Failover lan unit (name)

During an Internet upgrade, I changed the roles of my ASA's. The site that was originally designedf to be Secondary is now a better fit as Primary.
So, what used to be my Secondary ASA is now my Primary. Howvere, the command "failover lan unit secondary" was set on the Secondary unit and
failover lan unit Primary was set on original Primary device.
Can I change these to reflect the correct role "failover lan unit Primary or Secondary" without causing any outages or problems??

Jatin
Thnaks for your response.
At the time we did issue a command that made the secondary ACTIVE. So now I have the following:
(I have modified IP's to remain anonymous)
ASA-5520# sh failover
Failover On
Failover unit Secondary
Failover LAN Interface: Heartbeat GigabitEthernet0/3 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 160 maximum
Version: Ours 8.2(3), Mate 8.2(3)
Last Failover at: 13:43:59 CST Dec 21 2012
This host: Secondary - Active
                Active time: 17894886 (sec)
                slot 0: ASA5520 hw/sw rev (2.0/8.2(3)) status (Up Sys)
                  Interface outside (216.x.x.2): Normal
                  Interface inside (192.168.x.1): Normal
                  Interface dmz (192.168.x.1): Normal (Not-Monitored)
                  Interface management (192.168.x.84): No Link (Waiting)
                slot 1: empty
        Other host: Primary - Standby Ready
                Active time: 5267283 (sec)
                slot 0: ASA5520 hw/sw rev (2.0/8.2(3)) status (Up Sys)
                  Interface outside (216.x.x.12): Normal
                  Interface inside (192.168.x.2): Normal
                  Interface dmz (192.168.x.2): Normal (Not-Monitored)
                  Interface management (0.0.0.0): No Link (Waiting)
                slot 1: empty
I also modified the ip route statements to make the Internet router connecting to what is currently called the Secondary as my default toute out to world.
          route outside 0.0.0.0 0.0.0.0 216.x.x.11 1 track 1
          route outside 0.0.0.0 0.0.0.0 216.x.x.1 254
I simply want the ASA I am using as Primary to be called the Primary. What would you/anyone advise?

Similar Messages

Is it possible to display in a front panel indicator the units name (for instance, N "Newtons" or ºC) from a virtual channel that you previously defined using MAX?

If possible, how can I do it?
Thanks in advance With LabVIEW 6 it is clear that we can display the DAQ channel name of previously defined virtual channels, so it seems to be possible that we would be able to access to other information defined in MAX as channel units name...
Thanks

Yes it is possible.
Locate the LLB:
LV folder\vi.lib\daq\dqchnutl.llb
There you find useful vis to handle virtual channel.
The Get DAQ ChannelNames.vi return also the channel units

Fetch the operating unit name based on the country name

Hi all,
I want to fetch the operating unit name based on the country name, there is no link between fnd_territories(_tl) and hr_all_organization_unis(_tl) tables.
Can any one know how to get this thing.
any help or idea is appreciable.
Thanks,
Giri

Giri,
I don't think you will find such a link. One country can be used by multiple operating units.
Hope this helps,
Sandeep Gandhi

Duplicate persistence unit name in war

Hi!
I am using weblogic 10.3.
I am trying to deploy a spring web application with two jars, that contain jpa entities with a persistence.xml. The persistence unit name in both persistence.xml is equal. That is for spring no problem, because i wrote a PersistenceUnitManager, that merges both persistence units into one.
So far so good. But weblogic cant't deploy the war, because while validation of the deployment, wls throws an exception, that there are two persistence unit with the same name.
Does anybody has an idea how to deploy this war?
Can i switch off the validation of the persistence.xml?

