Failed to transmit & internet not working

Hello,
iny one app, then i try to update, i get error "Failed to transmit". I have a BlackBerry service ordered and I have 800 MBs of Internet left. There are four dots near 3G in the bottom. The browser isn't working too. But then i connect to WiFi everything works. Also i noticed that my time zone not update as it has to. Then i choose Helsinki (+2) time zone my time changes to +10.

Hi and Welcome to the Community!
With a strong carrier network signal (e.g., not merely WiFi), I suggest the following steps, in order, even if they seem redundant to what you have already tried (steps 1 and 2 each should result in a message coming to your BB...please wait for that before proceeding to the next step):
1) Register HRT
KB00510 How to register a BlackBerry smartphone with the wireless network
Please wait for one "registration" message to arrive to your Messages app
2) Delete and Resend Service Books
KB05000Delete the service book for the BlackBerry Internet Service email account from the BlackBerry smartphone
If you have no CMIME entry, then skip the deletion
KB02830 Send the service books for the BlackBerry Internet Service
Please wait for "Activation" Messages, one per already configured email account, to arrive in your Messages. If you have no already configured email accounts, please wait 1 hour.
3) Reboot
With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes.
See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Hopefully that will get things going again for you! If not, then you should contact your mobile service provider for formal support.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

HT4993 why does my internet not work when not connected to wifi?

why does my internet not work when not connected to wifi

Hi farmgirl0812,
Thanks for using Apple Support Communities. This article has steps to try if you are unable to connect to a cellular network:
iPhone: Troubleshooting a cellular data connection
http://support.apple.com/kb/ts3780
Cheers,
- Ari

Internet not working and printer connected by cable but it is unable to communicate with the compute

Changed print cartridge and then problem started.
Internet not working and printer connected by cable but it is unable to communicate with the computer

Hi Joanna 59
Sorry to hear that you are having this issue and Hope you are well;
1.Do you see any light on the back on the printer where the cable is connected?
2. Do you see lights on the back of the router where the cable that comes from the printer is connected?
3.What type of cable are using to connect the printer? Have you try another cable to see if the problem is the current cable.
Please kindly include;
What router are you using (Brand and model)
Operating system i.e. Win 7
Complete Printer model
Thanks;
RobertoR
You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

Internet not working after turning Airport on

Hello,
All of a sudden, I can not connect to the internet when I turn the Airport on. The signal looks strong. But when I open my browser, it gives an error page. On a cafe where there is a free wireless internet that I go to often and had no problems connecting, gave me this message recently.
IP Configuration
192.168.1.46 in use by 00:18:39:88:81:fc, DHCP Server 192.168.1.1
Is there anything that I need to update in my Airport settings? If so, where? I have been trying to look for that and don't seem to have any luck.
Thanks for any help.
Rich
G4 Mac OS X (10.4.8)

See your other thread " Internet not working after turning Airport on".

Airport: Internet not working

Airport has self assigned IP address and will not connect properly to the internet. Have tried manually entering the IP address from another computer on the same network but still cannot connect to the Internet...Any advice/suggestions much appreciated

See your other thread " Internet not working after turning Airport on".

My internet not working

I must did something to my phone and the internet not working not on my wireless or att network that odd.
Safari could not open the page becuase the sever stopped responding that the error message but dail my phone still works.

I travel between Central New Jersey and New York City everyday, and EDGE has been awful for the past two weeks. In my wishful thinking, I've been turning flight mode on and off, and resetting the phone.
After seeing this, I can relax and put up with the crappy service
Today there is nothing...nada...zippo.

Internet not working - wifi connected but internet and server fail, ethernet cable doesn't work either

All of a sudden the internet on our Macbook Pro does not work. We connect through an Airport Extreme and other mac works fine. It shows that wifi is fully connected but when i go to diagnostics, i see the internet and server are failing. I tried connecting an ethernet cable and it doesn't work that way either. Have restarted and reset modem and router, nothing is working… help!

