Failed with code 0x8007000e.

Hi,
I am getting the below error in ccm.log file. Please let me know how to solve this
HTTPPost(URL='http://PSS.abc.com/ccm_system/request'): Failed with code 0x8007000e.
HandleRemoteSyncSend failed (0x8007000e).3
CForwarder_Sync::Send failed (0x8007000e).
Regards,
Boopathi S

"Storage" in this case means memory; aka, RAM. This typically means either the system you are targeting doesn't have enough or your TS is too big.
Also note that log files are about context; a single line from any arbitrary log file is meaningless without knowing what's going on around it.
Jason | http://blog.configmgrftw.com

Similar Messages

Office 2013 SP1 fails with code 17302 - SCCM 2007 R2

Hi,
I am trying to deploy Office 2013, along with SP1, in the following order:
1. Prompt to close all office apps and continue (vbs)
2. Installation of Office 2013, using modified msp.
3. Restart
4. Installation of SP1 with command line /passive /norestart.
I am doing this all through a package I created in SCCM 2007 R2.
The first few programs works well. However, when the installation of SP1 starts, SCCM launches the program, then SP1 fails with code 17302.
Manual installation, through command prompt, with the same switches works fine.
The error is only when remotely deploying.
The system is Windows 7 X86 with latest SP.
Please help!

Hi,
Have you checked the log file? Does it say anything there? Also, where is the SP1 installation file stored? Since this only happens while remotely deploying, check the network or the setting of your filewall.
By the way, you can slipstream Service Pack 1 with your Office 2013 installation media, Office 2013 will be directly installed at Service Pack 1 level, saving you the trouble of applying it afterwards. For the details, please refer to this article:
http://www.howto-outlook.com/otherprograms/slipstreamoffice2013sp.htm
(Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.)
Regards,
Ethan Hua
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

Flash builder 4 Verifying payload integerity : Failed with code 1

where i install flash builder 4 on windows servers 2003 32x
got this error
Exit Code: 7
-------------------------------------- Summary --------------------------------------
- 0 fatal error(s), 2 error(s), 2 warning(s)
WARNING: Payload {7E5AA19B-0B85-4f44-BA26-728851489200} Adobe Flash Player 10 ActiveX is already installed and the session payload {5EE868D6-7B6B-49ee-AF60-09B1358AFFD7} Adobe Flash Player 10 ActiveX has no upgrage/conflict relationship with it.
WARNING: Payload {40F95A03-885A-45fb-9A14-486BEFEDDF34} Adobe Flash Player 10 Plugin is already installed and the session payload {FB7F30B6-BFBF-4d2c-9F61-B5533659ACBE} Adobe Flash Player 10 Plugin has no upgrage/conflict relationship with it.
ERROR: Verifying payload integerity : Failed with code 1
ERROR: Unable to get root from inChildPath
who can help me,i'll thank you very much

Hi,
Please deselect the option of Flash Player in the installer before beginning the installation and see if installation is successful. (Please uninstall Flash Builder and reboot before trying to reinstall)
If that doesn't help, please run the CS5 clean tool with option to uninstall Flash player and FB, reboot after cleaning and now reinstall FB (selecting Flash Player also)
CS5 Clean Tool can be downloaded from http://www.adobe.com/support/contact/cs5clean.html
Please let us know whether this helps.
Thanks,
Deeptika