Thanks for the response James.
I'm using hibernate as my JPA provider. I'm not sure if weblogic is first loading it's own jpa implementation and management, and getting confused with mine. How could I check this ?
I did however create a weblogic.xml in my web-inf folder, with the following property
<weblogic-web-app>
<container-descriptor>
<prefer-web-inf-classes>true</prefer-web-inf-classes>
</container-descriptor>
</weblogic-web-app>
Here is the full stack trace:
Hi!
I am using weblogic 10.3.
I am trying to deploy a spring web application with two jars, that contain jpa entities with a persistence.xml. The persistence unit name in both persistence.xml is equal. That is for spring no problem, because i wrote a PersistenceUnitManager, that merges both persistence units into one.
So far so good. But weblogic cant't deploy the war, because while validation of the deployment, wls throws an exception, that there are two persistence unit with the same name.
Does anybody has an idea how to deploy this war?
Can i switch off the validation of the persistence.xml?
Any ideas ?
Thanks,
John

Elimination of unit name in Query

Hello,
when I create the Query where in colums are key figures I always also unit name e.g. EUR for currency, or H for hour. I can only remove this to the top of the column, but I can´t eliminate completely.
Do you have some advices?
Thanks
Petr

Hi
Create a new forumla
under data functions select the no dimensions NODIM option
insert the keyfigure for which unit should not be displayed
Now it will not display the units in the report.
Regards
RaM

Creation of Product :technical abbreviation of the software unit name

Hi All,
I am trying to create a new SWCV in SLD and after entering the initial product name,version and vendor , Iam asked to
"Enter the technical abbreviation of the software unit name"
I further see that this gets listed as "Software unit".
Whats the importance of this field and also what would be the typical values ?
Thanks in advance!
vittal

Thanks Prateek,
Did you mean by "Technical abbreviation " same as the SWC or the SW Product ? Cos SW Product is collection of SWC ?
I have given Technical abbreviation as SWC itelf.. BUt When I see the various software unit in the ProductA , I find 2 entries even though I have created only one.
1.ProductA : (default )
2.ProductA: SWC (this is one i have created )
Kindly clarify?
regards
Vittal
Edited by: Vittal Navale on Nov 4, 2008 11:10 AM

10.4.8 Server Admin will not generate CSR with unit name containing "/"

I work in a University and our Computer Store is a reseller for Thawte SSL certs. The "Organizational Unit" that my department was assigned is "Outreach Technology Services/World Campus", but when I try to generate a CSR for one of our Web sites, the Organizational Unit gets truncated to just "Outreach Technology Services" which my reseller won't accept as my Organizational Unit name.
How can I get around this?
I am running 10.4.8 Server.

No the, the gui field is showing the full name "Outreach Technology Services/World Campus" but when I submit the CSR to the department that handles these, they use openssl req -noout -text -in test.csr to view the contents.
Certificate Request:
Data:
Version: 0 (0x0)
Subject: CN=secure.worldcampus.psu.edu, O=The Pennsylvania State University, OU=Outreach Technology Services/World Campus, C=US, ST=Pennsylvania, L=University Park
Subject Public Key Info:
Public Key Algorithm: rsaEncryption
RSA Public Key: (1024 bit)
Modulus (1024 bit):
00:cf:f2:a7:e8:56:38:71:61:af:d1:29:1d:0d:37:
a5:5f:18:be:01:99:37:0d:db:45:1e:20:89:9f:33:
ff:be:fe:be:f0:25:b2:c0:44:08:56:d3:71:57:c1:
1d:87:2d:5e:54:99:07:13:23:58:26:93:e7:06:d2:
50:5f:b5:15:dc:69:76:09:62:02:39:e1:61:d2:9e:
3e:a8:ea:20:7a:49:97:eb:a4:ed:80:24:2b:9f:4f:
39:0e:40:cb:4c:46:0f:e3:5f:2f:73:d5:81:80:ed:
fa:08:21:5f:c4:a8:84:b1:6a:d8:3e:6b:e3:a3:08:
7c:77:b0:d0:82:c4:09:35:a7
Exponent: 65537 (0x10001)
Attributes:
a0:00
Signature Algorithm: sha1WithRSAEncryption
af:bb:0b:42:43:b1:f0:82:e4:62:c7:f7:cc:eb:8b:1e:56:fa:
1b:63:db:a4:2e:1c:07:b3:00:ff:fa:42:3b:4a:8c:7c:de:e0:
1e:f1:87:d7:44:0f:99:99:b6:a1:89:77:93:a4:d0:48:2f:7e:
d3:5d:95:e6:3e:4e:29:67:36:a4:60:00:17:a2:45:c5:28:87:
aa:01:5c:bb:20:62:05:09:a5:e5:11:e0:10:b7:96:0e:c1:2e:
bb:dd:7a:d6:4e:61:8d:d3:ae:41:54:27:8a:3f:d9:ab:bb:37:
6e:5a:28:f0:7d:a7:ac:cd:37:4f:7c:57:97:14:7e:ad:c0:c7:
e4:64
But it looks like that /World Campus is there, so It must be their .cgi that is unable to handle the "/"
So NEVER MIND. I should have checked the contents first.

