines
but this failed.Below is the scenario.
Hardware : compaq intel PC's with 1 GB RAM
Members in the cluster : Two
Operating system : RHEL AS 3 / FEDORA CORE -3 (both being tried one after the other)
Oracle 10G RAC version : 10.1.0.3.0
HDD : Maxtor one touch II 250 GB with combo interface Firewire/USB 2.0
N/W Adapters : Two public interconnect,Two private interconnect thru 10/100 internet Hubs/switches
Firewire card details: FireWire (IEEE 1394): Agere Systems (former Lucent Microelectronics) FW323 (rev 05)
Failure Description
I successfully loaded the drivers for the Maxtor one touch II in the two Linux (RHEL 3) boxes. But after a restart, at any point of time,
the disk is detected only by one node. It is detected in the other node only if the first node is powered OFF. On investigating we found the
following error message by running "dmesg | grep sbp2" command as root
ieee1394: sbp2: Query logins to SBP-2 device successful
ieee1394: sbp2: Maximum concurrent logins supported: 2
ieee1394: sbp2: Number of active logins: 1
ieee1394: sbp2: Error logging into SBP-2 device - login failed
Please do suggest where i was wrong and how to proceed next.
Thanks & Regards
Raghavan

Hello All,
I work as the system admin for Raghavan. Thanks to all those who took time to reply to our queries. Sorry for the lengthy mail. Let me go through the whole sequence of what we did initially.
1. Installed RHEL 3 with Agere PCI Firewire cards.
2. Installed Firewire Kernel kernel-2.4.21-27.0.2.ELorafw1 on top of it.
3. Modules were loaded properly and the Firewire hard disk was accessible from both the nodes.
4. Everything went fine during OCFS and ASM installation.
5. We were installing the CRS and that too went fine till 99% and the final step of running the root.sh in one of the nodes gave an error message as follows
"Failure at final check of Oracle CRS Stack
0"
6. So we thought of reinstalling CRS and deleted the Voting disk file directly from the shared disk. We deleted the file manually from one of the nodes using the "rm -rf" command and that too before uninstalling OCFS.
Now both the disks went out of sync. The voting disk and CRS file was still visible from the other node. So we did a reboot of both the nodes one by one. After this MYSTERIOUS reboot at any point of time only one node was able to detect the hard disk.
Finally after nearly two months of head scratching (really lost lot of my hair in this :)) we were able to get concurrent logins from both the nodes now! Thanks to the reply by Member no 279089. I bought and installed a TI(TSB43AB23)card on one node and a VIA chipset card on the other. And finally the magic worked. I am able to partition the disk and the partitions are visible from both the nodes.
But now we have a new problem. When we invoke the OCFSTOOL from one node (VIA card node), the previous OCFS partion (the one which was done before the MYSTERIOUS reboot) is still shown. I removed the /etc/ocfs.conf file and still it is being shown in the ocfstool. I tried to ignore this and continued creating the OCFS partition from the other node (TI card node) using the mkfs.ocfs command. That too ran fine without any error messages and was able to mount it under /u02/oradata/orcl. When I try to mount the partition from VIA card node it is giving me the following error
# mount -t ocfs /dev/sdb1 /u02/oradata/orcl
mount: wrong fs type, bad option, bad superblock on /dev/sdb1, or too many mounted file systems
I get the following in /var/log/messages
Jun 29 21:16:40 testrac1 kernel: SCSI disk error : host 2 channel 0 id 0 lun 0 return code = 8000000
Jun 29 21:16:40 testrac1 kernel: Current sd08:11: sense key None
Jun 29 21:16:40 testrac1 kernel: I/O error: dev 08:11, sector 69
I tried googling with the above error message and they seem to point hands towards VIA chipsets. But I am not sure. Please guide us on what needs to be done to resolve this issue if you have faced it before.
Thanks in Advance
Jei

Error adding VM through Powershell: Virtual hard disk in the chain of differencing

I'm trying to programmatically create a VM from a .vhd file - my code is below. I'm getting a weirdo file not found error about disk chaining, but I've TRIPLE checked all my paths. Help is much appreciated!!!
Thanks,
Error:
ADD-VMHardDiskDrive : 'Testing' failed to add device 'Virtual Hard Disk'. (Virtual machine ID ADC7CF7D-2EC5-4428-B27C-6EDCF29F5922)
Failed to open virtual disk 'E:\will\VMTesting\Flash.480x800.vhd'. A problem was encountered opening a virtual hard disk in the chain of differencing
disks, 'E:\will\VMTesting\Flash.vhd' (referenced by 'E:\will\VMTesting\Flash.480x800.vhd'): 'The system cannot find the file specified.' (0x80070002).
My PowerShell code:
$n = "Testing";
$directory = "E:\will\VMTesting";
$vhdxPath = "$directory\$n.vhdx";
$vhdPath = "$directory\Flash.480x800.vhd";
$vm = Get-VM $n;
if($vm -ne $null) { Remove-VM $n -Force; }
New-VM -Name $n -MemoryStartupBytes (Invoke-Expression "1000MB") -Path $directory;
Set-VMMemory -VMName $n -DynamicMemoryEnabled $true -MinimumBytes 512MB -MaximumBytes 4096MB -StartupBytes 2048MB -Buffer 20;
ADD-VMHardDiskDrive -VMName $n -Path $vhdPath;
Start-VM $n;