PurchaseOperation: Purchase failed with code 5002

When I try to download a book that I purchased to one of my workstations, I get the following output within `/var/log/bookstore.log`:
Jun 2 15:55:50 hostname iBooks[17397] <Critical>: MZBookKeeperStoreURLOperation: Starting URL operation with url=https://bookkeeper.itunes.apple.com/WebObjects/MZBookkeeper.woa/wa/getAll / bagKey=(null)
Jun 2 15:55:50 hostname iBooks[17397] <Critical>: -[ISStoreURLOperation _runURLOperation]: _addStandardQueryParametersForURL: https://bookkeeper.itunes.apple.com/WebObjects/MZBookkeeper.woa/wa/getAll
Jun 2 15:55:50 hostname bookstoreagent[1491] <Critical>: ISStoreURLOperation: Starting URL operation with url=(null) / bagKey=buyProduct
Jun 2 15:55:50 hostname bookstoreagent[1491] <Critical>: -[ISStoreURLOperation _runURLOperation]: _addStandardQueryParametersForURL: https://p7-buy.itunes.apple.com/WebObjects/MZBuy.woa/wa/buyProduct
Jun 2 15:55:50 hostname bookstoreagent[1491] <Critical>: ADI: Account is not provisioned, omitting OTP and MD
Jun 2 15:55:50 hostname bookstoreagent[1491] <Critical>: PurchaseOperation: Purchase failed with code 5002 and params productType=PUB&price=0&salableAdamId=5212156335&pricingParameters=HQRDL&ownerDsid=52156526
What should I do to resolve this?

Unfortunately that did not resolve the issue. Same thing happening, but I did noticed something I had not seen previously in system.log:
Sandbox: bookstoreagent(1423) deny file-read-data /Volumes/tank/Users/Shared/SC Info/SC Info.sidd
Sandbox: bookstoreagent(1423) deny file-read-data /Volumes/tank/Users/Shared/SC Info/SC Info.sidb
Sandbox: bookstoreagent(1423) deny file-read-data /Volumes/tank/Users/Shared/adi/adi.pb
So I proceeded to also reset permissions and ACLs on the Shared folder.
Unfortuantely this still availed no positive results and proceeded with another error. I now saw the `adi` folder in the mix. I then also moved it over, but noted that it was still complaining about the `SC Info` folder, even though it does not exist. Obviously the folder is not being recreated and leads me to believe that there is yet some kind of permission issue, even though things should be sane in that regard.
I then `mkdir'd` the `SC Info` folder and then got:
sandboxd[258] ([1423]): bookstoreagent(1423) deny file-write-create /Volumes/tank/Users/Shared/SC Info/.sid.lockFile
sandboxd[258] ([1423]): bookstoreagent(1423) deny file-write-create /Volumes/tank/Users/Shared/SC Info/SC Info.sidb
So obviously the sandobx is having some kind of permission issues here. I could go setting it to 777, but obviously that's not ideal and I'd like to understand what is actually happening here under the sheets that is so elusive...
Oh, also, I did add Deauth and Auth for this computer in between the steps before mv'ing folders (I don't like to rm things initially until I'm sure I've not blown something up... )

Patch 9655006 failed with code 135 when applying to Oracle Restart

Hi all,
I install Oracle RAC single node version 11.2.0.1 on Linux (kernel 2.6.18).
I try to apply patch 9655006 (prerequis for upgrade to 11.2.0.2).
Everything is OK for grid applying with success.
When I apply this patch to oracle db home, I get :
Oracle Interim Patch Installer version 11.2.0.1.5
Copyright (c) 2010, Oracle Corporation. All rights reserved.
Argument(s) Error... Given 'ocmrf' file does not exists.
Please check the arguments and try again.
OPatch failed with error code 135
I've given the complete path and filename (same as for grid applying).
I've found A document [ID 1283954.1], but not useful in my case.
Any ideas for workaround ?
TIA
yang
ps. this does not occur when applying to a RAC with 2 nodes.

yang wrote:
Hi all,
I install Oracle RAC single node version 11.2.0.1 on Linux (kernel 2.6.18).
I try to apply patch 9655006 (prerequis for upgrade to 11.2.0.2).
Everything is OK for grid applying with success.
When I apply this patch to oracle db home, I get :
Oracle Interim Patch Installer version 11.2.0.1.5
Copyright (c) 2010, Oracle Corporation. All rights reserved.
Argument(s) Error... Given 'ocmrf' file does not exists.
Please check the arguments and try again.
OPatch failed with error code 135
I've given the complete path and filename (same as for grid applying).
I've found A document [ID 1283954.1], but not useful in my case.
Any ideas for workaround ?
TIA
yang
ps. this does not occur when applying to a RAC with 2 nodes.Hello Yang,
Could you try it again with debug info? Before you run the opatch, run the following:
$ set OPATCH_DEBUG=TRUE; export OPATCH_DEBUG
Regards
Gokhan

