Failover to redundant box shows Redundancy Protocol: Not Running on CSS

After failover to redundant (backup) BOX, the backup BOX becomes Master but output of âsh redundancyâ shows Redundancy Protocol: Not Running and shows intermittent packet drops.

Here is the URL for the configuration for the Configuring VIP and Virtual IP Interface Redundancy follow the configuration guide which may help you http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11500series/v7.10/configuration/advanced/guide/VIPRedun.html

Similar Messages

IP Protocol not running

I am setting up 2 aironet 1310's. I am connecting them to my NIC to configure instead of placing them ont he network. I am able to assign an IP address, however, when I ping, I get a "Protocol not running" error. If I type ping <enter><enter> i get "unknown protocol."
I have never encountered this befor...???

Hi
It means you don't have a proper IP address configured I guess - have you put the iP address on the ethernet interface?
It's normally put on the Int BVI1... try that.
Regards
Aaron
Please rate helpful posts...

Svrcfg show Job Server not running

Hi,
I am currently running Data Services 12.1.1.0 on Linux RH AS 4.6. I have noticed an issue and wondering whether there is something I am doing wrong.
I installed DS and configured the JS. I have successfully started, stopped and started this again, via the svrcfg utility and it clearly states "running". Then I log out of Putty and log back into the into server hosting DS. When I go to the svrcfg utility again, go to control job server it reports a status of not running. If I exit the tool and type ps -fu <username> I can see my Job Servive/Engine as I would expect and jobs still run fine?
Does anyone know what might be causing this?
Thanks
Chris

Hi,
I am also getting the same issue. If you login into putty and check the status by which terminal you have started shows "RUNNING", if you login through another session with same user it shows "NOT RUNNING".
Output of ps -o user,fname |grep -v grep|grep AL_JobSe is
bodi AL_JobSe
I am running the . .al_env.sh manually (not from profile!).
Thanks
Maran

Task scheduler is showing success but not running job

Hello, I have a relatively simple .net application that I realized when ran through the Task Scheduler of a Windows 2008 R2 server it shows in the status that i completed successfully but apparently did not run at all from looking at the log file.
When I just manually execute this program it runs perfectly fine. I am using myself as the user to run this task and have full permissions.
I also tried a test batch file that just echos some text into a text file. Same issue.... shows that it runs ok in task scheduler but doesnt do anything while running it manually works fine.
Any ideas of what could be causing this? thanks

Hi Nehemiah,
I ran the test batch file as below and work without issue:
@echo This is a test> d:\test.txt
And this is my setting:
If there is anything else regarding this issue, please feel free to post back.
Best Regards,
Anna Wang
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Apps show but will not run after sync

iPod Touch 4th generation updated to version 4.3.2(bh7)
last night, sync went well. Today all apps appear but will not run they just flash like they are trying to run. System goes back to main screen.

Hi,
Welcome to Apple Discussions!
Try a hard reset of your iPod: Press/hold the home and sleep/wake buttons until the Apple logo appears.
Hope this helps!

I am having issues with parts of my Facebook news page not showing and games not running.

For the last three days, I have been having issues running Facebook on Firefox. First, the side panels on the news page are not showing, which means I cannot connect to games like Farmville or Bejeweled Blitz. Those side panels were showing the previous two days, but when trying to connect, I had a message about the secure setting and I would get the message "you are no longer logged onto FB, connect to FB to play".

Try clearing cache and cookies. Next make sure your plug-ins are up to date. If both do not resolve you issue try [[Safe mode]]
If you issue is resolved by this post please click Solved it! so we can assist others.

VIP Is not Running

Hi,
I have this problem on Oracle RAC 10g, the ip private don't answer, then i execute svrctl status nodeapps -n myserver, this show :
VIP is not running on node: SVRRAC02
GSD is running on node: SVRRAC02
PRKO-2016 : Error in checking condition of listener on node: SVRRAC02
ONS daemon is running on node: SVRRAC02
What can i do???