Cons Unit name in UCMON different than in UCWB

Dear team,
I've a question concerning master data of cons unit . Following issue appears:
I know that cons unit is time dependent: the old cons unit name was only valid until 31.12.2009. After this date there are several entries with different valid to dates, but medium and also long name never changed afterwards.
Example:
ConsUnit --- Valid from --- Valid to - long name- medium name
3456 --- 01.12.2009 --- 31.12.2009 --- Old LE name long --- Old LE name
3456 --- 01.01.2010 --- 31.03.2010 --- The new name in long --- New name
3456 --- 01.04.2010 --- 30.04.2010 --- The new name in long --- New name
3456 --- 01.05.2010 --- 31.05.2010 --- The new name in long --- New name
3456 --- 01.06.2010 --- 31.12.9999 --- The new name in long --- New name
If I go thru ucwb --> master data --> consolidation units --> 3456, then I see the following entries:
Name
Medium: New name
Long: The new name in long
So I do see the latest valid entries in ucwb and I assumed to see the same in UCMON. But if I open ucmon for instance for period 005/2010 I see that the old name is displayed instead of the new name. Curious is that if I click on "filter unit" in ucmon that I then get the corret name in the filter menu - but only there! Unfortunately, I still get the old name in the monitor even though the filter menu shows the new name.
Do you've any suggestion how I can solve this issue or what might be the reason for the different names in UCMON and UCWB?
Thanks in advance for your help!
Best Regards,
Daniel

This sounds like a minor bug. I suggest you search SAP Notes for solution and if none is found notify SAP via customer message.

Failover Cluster Network Name Failed and Can't be Repaired

I have an issue that seem to be a different problem than any others have encountered.
I've scoured everything I can find and nothing has fixed my problem.
The problem starts with the common problem of the cluster network name failing on my 2 node server 2012 file server cluster. The computer object was still in AD and appeared to be fine so it was not the common problem of the object
getting deleted somehow. At the time, there was no other object with that name in the recycling bin, so I don't think it was mistakenly deleted and quickly recreated to cover any tracks, so to speak.
Following one guide, I tried to find the registry key that corresponded with the GUID of the object, but neither node in the cluster had it in its registry (which may be part of the problem).
Since it was in the failed state, I tried to do the repair on the object to no avail.
We run a "locked down" DC environment so all computer objects have to be pre-provisioned. They were all pre-provisioned successfully and successfully assigned during cluster creation. The cluster was running with no issues for a month
or so before this problem came up.
When I do a repair on the object while taking diagnostic logs the following 4609 error appears:
The action 'Repair' did not complete. - System.ApplicationException: An error occurred resetting the password for 'Cluster Name'. ---> System.ComponentModel.Win32Exception: Unknown error (0x80005000)
There appears to be a corresponding 4771 error with a failure code 0x18 that comes from the security log of the DC that states there was a Kerberos pre-authentication failure for the cluster network name object (Domain\Clustername$)
I believe this is what is causing the repair failure. All the information I found related to security error 4771 was either a bad credentials given for a user account or the fix was to reconnect the computer to the domain. I can't seem to find
a way to do this with the cluster network name. If there's a way please let me know.
I've tried a number of things, like resetting the object, disabling it, deleting and creating a new object with the same name, deleting that new object and recovering the original, etc...
Can anyone shed some light on what is going on and hopefully how to fix it other than rebuilding the cluster? I'm quite close to just tearing it down and building it back up but am hesitant because this cluster in currently in production...
Any help would be appreciated