Cumulative Update 3 client update install failed with code 1642

We have SCCM 2012 R2 and recently updated to CU3
Existing client is version 5.00.7958.1000
Pushing update package created during CU3 update failing on some computers
I am trying to update some of laptops using CU3 x86 update and getting following errors
Script for Package:ABC00126, Program: Cumulative update 3 - x86 client update install failed with exit code 1642
I have reviewed many forms but couldn't find relevant.
Update works on about 70% on machines with same image but failed on rest with same 1642 error
Same issues occurs applying client on during TSequence on some of machines.
It is very inconsistent,
Any help would be greatly apprciated
Thanks
RJ
RJ09

I verified package does copied over in ccmcache folder.
Also try to run update package using pstools, got error same as Torsten mentioned.
Here are logs from client.
Checking content location C:\Windows\ccmcache\gt for use
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Successfully selected content location C:\Windows\ccmcache\gt
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Executing program as a script execmgr
13/01/2015 6:56:04 PM 2588 (0x0A1C)
Found executable file msiexec.exe with complete path C:\Windows\system32\msiexec.exe
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Successfully prepared command line "C:\Windows\system32\msiexec.exe" /p configmgr2012ac-r2-kb2994331-i386.msp /L*v C:\Windows\TEMP\configmgr2012ac-r2-kb2994331-i386.msp.LOG /q REINSTALL=ALL REINSTALLMODE=mous
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Command line = "C:\Windows\system32\msiexec.exe" /p configmgr2012ac-r2-kb2994331-i386.msp /L*v C:\Windows\TEMP\configmgr2012ac-r2-kb2994331-i386.msp.LOG /q REINSTALL=ALL REINSTALLMODE=mous, Working Directory = C:\Windows\ccmcache\gt\
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Created Process for the passed command line
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Raising event:
[SMS_CodePage(437), SMS_LocaleID(1033)]
instance of SoftDistProgramStartedEvent
AdvertisementId = "ABC212D1";
ClientID = "GUID:f298da2e-dfd1-428e-8b3c-b03602f95719";
CommandLine = "\"C:\\Windows\\system32\\msiexec.exe\" /p configmgr2012ac-r2-kb2994331-i386.msp /L*v C:\\Windows\\TEMP\\configmgr2012ac-r2-kb2994331-i386.msp.LOG /q REINSTALL=ALL REINSTALLMODE=mous";
DateTime = "20150114005604.541000+000";
MachineName = "DH-07";
PackageName = "ABC00126";
ProcessID = 3496;
ProgramName = "Cumulative update 3 - x86 client update install";
SiteCode = "abc";
ThreadID = 2588;
UserContext = "NT AUTHORITY\\SYSTEM";
WorkingDirectory = "C:\\Windows\\ccmcache\\gt\\";
execmgr
13/01/2015 6:56:04 PM 2588 (0x0A1C)
Raised Program Started Event for Ad:ABC212D1, Package:ABC00126, Program: Cumulative update 3 - x86 client update install
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="ABC00126",ProgramID="Cumulative update 3 - x86 client update install", actionType 1l, value NULL, user NULL, session 4294967295l, level 0l, verbosity 30l
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="ABC00126",ProgramID="Cumulative update 3 - x86 client update install", actionType 1l, value , user NULL, session 4294967295l, level 0l, verbosity 30l
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
MTC task with id {8EB498C5-71D5-4933-BA80-6EEB8E189F98}, changed state from 4 to 5
execmgr 13/01/2015 6:56:04 PM
2588 (0x0A1C)
Program exit code 1642 execmgr
13/01/2015 6:56:04 PM 2784 (0x0AE0)
Could some please review and advise..
Thanks
RJ09

