Failed to start up - blank screen!

Yesterday, when I turn on my mac the grey screen appeared but the wheel doesn't. So when 10 minutes passed and nothing happened I turn it off from the power button. After some minutes I tried to turn it on again but at this time nothing appeared but only a blank screen neither sound chime and the keyboard didn't correspond. I checked the keyboard to another mac and it's ok! What's going on? I have poor knowledge in hardware.

Pull the battery and test that. Pull the hard drive. See if you get the old "?" on startup. A corrupt hard drive can in some cases prevent booting even from any CD/DVD or alternal hard drive.
While in there, find the PMU would be next step.
If a system won't boot into Open Firmware (command option o f) I think you are close to sunk.

Similar Messages

IMac starts with blank screen

Hello,
My iMac has been acting a little weird lately, until last night, when it got much worse. It's a 2009 iMac running Mavericks.
Every so often when I would turn it on, it would give the Apple chime and the screen would never come on, it would remain blank. I would try restarting a couple of times and it would typically fire right up, Apple chime and the screen would come to life. Last night, I was updating iTunes and a couple other things and my iMac restarted. Except that it did the blank screen thing on restart. Now, I can try restarting it for ten minutes before the screen actually comes to life, but when it does, it goes right back to trying to install updates. After the updates are done installing, the computer restarts itself... And the cycle continues.
It's pretty much stuck in a loop of start-update-restart-blank screen. It won't boot up correctly two consecutive times, no matter how many times I try.
Any advice?

Check System Preferences - Startup Disk and see if your internal HD is highlighted. If it is not please click it and then select restart.

Satellite A105-S4164 - won't start only blank screen

Hi all,
I have a Toshiba Satellite A105-S4164 laptop that won't start.
I thought that perhaps there is a problem with the battery. I took the battery out and then hooked up the laptop to the electrical outlet, made no difference. The blue lights in front the laptop, come on, but I don't hear any noise from the mother board or the fan. The laptop is purchased in July of 2006 and it is out of warranty.
All I see is the blank screen.
My guess is that the mother board must be replaced. I also had kept up with Symantic Anti virus and also windows XP upgrades prior to April 1, 2009.
Thank you for your feedback.
Seyed

Can you see a picture on an external monitor?
Well I think in this case the notebook should be checked by notebook technician. You should contact an ASP and ask for help. This would be the best way because the technician can make sure what parts are faulty.
http://eu.computers.toshiba-europe.com => Support & Downloads => Find an authorized service provider

Equium L10 300 Wont start up Blank screen

Hi I wonder if anyone can help or advise me with a start up problem,
It's a Equium laptop L10 300 XP homedition, After running PC doctor to remove Popups and adware my laptop stopped starting up.
Initially on start up after the system check it kept returning a blue warning screen which flashed off very quickly before shutting down and trying to restart this made it very difficult to read but i managed to make out something about a physical memory issue and dump, I managed to access the safe mode options and tried each one of the options including last known good configuration but all failed to start the machine up and just returned the same error message. Then at some point with all my fiddling it now wont even run the system check before crashing it now only does the initial boot which allows me to access the BIOS system F2 and F12 and nothing more.
I have the product recovery disc and even tried it briefly before interupting it When I realised the instructions say it will reformat the drive and I will lose all my data which I dont wish to do.
Is there a way for me to repair this problem or copy extract my data, before using the product recovery disc.
Many thanks in anticipation,

First you should check the memory, it may be corrupting the data. Did you install aftermarket memory recently? Go to www.memtest.org and boot memtest from a floppy disk or CD.
To recover your data, you can remove the HDD and connect it to another PC using a 2.5" USB Adapter. Then put the HDD back in and run recovery.
ps. you can view the blue BSOD code by pressing F8 when Windows starts booting, and select "Disable automatic restart on system failure" in the Menu.

MacBook Pro 3.1 fails on start up. Screen very pixelated and says to restart.

I have an older MacBook Pro 3.1 that has worked great for a long time. On start up the screen is very pixelated and cascades to a large power button that states my computer needs to be restarted (in several languages). Any ideas as to the cause?

Your MBP has the problematic NVIDIA card which Apple had a repair program for a while:
http://support.apple.com/kb/TS2377

DOS Programs Fail To Start in Full Screen

HP 4600 WorkstationWindows XP SP3 all latest driversQuadro FX 580 Display CardDOS command line starts and works fine in Full ScreenHowever when I try to start any DOS program, either from the start menu or the command line I get an error: "ntvdm.exe has encountered a problem and needs to be closed." Error SignatureAppName: ntvdm.exe v5.1.2600.5512ModName: kernel32.dll v5.1.2600.6532Offset: 00012fd3 Exception InfoCode: 0xC0000005Flags: 0x00000001Record: 0x00000000Address: 0x000000007C812FD3 My research indicates it's an access memory violation, probably by the nVidia driver.The ntvdm creates a 16-bit virtual environment for these programs.Iv'e tried everything I can think of:-HotFixes from Microsoft-BIOS settings-turn off DEP-Google searches-different driver versions-modify PIF settings-etc, etc.-tried nVidia support with no luck Has anyone got a DOS program to start in full screen?If so then at least I will know it can be done.Any suggestions, setting changes, etc?Maybe change display card to GeForce and those drivers. I know... why use a DOS program. Well because I need to,I wouldn't be going through this hassle if I didn't. If I can'tget the DOS program to run in this computer then its onlygood as a door stop for me. Thanks

reindeer4,
> How can I make my flash site load in Full Screen mode
> by default (using Actionscript 3 in Flash CS4)?
The security features of Flash Player are specifically
configured to
keep this from happening. The idea is to avoid someone being
able to trick
the end user into thinking s/he is using a fullscreen app, or
something
other than Flash. Note, for example, that unless you're
developing for AIR,
full screen mode disables keyboard input:
http://help.adobe.com/en_US/AS3LCR/Flash_10.0/flash/display/StageDisplayState.html#FULL_SC REEN
Additional details available here:
http://help.adobe.com/en_US/AS3LCR/Flash_10.0/flash/display/Stage.html#displayState
David Stiller
Co-author, ActionScript 3.0 Quick Reference Guide
http://tinyurl.com/dpsAS3QuickReferenceGuide
"Luck is the residue of good design."

Satellite 3000-X11: Four beeps at start-up, blank screen

Hi folks,
A friend has given me a laptop to try and fix. It's a Toshiba Satellite 3000-X11.
Sometimes it works fine. Starts up like normal.
Sometimes, fairly randomly, it will not start. In this instance nothing will come up on the screen at powerup. The fan will kick in. The screen is black and there are four beeps. About 1 per second. It then sits there. On, but half dead. Can hear fan from time to time.
I've read messages on the net that suggest this is a hardware failure of some kind. What I'd like to know is if there is any easy way to know what hardware has failed. Nearly all the messages I read talked about three beeps. This is four.
Makes no diff if I am running it from AC or battery.
I have no idea what makes it start working again.
I suspect (just a suspicion) that it tends to stop working after it has been moved around (i.e. picked up and moved to another desk etc.).
Any suggestions would be appreciated.
Also, is there a Toshiba diagnostic tool I can download and run that will test the machine out?
Thanks,
Jonathan

Coincidentally, I had a similar problem last night on my old S3000 laptop. I popped out a PCMCIA card while the laptop was powered up and it just hung. I rebooted it, and I got a few series of beeps and nothing else.
After a lot of swearing. I thought I remembered something about holding down keys at power up on laptops to get them working. I powered down, pressed and held the "esc" key, then powered up. The laptop recovered, displaying a "safe boot" mode. I selected "boot from hard disk" and it seems to have been fine since...
Hopefully that might help.