Hi ehamzic1,
Welcome to the Apple Support Communities!
I understand how frustrating it can be when your computer cannot connect to the internet. In your situation, you will need to isolate to find what is causing the issues connecting. I would recommend reading over and working through the attached article. The article should help you troubleshoot and resolve this situation.
Solutions for connecting to the Internet, setting up a small network, and troubleshooting
http://support.apple.com/kb/HT1714
Have a great day,
Joe

Port forwarding for the Web server for outside Internet (not working , help!!!!!!)

Hello
I am trying to learn something new here. We have web server inside our organization its IP address is 172.16.0.35. We want outside Internet users to access web server, How is it possible? Please have a look at the running configuration. Web server is working inside the organization but not at outside. Our Static Public IP is 197.255.232.15 it is assigned to Inetrface Gigabit ATM0.1 and ISP default GW is 197.255.232.1. Let me know whats next? How do I make web server inside the organization available for outside Internet users. Thank you.
Building configuration.
Current configuration : 1983 bytes
! Last configuration change at 17:57:15 UTC Sat Jan 24 2015
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router_test
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
ip dhcp excluded-address 172.16.0.34
ip dhcp pool test
network 172.16.0.32 255.255.255.224
dns-server 197.255.224.18 197.255.224.66
default-router 172.16.0.34
lease 9
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGL1818236L
controller VDSL 0
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no atm ilmi-keepalive
interface ATM0.1 point-to-point
description ATM Routed Bridge Encapsulation (RBE) Internet
ip address 197.255.232.15 255.255.248.0
ip access-group netin in
ip access-group netout out
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
atm route-bridged ip
bridge-group 1
bridge-group 1 spanning-disabled
pvc 0/35
encapsulation aal5snap
protocol ip inarp
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
description Lan
ip address 172.16.0.34 255.255.255.224
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1454
interface Dialer1
no ip address
ip default-gateway 197.255.232.1
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list natlist interface ATM0.1 overload
ip nat inside source static tcp 172.16.0.35 443 197.255.232.15 443 extendable
ip route 0.0.0.0 0.0.0.0 ATM0.1 197.255.232.1
ip access-list extended natlist
permit ip 172.16.0.32 0.0.0.31 any
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input all
end
http://pastie.org/9858814

Hi Karsten Iwen
I deleted ( ip access-group netin in and ip access-group netout out) but it still does not work
my config :
Building configuration...
Current configuration : 2267 bytes
! Last configuration change at 15:43:06 UTC Wed Jan 28 2015
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
ip dhcp excluded-address 172.16.0.34
ip dhcp pool my
network 172.16.0.32 255.255.255.224
dns-server 197.255.224.18 197.255.224.66
default-router 172.16.0.34
lease 9
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGL1818236L
controller VDSL 0
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no atm ilmi-keepalive
interface ATM0.1 point-to-point
description ATM Routed Bridge Encapsulation (RBE) Internet
ip address 197.255.232.15 255.255.248.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
no ip virtual-reassembly in
atm route-bridged ip
pvc 0/35
encapsulation aal5snap
no protocol ip inarp
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
description
ip address 172.16.0.34 255.255.255.224
ip nat inside
no ip virtual-reassembly in
ip tcp adjust-mss 1414
interface Dialer1
no ip address
ip default-gateway 197.255.232.1
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list natlist interface ATM0.1 overload
ip nat inside source static tcp 172.16.0.35 443 197.255.232.15 443 extendable
ip route 0.0.0.0 0.0.0.0 ATM0.1 197.255.232.1
ip access-list extended natlist
permit ip 172.16.0.32 0.0.0.31 any
line con 0
no modem enable
line aux 0
line vty 0 4
end
Router#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 197.255.232.15:5183 172.16.0.33:5183 212.95.74.5:80 212.95.74.5:80
tcp 197.255.232.15:5196 172.16.0.33:5196 212.95.74.5:80 212.95.74.5:80
tcp 197.255.232.15:5602 172.16.0.33:5602 174.129.246.27:80 174.129.246.27:80
tcp 197.255.232.15:5785 172.16.0.33:5785 31.13.93.3:443 31.13.93.3:443
tcp 197.255.232.15:443 172.16.0.35:443 --- ---

Self-Assigned IP....Internet Not Working

Hi--
Let me start off by saying I have absolutely no idea how this happened. I went to start my Macbook this morning and the Internet didn't work. Usually this is not big deal, and I just unplug the router and everything works fine. However, this time (for whatever reason) was different. When I go to my network settings, it says "Self-Assigned IP" under Airport and that "AirPort has a self-assigned IP address and may not be able to connect to the Internet." I was browsing other forums, and found that sometimes renewing the DHCP lease works. I did this, and still no Internet.
How do I fix this??
Thank you.