EHP 3 SP 1 failing with code 8 release 603

Hi,
I am doing an upgrade of ECC-DIMP, SAP-APPL and EA-APPL using SAINT on ERP 6. The procedure i have followed is to apply EHP 3 and apply SP 1 and 2 (inline with the ABAP SP level). The problem is that SAPK-60301INEAAPPL (EA-APPL) failed with a return 8 on TEST_IMPORT and the error messages it displays are
2EETW165 Function "API_RE_CD_GET_CASHFLOW_CN (RECD_API_CONDITION|01)" does not fit into the existing functi
on group "(RECD_BAPI_CONDITION|21)".
2 ETW167 Please transport the whole function group.
3WETW000 function module C14A_POPUP_CONFIRM_DELETE_INST (C14A|50) doesn't fit exactly into existing functio
n group (C14A|49); please repair it with the help of the modification assistant.
3WETW000 function module C1AY_WARNING_CHECK (C1AY|38) doesn't fit exactly into existing function group (C1A
Y|32); please repair it with the help of the modification assistant.
3WETW000 function module C1R2_REL_UPDATE (C1R2|21) doesn't fit exactly into existing function group (C1R2|2
2); please repair it with the help of the modification assistant.
3WETW000 function module C1R7_REL_UPDATE (C1R7|05) doesn't fit exactly into existing function group (C1R7|0
6); please repair it with the help of the modification assistant.
As a precondition step i have updated SPAM/SAINT to 29 and tp and R3trans are up to date.
These are extracted from the log at OS level. Does anyone know why this is occuring and is there a fix or an OSS note i need to apply?
Your help is very much appreciated.
Mani
Edited by: Mani on Aug 7, 2008 9:10 AM

Hi Mani,
I have faced the same problem during the upgrade of EHP2 of SAP_APPL and EA_APPL
in my case there was a transport request locked and i have unlock that request and then the installation went fine. So check there must be any request will be locked and u have to unlock that request
Hope this help
Regards
Subhash

2504 autoinstall fails with code 7.4.100.60 and 7.5.102

                   I am running into an autoinstall issue with our 2504 WLCs. Up to code version 7.2 I was able to use autoinstall to prime the WLCs by downloading the config from a TFTP server.
After upgrading to 7.4.100.60 the autoinstall fails because the WLC becomes unreachable after it received a DHCP address, gateway, option 150 and the bootfile. If I configure the controller manually, all is working as intended. Before upgrading to code version 7.4, we installed the FUS update 1.8 as described in the release notes.
The DHCP parameters are correctly handed out and I see the IP in the DHCP bindings with the management interface MAC. The WLC accepted all the parameters and in the console output the autoinstall is attempted as intended.
Pinging the DHCP - IP of the WLC is unsuccessful and thus the WLC cannot reach the TFTP server. A ping to a local broadcast shows 2 other clients (APs) on this segement but not the controller. The switch the WLC is connected to is a 3750 with IOS 12.2(58)SE2.
SW2#sho ip dh bin
Bindings from all pools not associated with VRF:
IP address          Client-ID/              Lease expiration        Type
                    Hardware address/
                    User name
10.80.1.57          f47f.35b6.9080          Mar 01 1993 04:40 AM    Automatic
10.80.1.126         0150.3de5.d9d4.e1       Mar 01 1993 04:58 AM    Automatic
10.80.1.127         01c8.9c1d.af2c.97       Mar 01 1993 04:59 AM    Automatic
SW2#sho arp | i 9080
Internet 10.80.1.57              0   f47f.35b6.9080 ARPA   Vlan8
SW2#sho run int g1/0/16
Building configuration...
Current configuration : 179 bytes
interface GigabitEthernet1/0/16
description WLC8-2504
switchport trunk encapsulation dot1q
switchport trunk native vlan 8
switchport mode trunk
spanning-tree portfast
end
I did not find anything in the bug navigator but this might be due to the fact that hardly anybody uses autoinstall.
Best
   Patrick

Hello Mario,
As per your query i can suggest you the following solution-
Please check the powering options-
• 802.3af Ethernet Switch
• Cisco AP2600 Power Injectors (AIR-PWRINJ4=)
• Cisco AP2600 Local Power Supply (AIR-PWR-B=)
and Power Draw
AP2600: 12.95W
Note: When deployed using Power over Ethernet (PoE), the power drawn from the power sourcing equipment will be higher by some amount depending on the length of the interconnecting cable. This additional power may be as high as 2.45W, bringing the total system power draw (access point + cabling) to 15.4W.
Hope this will help you.