Hi Will ,
According to the error message , please try to check the chain of differencing disk via "inspect disk.." .
# Create our New Differencing Disk
New-VHD –ParentPath T:\02R2June2012\08R2TemplateJune2012.vhdx –Path T:\lab50\lab50-PSDiffDiskVM\lab50-PSDiffDiskVM.vhdx -Differencing
For creating a differencing disk please refer to following link:
http://lyncdup.com/2012/06/creating-hyper-v-3-differencing-disks-in-server-2012-with-gui-and-powershell/
Hope this helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

HT201269 I am trying to save memory on my iPhone 4S/ ios6. Can I back up all photos to icloud and the external hard disk I normally use for photos? If I then delete photos from the iPhone do the get deleted on iCloud?

I am trying to save memory on my iPhone 4S/ ios6.
1) Can I back up all photos to icloud and the external hard disk I normally use for photos? If I then delete photos from the iPhone do the get deleted on iCloud?
2) Can I back up the newsstand to iCloud and save memory on the iPhone?
3) Can I back up the bookshelf to icloud and save memory on the iPhone?

1. What format is the external drive? It sounds like it's ina format that Macs can't write to. Is it a NAS or NTFS?
2. Easiest thing: just move your iPhoto Library to the external
Make sure the drive is formatted Mac OS Extended (Journaled)
1. Quit iPhoto
2. Copy the iPhoto Library from your Pictures Folder to the External Disk.
3. Hold down the option (or alt) key while launching iPhoto. From the resulting menu select 'Choose Library' and navigate to the new location. From that point on this will be the default location of your library.
4. Test the library and when you're sure all is well, trash the one on your internal HD to free up space.
Regards
TD

K8neo 4 socket 939 cpu 3800 x2 amd what is the best hard disk

k8neo 4 socket 939 cpu 3800 x2 amd what is the best hard disk
for this confy
i know maxtor has more problem
so i ask to you
what is the best hard disk 250 300 gb ?
sata sata 2 ?
i read about in some site but i can understand what is the best for this confy
thank
my english is Lol

When we are talking about Quality and Performance the choice is:
http://www.wdraptorx.com

Creating a Master virtual hard disk and using the same for all other VM's

Hi,
We would like to create a master virtual hard disk and use the same for all other VM's. Can we do that ?
my requirements :
1) create 10 VM's
2) first create a master virtual hard disk with win OS and use the same to create the 10 VM's.
3) After creating the VM's change the HDD size.
              -- if i have created master virtual disk with 500GB , and use the same for creating a virtual machine. can we change the HDD size to 1TB ?
After creating the VM's ,i will change the system names and activate the windows accordingly.
Will there be any implications ,if we can/will do like this.
Thanks.

Hi Suren424,
I think Using Differencing Disks may cover your needs .
Please refer to following setps:
   "Create the Parent Virtual Machine Configuration and Virtual Hard Disk
    Install the Operating System, updates, and common software
    Generalize the installation
    Prepare the parent virtual hard disk
    Create the differencing disks
    Create virtual machines that use the differencing disks
For details please refer to follwing link:
http://social.technet.microsoft.com/wiki/contents/articles/1393.hyper-v-virtual-machine-vm-parent-child-configuration-using-differencing-disks.aspx
Hope this helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

The server encounter an error while attaching Virtual Hard Disk in Windows Server 2008R2

Unable to add an existing virtual hard disk in new VM(windows server 2008r2).

Please repost here:
https://social.technet.microsoft.com/Forums/windowsserver/en-US/home?forum=winserverhyperv
And include the actual and full error message.

Error (23317) The operation Change properties of virtual machine is not permitted on a virtual machine that has shared virtual hard disks. Recommended Action The operation Change properties of virtual machine is not permitted on a virtual machine that h

Experts !
Error (23317)
The operation Change properties of virtual machine is not permitted on a virtual machine that has shared virtual hard disks.
Recommended Action
The operation Change properties of virtual machine is not permitted on a virtual machine that has shared virtual hard disks.
Is this limitation by design? If we have a shared VHDX between two VMs, then I am not able to change the VM properties from SCVMM.
SCVMM 2012 R2 with Windows Server 2012 R2 Hyper-V.
Appreciate any help !
Optimism is the faith that leads to achievement. Nothing can be done without hope and confidence.
InsideVirtualization.com

Hello,
that is a VMM issue.
If you did not deploy your virtual cluster from a VMM service template, VMM doesn't recognize the configuration.
Until MS got it fixed, you could use the workaround from system center central:
http://www.systemcentercentral.com/tag/shared-vhdx/
This posting is provided >AS IS< with no warranties.

Failed to revert to VSS snapshot on the virtual hard disk '\\?\Volume{0f7b010b-f397-11e0-a76b-002655db9b10}\' of the virtual machine | Using HYPER-V 2008 R2

Similar Messages

Maybe you are looking for