Failed update ios 8.02 and failed to restore to factory settings

I attempted to update to IOS 8.02 and that failed I was instructed to to re set to factory settings and that failed I am now left with a blank screen showing an iTunes logo and a connection cable logo.
I tried turning PC off and rebooting but still no joy. I currently have a dead iPad mini any help please

Your iPad is in recovery mode. Try this now.
If you can't update or restore your iPhone, iPad, or iPod touch

Similar Messages

  • Unsuccessful update via iTunes. It asks to restore to factory settings.

    I was trying to update via iTunes and it said unsuccessful update. Why I do not know i didn't do anything while it was updating. Didn't even touch the computer. It says i have to restore the phone to factory settings. Is there anyway I can keep this from happening? It says iTunes has detected an iPhone in recovery mode. You must restore this phone before it can be used with iTunes. Then when i try and restore it it only says restore to factory settings. I will lose all data, photos and videos on there.

    Same thing happened with my iPhone 4S - no one is any help.  Thanks Apple for such a crappy update!  I've called Apple, they say the SIM card needs replacing, I go to my service provider they tell me nothing wrong with the SIM card - provider tells me I now need a new phone.  Sheesh!  If someone has a solution to this it would be greatly appreciated.

  • My 1st generation ipad won't power up. It flickers but then no display. It is fully charged and I have restored to factory settings

    The ipad originally lost half of the display on the screen and now won't display at all, other than a slight flicker when you first try to turn on. I have been able to back up the contents and have restored to factory settings. The battery is fully charged. There is about 20gb of memory space available. Please can anyone help in diagnosing the problem?

    The screen has probalby died. Or the backlight.
    You can look into getting it fixed but you may be at the point of comparing investing to fix an older device or putting that money towards something newer that will have a longer life.

  • Ipad Air disabled and will not restore to factory settings.

    Hi Guys,
    I recently had my ipad disabled by my little brother. He didn't know the password and kept going until he was completely locked out of it. I am familiar with restoring the device as it has happened once before.
    That time it all went smoothly. However now I cant seem to get past the updates. Every time I try to restore the device it begins to update and then fails an hour into the process. It's so bloody frustrating.
    Is there any particular reason why this update keeps failing or anyone know how I can restore without updating??
    If it helps I receive a message of an "unknown error -39" which keeps appearing.
    All help will be greatly appreciated as I have important projects on this thing

    I do not know that that particular code means, but many times, antivirus software and USB connections can have a negative impact on restoring with iTunes.
    My suggestion would be to quit iTunes, restart both devices, disable your firewall and antivirus software, and use another USB a port if you have one to use.

  • HT1339 I have an IPOD Nano 4th Generation 8GB and need to restore to factory settings as want to sell it; however it will not reset and when plugged into my MAC it says firmware corrupt? CAn anyone shed light on what i can do to overcome this issue?

    I have an IPOD Nano 4th Generation 8GB and am unable to restore it back to factory settings even when it is connected to my MAC.  I have tried the menu/select hold but is not doing anything.  When connected to the MAC and select restore in itunes it comes up with 'Firmware Corrupt'.  It also states the IPOD is up to date.  I have the latest operating system on my MAC and wonder if this may be part of the issue?
    Can anyone shed light as to what i can do to reset it back to factory settings as would like to sell it and ensure it is ready for the new owner.
    Thanks
    jay68g

    See here: What to do if iPod can't be updated because the firmware file was corrupt or not found
    B-rock

  • I had a software problem with my iPhone 4S and had to restore to factory settings. I had everything backed up on iCloud, but I was told not to restore using that backup. How do I get my photos back? I know it's on iCloud.

    The Genius at the Apple Store restored my phone to factory settings. I had backed everything up on iCloud, but he recommended that I don't restore that old backup file since it might bring up the software issue again. I just want to get my photos back. Is there anyway to retrieve them from iCloud without having to restore my phone using my old backup? Or would I have to use the old backup, transfer my photos, and then do another factory restore? Help!

    You would have to restore the backup, import the photos to your computer, then restore as new again.