Unattended driver installation fails with code 800b0109

hi there
i´m trying to install server 2012r2 unattended.
at the moment its failing while installing some driver.
the driver are signed and - as far i can see it - the signature chain is complete with no errors.
however - when i´m trying to install the driver (i´ve tried pnputil and devcon, or even manually) i get a message that the driver isnt trusted.
when i accept this message everythink is working - but its no unattended installation.
i´ve checked the setupapi.dev.log and found this:
! sig: Verifying file against specific (valid) catalog failed! (0x800b0109)
! sig: Error 0x800b0109: A certificate chain processed, but terminated in a root certificate which is not trusted by the trust provider.
i am willing and able to install the root certificate - but which one??
how can i find out which certificate is affected?
*edit*
it seems that disabling the testsigning via bcdedit is not longer working under 2012r2
or do i need more than one step?
thx
netlord

Hi,
If an unsigned or invalid boot-critical device driver is installed on an x64-based computer, the computer will not boot. The unsigned or invalid boot-critical device driver
will cause a Stop error.
If you trust this driver and trying to install this unsigned driver, use /ForceUnsigned to override the requirement that drivers installed on X64-based computers must have
a digital signature. For example,
Dism /Image:C:\test\offline /Add-Driver /Driver:C:\drivers\mydriver.INF /ForceUnsigned
The related KB:
Understanding Device Drivers and Deployment
http://technet.microsoft.com/en-us/library/dd744517(v=ws.10).aspx
Signing Device Driver Packages
http://technet.microsoft.com/en-us/library/cc771511(v=ws.10).aspx
Add and Remove Drivers Offline
http://technet.microsoft.com/en-us/library/dd744355(v=ws.10).aspx
More information:
Cross-Certificates for Kernel Mode Code Signing
http://msdn.microsoft.com/en-us/library/windows/hardware/dn170454(v=vs.85).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

User State Restore Fails with Error 0x8007000E

I am having some trouble restoring user states with usmt. I am running a side by side migration, for which I have already added the computer association prior to running the capture. The task sequence I am using is a very simple and only has
the following steps: Request State Store, Restore User State, and Release state store.
I am aware that the error code is linked to task sequence environment running out of space, and that it may have something to do with software updates. However, we are not currently deploying any software updates from SCCM. We do have an upstream WSUS
server that is supplying updates directly to clients. Would this still be an issue? I find it hard to believe that an OS deployment sequence runs just fine, but a very simple state restore errors out. Any thoughts?
Thanks,
Kyle