Hi - this may help.....I sort of had the same problem with my wired connection.
Although I think my router is dying - I hooked my Macbook directly to my modem and my network said that it had a self-assigned IP address but could not hook up to the internet (although it had green lights for the Ethernet, Network settings and ISP)....
I used the 'Automatic' location and the DCHP with manual address setting (or it was the Manual setting) - I got told that what it is doing is just randomly selecting a IP address to use but the address it chooses isn't actually able to work...
(This what I was told) - I entered my IP address (I had copied it down from previous network setups) and I had to type in my router address (even though I wasn't using one I still had to have a number for it to use) - plus a subnet address.....
After that it picked up my internet and works ok......I have to get a new router so hopefully I can connect it all up as it was before.....
This may help - although my set up is slightly different....

MacBook Air internet not working

I have a MacBook Air and just the past couple days the internet is not working correctly. I go to Facebook and I can't scroll the screen or click anything. Other sites work for a bit then stop. I don't know if I have a virus or what is going on please help me. Also I had to use my iPhone to write this because of course my computer wasn't working.

Please answer as many of the following questions as you can. You may already have answered some of them. In that case, there's no need to repeat the answers.
Have you restarted your router and your broadband device (if they're separate) since you first noticed the problem? If not, do that now and see whether there's any change.
If your browser is Safari, then from the Safari menu bar, select
Safari ▹ Preferences... ▹ Privacy ▹ Remove All Website Data
and confirm. Any change?
Quit and relaunch the browser. Any change?
Log out and log back in. Any change?
Are any other web browsers installed, and are they the same? What about other Internet applications, such as iTunes and the App Store?
If other browsers and Internet applications are also affected, follow these instructions and test. Any change?
If only Safari is affected, launch the Activity Monitor application and enter "web" (without the quotes) in the search box. If a process named "Safari Web Content" is shown in red or is using more than about 5% of a CPU, select it and force it to quit by clicking the X or Quit Process button in the toolbar of the window. There may be more than one such process. Any improvement?
Are there any other devices on the same network that can browse the Web, and are they affected?
If you can test Safari on another network, is it the same there?
If you connect to your router with Wi-Fi and you can also connect with Ethernet, do that and turn off Wi-Fi. Any difference?

Internet not working please help!!!!

hi i jus tried to download abode falsh player on my computer. it all downloaded fine and then when i went to go onto the internet my main search page is called babylon. the computer lets me on the internet and then as soon as i log onto facebook hotmail etc it comes up with internet explorer not working.it goes to troubleshooting but comes up with nothing wrong,what have i done??? i need to be able to log into my hotmail as i do all my own work invoices and have to sent them on but my computer now wont let me.please help. ive deleted all the things i downloaded and turned the computer off but still made no difference.please help thanks

steph,
Please re-state your premise.
1) Did you actually download and install an alleged adobe flash player, or not?
2) Was this download a "pop-up" during a browser session, or a "pop-up" on the taskbar?
If it pops up from the browser session, always ignore it. Go to the offical webpage and then download.
3) Was "babylon" your original main search page, or did you get it with the download install?
You could attempt to fix it with a restore point prior to the install of this program.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

Internet not working through Apple applications, but ok in firefox?

I'm having trouble with my internet connection through Apple software on my computer. It started a few days ago, I don't think any changes have been made to my network.
Basically if I try to connect to the internet in Safari, Mail, iTunes, Dashboard or anything else that's an Apple program, it doesn't work at all. It spends a huge amount of time "Loading..." and sometimes will eventually come up with the information but usually times out.
However, if I use Firefox - which I had luckily installed on my computer - all pages and everything load instantly.
I connect to the internet through an Airport which we bought three months ago. The Airport connects to a modem which connects to the line.
What is wrong and how do I fix it?? I much prefer using Safari and I'm dying because I can't get into the iTunes store!!