Project Never Starts - Only Blank Screen

Greetings,
I've just recently upgraded to CP3.
I'd like to have an online version and a cd version of the
project so people can use either type.
When exporting the project it works fine on some computers
while others just give me a the playbar and a blank white screen.
I've had some success with .exe files on certain machines,
but not the swf/htm versions (tried online and local versions).
Any ideas why the project just won't seem to load and play?
Unfortunately, my company needs this asap and I'm running out of
answers.
Thanks,
tothebeat

Hi again
The CD Autorun failure could be the file naming. If you are
using spaces, substitute underscores. But I tend to only use the
older DOS 8.3 format for my naming.
Where are the files when you are running on other PCs? Local
C drive or on a web server? If local C drive, have you tried
copying to a web server? If web server, are you certain you copied
ALL the files up there? Often, folks miss the need to copy the
standard.js file. I didn't suggest this earlier as you said it
seems to work on some, but not all PCs. Which is what made me think
it's a Flash Player thing.
Cheers... Rick

X1 Carbon (3443CTO) start up blank screen and no activities after BIOS ACHI to Compatibility

Hi everyone,
I have a X1 Carbon 3443CTO and it's running fine.
Last night everything was ok and I went into the BIOS and changed AHCI to compatibility (don't ask me why, I was doing some testing), then I went "Exit and Save Changes" (at the last page of BIOS). As soon as I press Enter the screen freezed there (as opposed to reboot)
Since it hangs there I hold the power button and it shutdown.
Then I power it up again, but now, here is the problem:
1) The computer turns ON, keyboard backlight flash on for a second (normal)
2) Screen stays blank (no, it's not the backlight faulty)
3) power light turns ON (normal)
4) no sign of activities pressing any buttons, no beep sound
I am not sure what the problem is but it feels it's due to BIOS setting I did that caused the problem. Would someone please help me to resolve this (urgent)?
Many thanks!!!
John
Solved!
Go to Solution.

It turns out that the board does need replacement, they are ordering the part and getting it replaced.

Issue with blank screen HP G60-447CL Notebook PC

Issue with blank screen HP G60-447CL Notebook PC, I purchased warranty and have had the laptop serviced before for the same exact issue. Same problem has come up again blank screen it has been less than five months this problem was fixed and it has started again: blank screen white, laptop is powered on nothing else happens. Now I cannot reach anyone.

You're very welcome.
I have tried many times to help folks with different drivers and nothing has worked.
I'd say at least a dozen people have posted about this issue, and no one can fix it.
I don't understand it either.

Following a message saying that my Startup disc was full and advising me to delete some files, I deleted my trash but then apps started to fail. When I tried to log on again, all I got was a blank screen and a cursor. I am a Mac Book Pro virgin, help

Following a message saying that my Startup disc was full and advising me to delete some files, I deleted my trash but then apps started to fail. When I tried to log on again, all I got was a blank screen and a cursor, so I am unable to delete any more files. I am a Mac Book Pro virgin, help

How much free space do you actually have? Go to the Apple menu and select About This Mac... More Info... and click on the Storage tab. You should see something like this...
This will show you how much free space you have and what's taking up all the space on your hard drive. You may need to backup and trash some seldom used files, applications, etc. You have to drag them into the Trash and empty the trash to regain the space. A general rule of thumb is that you should have about 15% of your hard drive storage free.
Good luck,
Clinton

Blank Screen after start-up chime, won't start

I'm rather perplexed as to what's happened to my PowerBook. I'll run throught it
PowerBook 12" 1.33 768
Background:
I've just updated it to 10.4.4, which caused it to get stuck at the Apple symbol and spinning wheel. I had to restart in single user mode and run applejack, restart again and it was fine.
Recently the PowerBook started to not wake from sleep, I'd have hold down the power button then restart it. I thought it had done teh same thing today, but this time it makes the start-up chime but gets no further than a blank (dark, black) screen.
I tried inserting the Mac OS X CD and start up holding down the C key, but still same blank screen (with the added benefit that I'm now unable to remove the CD)
I tried plugging it into an external monitor, but nothing.
I've tried resetting the Preference RAM and the PMU. With some limited success. On occasion after resetting the PRAM, turning it off then back on, it starts with something like a extra blow of air from the fan and white blank screen instead of a black one. It then won't turn off at all, the only way is to pull the power and the battery.
I've noticed that when the ac adapter is plugged in and i've the white screen it flashes very quickly, orange.
I tried starting in Tartget disc mode connected to an iMac, the disc doesn't appear.
I tried starting up with an external firewire drive attached, nothing.
I've tried starting holding the keys for open firmware mode, nothing.
I've removed the AirPort card, no change.
I removed the extra 512mb RAM with no change.
The screen is clearly working, has anyone any ideas how to get it started?
Any help would be appreciated, it's a second hand PowerBook and so has no AppleCare.
Cheers
Stuart

I had the EXACT same problem happen to me, Stuartea71. My PowerBook crashed on the on Feb. 4th and I still can't figure it out. I had just dowloaded the 10.4.4 update, bought iLife 06, and ordered a new battery.
I tried every single thing that you did above. I finally called customer support, and walked me through a few things which I had already tried, but she finally pin pointed something in disk utility that I missed. My disk would not mount. In red letters it said "failing." She told me that was a internal HD problem that needs to be fixed by a certified tech.
I did something I'd never done before. I put my HD to sleep to optimize battery performance. I work with podcasts and downloaded a large file. Unfortunately I forgot my battery setting. I chalk it up as a lesson learned, and just bit the bullet and ordered a MacBook Pro.
BTW... if you all customer service they basically read directly from the Apple Website. I paid $49 dollars for someone to tell me my mac was broken and send it in.

[SOLVED] Blank screen starting new Xorg (ATI)