Hi,
I don’t find out the similar issue with yours, base on my experience, the 4096 error
often caused by the CSV disk issue, and the 0x80005000 error some time caused by the repetitive computer object in OU. Please check the above related part or run the validate test then post the error information.
Although I do have a CSV, there doesn't seem to be any problems with it and it was running just fine for a month or so before the problem started. I double checked and there is no duplicate computer objects, maybe I don't understand what you mean by
repetitive, could you explain further?
The cluster validates successfully with a few warnings:
Validating cluster resource Name: DT-FileCluster.
This resource is marked with a state of 'Failed' instead of
'Online'. This failed state indicates that the resource had a problem either
coming online or had a failure while it was online. The event logs and cluster
logs may have information that is helpful in identifying the cause of the
failure.
- This is because the cluster name is in the failed state
Validating the service principal names for Name:
DT-FileCluster.
The network name Name: DT-FileCluster does not have a valid
value for the read-only property 'ObjectGUID'. To validate the service principal
name the read-only private property 'ObjectGuid' must have a valid value. To
correct this issue make sure that the network name has been brought online at
least once. If this does not correct this issue you will need to delete the
network name and re-create it.
- This is definitely related to the problem and the GUID probably got removed when we attempted a fix by resetting the object and trying the repair from the failover cluster manager.
The user running validate, does not have permissions to create
computer objects in the 'ad.unlv.edu' domain.
- This is correct, we run a restricted domain. I have a delegated OU that I can pre-provision accounts in. The account was pro-provisioned successfully and was at one point setup and working just fine.
There are no other errors nor warnings.

Need to get the operating unit name for AP report

Hi,
I'm really new to XML/BI publisher. I have to customize a oracle report called Payables Posted Payment Register. The package XLA_JELINES_RPT_PKG ties into this report. Upon reading the package it's pretty confusing. Anyway, there is a parameter called P_SECURITY_ID_INT_1 which is the operating unit. I'm trying to display the operation unit in my report but it only returns the operating unit id and I need the name of the operationg unit. So I'm guessing im going to need to grab it somehow in the XLA_JELINES_RPT_PKG. Is this correct? Any suggestions on the best approach?
Thank you!! Your help is so much appreciated!

Hi,
after time elavualtion use t code PT66, in this t.code double click on the each month(period) then you can get the internal table like ZES, SALDO, ZKO. again double click on the each internal table, you can get the information through the time types. Like , now you want the overtime hours, 0903, 0904 with this time types you can get the each employee no. of. overtime hours.
ZL, ZES, SALDO, TIP entries are internal table , you could not get any results from this table with using se11, se16.
With PT_BAL00 with this report also we can get the overtime hours with the help of time events.
Good luck
Devi

WORKFLOW, organisational unit name

Hi,
I am making use of FM 'SAP_WAPI_WORKITEM_RECIPIENTS' with input as workitem id and user name. I am getting the organisational unit, but the problem is it gives only the number of the organisational unit.
Is there any FM which after giving the organisational unit number will give me the description/short text for the organisational unit.
Report 'RHSHOWOR' gives the description, but it takes the user name only and shows all the org unit specified for the user, I want the description for a single org unit.
Relevant answers will be rewarded.
Thanks in advance.
Regards,
Neerup.

Thanks for the quick reply.
The table T527X does not exist in my system.
I am checking other stuffs from the link : http://help.sap.com/saphelp_nwpi71/helpdata/en/c5/e4b239453d11d189430000e829fbbd/frameset.htm
Is there any standard SAP provided FM, which will give me the description, or can you please suggest some other table.
Thanks and Regards,
Neerup.