  • I recently got a hand-me-down Macbook (white) 2010 and want to restore to factory settings. The computer did not come with any discs. It is running 10.6.8 and I purchased 10.6.3 recently to upgrade my MacBook Pro. Can I use that to restore the MacBook?

    I want to give the hand-me-down to my kids so they will stay off my MacBook Pro I'd like to start fresh with the MacBook, remove all the former owners information, restore it to factory settings, but it did not come with any installation discs, so I don't know what to do. I recently purchased Snow Lepoard for my 2008 MacBook Pro. Can I use that to restore the MacBook? Also, the former owner purchased Microsoft Office (ugh) with the computer but again, no installation discs. How do I keep that when I restore?
    Any help would be appreciated.
    Thanks!

    I purchased a mini to HDMI cable and tried to connect to the TV but the TV is not recognizing the computer. I attempted to set sound and display settings under the "my Preferences" utility with no success.  Again, I'm not sure if I need to upgrade my OS software Any Suggestions?

  • I have a 6th generation ipod  classic and i cant restore to factory settings because of erro 1139

    Please help i cant restore my ipod classic 6th generation to factory settings because of error 1139

    Did you follow the instructions here:
    http://support.apple.com/kb/HT4367
    Pay attention to differences in power connection depending on whether or not you have AppleTV2 or AppleTV 3.
    Also some microUSB leads don't seem to work - try another if you can. Disconnect superfluous USB device/hubs too if possible.
    AC

  • HT201376 just got a used macbook pro and want to restore to facory settings how do i do is

    I just got a used macbook pro and want to restore to factory settings....how do i do this safely?

    Click here and follow the instructions. If the computer originally shipped with Mac OS X 10.6.8 or earlier, when you reach step 5, insert its original disk, restart with the C or Option key held down, use the Disk Utility to erase the internal drive, and install a fresh OS.
    (118569)

  • Unable to verify update. iOs 8.0.1 failed verification because you are no longer connected to the internet.

    I have updated my iPad, my wife's iPad, but both our iPhones (5S) and (5C), give the following error every time we try.
    "Unable to verify update. iOs 8.0.1 failed verification because you are no longer connected to the internet."
    We are obviously connected to the internet because the updated downloaded on all 4 devices, but the iPhones will not go the next step.
    Wifi ok
    Connection ok
    Help ...
    Mark

    Apple has pulled the iOS 8.0.1 update due to problems.
    iOS 8.0.2 will be released in "the next few days".
    Loss of cellular service or ability to use Touch ID after updating to iOS 8.0.1 on iPhone 6 or iPhone 6 Plus
    We have a workaround for you if you have an iPhone 6 or iPhone 6 Plus and you lost cellular service and Touch ID functionality today after updating to iOS 8.0.1. You can reinstall iOS 8 through iTunes by following the instructions below. We are also preparing iOS 8.0.2 with a fix for the issue, and will release it as soon as it's ready in the next few days.

  • HT5957 Unable to update. I phone keep getting this msg.   Unable to verify update iOS 7.0.2 failed verification because you are no longer connected to Internet

    Unable to verify update iOS 7.0.2 failed verification  because you are no longer connected to Internet

    I still haven't seen a solution to the problem "unable to verify update iOS 7.0.2 failed verification because you are no longer connected to internet"
    I did not have my iPhone plugged in to power during download, had plenty of power.
    Download burped once and restarted download.
    I got to the Verification step and it failed multiple times.
    I plugged in power, I turned off iPhone and restarted.
    I tried to do the download again and it goes to the Verify step
    and get the same error message.
    I do not have an Apple PC, but, have a Windows 8 PC.
    WIll iTunes help better manage the update?
    rdmayo

  • HT4623 Started to download IOS 6.1 and failed to complete due to no wall charger. Now download fails w "failed verification be

    Started to download IOS 6.1 and failed to complete due to no wall charger. Now download fails with "failed verification because no longer connected to internet. Wi-fi shows my linksys. What's up?