Yes, it's another blank screen problem with xorg. Sorry.
After months of sticking with an older Xorg (due to problems with my ATI Radeon X1550 card and the new Xorg w/ dual head), I decided to make a jump and update to the latest Xorg and ati drivers, foregoing dual screens. I've read you can just start Xorg without a config, which I tried, but no luck. I just get a blank screen. I autogenerated a config file and still get a blank screen. Either way there's no default X cursor or xterm anywhere.
I've tried adding the AllowEmptyInput flag as suggested in related threads, but that doesn't help. My .conf file and log file are listed below. If someone could give me some suggestions to solve this, I'd appreciate it.;
My xorg.conf.new file:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
Option "DontZap" "false"
Option "AllowEmptyInput" "off"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
# Load "glx"
Load "extmod"
Load "record"
Load "dri2"
Load "dbe"
Load "dri"
Load "drm"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
#DisplaySize 380 300 # mm
Identifier "Monitor0"
VendorName "ACR"
ModelName "AL1916"
HorizSync 31.0 - 81.0
VertRefresh 56.0 - 75.0
Option "DPMS"
EndSection
Section "Device"
### Available Driver options are:-
### Values: : integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "Dac6Bit" # [<bool>]
#Option "Dac8Bit" # [<bool>]
#Option "BusType" # [<str>]
#Option "CPPIOMode" # [<bool>]
#Option "CPusecTimeout" # 
#Option "AGPMode" # 
#Option "AGPFastWrite" # [<bool>]
#Option "AGPSize" # 
#Option "GARTSize" # 
#Option "RingSize" # 
#Option "BufferSize" # 
#Option "EnableDepthMoves" # [<bool>]
#Option "EnablePageFlip" # [<bool>]
#Option "NoBackBuffer" # [<bool>]
#Option "DMAForXv" # [<bool>]
#Option "FBTexPercent" # 
#Option "DepthBits" # 
#Option "PCIAPERSize" # 
#Option "AccelDFS" # [<bool>]
#Option "IgnoreEDID" # [<bool>]
#Option "DisplayPriority" # [<str>]
#Option "PanelSize" # [<str>]
#Option "ForceMinDotClock" # <freq>
#Option "ColorTiling" # [<bool>]
#Option "VideoKey" # 
#Option "RageTheatreCrystal" # 
#Option "RageTheatreTunerPort" # 
#Option "RageTheatreCompositePort" # 
#Option "RageTheatreSVideoPort" # 
#Option "TunerType" # 
#Option "RageTheatreMicrocPath" # <str>
#Option "RageTheatreMicrocType" # <str>
#Option "ScalerWidth" # 
#Option "RenderAccel" # [<bool>]
#Option "SubPixelOrder" # [<str>]
#Option "ShowCache" # [<bool>]
#Option "DynamicClocks" # [<bool>]
#Option "VGAAccess" # [<bool>]
#Option "ReverseDDC" # [<bool>]
#Option "LVDSProbePLL" # [<bool>]
#Option "AccelMethod" # <str>
#Option "DRI" # [<bool>]
#Option "ConnectorTable" # <str>
#Option "DefaultConnectorTable" # [<bool>]
#Option "DefaultTMDSPLL" # [<bool>]
#Option "TVDACLoadDetect" # [<bool>]
#Option "ForceTVOut" # [<bool>]
#Option "TVStandard" # <str>
#Option "IgnoreLidStatus" # [<bool>]
#Option "DefaultTVDACAdj" # [<bool>]
#Option "Int10" # [<bool>]
#Option "EXAVSync" # [<bool>]
#Option "ATOMTVOut" # [<bool>]
#Option "R4xxATOM" # [<bool>]
Identifier "Card0"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "RV505 [Radeon X1550 Series]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
My Xorg.0.log:
X.Org X Server 1.6.2
Release Date: 2009-7-7
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-ARCH i686
Current Operating System: Linux aina 2.6.30-ARCH #1 SMP PREEMPT Mon Jul 20 11:20:32 UTC 2009 i686
Build Date: 18 July 2009 08:27:13PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Jul 27 18:18:46 2009
(++) Using config file: "./xorg.conf.new"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) Option "DontZap" "false"
(**) Option "AllowEmptyInput" "off"
(==) Automatically adding devices
(==) Automatically enabling devices
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
built-ins
(**) ModulePath set to "/usr/lib/xorg/modules"
(II) Loader magic: 0x7a40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7
(--) PCI:*(0:1:0:0) 1002:7143:1043:01c6 ATI Technologies Inc RV505 [Radeon X1550 Series] rev 0, Mem @ 0xe0000000/268435456, 0xf5000000/65536, I/O @ 0x0000b000/256, BIOS @ 0x????????/131072
(--) PCI: (0:1:0:1) 1002:7163:1043:01c7 ATI Technologies Inc RV505 [Radeon X1550 Series] (Secondary) rev 0, Mem @ 0xf5010000/65536
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded by default.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "ati"
(II) Loading /usr/lib/xorg/modules/drivers//ati_drv.so
(II) Module ati: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 6.12.2
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "radeon"
(II) Loading /usr/lib/xorg/modules/drivers//radeon_drv.so
(II) Module radeon: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 6.12.2
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.4.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(II) RADEON: Driver for ATI Radeon chipsets:
ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
ATI Radeon 9800XT NJ (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE),
ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE),
ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
ATI Mobility Radeon X1700, ATI Radeon X2300HD,
ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
ATI Radeon 4800 Series, ATI FirePro V8750 (FireGL),
ATI FirePro V7760 (FireGL), ATI Mobility RADEON HD 4850,
ATI Mobility RADEON HD 4850 X2, ATI Radeon 4800 Series,
ATI FirePro RV770, AMD FireStream 9270, AMD FireStream 9250,
ATI FirePro V8700 (FireGL), ATI Mobility RADEON HD 4870,
ATI Mobility RADEON M98, ATI Radeon 4800 Series,
ATI Radeon 4800 Series, ATI FirePro M7750, ATI M98, ATI M98, ATI M98,
ATI Radeon RV730 (AGP), ATI FirePro M5750, ATI Radeon RV730 (AGP),
ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
ATI RV730 PRO [Radeon HD 4650], ATI FirePro V7750 (FireGL),
ATI FirePro V5700 (FireGL), ATI FirePro V3750 (FireGL), ATI RV610,
ATI Radeon HD 2400 XT, ATI Radeon HD 2400 Pro,
ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000, ATI RV610,
ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
ATI Mobility Radeon HD 3850 X2, ATI RV670,
ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
ATI Radeon RV710, ATI Radeon RV710, ATI Radeon HD 4350,
ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
ATI Mobility Radeon 4500 Series, ATI RV630,
ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
ATI FireGL V3600, ATI Radeon HD 2600 LE,
ATI Mobility FireGL Graphics Processor, ATI Radeon RV710,
ATI Radeon HD 3470, ATI Mobility Radeon HD 3430,
ATI Mobility Radeon HD 3400 Series, ATI Radeon HD 3450,
ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Radeon HD 3450,
ATI FirePro V3700, ATI FireMV 2450, ATI FireMV 2260, ATI FireMV 2260,
ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
ATI Radeon HD 3600 PRO, ATI Mobility Radeon HD 3650,
ATI Mobility Radeon HD 3670, ATI Mobility FireGL V5700,
ATI Mobility FireGL V5725, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3300 Graphics,
ATI Radeon HD 3200 Graphics, ATI Radeon 3000 Graphics,
ATI Radeon HD Graphics, ATI Radeon Graphics,
ATI Mobility Radeon HD Graphics, ATI Mobility Radeon Graphics,
ATI Radeon Graphics
(II) Primary Device is: PCI 01@00:00:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) RADEON(0): TOTO SAYS 00000000f5000000
(II) RADEON(0): MMIO registers at 0x00000000f5000000: size 64KB
(II) RADEON(0): PCI bus 1 card 0 func 0
(==) RADEON(0): Depth 24, (--) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 0.1.0
ABI class: X.Org Video Driver, version 5.0
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(--) RADEON(0): Chipset: "ATI Radeon X1550" (ChipID = 0x7143)
(WW) RADEON(0): R500 support is under development. Please report any issues to [email protected]
(--) RADEON(0): Linear framebuffer at 0x00000000e0000000
(II) RADEON(0): PCIE card detected
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 5.0
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(II) RADEON(0): ATOM BIOS detected
(II) RADEON(0): ATOM BIOS Rom:
SubsystemVendorID: 0x1043 SubsystemID: 0x01c6
IOBaseAddress: 0xb000
Filename: SV25429.bin
BIOS Bootup Message:
7143.9.13.1.29.AS01
(II) RADEON(0): Framebuffer space used by Firmware (kb): 20
(II) RADEON(0): Start of VRAM area used by Firmware: 0xfffb000
(II) RADEON(0): AtomBIOS requests 20kB of VRAM scratch space
(II) RADEON(0): AtomBIOS VRAM scratch base: 0xfffb000
(II) RADEON(0): Cannot get VRAM scratch space. Allocating in main memory instead
(II) RADEON(0): Default Engine Clock: 550000
(II) RADEON(0): Default Memory Clock: 400000
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Output: 1100000
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Input: 13500
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Input: 1000
(II) RADEON(0): Maximum Pixel Clock: 400000
(II) RADEON(0): Reference Clock: 27000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) RADEON(0): [dri] Found DRI library version 1.3.0 and kernel module version 1.30.0
(==) RADEON(0): Page Flipping disabled on r5xx and newer chips.
(II) RADEON(0): Will try to use DMA for Xv image transfers
(II) RADEON(0): Generation 2 PCI interface, using max accessible memory
(II) RADEON(0): Detected total video RAM=262144K, accessible=262144K (PCI BAR=262144K)
(--) RADEON(0): Mapped VideoRAM: 262144 kByte (128 bit DDR SDRAM)
(II) RADEON(0): Color tiling enabled by default
(II) RADEON(0): Max desktop size set to 2560x1600
(II) RADEON(0): For a larger or smaller max desktop size, add a Virtual line to your xorg.conf
(II) RADEON(0): If you are having trouble with 3D, reduce the desktop size by adjusting the Virtual line to your xorg.conf
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) RADEON(0): ref_freq: 2700, min_out_pll: 64800, max_out_pll: 110000, min_in_pll: 100, max_in_pll: 1350, xclk: 40000, sclk: 550.000000, mclk: 400.000000
(II) RADEON(0): PLL parameters: rf=2700 rd=13 min=64800 max=110000; xclk=40000
(II) RADEON(0): Skipping TV-Out
(II) RADEON(0): Skipping Component Video
encoder: 0x15
encoder: 0x13
encoder: 0x16
(II) RADEON(0): Output VGA-0 using monitor section Monitor0
(II) RADEON(0): I2C bus "VGA-0" initialized.
(II) RADEON(0): Output DVI-0 has no monitor section
(II) RADEON(0): I2C bus "DVI-0" initialized.
(II) RADEON(0): Port0:
XRANDR name: VGA-0
Connector: VGA
CRT1: INTERNAL_KLDSCP_DAC1
DDC reg: 0x7e40
(II) RADEON(0): Port1:
XRANDR name: DVI-0
Connector: DVI-I
CRT2: INTERNAL_KLDSCP_DAC2
DFP1: INTERNAL_KLDSCP_TMDS1
DDC reg: 0x7e50
(II) RADEON(0): I2C device "VGA-0:E-EDID segment register" registered at address 0x60.
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
(II) RADEON(0): EDID vendor "ACR", prod id 1916
(II) RADEON(0): Using hsync ranges from config file
(II) RADEON(0): Using vrefresh ranges from config file
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) RADEON(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) RADEON(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
(II) RADEON(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 1
(II) RADEON(0): EDID data from the display on output: VGA-0 ----------------------
(II) RADEON(0): Manufacturer: ACR Model: 77c Serial#: 1764
(II) RADEON(0): Year: 2006 Week: 13
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
(II) RADEON(0): Sync: Separate Composite SyncOnGreen
(II) RADEON(0): Max Image Size [cm]: horiz.: 38 vert.: 30
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): DPMS capabilities: Off; RGB/Color Display
(II) RADEON(0): Default color space is primary color space
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.634 redY: 0.354 greenX: 0.287 greenY: 0.621
(II) RADEON(0): blueX: 0.138 blueY: 0.077 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Supported established timings:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@67Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 832x624@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported standard timings:
(II) RADEON(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) RADEON(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 108.0 MHz Image Size: 376 x 301 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) RADEON(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) RADEON(0): Ranges: V min: 56 V max: 75 Hz, H min: 31 H max: 81 kHz, PixClock max 140 MHz
(II) RADEON(0): Monitor name: AL1916
(II) RADEON(0): ACER
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff0004727c07e4060000
(II) RADEON(0): 0d1001030e261e782e6875a25a499f23
(II) RADEON(0): 135054bfef00714f8180010101010101
(II) RADEON(0): 010101010101302a009851002a403070
(II) RADEON(0): 1300782d1100001e000000fd00384b1f
(II) RADEON(0): 510e000a202020202020000000fc0041
(II) RADEON(0): 4c313931360a202020202020000000fe
(II) RADEON(0): 00414345520a202020202020202000b1
finished output detect: 0
(II) RADEON(0): I2C device "DVI-0:E-EDID segment register" registered at address 0x60.
(II) RADEON(0): I2C device "DVI-0:ddc2" registered at address 0xA0.
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Dac detection success
Unhandled monitor type 0
finished output detect: 1
finished all detect
before xf86InitialConfiguration
(II) RADEON(0): EDID vendor "ACR", prod id 1916
(II) RADEON(0): Using hsync ranges from config file
(II) RADEON(0): Using vrefresh ranges from config file
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) RADEON(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) RADEON(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
(II) RADEON(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 1
(II) RADEON(0): EDID data from the display on output: VGA-0 ----------------------
(II) RADEON(0): Manufacturer: ACR Model: 77c Serial#: 1764
(II) RADEON(0): Year: 2006 Week: 13
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
(II) RADEON(0): Sync: Separate Composite SyncOnGreen
(II) RADEON(0): Max Image Size [cm]: horiz.: 38 vert.: 30
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): DPMS capabilities: Off; RGB/Color Display
(II) RADEON(0): Default color space is primary color space
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.634 redY: 0.354 greenX: 0.287 greenY: 0.621
(II) RADEON(0): blueX: 0.138 blueY: 0.077 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Supported established timings:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@67Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 832x624@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported standard timings:
(II) RADEON(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) RADEON(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 108.0 MHz Image Size: 376 x 301 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) RADEON(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) RADEON(0): Ranges: V min: 56 V max: 75 Hz, H min: 31 H max: 81 kHz, PixClock max 140 MHz
(II) RADEON(0): Monitor name: AL1916
(II) RADEON(0): ACER
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff0004727c07e4060000
(II) RADEON(0): 0d1001030e261e782e6875a25a499f23
(II) RADEON(0): 135054bfef00714f8180010101010101
(II) RADEON(0): 010101010101302a009851002a403070
(II) RADEON(0): 1300782d1100001e000000fd00384b1f
(II) RADEON(0): 510e000a202020202020000000fc0041
(II) RADEON(0): 4c313931360a202020202020000000fe
(II) RADEON(0): 00414345520a202020202020202000b1
(II) RADEON(0): EDID vendor "ACR", prod id 1916
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Dac detection success
Unhandled monitor type 0
(II) RADEON(0): Output VGA-0 connected
(II) RADEON(0): Output DVI-0 disconnected
(II) RADEON(0): Using exact sizes for initial modes
(II) RADEON(0): Output VGA-0 using initial mode 1280x1024
after xf86InitialConfiguration
(**) RADEON(0): Display dimensions: (380, 300) mm
(**) RADEON(0): DPI set to (85, 108)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(==) RADEON(0): Using gamma correction (1.0, 1.0, 1.0)
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(==) RADEON(0): Using XAA acceleration architecture
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.2.1
ABI class: X.Org Video Driver, version 5.0
(!!) RADEON(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
(!!) RADEON(0): MergedFB support has been removed and replaced with xrandr 1.2 support
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprU)
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprU)
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprU)
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) RADEON(0): RADEONScreenInit e0000000 0 0
Output CRT1 disable success
Blank CRTC 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC 1 success
(==) RADEON(0): Using 24 bit depth buffer
(II) RADEON(0): RADEONInitMemoryMap() :
(II) RADEON(0): mem_size : 0x10000000
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(II) RADEON(0): Depth moves disabled by default
(II) RADEON(0): Using 32 MB GART aperture
(II) RADEON(0): Using 1 MB for the ring buffer
(II) RADEON(0): Using 2 MB for vertex/indirect buffers
(II) RADEON(0): Using 29 MB for GART textures
(II) RADEON(0): Memory manager initialized to (0,0) (1280,8191)
(II) RADEON(0): Reserved area from (0,1280) to (1280,1282)
(II) RADEON(0): Largest offscreen area available: 1280 x 6909
(II) RADEON(0): Will use front buffer at offset 0x0
(II) RADEON(0): Will use back buffer at offset 0x1b80000
(II) RADEON(0): Will use depth buffer at offset 0x21c0000
(II) RADEON(0): Will use 32 kb for PCI GART table at offset 0xfff8000
(II) RADEON(0): Will use 221184 kb for textures at offset 0x2800000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) RADEON(0): [drm] Using the DRM lock SAREA also for drawables.
(II) RADEON(0): [drm] framebuffer handle = 0xe0000000
(II) RADEON(0): [drm] added 1 reserved context for kernel
(II) RADEON(0): X context handle = 0x1
(II) RADEON(0): [drm] installed DRM signal handler
(II) RADEON(0): [pci] 32768 kB allocated with handle 0xf93c5000
(II) RADEON(0): [pci] ring handle = 0xf93c5000
(II) RADEON(0): [pci] Ring mapped at 0xa765d000
(II) RADEON(0): [pci] Ring contents 0x00000000
(II) RADEON(0): [pci] ring read ptr handle = 0xf94c6000
(II) RADEON(0): [pci] Ring read ptr mapped at 0xb792c000
(II) RADEON(0): [pci] Ring read ptr contents 0x00000000
(II) RADEON(0): [pci] vertex/indirect buffers handle = 0xf94c7000
(II) RADEON(0): [pci] Vertex/indirect buffers mapped at 0xa745d000
(II) RADEON(0): [pci] Vertex/indirect buffers contents 0x00000000
(II) RADEON(0): [pci] GART texture map handle = 0xf96c7000
(II) RADEON(0): [pci] GART Texture map mapped at 0xa57dd000
(II) RADEON(0): [drm] register handle = 0x2ea00000
(II) RADEON(0): [dri] Visual configs initialized
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(==) RADEON(0): Backing store disabled
(II) RADEON(0): [DRI] installation complete
(II) RADEON(0): [drm] Added 32 65536 byte vertex/indirect buffers
(II) RADEON(0): [drm] Mapped 32 vertex/indirect buffers
(II) RADEON(0): [drm] dma control initialized, using IRQ 16
(II) RADEON(0): [drm] Initialized kernel GART heap manager, 29884416
(WW) RADEON(0): DRI init changed memory map, adjusting ...
(WW) RADEON(0): MC_FB_LOCATION was: 0xefffe000 is: 0xefffe000
(WW) RADEON(0): MC_AGP_LOCATION was: 0x003f0000 is: 0xffffffc0
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0xffffffc0
(II) RADEON(0): Direct rendering enabled
(II) RADEON(0): XAA Render acceleration unsupported on Radeon 9500/9700 and newer. Please use EXA instead.
(II) RADEON(0): Render acceleration disabled
(II) RADEON(0): num quad-pipes is 1
(II) RADEON(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Scanline Image Writes
Setting up tile and stipple cache:
32 128x128 slots
32 256x256 slots
16 512x512 slots
(II) RADEON(0): Acceleration enabled
(**) Option "dpms"
(**) RADEON(0): DPMS enabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Will use 32 kb for hardware cursor 0 at offset 0x00643000
(II) RADEON(0): Will use 32 kb for hardware cursor 1 at offset 0x00648000
(II) RADEON(0): Largest offscreen area available: 1280 x 6901
(II) RADEON(0): Set up textured video
Output CRT1 disable success
Blank CRTC 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC 1 success
Output CRT1 disable success
Mode 1280x1024 - 1688 1066 5
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0xffffffc0
freq: 108000000
best_freq: 108000000
best_feedback_div: 48
best_ref_div: 2
best_post_div: 6
(II) RADEON(0): crtc(0) Clock: mode 108000, PLL 108000
(II) RADEON(0): crtc(0) PLL : refdiv 2, fbdiv 0x30(48), pdiv 6
Set CRTC 0 PLL success
Set CRTC Timing success
Set CRTC 0 Overscan success
Not using RMX
scaler 0 setup success
Set CRTC 0 Source success
crtc 0 YUV disable setup success
Output DAC1 setup success
Enable CRTC 0 success
Unblank CRTC 0 success
Output CRT1 enable success
Blank CRTC 1 success
Disable CRTC 1 success
(II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: drmOpenMinor returns 12
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: enabled GLX_texture_from_pixmap with driver support
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/r300_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) RADEON(0): Setting screen physical size to 376 x 301
(**) Option "Protocol" "auto"
(**) Option "Device" "/dev/input/mice"
(II) Mouse0: Setting mouse protocol to "ExplorerPS/2"
(**) Mouse0: Device: "/dev/input/mice"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: always reports core events
(**) Option "Device" "/dev/input/mice"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5 6 7"
(**) Mouse0: ZAxisMapping: buttons 4, 5, 6 and 7
(**) Mouse0: Buttons: 11
(**) Mouse0: Sensitivity: 1
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(**) Mouse0: (accel) keeping acceleration scheme 1
(**) Mouse0: (accel) filter chain progression: 2.00
(**) Mouse0: (accel) filter stage 0: 20.00 ms
(**) Mouse0: (accel) set acceleration profile 0
(II) Mouse0: Setting mouse protocol to "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
(**) Option "CoreKeyboard"
(**) Keyboard0: always reports core events
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 2.2.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device ImExPS/2 Logitech Explorer Mouse
(**) ImExPS/2 Logitech Explorer Mouse: always reports core events
(**) ImExPS/2 Logitech Explorer Mouse: Device: "/dev/input/event6"
(II) ImExPS/2 Logitech Explorer Mouse: Found 5 mouse buttons
(II) ImExPS/2 Logitech Explorer Mouse: Found x and y relative axes
(II) ImExPS/2 Logitech Explorer Mouse: Found scroll wheel(s)
(II) ImExPS/2 Logitech Explorer Mouse: Configuring as mouse
(**) ImExPS/2 Logitech Explorer Mouse: YAxisMapping: buttons 4 and 5
(**) ImExPS/2 Logitech Explorer Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "ImExPS/2 Logitech Explorer Mouse" (type: MOUSE)
(**) ImExPS/2 Logitech Explorer Mouse: (accel) keeping acceleration scheme 1
(**) ImExPS/2 Logitech Explorer Mouse: (accel) filter chain progression: 2.00
(**) ImExPS/2 Logitech Explorer Mouse: (accel) filter stage 0: 20.00 ms
(**) ImExPS/2 Logitech Explorer Mouse: (accel) set acceleration profile 0
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) AIGLX: Suspending AIGLX clients for VT switch
Output CRT1 disable success
Blank CRTC 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC 1 success
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(II) RADEON(0): avivo_restore !
Enable CRTC 0 success
Unblank CRTC 0 success
(II) AT Translated Set 2 keyboard: Close
(II) UnloadModule: "evdev"
(II) ImExPS/2 Logitech Explorer Mouse: Close
(II) UnloadModule: "evdev"
(II) Macintosh mouse button emulation: Close
(II) UnloadModule: "evdev"
(II) UnloadModule: "kbd"
(II) UnloadModule: "mouse"
(II) RADEON(0): [drm] removed 1 reserved context for kernel
(II) RADEON(0): [drm] unmapping 8192 bytes of SAREA 0xf802f000 at 0xb792d000
(II) RADEON(0): [drm] Closed DRM master.
Last edited by edenxavier (2009-07-28 22:33:44)