It looks like I'm getting two errors during the restore. First is that the COMPUTERNAME\unknown account is chosen for migration, but the target does not have account NEWCOMPUTERNAME\unkown. Directly after that is Failed.[gle=0x00000006]. Then
I get unable to create a local account because \lac was not specified and USMT error code 14. Below are the logs:
2015-03-12 11:23:51, Info [0x000000] LOADSTATE.EXE Version 6.3.9600.17237[gle=0x000000b7]
2015-03-12 11:23:51, Info [0x000000] USMT Started at 2015/03/12:11:23:51.094
2015-03-12 11:23:51, Info [0x000000] Command line: C:\_SMSTaskSequence\Packages\AHQ0000A\amd64\loadstate.exe \\ABBTECHCM01.ABBTECH.US\SMPSTOREd_FD7B8EBE$\ED83F415E21062DB9B2A8177AA933D6234B16FE457A8D193A0632650FCC769FB /decrypt /keyfile:****
/c /l:C:\Windows\CCM\Logs\SMSTSLog\loadstate.log /progress:C:\Windows\CCM\Logs\SMSTSLog\loadstateprogress.log /i:C:\_SMSTaskSequence\Packages\AHQ0000A\amd64\migdocs.xml /i:C:\_SMSTaskSequence\Packages\AHQ0000A\amd64\migapp.xml
2015-03-12 11:23:51, Info [0x000000] Script file specified: C:\_SMSTaskSequence\Packages\AHQ0000A\amd64\migdocs.xml[gle=0x000000cb]
2015-03-12 11:23:51, Info [0x000000] Script file specified: C:\_SMSTaskSequence\Packages\AHQ0000A\amd64\migapp.xml[gle=0x000000cb]
2015-03-12 11:23:51, Info [0x000000] Starting the migration process[gle=0x00000006]
2015-03-12 11:24:01, Info [0x000000] System information:
2015-03-12 11:24:01, Info [0x000000] Processing the settings store[gle=0x00000006]
2015-03-12 11:24:14, Info [0x000000] Selecting migration units
[gle=0x00000006]
2015-03-12 11:24:14, Error [0x000000] The account COMPUTERNAME\uknown is chosen for migration, but the target does not have account NEWCOMPUTERNAME\uknown. See documentation on /lac, /lae, /ui,
/ue and /uel options.
2015-03-12 11:24:14, Info [0x000000] Failed.[gle=0x00000006]
2015-03-12 11:24:14, Info [0x000000] Unable to create a local account because /lac was not specified[gle=0x00000006]
2015-03-12 11:24:14, Info [0x000000] USMT Completed at 2015/03/12:11:24:14.843[gle=0x00000057]
2015-03-12 11:24:15, Info [0x000000] ----------------------------------- USMT ERROR SUMMARY -----------------------------------
2015-03-12 11:24:15, Info [0x000000] * USMT error code 14:
2015-03-12 11:24:15, Info [0x000000] +-----------------------------------------------------------------------------------------
2015-03-12 11:24:15, Info [0x000000] | Unable to create a local account because /lac was not specified
I tried enabling the restore local accounts box, but that didn't work. Also the sequence runs just fine on a different model machine.

Photoshop CC installation fails with code EX20

The 64 bit version (WIN 7) stopped working, saying the internal file signature was invalid. To get past this I uninstalled PS and downloaded it again. This crashed during extraction with error code EX20. I now have no access to Photoshop. What can I do?

Hi mordecaiwebb,
Please follow this link, it mighr be useful for you:-
http://forums.adobe.com/message/5582179
Regards,
Rajshree

Uag server windows update failes with code Code 80072EE2

I am trying to do a windows update of my uag 2010 server, but keep getting an error of Code 80072EE2.
jason

Hi,
Could you try to set a winhttp config with this command : netsh winhttp
You can import your IE configuration or use a dedicated proxy.
More information about netsh winhttp on
http://technet.microsoft.com/fr-fr/library/cc731131(WS.10).aspx
Have a nice day,
Alex
Regards,
GIRAUD Alexandre MVP Forefront
[email protected]
GIRAUD Alexandre - MVP Forefront France http://www.alexgiraud.net/blog

