Failed To Turn On - Bravia KLV-32R402A

Hi. I have a Sony LED Bravia KLV-32r402A.My TV is failed to turn on. This is the chronology.1. Turn on the TV.2. Sony Image appears3. Turn on for less than 1 minute.4. Off immediately.5. Indicator Light blinking 5 times. I read some references on the internet, the problem is in t-con panel. Is it right?I have a problem to taking it to Sony Service Center because i forgot where my warranty card is.Any solution will be appreciated. Thank you.

Hi afidakbar,
Welcome to the Sony Community!
Please perform power reset. Here are the steps.
Turn off the television.
IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
Unplug the television power cord from the electrical outlet.
Let the television remain without power for 60 seconds.
Plug the power cord back into the electrical outlet.
NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
Turn on the television.
For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
If my post answers your question, please mark it as "Accept as Solution"

Similar Messages

Apple TV 3 not working with Sony Bravia KLV-26T400A

CURRENT GENERATION APPLE TV (3)
Hi I recently bought an ATV 3 which works fine with a Panasonic TV but is not detected on the HDMI input (or any of the others listed in the Sony menu) by a several year old Sony Bravia KLV-26T400A despite the specs saying it supports 1080 p HDMI input. The HDMI lead is the same that worked successfully with the Panasonic TV. I have reset the Sony to factory settings, turned the power on and off; cut the power to the ATV 3 and re-booted and tried the fixes I've seen listed on other threads which speak of editing the External Input labels and skipping the ones you don't use (on the Sony) but none of these have helped, can anyone help?
Thanks
Simon

That does make things more difficult. Is the monitor HDCP compliant? Seeing as it's an issue with the display and not the device the only thing I could suggest is to get hold of another TV in order to lower the resolution on ATV. If that doesn't work then i'm not really sure what else to try i'm afraid.

Macbook display sometimes fails to turn on after shut down (2008 2.4Ghz dual core 2 duo - 2GB DDR2 running OSX 10.6.8)

I own a black macbook (early 2008 model) and for the past few months the display has occasionally (although recently more often) failed to turn on when booting. This only happens every one in four times after a full shut down. When I turn on the computer, I hear the hard drive boot and the fans start going, I also get a response in the white light indicator. When this occurs, I then have to press the on/off button to shut the macbook down, then press the button to turn it on again. Sometimes this works on the second try, but other times it takes 3 to 4 times turning it on or turning it off. Initially I thought it was a hard drive issue (and planned to purchase a new hard drive), but after connecting the laptop to an external screen, the desktop shows up (macbook display remains off despite unplugging or replugging external display). Is this a firmware issue? Or potentially a display cable issue? I'm leaning towards firmware since it only happens every 1 in 4 times. All parts in the macbook are original to 2008 and I've never really had any problems before.
I've tried resetting by taking out the battery/pressing the on button.
I also did a clean 7 pass wipe and reinstalled Mac OSX.
Used TechTool Deluxe - found no issues.
Booted computer and pressed D to perform a Mac hardware test - no problems found.
Not sure what to do now...
These two looked mildly like my problem: http://www.ifixit.com/Answers/View/68700/Not+booting+properly+after+10.6.8+and+F irmware+updates and another suggested replacing the display cable: http://www.ifixit.com/MacBook-Parts/MacBook-Display-Data-Cable/IF186-073?utm_sou rce=ifixit_guide&utm_medium=wiki_text&utm_term=if186-073&utm_content=product_lin k

I own a black macbook (early 2008 model) and for the past few months the display has occasionally (although recently more often) failed to turn on when booting. This only happens every one in four times after a full shut down. When I turn on the computer, I hear the hard drive boot and the fans start going, I also get a response in the white light indicator. When this occurs, I then have to press the on/off button to shut the macbook down, then press the button to turn it on again. Sometimes this works on the second try, but other times it takes 3 to 4 times turning it on or turning it off. Initially I thought it was a hard drive issue (and planned to purchase a new hard drive), but after connecting the laptop to an external screen, the desktop shows up (macbook display remains off despite unplugging or replugging external display). Is this a firmware issue? Or potentially a display cable issue? I'm leaning towards firmware since it only happens every 1 in 4 times. All parts in the macbook are original to 2008 and I've never really had any problems before.
I've tried resetting by taking out the battery/pressing the on button.
I also did a clean 7 pass wipe and reinstalled Mac OSX.
Used TechTool Deluxe - found no issues.
Booted computer and pressed D to perform a Mac hardware test - no problems found.
Not sure what to do now...
These two looked mildly like my problem: http://www.ifixit.com/Answers/View/68700/Not+booting+properly+after+10.6.8+and+F irmware+updates and another suggested replacing the display cable: http://www.ifixit.com/MacBook-Parts/MacBook-Display-Data-Cable/IF186-073?utm_sou rce=ifixit_guide&utm_medium=wiki_text&utm_term=if186-073&utm_content=product_lin k