Ok, i execute this crs_stat -t
Name Type Target State Host
ora....D1.inst application ONLINE ONLINE svrrac01
ora....D2.inst application ONLINE ONLINE svrrac02
ora.HR9PRD.db application ONLINE ONLINE svrrac02
ora....01.lsnr application ONLINE OFFLINE
ora....c01.gsd application ONLINE ONLINE svrrac01
ora....c01.ons application ONLINE ONLINE svrrac01
ora....c01.vip application ONLINE ONLINE svrrac01
ora....02.lsnr application OFFLINE OFFLINE
ora....c02.gsd application ONLINE ONLINE svrrac02
ora....c02.ons application ONLINE ONLINE svrrac02
ora....c02.vip application ONLINE OFFLINE
But the error continue VIP is not Running
The Next Command i cann't execute now because this stop the services and i am on production, in the night i execute this activity.
Thanks.

Unable to issue "redundancy-protocol" command on CSS

This is really weird. I've done box-2-box redundancy on CSSs half a dozen times. I have a CSS 11050 on 5.0(33) code that does not recognize "redundancy-protocol" as a valid command on the VRRP interface.
Config of the CSS is really basic:
!Generated on 01/01/1980 00:00:11
!Active version: ap0500033
configure
!*************************** GLOBAL ***************************
bridge spanning-tree disabled
persistence reset remap
acl enable
ip redundancy
app
app session 192.168.1.2
ip route 0.0.0.0 0.0.0.0 14.60.64.1 1
!************************* INTERFACE *************************
interface e1
phy 100Mbits-FD
interface e2
bridge vlan 2
phy 100Mbits-FD
interface e3
phy 100Mbits-FD
interface e4
phy 100Mbits-FD
interface e5
phy 100Mbits-FD
interface e6
phy 100Mbits-FD
interface e8
phy 100Mbits-FD
bridge vlan 10
!************************** CIRCUIT **************************
circuit VLAN1
redundancy
ip address 14.218.74.110 255.255.254.0
circuit VLAN2
redundancy
ip address 14.60.64.211 255.255.248.0
circuit VLAN10
ip address 192.168.1.1 255.255.255.0
!************************** SERVICE **************************
service tempest
ip address 14.218.74.127
keepalive type http
keepalive uri "/checkServerStatus.html"
active
service tempest-ping
ip address 14.218.74.127
active
service zephyr
ip address 14.218.74.128
keepalive type http
keepalive uri "/checkServerStatus.html"
active
service zephyr-ping
ip address 14.218.74.128
active
!*************************** OWNER ***************************
owner HPS
content layer3
vip address 14.60.64.210
no persistent
add service tempest
primarySorryServer zephyr
active
!*************************** GROUP ***************************
group SOURCE-IP-NAT
vip address 14.218.74.112
active
!**************************** ACL ****************************
acl 10
clause 10 permit any any destination any
apply circuit-(VLAN10)
acl 20
clause 10 permit any any destination any
apply circuit-(VLAN1)
acl 30
clause 10 permit any any destination content HPS/layer3 sourcegroup SOURCE-IP-
NAT
clause 90 permit any any destination any
apply circuit-(VLAN2)
~~~~~~~~~~~~~~~~~~~~~~
Pretty simple, but when I go to configure VLAN10 as the interface to run VRRP on:
scc-lb1(config)# circuit VLAN10
scc-lb1(config-circuit[VLAN10])# redundancy-protocol
^
%% Invalid input detected at '^' marker.
scc-lb1(config-circuit[VLAN10])# re?
redundancy Configure this circuit for redundancy
restore Restore commands
*** Aliases ***
reboot_diags @configure;boot;rebo diags
reboot @configure;boot;rebo
scc-lb1(config-circuit[VLAN10])#
The "redundancy" command is the only command it will recognize.
Anybody have any clue what is happening here?
Thanks!

Hi,
In order to add "redundancy-protocol" to the circuit, you need to go into the ip address section after going into the circuit section and then it will be an available option.
Like this:
scc-lb1(config)# circuit VLAN10
once in the circuit section, type in the ip address of the circuit.
Then you will be in the ip address part of the config and type in "redundancy-protocol"
Regards
Pete Knoops
Cisco Systems

If for some reason u have the icon in your task bar (the one with 2 arrows pointing in a circle) just go into mobile me pref...click sync...and uncheck box show status in menu bar. My question is, I do not have this option. How do I get the sync to stop

"if for some reason u have the icon in your task bar (the one with 2 arrows pointing in a circle) just go into mobile me pref...click sync...and uncheck box show status in menu bar."