ALE: Org unit name not in first field

Hi All,
We are maintaining our CRM org structure from R/3 and are getting close to implementing our system and have come accross a problem.
When the BP is created (in CRM) for the Org units it puts the code of the org unit in the first line of the 'Name' field and then the description on the second line..
The problem with this is when you select the BP through the Web IC it just displays the code, which is no good to the call centre staff as it is (to them) meaningless.
I have been through our config and can't find where this information is mapped to the BP.
Any help greatly appreciated and points rewarded as always..
Cheers
Gaz

Hi All,
The only way this seems to be possible is to ammend the data through a BADI...
I have implemented the PARTNER_UPDATE BADI and done a call to 'BUPA_GENERAL_CALLBACK' to get the information I need and then 'BUP_MEMORY_BUT000_FILL' to update the information.
The problem is that this information isn't being populated back to the BP itself (no changed from the BADI code).
You cannot do a COMMIT WORK as it causes an error..
Is there another FM that will save the changed values ???
Many Thanks in advance
Gaz

How to read employee user's Org unit name,Org unit add and user position

Hi ,
Is there any Function module or a class-method to read a user assinged Orgunit name ,Org unit address and the user position at that org unit.
i have a given out a search on sdn but could not get the answer.
Thanks for your time
Seema

Eswar,
Thanks for your fast reply.
I found this table before.But i do not have idea of passing what paramters to get my specific org and position of an employee data from this table.
Let say i know my BP number for employee and Username of him.
i could find out his Obj id using EMP user name.
When i look into table HRP1001 using above Obj id, i could see there are 3 entries exist in table , among one of them is talking about position as
Sclas = S and SOBID = 50020832.
So how would i know by having this number , is it dealing with position and what kind of position it is,,,whether a manager or something else?
Hope you got me.
Basically am aslo looking for a FM where in i cold porvide aBP number or EMP username, where inturn i ll get a Emp position his org details.
Seema
Edited by: seema rajjot on Apr 9, 2010 8:40 PM

2012R2 hyper-v failover cluster Cluster name object has no DNS record created

I’m trying to setup a 2-node ws2012R2 cluster using ws2008R2 AD(with DNS) but got an issue with DNS entry creation on AD. I also tried ws2012 AD but it's the same problem.
The individual node DNS entries were created on AD automatically upon joining AD but I can’t get AD to create DNS entry for my cluster name object automatically. AD will have cluster name computer
created but no record for cluster name in DNS entries
Got the following event ID 1196 error with the info below.
Cluster network name resource 'Cluster Name' failed registration of one or more associated DNS name(s) for the following reason:
DNS server failure.

Hi hjma29,
How about your issue now? I just want to confirm the current situations.
Please feel free to let us know if you need further assistance.
Regards.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Need to "move" failover to different interface/port