Hi and welcome to Discussions,
Firefox is one of the few applications that maintain their own 'Proxy'-settings and do not use the general 'Proxy'-settings of OSX like all the other apps you mentioned to not work.
Check the Proxy-settings of Firefox against the general OSX ones.
Hope it helps
Stefan

"Automatically retrieve CD track names from internet" not working

I'm about to begin re-ripping all my CDs (400+) which I haven't done since at least 14yrs ago in order to take advantage on newer/better formats. I was excited to see that iTunes can automate a lot of this process with the following two options:
- When you insert a CD: (Import CD and Eject)
- [ ] Automatically retrieve CD track names from internet
Found in the "Playback" settings of iTunes 10.1.1
However after inserting my first CD, I noticed it started to import without downloading the track names first. Obtaining track names manually is working for me because if I choose "Advanced -> Get track names" it accesses Gracenote DB and works fine.
It's just the automatic operation after inserting a CD that is not working. This causes me to have to:
1) Insert CD
2) Choose "Advanced -> Get track names"
3) Click "Import CD"
4) Eject
as opposed to the one supposedly promised step of "Insert CD" and have the other 3 things happen automatically.
I've tried deleting my iTunes plists in my ~/Library/Preferences/ folder but it still works the same.
Any suggestions?

You can seach the Gracenote site directly. I don't know if that would help you decide which option you needed to use.
http://www.gracenote.com/music/index_old.html

RDP from internet not working in Hyper-v VMs

Hello .
Sorry for my english .I hope to explain clearly my problem .
I 've Hyper-v on Windows 2008 server r2 . I've 3 Virtual networks ( External , Private and internal ) .
In my VMs there are two domains . The first one is bound with internal Vn and the second is bound with private Vn. My Host RRAS is configured to switch inbound connection RDP (3389) to a second RRAS (Virtual machine bound with private network) . Last
RRAS does port forwarding correctly to the machine for RDP connection ( port 3389) request .
RDP works only from host and VMs but not from internet in private vn.
RDP from internet connects but when try to configure session disconnects . Any ideas ?
Netstat says "SYN-RECEIVED" then disconnects .
All other services work fine (http mapped between RRAS host and RRAS vm i) and RDP works in private virtual network from internet . I think the problem is nat over nat for port 3389 in internet connection . I've tried to disable firewall but
not works .
Thanks

Also add firewall exception "from" any or specific ip "inbound" "to" whichever destination.
To truly test, you ca disable firewall, if it allows rdp session, then you know it is something with firewall.
Remember sometimes antivirus software includes firewall., and in the case of home routers, they have built-in firewall, and Windows also has firewall, so you must be sure to check ALL possible locations of firewall blocking and dropping (even server-to-server).
Basically you would be allowing inbound from your router, NATted through (or routed through) your network, to the destination or allowing inbound from server to server. Also
double check that your server NICs are not having any additional 2nd DHCP interfaces, if so, disable the secondary DHCP NIC and test again. And do:
traceroute
From Internet to the server having the issue and from server to server and it may uncover more details of where things are getting dropped.
I have heard also some ISPs may also try to block inbound RDP or 3389, so be sure and verify that as well.
Please mark as answer if I helped solve your issue. Thank you.
tnjman

Internet not working (ethernet, wifi)

Hey I just added window in mt mac through bootcamp but my internet wont work. It shows the ethernet sign but even if I connect a ethernet cable, it wouldnt work, and it cant even search for any wifi (I counldn't enable wifi network)
Please help.... thanks
Brian

Did you download and install the Boot Camp Windows support software? If you did not, re-read and follow the Boot Camp installation guide for your computer and operating system. http://www.apple.com/support/bootcamp/
Otherwise, read the Windows help for setting up and configuring networks.

Failed to transmit & internet not working

Similar Messages

Maybe you are looking for