Did like you said, however it didn't work. It complained this time about not having the fbdev available. It's not installed because I didn't think it was related. Here's the new Xorg.log.0 file:
X.Org X Server 1.6.2
Release Date: 2009-7-7
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-ARCH i686
Current Operating System: Linux aina 2.6.30-ARCH #1 SMP PREEMPT Mon Jul 20 11:20:32 UTC 2009 i686
Build Date: 18 July 2009 08:27:13PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Jul 27 23:20:52 2009
(II) Loader magic: 0x7a40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7
(--) PCI:*(0:1:0:0) 1002:7143:1043:01c6 ATI Technologies Inc RV505 [Radeon X1550 Series] rev 0, Mem @ 0xe0000000/268435456, 0xf5000000/65536, I/O @ 0x0000b000/256, BIOS @ 0x????????/131072
(--) PCI: (0:1:0:1) 1002:7163:1043:01c7 ATI Technologies Inc RV505 [Radeon X1550 Series] (Secondary) rev 0, Mem @ 0xf5010000/65536
(==) Using default built-in configuration (30 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default ati Device 0"
Driver "ati"
EndSection
Section "Screen"
Identifier "Builtin Default ati Screen 0"
Device "Builtin Default ati Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default ati Screen 0"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default ati Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default ati Device 0"
(==) No monitor specified for screen "Builtin Default ati Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (2)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "ati"
(II) Loading /usr/lib/xorg/modules/drivers//ati_drv.so
(II) Module ati: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 6.12.2
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "radeon"
(II) Loading /usr/lib/xorg/modules/drivers//radeon_drv.so
(II) Module radeon: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 6.12.2
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers//vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 2.2.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) RADEON: Driver for ATI Radeon chipsets:
ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
ATI Radeon 9800XT NJ (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE),
ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE),
ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
ATI Mobility Radeon X1700, ATI Radeon X2300HD,
ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
ATI Radeon 4800 Series, ATI FirePro V8750 (FireGL),
ATI FirePro V7760 (FireGL), ATI Mobility RADEON HD 4850,
ATI Mobility RADEON HD 4850 X2, ATI Radeon 4800 Series,
ATI FirePro RV770, AMD FireStream 9270, AMD FireStream 9250,
ATI FirePro V8700 (FireGL), ATI Mobility RADEON HD 4870,
ATI Mobility RADEON M98, ATI Radeon 4800 Series,
ATI Radeon 4800 Series, ATI FirePro M7750, ATI M98, ATI M98, ATI M98,
ATI Radeon RV730 (AGP), ATI FirePro M5750, ATI Radeon RV730 (AGP),
ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
ATI RV730 PRO [Radeon HD 4650], ATI FirePro V7750 (FireGL),
ATI FirePro V5700 (FireGL), ATI FirePro V3750 (FireGL), ATI RV610,
ATI Radeon HD 2400 XT, ATI Radeon HD 2400 Pro,
ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000, ATI RV610,
ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
ATI Mobility Radeon HD 3850 X2, ATI RV670,
ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
ATI Radeon RV710, ATI Radeon RV710, ATI Radeon HD 4350,
ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
ATI Mobility Radeon 4500 Series, ATI RV630,
ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
ATI FireGL V3600, ATI Radeon HD 2600 LE,
ATI Mobility FireGL Graphics Processor, ATI Radeon RV710,
ATI Radeon HD 3470, ATI Mobility Radeon HD 3430,
ATI Mobility Radeon HD 3400 Series, ATI Radeon HD 3450,
ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Radeon HD 3450,
ATI FirePro V3700, ATI FireMV 2450, ATI FireMV 2260, ATI FireMV 2260,
ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
ATI Radeon HD 3600 PRO, ATI Mobility Radeon HD 3650,
ATI Mobility Radeon HD 3670, ATI Mobility FireGL V5700,
ATI Mobility FireGL V5725, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3300 Graphics,
ATI Radeon HD 3200 Graphics, ATI Radeon 3000 Graphics,
ATI Radeon HD Graphics, ATI Radeon Graphics,
ATI Mobility Radeon HD Graphics, ATI Mobility Radeon Graphics,
ATI Radeon Graphics
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 01@00:00:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(WW) Falling back to old probe method for vesa
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) RADEON(0): TOTO SAYS 00000000f5000000
(II) RADEON(0): MMIO registers at 0x00000000f5000000: size 64KB
(II) RADEON(0): PCI bus 1 card 0 func 0
(II) RADEON(0): Creating default Display subsection in Screen section
"Builtin Default ati Screen 0" for depth/fbbpp 24/32
(==) RADEON(0): Depth 24, (--) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 0.1.0
ABI class: X.Org Video Driver, version 5.0
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(--) RADEON(0): Chipset: "ATI Radeon X1550" (ChipID = 0x7143)
(WW) RADEON(0): R500 support is under development. Please report any issues to [email protected]
(--) RADEON(0): Linear framebuffer at 0x00000000e0000000
(II) RADEON(0): PCIE card detected
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 5.0
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(II) RADEON(0): ATOM BIOS detected
(II) RADEON(0): ATOM BIOS Rom:
SubsystemVendorID: 0x1043 SubsystemID: 0x01c6
IOBaseAddress: 0xb000
Filename: SV25429.bin
BIOS Bootup Message:
7143.9.13.1.29.AS01
(II) RADEON(0): Framebuffer space used by Firmware (kb): 20
(II) RADEON(0): Start of VRAM area used by Firmware: 0xfffb000
(II) RADEON(0): AtomBIOS requests 20kB of VRAM scratch space
(II) RADEON(0): AtomBIOS VRAM scratch base: 0xfffb000
(II) RADEON(0): Cannot get VRAM scratch space. Allocating in main memory instead
(II) RADEON(0): Default Engine Clock: 550000
(II) RADEON(0): Default Memory Clock: 400000
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Output: 1100000
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Input: 13500
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Input: 1000
(II) RADEON(0): Maximum Pixel Clock: 400000
(II) RADEON(0): Reference Clock: 27000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) RADEON(0): [dri] Found DRI library version 1.3.0 and kernel module version 1.30.0
(==) RADEON(0): Page Flipping disabled on r5xx and newer chips.
(II) RADEON(0): Will try to use DMA for Xv image transfers
(II) RADEON(0): Generation 2 PCI interface, using max accessible memory
(II) RADEON(0): Detected total video RAM=262144K, accessible=262144K (PCI BAR=262144K)
(--) RADEON(0): Mapped VideoRAM: 262144 kByte (128 bit DDR SDRAM)
(II) RADEON(0): Color tiling enabled by default
(II) RADEON(0): Max desktop size set to 2560x1600
(II) RADEON(0): For a larger or smaller max desktop size, add a Virtual line to your xorg.conf
(II) RADEON(0): If you are having trouble with 3D, reduce the desktop size by adjusting the Virtual line to your xorg.conf
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) RADEON(0): ref_freq: 2700, min_out_pll: 64800, max_out_pll: 110000, min_in_pll: 100, max_in_pll: 1350, xclk: 40000, sclk: 550.000000, mclk: 400.000000
(II) RADEON(0): PLL parameters: rf=2700 rd=13 min=64800 max=110000; xclk=40000
(II) RADEON(0): Skipping TV-Out
(II) RADEON(0): Skipping Component Video
encoder: 0x15
encoder: 0x13
encoder: 0x16
(II) RADEON(0): Output VGA-0 has no monitor section
(II) RADEON(0): I2C bus "VGA-0" initialized.
(II) RADEON(0): Output DVI-0 has no monitor section
(II) RADEON(0): I2C bus "DVI-0" initialized.
(II) RADEON(0): Port0:
XRANDR name: VGA-0
Connector: VGA
CRT1: INTERNAL_KLDSCP_DAC1
DDC reg: 0x7e40
(II) RADEON(0): Port1:
XRANDR name: DVI-0
Connector: DVI-I
CRT2: INTERNAL_KLDSCP_DAC2
DFP1: INTERNAL_KLDSCP_TMDS1
DDC reg: 0x7e50
(II) RADEON(0): I2C device "VGA-0:E-EDID segment register" registered at address 0x60.
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
(II) RADEON(0): EDID vendor "ACR", prod id 1916
(II) RADEON(0): Using EDID range info for horizontal sync
(II) RADEON(0): Using EDID range info for vertical refresh
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) RADEON(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) RADEON(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
(II) RADEON(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 1
(II) RADEON(0): EDID data from the display on output: VGA-0 ----------------------
(II) RADEON(0): Manufacturer: ACR Model: 77c Serial#: 1764
(II) RADEON(0): Year: 2006 Week: 13
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
(II) RADEON(0): Sync: Separate Composite SyncOnGreen
(II) RADEON(0): Max Image Size [cm]: horiz.: 38 vert.: 30
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): DPMS capabilities: Off; RGB/Color Display
(II) RADEON(0): Default color space is primary color space
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.634 redY: 0.354 greenX: 0.287 greenY: 0.621
(II) RADEON(0): blueX: 0.138 blueY: 0.077 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Supported established timings:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@67Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 832x624@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported standard timings:
(II) RADEON(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) RADEON(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 108.0 MHz Image Size: 376 x 301 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) RADEON(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) RADEON(0): Ranges: V min: 56 V max: 75 Hz, H min: 31 H max: 81 kHz, PixClock max 140 MHz
(II) RADEON(0): Monitor name: AL1916
(II) RADEON(0): ACER
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff0004727c07e4060000
(II) RADEON(0): 0d1001030e261e782e6875a25a499f23
(II) RADEON(0): 135054bfef00714f8180010101010101
(II) RADEON(0): 010101010101302a009851002a403070
(II) RADEON(0): 1300782d1100001e000000fd00384b1f
(II) RADEON(0): 510e000a202020202020000000fc0041
(II) RADEON(0): 4c313931360a202020202020000000fe
(II) RADEON(0): 00414345520a202020202020202000b1
finished output detect: 0
(II) RADEON(0): I2C device "DVI-0:E-EDID segment register" registered at address 0x60.