OSD fails with 0x8007000e

Hello,
when trying to run OSD task, I get the following error: 0x8007000e
only happens on particular laptop computer (same task deploys successfully on another laptop model).
smsts.log
==========[ TsProgressUI started in process 1372 ]========== TsProgressUI 2013-10-14 17:15:30 1376 (0x0560)
Command line: "X:\sms\bin\i386\TsProgressUI.exe" /Unregister TsProgressUI 2013-10-14 17:15:30 1376 (0x0560)
Unregistering COM classes TsProgressUI 2013-10-14 17:15:30 1376 (0x0560)
Unregistering class objects TsProgressUI 2013-10-14 17:15:30 1376 (0x0560)
Shutdown complete. TsProgressUI 2013-10-14 17:15:30 1376 (0x0560)
Process completed with exit code 0 TSPxe 2013-10-14 17:15:30 1344 (0x0540)
Successfully unregistered TS Progress UI. TSPxe 2013-10-14 17:15:30 1344 (0x0540)
ExecuteSelectedTaskSequence(fpCallbackProc,pv,hCancelEvent), HRESULT=8007000e (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawizardcontrol.cpp,1527) TSPxe 2013-10-14 17:15:30 1344 (0x0540)
hrReturn, HRESULT=8007000e (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediaresolveprogresspage.cpp,445) TSPxe 2013-10-14 17:15:30 1344 (0x0540)
ThreadToResolveAndExecuteTaskSequence failed. Code(0x8007000E) TSPxe 2013-10-14 17:15:30 1344 (0x0540)
ThreadToResolveAndExecuteTaskSequence returned code 0x8007000E TSPxe 2013-10-14 17:15:30 1208 (0x04B8)
Setting wizard error: An error occurred while starting the task sequence (0x8007000E). For more information, contact your system administrator or helpdesk operator. TSPxe 2013-10-14 17:15:30 1208 (0x04B8)
ResolveProgressPage::OnWizardNext() TSPxe 2013-10-14 17:15:30 1208 (0x04B8)
Activating Finish Page. TSPxe 2013-10-14 17:15:30 1208 (0x04B8)
Loading bitmap TSPxe 2013-10-14 17:15:30 1208 (0x04B8)
Exiting task sequence wizard. TSPxe 2013-10-14 17:15:43 1208 (0x04B8)
Exiting with return code 0x00000000 TSPxe 2013-10-14 17:15:43 1208 (0x04B8)
Execution complete. TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
hMap != 0, HRESULT=80070002 (e:\nts_sccm_release\sms\framework\tscore\environmentscope.cpp,515) TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
m_pGlobalScope->open(), HRESULT=80070002 (e:\nts_sccm_release\sms\framework\tscore\environmentlib.cpp,337) TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
this->open(), HRESULT=80070002 (e:\nts_sccm_release\sms\framework\tscore\environmentlib.cpp,549) TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
::RegOpenKeyExW (HKEY_LOCAL_MACHINE, c_szSMSTSKey, 0, KEY_READ, &hSubKey), HRESULT=80070002 (e:\nts_sccm_release\sms\framework\tscore\utils.cpp,258) TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
RegOpenKeyExW failed for Software\Microsoft\SMS\Task Sequence TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
GetTsRegValue() failed. 0x80070002. TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
End program: TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
Finalizing logging from process 736 TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
Finalizing logs to root of first available drive TSBootShell 2013-10-14 17:15:43 752 (0x02F0)
Successfully finalized logs to C:\SMSTSLog TSBootShell 2013-10-14 17:15:44 752 (0x02F0)
Cleaning up task sequencing logging configuration. TSBootShell 2013-10-14 17:15:44 752 (0x02F0)

Hi,
In the hope of helping others avoid the lengthy troubleshooting and searching we've been through...
I recently had this error on our OSD reference image task sequences. We eventually found the solution (after a couple of days trawling the net) on Niall Brady's web site.
URL amended to be able to post - remove spaces :)
www . niallbrady . com /2013/05/17/after-selecting-a-task-sequence-in-configuration-manager-2012-sp1-you-receive-threadtoresolveandexecutetasksequence-failed-code0x8007000e-in-smsts-log/
The basic cause is that we update our ref image every 3 months with the latest updates applicable via SUP (Software Update Point) and the amount of deployed updates to the collection containing the reference image Virtual Machine had grown too large.
The resolution for us was to delete all of the old SUP packages targeted to the reference build collection (or remove all of those deployments), and only use the latest created package/group.
I guess if you don't include updates in your base reference image, you may run into this issue with all Task Sequences, not just the reference image TS. One to watch for which is not at all obvious.
Could it be that the original poster had that particular machine in a collection that had too many SUP packages deployed to it?