Unsupported output signal for Sony Bravia KLV-32T550A

I have a mac mini 2007 running 10.6.3. I am trying to connect to a sony bravia KLV-32T550A either through VGA or DVI. Both keep coming up with error message (unsupported output signal, adjust your pc signal)
I have updated setting on the TV as per some forums I have read so am sure its not the TV.
Now the TV says the native resolution is 1366 x 768 but there is no exact match in display settings. Could this be the problems.
I have read that i can download switchresx and this should fix the problem.
Can anyone shed any light on this it would be much appreciated>
Thanks

Definitely the second computer can be a big help. If you set up Screen Sharing between the two so that the mini's screen is shared over to the MacBook, you will be able to see the mini's screen on the MacBook even though the display connected to the mini is dark. And from the MacBook you will even be able to control the mini, so you can go into Displays Preferences on the mini and make alternate selections for resolution and, if necessary, refresh rate. Hopefully you will hit on a combination that will light up the mini's attached display.

Sony bravia klv-32r502c

how to install skype in sony bravia klv-32r502c?pls help

Hi ae_kerone,
Welcome to the Sony Community!
You cannot install application/s on the TV. However, new features and apps will be added automatically via software update.
For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
If my post answers your question, please mark it as "Accept as Solution"

Kanex ATV Pro + Apple TV + Sony Bravia KLV-S40A10

I purchased a Kanex ATV Pro to provide VGA input from my Apple TV to my Sony Bravia KLV-S40A10 as my model does not have HDMI input. I have checked the VGA input on the TV with a laptop which works correctly however when the Kanex ATV Pro is used the TV shows an out of range error, could anyone provide guidance with this problem please.

This is a user to user forum - not many of us have the Kanex device - I've been meaning to order one.
You may get an answer but I still think Kanex would know best.
AC

Re: Qosmio X500 - Monitor fails to turn on after waking from Sleep mode

Hello all,
I have a problem with my Qosmio X500-10T:
After placing it into Sleep mode, upon waking it up again (opening the lid, pressing a key, moving the mouse or pressing the power button) the screen fails to turn on (it could possibly be a black screen, although I doubt it as I cannot really see any traces of the LED backlight). The only way beyond this is rebooting by holding down the power button.
I appreciate any help.

I have a X500-10T, under 4 weeks old. Straight from the box it had the problems with going to sleep/hibernation and the only way to bringit back to life was to remove the battery and follow the reset procedue as instructed by Toshiba technicians. Currently the sleep and hibenation has been disabled, it was unuasble. I have a bluetooth mouse that also is a nightmare, it drops in and out of operation at any time, mostly if left untouched for a while. Some times a reboot brings it back to life whilst at other times it takes 30-40 minutes of switching on and off a number of settings, cant' realy workout what's going on. This unit was supplied with the latest BIOS ver 1.4 so not known any difference.
Technicians aslo did a full re-set bakt to factory defaults, this did not make any difference apard from giving me several hours of work in restalling all my programmes. I am worried as I only have just over 11 months warranty left. I have been advised not to use the fingure print identification system as any protected data will be un recoverable if it goes wrong, I would be interested if any other users have any concerns about this, the reminder to set this is driving me crazy, and apparently it can't be switched off when I asked.Has any one who had thee issues managed to get it sorted. The big question for me is it a BIOS problem, graphic card software issue or a Windows 7 issue.

ICloud Backup failed. Turn off Airplane Mode or use Wi-fi.

iCloud Backup Failed. Turn off Airplane Mode or use Wi-fi. Airplane mode is turned off and I am connected to wi-fi but still I can't backup. What do I do now?

Hi Barbara,
I just had the same issue.
resolution:
get to your network settings - disable wifi, then enable 3G and cellular connection
Now get back to icloud backup menu and try to enable. of course it wont work. back again to network settings switch wifi back on, and got to icloud again. This time it will allow you to set your backup
cheers :-)

Sony A7 failed to turn on after updating firmware 2.00

As i mentioned, my Sony A7 failed to turn on after updating firmware 2.00. It just appear a blank screen after click the finished button on the updating app on Mac. I waited for more than an hour and there is still no thing happened.

I bought the Sony A7II a few days ago. It initially charged just fine, but today I tried to charge it using the cable with an electrical outlet as well as the USB to computer. Neither one would get the charge light to illuminate. Not feeling the love Sony. I just purchased a Flash, wrist belt, filters, etc... I'm definitely not happy. It seems this is a problem!