I do not have the option box to "show status in menu bar"
I tried the free for a little while Mobile me, and didn't use it, so cancled. I cannot get the sync status roundabout arrows out of my status bar. AND, they keep trying to sync.
Another issue related with this is that during the time that I tried out Mobile me, I had my ical alarm set to go off every 2 hours. NOW my computer has an ical pop-up every 2 hours. I cannot find how to stop it.
Another issue, Yahoo is trying to sync with my computer and I have no idea why or where that one came from.
Can anyone out there help me please.

"if for some reason u have the icon in your task bar (the one with 2 arrows pointing in a circle) just go into mobile me pref...click sync...and uncheck box show status in menu bar."
I do not have the option box to "show status in menu bar"
I tried the free for a little while Mobile me, and didn't use it, so cancled. I cannot get the sync status roundabout arrows out of my status bar. AND, they keep trying to sync.
Another issue related with this is that during the time that I tried out Mobile me, I had my ical alarm set to go off every 2 hours. NOW my computer has an ical pop-up every 2 hours. I cannot find how to stop it.
Another issue, Yahoo is trying to sync with my computer and I have no idea why or where that one came from.
Can anyone out there help me please.

How can I get a picture to go with my email signature when sending emails from my iPad? Only a square box shows up on my signature not the actual picture I iploaded in my settings.

How can I get a picture to go with my email signature when sending emails from my iPad? Only a square box shows up on my signature not the actual picture I iploaded in my settings.

Only Apple Account Security could help at this point. You can try calling Apple Support in Canada - you'll have to find one of the several ways, such as Skype, to call an 800 number from outside of the relevant country - and ask for Account Security and see if they can help. Or you can find a friend who speaks Chinese and ask them to help you talk to Apple Support in China. There are really no other options that I know of.
Note, by the way, that these are user-to-user support forums. You aren't speaking with Apple when you post here.
Regards.

My icloud emails arent arriving most of the time and a few days ago my iphone and ipad started showing "Can't Get Mail" box. This has not happened before since I set up the iclud email address with the purchase of my ipad about a month ago.

My icloud emails arent arriving most of the time and a few days ago my iphone and ipad started showing "Can't Get Mail" box. This has not happened before since I set up the iclud email address with the purchase of my ipad about a month ago.

That's one of the weird things.. it recognizes it maybe 10% of the time. And usually, only after I do the two-button reset. Problem is.. since it won't charge above 2%, anytime I try to do a restore or anything like that using iTunes, my device shuts off and I lose whatever progress I'd made.
So, an update... after reading through a bunch of similar complaints (there are literally 1000's of them so there's NO WAY this isn't somehow ios7 related, thanks a lot APPLE ) I decided to try a restore in recovery mode. After 3 hours and several disconnections... I ended up having to just set it up as a new iPad, as the restore did nothing. Weirdly though... as I was doing the restore in recovery mode.. I noticed I'd gotten up to a 10% charge.. higher than it's been since September, so after setting it up as a new device, I turned it off and plugged it in using the wall charger. 2 hours later and I was up to 38%. Still not great, as my iPad, before ios7 could've fully charged twice in the amount of time it took for me to now get 28% more of a charge. And that's with a fully cleaned out device.. so that really ***** and I'm now more confused than ever.
But I'm gonna leave it overnight charging and see what I come up with tomorrow. Sadly, when I paid $600 for it in February, I never expected to have to play "wait and see" with it...

Titles are not visible, they show up on timeline as a grey box no text does not effect other events or projects