(II) RADEON(0): I2C device "DVI-0:ddc2" registered at address 0xA0.
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Dac detection success
Unhandled monitor type 0
finished output detect: 1
finished all detect
before xf86InitialConfiguration
(II) RADEON(0): EDID vendor "ACR", prod id 1916
(II) RADEON(0): Using hsync ranges from config file
(II) RADEON(0): Using vrefresh ranges from config file
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
(II) RADEON(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) RADEON(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) RADEON(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) RADEON(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
(II) RADEON(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
(II) RADEON(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 1
(II) RADEON(0): EDID data from the display on output: VGA-0 ----------------------
(II) RADEON(0): Manufacturer: ACR Model: 77c Serial#: 1764
(II) RADEON(0): Year: 2006 Week: 13
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
(II) RADEON(0): Sync: Separate Composite SyncOnGreen
(II) RADEON(0): Max Image Size [cm]: horiz.: 38 vert.: 30
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): DPMS capabilities: Off; RGB/Color Display
(II) RADEON(0): Default color space is primary color space
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.634 redY: 0.354 greenX: 0.287 greenY: 0.621
(II) RADEON(0): blueX: 0.138 blueY: 0.077 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Supported established timings:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@67Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 832x624@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported standard timings:
(II) RADEON(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) RADEON(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 108.0 MHz Image Size: 376 x 301 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) RADEON(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) RADEON(0): Ranges: V min: 56 V max: 75 Hz, H min: 31 H max: 81 kHz, PixClock max 140 MHz
(II) RADEON(0): Monitor name: AL1916
(II) RADEON(0): ACER
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff0004727c07e4060000
(II) RADEON(0): 0d1001030e261e782e6875a25a499f23
(II) RADEON(0): 135054bfef00714f8180010101010101
(II) RADEON(0): 010101010101302a009851002a403070
(II) RADEON(0): 1300782d1100001e000000fd00384b1f
(II) RADEON(0): 510e000a202020202020000000fc0041
(II) RADEON(0): 4c313931360a202020202020000000fe
(II) RADEON(0): 00414345520a202020202020202000b1
(II) RADEON(0): EDID vendor "ACR", prod id 1916
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Dac detection success
Unhandled monitor type 0
(II) RADEON(0): Output VGA-0 connected
(II) RADEON(0): Output DVI-0 disconnected
(II) RADEON(0): Using exact sizes for initial modes
(II) RADEON(0): Output VGA-0 using initial mode 1280x1024
after xf86InitialConfiguration
(**) RADEON(0): Display dimensions: (380, 300) mm
(**) RADEON(0): DPI set to (85, 108)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(==) RADEON(0): Using gamma correction (1.0, 1.0, 1.0)
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(==) RADEON(0): Using XAA acceleration architecture
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 1.6.2, module version = 1.2.1
ABI class: X.Org Video Driver, version 5.0
(!!) RADEON(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
(!!) RADEON(0): MergedFB support has been removed and replaced with xrandr 1.2 support
(II) UnloadModule: "vesa"
(II) Unloading /usr/lib/xorg/modules/drivers//vesa_drv.so
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprU)
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprU)
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprU)
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) RADEON(0): RADEONScreenInit e0000000 0 0
Output CRT1 disable success
Blank CRTC 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC 1 success
(==) RADEON(0): Using 24 bit depth buffer
(II) RADEON(0): RADEONInitMemoryMap() :
(II) RADEON(0): mem_size : 0x10000000
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(II) RADEON(0): Depth moves disabled by default
(II) RADEON(0): Using 32 MB GART aperture
(II) RADEON(0): Using 1 MB for the ring buffer
(II) RADEON(0): Using 2 MB for vertex/indirect buffers
(II) RADEON(0): Using 29 MB for GART textures
(II) RADEON(0): Memory manager initialized to (0,0) (1280,8191)
(II) RADEON(0): Reserved area from (0,1280) to (1280,1282)
(II) RADEON(0): Largest offscreen area available: 1280 x 6909
(II) RADEON(0): Will use front buffer at offset 0x0
(II) RADEON(0): Will use back buffer at offset 0x1b80000
(II) RADEON(0): Will use depth buffer at offset 0x21c0000
(II) RADEON(0): Will use 32 kb for PCI GART table at offset 0xfff8000
(II) RADEON(0): Will use 221184 kb for textures at offset 0x2800000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) RADEON(0): [drm] Using the DRM lock SAREA also for drawables.
(II) RADEON(0): [drm] framebuffer handle = 0xe0000000
(II) RADEON(0): [drm] added 1 reserved context for kernel
(II) RADEON(0): X context handle = 0x1
(II) RADEON(0): [drm] installed DRM signal handler
(II) RADEON(0): [pci] 32768 kB allocated with handle 0xf93e3000
(II) RADEON(0): [pci] ring handle = 0xf93e3000
(II) RADEON(0): [pci] Ring mapped at 0xb77ac000
(II) RADEON(0): [pci] Ring contents 0x00000000
(II) RADEON(0): [pci] ring read ptr handle = 0xf94e4000
(II) RADEON(0): [pci] Ring read ptr mapped at 0xb799f000
(II) RADEON(0): [pci] Ring read ptr contents 0x00000000
(II) RADEON(0): [pci] vertex/indirect buffers handle = 0xf94e5000
(II) RADEON(0): [pci] Vertex/indirect buffers mapped at 0xa74dc000
(II) RADEON(0): [pci] Vertex/indirect buffers contents 0x00000000
(II) RADEON(0): [pci] GART texture map handle = 0xf96e5000
(II) RADEON(0): [pci] GART Texture map mapped at 0xa585c000
(II) RADEON(0): [drm] register handle = 0x2ea00000
(II) RADEON(0): [dri] Visual configs initialized
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(==) RADEON(0): Backing store disabled
(II) RADEON(0): [DRI] installation complete
(II) RADEON(0): [drm] Added 32 65536 byte vertex/indirect buffers
(II) RADEON(0): [drm] Mapped 32 vertex/indirect buffers
(II) RADEON(0): [drm] dma control initialized, using IRQ 16
(II) RADEON(0): [drm] Initialized kernel GART heap manager, 29884416
(WW) RADEON(0): DRI init changed memory map, adjusting ...
(WW) RADEON(0): MC_FB_LOCATION was: 0xefffe000 is: 0xefffe000
(WW) RADEON(0): MC_AGP_LOCATION was: 0x003f0000 is: 0xffffffc0
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0xffffffc0
(II) RADEON(0): Direct rendering enabled
(II) RADEON(0): XAA Render acceleration unsupported on Radeon 9500/9700 and newer. Please use EXA instead.
(II) RADEON(0): Render acceleration disabled
(II) RADEON(0): num quad-pipes is 1
(II) RADEON(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Scanline Image Writes
Setting up tile and stipple cache:
32 128x128 slots
32 256x256 slots
16 512x512 slots
(II) RADEON(0): Acceleration enabled
(II) RADEON(0): DPMS enabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Will use 32 kb for hardware cursor 0 at offset 0x00643000
(II) RADEON(0): Will use 32 kb for hardware cursor 1 at offset 0x00648000
(II) RADEON(0): Largest offscreen area available: 1280 x 6901
(II) RADEON(0): Set up textured video
Output CRT1 disable success
Blank CRTC 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC 1 success
Output CRT1 disable success
Mode 1280x1024 - 1688 1066 5
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0xffffffc0
freq: 108000000
best_freq: 108000000
best_feedback_div: 48
best_ref_div: 2
best_post_div: 6
(II) RADEON(0): crtc(0) Clock: mode 108000, PLL 108000
(II) RADEON(0): crtc(0) PLL : refdiv 2, fbdiv 0x30(48), pdiv 6
Set CRTC 0 PLL success
Set CRTC Timing success
Set CRTC 0 Overscan success
Not using RMX
scaler 0 setup success
Set CRTC 0 Source success
crtc 0 YUV disable setup success
Output DAC1 setup success
Enable CRTC 0 success
Unblank CRTC 0 success
Output CRT1 enable success
Blank CRTC 1 success
Disable CRTC 1 success
(II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: drmOpenMinor returns 12
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: enabled GLX_texture_from_pixmap with driver support
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/r300_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) RADEON(0): Setting screen physical size to 376 x 301
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 2.2.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device ImExPS/2 Logitech Explorer Mouse
(**) ImExPS/2 Logitech Explorer Mouse: always reports core events
(**) ImExPS/2 Logitech Explorer Mouse: Device: "/dev/input/event6"
(II) ImExPS/2 Logitech Explorer Mouse: Found 5 mouse buttons
(II) ImExPS/2 Logitech Explorer Mouse: Found x and y relative axes
(II) ImExPS/2 Logitech Explorer Mouse: Found scroll wheel(s)
(II) ImExPS/2 Logitech Explorer Mouse: Configuring as mouse
(**) ImExPS/2 Logitech Explorer Mouse: YAxisMapping: buttons 4 and 5
(**) ImExPS/2 Logitech Explorer Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "ImExPS/2 Logitech Explorer Mouse" (type: MOUSE)
(**) ImExPS/2 Logitech Explorer Mouse: (accel) keeping acceleration scheme 1
(**) ImExPS/2 Logitech Explorer Mouse: (accel) filter chain progression: 2.00
(**) ImExPS/2 Logitech Explorer Mouse: (accel) filter stage 0: 20.00 ms
(**) ImExPS/2 Logitech Explorer Mouse: (accel) set acceleration profile 0
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) Macintosh mouse button emulation: Close
(II) UnloadModule: "evdev"
(II) ImExPS/2 Logitech Explorer Mouse: Close
(II) UnloadModule: "evdev"
(II) AT Translated Set 2 keyboard: Close
(II) UnloadModule: "evdev"
Output CRT1 disable success
Blank CRTC 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC 1 success
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xefffe000 0xefffe000
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(II) RADEON(0): avivo_restore !
Enable CRTC 0 success
Unblank CRTC 0 success
(II) RADEON(0): [drm] removed 1 reserved context for kernel
(II) RADEON(0): [drm] unmapping 8192 bytes of SAREA 0xf802f000 at 0xb79a0000
(II) RADEON(0): [drm] Closed DRM master.
Last edited by edenxavier (2009-07-28 03:31:10)