    1968GTX wrote:
    I think maybe the download is in the phone because it switched from download to a preparing message. It almost completed, blu bar nearly full and then the fail message. Today, on a different wi-fi, I get the Unable to Verify Update message. Is there a way to clear and start over?
    Seems to be a content expiration issue, probably to keep the load down on the servers hosting the updates.  I've found that resetting your network settings does the trick, even if it is a little overkill. 
    settings - general - reset - reset network settings
    originally posted here:  https://discussions.apple.com/message/21300337#21300337

  • I have a 4S and just tried updating to the latest iOS version and my phone went into recovery mode and iTunes says I need to restore to factory settings. Anyone know how I can fix my phone without losing all my content?

    I have a 4S and just tried updating to the latest iOS version and my phone went into recovery mode and iTunes says I need to restore to factory settings. Anyone know how I can fix my phone without losing all my content?

    You would only be able to restore to a backup to iCloud or iTunes:
    Restore from Backup
    Cheers,
    GB

  • IPhone 4 crashed during ios update (5.0.1) and won't restore. anyone know how i can get my iPhone working again?

    iPhone 4 crashed during ios update (5.0.1) and won't restore. anyone know how i can get my iPhone working again?

    Try to force your phone into recovery mode. Disconnect it from the computer's USB cord. Turn it off if you can by holding the sleep/wake switch until you see the red slide to off. If you can't turn it off, please continue. Press and hold the home button while plugging it into the computer's USB cord. Continue holding the Home button while iPhone starts up. While starting up, you will see the Apple logo. When you see "Connect to iTunes" on the screen, you can release the Home button and iTunes will display the recovery mode message. See http://support.apple.com/kb/HT1808 for details.
    Then you can restore your phone: http://support.apple.com/kb/HT1414

  • Rescue and Recovery "restore to factory settings" fails

    I have had need to recover my T61 to the state of original receipt. I boot from the recovery startup disc and select that I wish to recover to factory settings, and that I wish to save no files. After a progress bar fills, I am prompted to insert Product Recovery Disc 1. After it has completed, I am prompted for Disc 2, then Disc 3, etc., until the Disc 8. After the last disc progress bar is filled, I am presented with the message "Product Recovery failed to restore your system." The T61 then boots to the Rescue and Recovery menu. I have attempted this once again and have the same result. Please help if you can!

    Trying to do a restore to factory settings, ive tried holding down '0' on bootup but i get nothing it just goes starts up.
    I want to totally reset to factory settings, but unable to do it?
    You said that Win 8 system run on this notebook.
    As far as I know this notebook Satellite L750D-14R was preinstalled with Win 7 64bit OS.
    This means that HDD recovery procedure will not work because the HDD content and the partitions has been modified!
    To recover the notebook back to factory settings you would need the Toshiba Recovery disk/medium. If you did not create such disk then you could order this here:
    http://backupmedia.toshiba.eu/
    Anyway, I guess that the LAN connection doesn’t work due to LAN driver issue.
    I recommend you to uninstall the LAN driver (in device manager) and to download the latest available LAN driver from Toshiba EU driver page.
    After LAN driver installation reboot the notebook.

Maybe you are looking for

  • PI 7.1 AAE Interface statistics and monitoring

    Hi SAP community! I currently have Advanced Adapter Engine interfaces running through my systems (which bypass Integration Server by design), and my issue is for data/statistics. RWB is able to display the AAE/Adapter Engine messages in groups, but i

  • Wrapping text around YouTube widget

    Does anyone know how to get the YouTube widget to appear inline? I tried to follow the steps below, which works fine for photos, but can't get it to work with this widget. If it's not possible, is there a workaround? Thanks! To make text wrap around

  • Calling one XML Schema in another XML Schema

    Hi All, I am having 2 XSD Files. One XSD file is having DEPT Details with DEPTNO as PK. Second XSD file has got EMP Details with EMPNO as PK and DEPTNO column is also there. I want to establish a Relationship between there 2 files, so that the EMP.DE

  • Deploy app.

    Hi. When I try to deploy my app to standalone Weblogic server then I have error: [Deployer:149140]The task cannot be processed further until the current edit session is activated. When this occurs, task processing will continue. The user can exit the

  • Need help with reinstall of photoshop elements 10 premier. can some please help me

    just installed photoshop elements premier 10 to my computer after hard drive replaced. i cannot get it to set up for me, nor place an icon on the desktop. please help, i have no computer knowledge left in my itty bitty brain. HELP