titles are not visible, they show up on timeline as a grey box no text does not effect other events or projects. could this have something to do with motion

Without seeing the timeline it sounds as if they've been off. Maybe you pressed the V or the role is switched off in the timeline index.

JCA is not showing in protocol dropdown in Eclipse3.5.2 IDE

I'm creating OSB business service with *db.jca file, which is imported from JDeveloper. It is creating .biz and .wsdl files in the directory. Then I'm trying to modify the business service with JCA transport. The JCA protocol is not showing in protocol dropdown in eclipse IDE. I'm using Oracle SOA Suite 11gR1(11.1.1.3) and oepe_11gR1PS2. Do I need to install any plugin for it? if yes, where can I get it.

Please find below my eclipse.ini file after updating 32bit jvm. Highlighted are the changes made. Still I'm not able to see jca protocol in dropdown. I've observed, plugin folder of OEPE contains only "oracle.database.driver.jdk14_10.2.0.1", "oracle.database.driver.jdk50_11.1.0.7" folders. there is no folder for jdk6.
-vm
C:/Program Files (x86)/Java/jdk1.6.0_35/jre/bin/javaw.exe
-startup
plugins/org.eclipse.equinox.launcher_1.0.201.R35x_v20090715.jar
--launcher.library
plugins/org.eclipse.equinox.launcher.win32.win32.x86_1.0.200.v20090519
-showsplash
org.eclipse.platform
--launcher.XXMaxPermSize
256m
-vmargs
-Xms256m
-Xmx768m
-XX:MaxPermSize=256m
-Dweblogic.home=C:\Oracle\Middleware\home_11gR1\wlserver_10.3
-Dharvester.home=C:\Oracle\Middleware\home_11gR1\Oracle_OSB1\harvester
-Dosb.home=C:\Oracle\Middleware\home_11gR1\Oracle_OSB1
-Dosgi.bundlefile.limit=500
-Dosgi.nl=en_US
-Dsun.lang.ClassLoader.allowArraySyntax=true

Highlight boxes show in preview but not in published work - Captivate 5

Hello,
I'm hoping someone can help me with this as I'm utterly confused at the moment. I'm working on a software simulation and have been working alot with highlight boxes. I have done at least 3 modules (25-60 slides each) with highlighting and haven't had a problem until now. My problem is that I can't get the highlight boxes to show up on the published document. This is only for 1 single slide! All the rest work!! When I preview in the program the boxes show up and work perfectly but they don't show up in the published doc. I have duplicated slides and rerecorded that specific slide and nothing works. Any theories??
Please help!

Hi there
The image isn't crystal clear, but it would appear the top element is a Click Box configured to pause the slide at 1.5 seconds? Again it's difficult to see because it's not exactly clear, but it would also appear that your highlight boxes aren't configured to present until about 6 seconds in. So in this case it would seem the Click Box is pausing the slide too soon. Try adjusting the timing of the Click Box.
Cheers... Rick
Helpful and Handy Links
Begin learning Captivate 5 moments from now! $29.95
Captivate Wish Form/Bug Reporting Form
Adobe Certified Captivate Training
SorcererStone Blog
Captivate eBooks

ICM paper profile not showing up when I go to the print modual and select icm check the box show all

The icm profile that I installed shows up in the printer profile. I select it then enter the print button at the bottem select my printer open the propertied and when I select icm in the mode window advanced check the box show all profiles, The only profiles that show are the one that came with the printer not the one that I installed and did show back in the printer profile.
What am I doing wrong?

To see all profiles in Lr you have to click on the two small triangles besides the profile selected in the Print Job panel.
See Screen shot:
Then a list of profiles will appear. If you don't see the profile you are looking for in this list, click on <Other> at the bottom of the list. This will take you to the folder where al profiles are installed, and if your profile is in this folder you should see it there.
If you still don't see it then it's a CMYK profile. CMYK profiles show up in Photoshop but not in Lr.
BTW: If you want Lr to manage colors you have to select a profile where it says <Profile> in the Print Job panel and not by clicking on <Print>.

Failover to redundant box shows Redundancy Protocol: Not Running on CSS

Similar Messages

Maybe you are looking for