Macbook pro 2.4 will not start up. Blank screen!

My Macbook pro just quit the other day. Blank screen and I don't get the bong at start up. I moved the ram around and it bonged once but I can't repeat it. Pulled hard drive to get info off and replaced with new one since it was from July 07. Could zap PRAM with bong but no change.

Hi Lisa,
Try the following:
Boot from install disc (insert disc > restart > immediately hold down the c key and keep holding it until you see “Preparing Installation”) > at first screen select the language and click Continue > click on the Utilities Menu in the menu bar > select Disk Utility > select your HD in the panel on the left side (the name of the HD’s manufacturer and the model number, usually the top item in the list) > look at the bottom of the main window next to S.M.A.R.T. status and see if it says “Verified” (good) or something more ominous like “Failing.”
If S.M.A.R.T. status is "Verified," run Repair Disk > click Repair Disk at bottom of main window. Run this at least twice, and keep running it until it says “appears ok” twice in a row. If that doesn’t happen, you may need a stronger utility (such as DriveGenius, TechToolPro, DiskWarrior) or if the directory is damaged beyond repair, you may need to reinstall the OS, or you may have a damaged HD which will need to be replaced (repair utilities can only repair the directory structure, not the HD itself). When this is finished, quit Disk Utility, quit the installer, and restart. Once booted normally, go to Applications > Utilities > Disk Utility and run Repair Permissions.