HT201401 my iPhone 4s fails to turn on. When I press the sleep button the apple logo shows displays but nothing happens after that

iphone fails to turn on. The apple logo shows up but nothing happens after that

Hi Haleynichole_99!
I have an article here with some troubleshooting steps that can help you resolve this issue with your iOS device:
iOS: Unable to update or restore
http://support.apple.com/kb/HT1808
Thanks for using the Apple Support Communities!
Cheers,
Braden

Iphone 3gs shutdowns random, it fails to turn on, it displays a white screen with colors lines

I have an iPhone 3GS. It It shutdowns random, it fails to turn on, it displays a white screen with colors lines.

I have the 3GS and it recently started the RSD. At first I thought it was just the batter not holding a charge and being lower than what the display showed. However, even when fully charged the RSD's occur mostly when loading either Apps or web pages in Safari.
I have not experienced the white screen and colored line, yet apparently. Is this the logic board like in the MacBook's?
iPhone 3GS, IOS 4.2

TS3992 Altho' my 4S iPhone is connected to Wi-fi & I have a correct Apple/icloud ID and password, I keep getting the message "icloud backup Failed. Turn off airplane mode, or use Wi-Fi to enable iCloud backup." Should I delete my account,setting up a new

I cannot activate my iCloud backup of my 4S iPhone, even though I have definitely deactivated Airplane mode, and am connected to Wi-Fi. I also have a correct Apple/iCloud ID and password.
Should I delete my iCloud account and set up a new one??
Please give me some assistance with this problem!
Sincerely, Brianrit

To unfreeze it, reset it by holding the power and home buttons at the same time until you see the Apple logo, then release.
To troubleshoot your problem with backing up to iCloud, this may be caused by a corrupt existing backup that needs to be deleted, or by data on your iPad that is preventing the backup from succeeding. To troubleshoot these, try deleting your last iCloud backup (if you have one) by turning off iCloud Backup in Settings>iCloud>Storage & Backup, then tap Manage Storage, swipe across your backup and tap Delete, then go back and turn iCloud Backup back on and try backing up again.
If it still won't back up, you may have an app that is preventing the backup from succeeding. To locate which one, go to Settings>iCloud>Storage & Backup>Manage Storage, tap the name of your device under Backups, under Backup Options tap Show All Apps, then turn them all to Off (including camera roll) and try backing up again. If it succeeds, then the camera roll and/or one of your apps is preventing the backup and you'll have to located by process of elimination. Turn the camera roll On and try backing up again. If it succeeds, turn some of your apps to On and try backing up again. If it succeeds again, turn some more apps to On then try again; repeat this process until it fails. Eventually you'll be able to locate the problem app and exclude it from your backup.

HP Pavilion 15-e092sa has stopped working and fails to turn on.

My hp pavilion laptop has stopped, it cut out completely as I was using it and it fails to restart. Even after taking the battery out and leaving it on charge it won't even turn on, and no lights come from the laptop. Any suggestions?

Then it is possible that your power adapter is no longer functional.
Have you tried all of the power& battery and the Startup shutdown troubleshooting in the Solve a problem HP support portal for your notebook?
All of that priceless information is there for you to try and it can possibly even enable you to resolve the problem or identify the issue on your own.
Selectively troubleshooting queries posed by those of us trying to help here in the forum does not help anyone, including yourself.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

My iPod now turns off after failing to turn off.

When my iPod couldn't turn off and the battery drained, I deleted "the song" when the problem came, full-charged it via the computer and it haven't occurred again.
I occurs to me:
1-Sometimes certain files get corrupted, for example word files, and get the application fail. I am not sure this fixed the problem but for the moment everything is OK with my iPod.
2-I noticed that when my iPod is recharged, I need to wait two or three minutes for turning off, otherwise it is imposible. And if you hear closely there is some noise in it. Don't try to turn off inmmediately after recharging it.

Excuse me, I wanted to post at the iPod video forum.

Failed info package, failed request turns from red to green after 1 hour so

hi,
There is a failed info package and if u go to monitor screen, the request status will be red in colour but then the same request after 1 hour or so turn from red to green automatically, why is this, what could be the possible reason??????????

Hi Lieu.
The system automatically sets the status for the load to incorrect if the waiting time is exceeded. The load will still be running even though it might look incorrect, and that is why it turns green when it is complete (and everything is correct).
You can set the waiting time if you go to the monitor -> choose a request -> settings -> waiting time up to status incorrect (ctrl + F9).
Hope it helps (assign points if helpfull!).
BR
Stefan

Failed To Turn On - Bravia KLV-32R402A

Similar Messages

Maybe you are looking for