Sorry if this is the wrong area, we have so seldom had questions that were not otherwise handled I don't frequent this area.
How difficult is it to change the interface used for active/standby failover? It's a working, already configured pair with standby, but I need to move the crossover cable and tell them to use a different interface.
ASA 5510 pair, already set up and working with failover that was originally configured on Ethernet port 0/3 by the senior network admin. It appears that from his use of interfaces or ports he used things straight out of examples on the web, including the interfaces used.
The senior network admin retired last spring and left me "in charge", gee, thanks.
I need to make some changes and need an Ethernet port for a new important project.
The Management 0/0 interface is unused and shutdown. We manage via inside interface from a specific subnet inside so don't need the dedicated management interface.
I want to move failover FROM Ethernet 0/3 TO Management 0/0
*This is the current setup:
Result of the command: "sh run failover"
failover
failover lan unit primary
failover lan interface failover Ethernet0/3
failover link failover Ethernet0/3
failover interface ip failover 169.254.255.1 255.255.255.252 standby 169.254.255.2
*And this is the current interface configuration for 0/3 and Management:
interface Ethernet0/3
description LAN/STATE Failover Interface
interface Management0/0
speed 100
duplex full
shutdown
nameif management
security-level 0
no ip address
ospf cost 10
I know it can run on the Management 0/0 interface because I see a lot of "how to configure" as if the ASA is brand new and several examples out there indeed show it being setup on Management.
I'm looking for how to take an ASA pair that is currently configured and has a working functional failover configuration and simply "move failover" to a different hole or change the interfaces used for the "heartbeat" as it were.
I assume it's not hard - but I also assume there's a specific sequence of events that must take place to prevent the pair from going into failover and switching lead roles...........
For example - would I shut off or turn off failover, and if so how, and on which ASA (frankly, I'm not sure how to access the secondary or standby if this must be done from or on the standby unit as I've never done that "deep" a config before)
CLI is fine - I'd be just as comfortable in either ASDM or cli.
I sure hope this makes sense - I'm more of a troubleshooter and fixer than a designer or network engineer....
And many many thanks - getting this moved will free up the interface I need and can really make a big dent in my project list while the supervisor is on vacation this week! I'd love to have this done and working before his return.
Oh, in case it does matter as I've been told, this is the Currently running license and versions shown here:
Cisco Adaptive Security Appliance Software Version 8.4(4)1
Device Manager Version 6.4(7)
Compiled on Thu 14-Jun-12 11:20 by builders
System image file is "disk0:/asa844-1-k8.bin"
Config file at boot was "startup-config"
VRDSMFW1 up 141 days 4 hours
failover cluster up 141 days 4 hours
Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xfff00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.06
Number of accelerators: 1
0: Ext: Ethernet0/0 : address is 0024.972b.e020, irq 9
1: Ext: Ethernet0/1 : address is 0024.972b.e021, irq 9
2: Ext: Ethernet0/2 : address is 0024.972b.e022, irq 9
3: Ext: Ethernet0/3 : address is 0024.972b.e023, irq 9
4: Ext: Management0/0 : address is 0024.972b.e01f, irq 11
5: Int: Not used : irq 11
6: Int: Not used : irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 100 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
VPN-DES : Enabled perpetual
VPN-3DES-AES : Enabled perpetual
Security Contexts : 2 perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : 250 perpetual
Other VPN Peers : 250 perpetual
Total VPN Peers : 250 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
This platform has an ASA 5510 Security Plus license.
Failover cluster licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 100 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
VPN-DES : Enabled perpetual
VPN-3DES-AES : Enabled perpetual
Security Contexts : 4 perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 4 perpetual
AnyConnect Essentials : 250 perpetual
Other VPN Peers : 250 perpetual
Total VPN Peers : 250 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 4 perpetual
Total UC Proxy Sessions : 4 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
This platform has an ASA 5510 Security Plus license.
Serial Number: ABC12345678
Running Permanent Activation Key: eieioandapartridgeinapeartree
Configuration register is 0x1
Configuration last modified by me at 15:03:07.132 CDT Mon Sep 15 2014

If there was a "smack-self-on-forehead" icon here I'd use it now.
Of course, totally logical - if you disconnect a monitored connection on the standby it's not about to take over as primary because it's had a failure and can't do the job, forcing the primary or active to remain that way. There's the key that would allow all other changes.
Since the settings or config lines are in place already, then if I'm correct it's a matter of then just modifying what's there, and of course removing the name of the Management interface (no nameif) and making sure it's not shut down (no shutdown), etc.
You are a handy person to have around. Thanks.
By the way, *thanks to prior answers received here* and reading responses to others who had questions I can say I've set a record for this agency and done what no one else had been able to do - I've taken a troublesome LAN-to-LAN connection and made it trouble-free with a solid connection that is just 7.5 hours away from being up 90 days with no interruption, no collapse of any SA and improved performance. I have 2 others out of our 34 that aren't too far behind that. The boss has recognized this after seeing his monthly up-time reports.
Once I get this done failover change made I will be setting up a "DMZ" of sorts and trying out my hand at telling the 5510s to forward specific traffic aimed at a specific public IP address to a specific server. (But that's another topic............)

Failover lan unit (name)

Similar Messages

Maybe you are looking for