My laptop ( hp pavilion dv6-6b27nr entertainment PC) willl not start up. the screen is blank.

I have a HP Pavilion dv6-6b27nr Entertainment PC (Win 7) It would start up with the message "BIOS RECOVERY" . It then would not start up at all. I took it to a repair shop, they contacted HP and got it working. i took it home and it worked just fine the same day, however when I tried to use it the next day the screen is just blank. i tried the take out the battery process with no effect. i then tried tapping the f11 key at start up. the fan came on and it made some noise, but has failed to show anything on the screen. When I turn it on the caps lock key blinks continually in a sequence of two blinks. (When i brought it home from the repair shop I downloaded malwarebytes and quarantined 87 pups etc. )

HI @owe ,
Thank you for your query, I will do my best to help!
I grasp that you received a bios error and the notebook would not start. You took it to a repair shop, who contacted HP and got it back up and running. When you took it home it ran fine. You downloaded malwarebytes, installed and ran it, and quarantined 87 pups etc. When you tried to use it the next day you get a blank screen and the lights blink twice.
Here is a link to Computer does not start and the LEDs blink or the computer beeps . Two blinks again refers to the bios.
You should not be having a bios problem so soon after just having it repaired.
There may be a hardware issue that is causing this and I would test the hardware rule that possibility out. Testing for Hardware Failures (Windows 7, Vista)
If you are still unable to determine any problems, you would have some options.
You can try to restore the bios yourself. Restoring the BIOS
As you just got it back from the repair shop, you could take it back to them to see what they say.
As you stated that the repair shop called HP, you may be able to acquire a reference or case number to refer to and call them yourself. Just to clarify you do not need the case number to contact HP support but it would allow them to more easily locate any case notes from the previous call.
Please call our technical support at 800-474-6836. If you live outside of the US/Canada Region, please click the link below to get the support number for your region. Phone Assist Worldwide
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Failed to start up - blank screen!

Similar Messages

Maybe you are looking for