Installing Production Premium CS6 - Prelude failed - exit code 6

Hi
Is this the official method for reporting installation problems of new applications?
I have just installed Production Premium CS6 - I received an error message at the end (see below) that Prelude failed to install - All other apps installed ok
Can anyone help or direct me to where I should be asking this question
Would also be interested to know what all the warnings mean. I currently have CS5 and CS5.5 trail installed.
Many thanks
Chris Anderson
Exit Code: 6
Please see specific errors and warnings below for troubleshooting. For example, ERROR: DF012, DW063 ... WARNING: DS013 ...
-------------------------------------- Summary --------------------------------------
- 0 fatal error(s), 4 error(s), 8 warning(s)
WARNING: DS013: Payload {D5B1535A-FDFC-4B40-B2E2-21DA83D9CB57} Adobe Audition 4.0.0.0 is already installed and the session payload {30FD541D-3C9D-41C4-B240-A994EE4E0231} Adobe Audition 5.0.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Payload {CCB778B5-25B8-4E57-9F20-72B11B443EF9} AmericanEnglishSpeechAnalysisModels 2.5.0.0 is already installed and the session payload {C5CA53A2-E722-4D76-B5AC-71522CC48AB3} AmericanEnglishSpeechAnalysisModels 3.0.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Payload {CD693E49-C5EF-4FA6-9037-9B636931C02B} AmericanEnglishSpeechAnalysisModels 1.0.0.0 is already installed and the session payload {C5CA53A2-E722-4D76-B5AC-71522CC48AB3} AmericanEnglishSpeechAnalysisModels 3.0.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Payload {3BF96AC2-0CA1-11DF-B07B-459956D89593} AdobeHelp 1.0.0.0 is already installed and the session payload {D38116C8-C472-4BB0-AD6F-0C1DD1320D1D} AdobeHelp 4.0.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Payload {7EABC54B-02C3-4DA1-9EB4-974CE7414066} AdobeHelp 3.4.0.0 is already installed and the session payload {D38116C8-C472-4BB0-AD6F-0C1DD1320D1D} AdobeHelp 4.0.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Payload {1A1E5FF9-D0FD-42A3-8E18-E5E7E95E1AB4} DynamiclinkSupport 5.5.0.0 is already installed and the session payload {DE88AA40-6766-43D3-A755-8FC374B3D2C3} DynamiclinkSupport 6.0.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Payload {A8798E04-96FF-4564-9157-0D4C89CB794C} DynamiclinkSupport 5.0.0.0 is already installed and the session payload {DE88AA40-6766-43D3-A755-8FC374B3D2C3} DynamiclinkSupport 6.0.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Checking payloads upgrade/conflict relationships : Failed with code 1
----------- Payload: {E0D1B182-6827-4AD8-9C1D-CFFD4314DFE4} Adobe Prelude CS6 1.0.0.0 -----------
ERROR: DF012: Unable to locate file at "K:\adobeTemp\{E0D1B182-6827-4AD8-9C1D-CFFD4314DFE4}\_1097_9268d9a8cb704e8d07ade70cfd1a58 c7"(Seq 1044)
ERROR: DW063: Command ARKMoveFileCommand failed.(Seq 1044)
ERROR: DW050: The following payload errors were found during install:
ERROR: DW050: - Adobe Prelude CS6_AdobePrelude1en_USLanguagePack: Install failed
ERROR: DW050: - Adobe Prelude CS6: Failed due to Language Pack installation failure
System Requirements

Hi Jeff,
I contacted adobe support chat. I had installed on drive K to keep programs from the main o/s drive. TThe tech support chap said I should install always on drive C to avoid the errors.
I dont understand why this hould be, but i did it and all ok now - no errors.
I wonder why the install program gives you the option of installing on any disk when you can only use the o/s disk
Thanks
Chris Anderson

Installation of Photoshop update 13.1.2 for creative cloud fails with error code U44M1P7 I need help

I need help installing update 13.1.2 for Photoshop creative cloud, installation fails with error code: U44M1P7. Could someone please help?

Sorry to bother you.
I could find the answer after searching previous posts about this language problem.
Had to change my language in AAM profile and then download PS CS6 again ( english version ).
Then open the actual Photoshop and in preferences > interface you can besides the Dutch also option for English.
restart application and Voila.
Greetz, Jeroen

Failed with code 0x8007000e.

Similar Messages

Maybe you are looking for