Failure while compacting the virtual disk on the backup location

Hi!
I have a following error while doing scheduled backups: "Failure while compacting the virtual disk on the backup location"
OS is Server 2012 R2 Essential
I use a dedicated HDD for backups. Its a WD GREEN 3TB.
Any suggestions?
LOGS:
EROOR: The backup operation that started at '‎2014‎-‎06‎-‎27T00:57:25.744931200Z' has failed with following error code '0x807800C5' (There was a failure in preparing the backup image of one of the volumes in the backup set.). Please review the event details
for a solution, and then rerun the backup operation once the issue is resolved.
WARNING: The backup operation that started at '‎2014‎-‎06‎-‎26T16:30:31.944377600Z' has completed with errors. Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.

Hi,
Try to back up to local drive to check if the issue still exists? The issue could be the backup set was corrupted. You could refer to the thread below to troubleshoot the issue:
Server 2012 backup fails while preparing one of the local volumes with "the mounted backup volume is inaccessible"
http://social.technet.microsoft.com/Forums/windowsserver/en-US/20ab10a8-fb39-451f-9076-46a6188b2139/server-2012-backup-fails-while-preparing-one-of-the-local-volumes-with-the-mounted-backup-volume-is?forum=windowsbackup
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Similar Messages

After a power failure while iPhoto was running, I get the message "Your photo library is either in use by another application or has become unreadable" and iPhoto will not open????

After a power failure while iPhoto was running, I get the message "Your photo library is either in use by another application or has become unreadable" and iPhoto will not open???? held down the option and the command and tried to run what was ticked off and it just sits there with a spinning wheel and does nothing, can I throw the app away and download a new one? or will it still not open?

, can I throw the app away and download a new one? or will it still not open?
You could, but the error message is indicating that your iPhoto library needs repairing.
Check, if iPhoto will run, if you launch it on a new library. Hold down the alt/option key, while you launch iPhoto. Select to create a new library from the panel that will show. Can you create a new library? If yes, try again to fix the library. Which options have you tried from the Library First Aid panel, when you launched iPhoto with the option and command key held down?
If you have not tried "Rebuild"; do that next. But be sure to make a backup of your iPhoto library, before you try this.

"A critical error has occurred while running the virtual machine and the machine execution has been stopped"

I have the following error:
"A critical error has occurred while running the virtual machine and the machine execution has been stopped"
When I am installing grid clusterware and when is copying files from one node to other I received that virtualbox error and is stop working.
Can somebody give me any hint how to solve it ?
Thank you
Eugen

I think that is not a Clusterware issue, The clusterware installation may generating a high load on your machine and Virtual Box is not supporting.
Check vbox.log file to identify root cause.

Ello, I changed my Imac hard drive which no longer worked. I installed a hard drive Western Digital 500 GB 7200 rpm SATA3 WD5002AALX 32M Black. Sometimes I see the hard disk in the utility on the Starter CD, but access seems very slow. By cons when I want

Hello, I changed my Imac hard drive which no longer worked. I installed a hard drive
Western Digital 500 GB 7200 rpm SATA3 WD5002AALX 32M Black. Sometimes I see the hard disk in the utility on the Starter CD, but access seems very slow. By cons when I want
install OS X 10.4.2 on the hard drive, I do not see the disk. What is the problem?

Thanks for the help
I started on the installation CD OS X 10.4.2, I used Disk Utility
to partition the disk according to the document that you have proposed. unfortunately
I have not succeeded. When I partition the disk, even if I called it Macintosh HD, it
does not keep the name and it shows disk0s3 instead. I did an erase on disk.
When I mount the disk it tells me that I must repair. When I tried to repair, I got
the following message:
Volume check failed
The underflying task reported failure on exit
1 HFS volume checked
1 volume could not be repaired because of an error.
I also had a message:
Invalid b-tree node size.
Note: The disc is new, but it has already been formatted on a computer Imac 27 inch 2011 OS X Lion.
I used a USB 2.0 to SATA cable to adjust the formatting.
What to do to fix it?

Had to buy a new PC as the hard disk of the old one broke and lost all purchases, but still have them on the iPhone. How can I sync them back to the new PC in iTunes?

Had to buy a new PC as the hard disk of the old one broke and lost all purchases, but still have them on the iPhone. How can I sync them back to the new PC in iTunes without losing them?

You should be able to:
Backup the device to the new installation
Transfer your purchases into a newly authorized library
Recover any other media using third party tools as suggested in this post from forum regular Zevoneer
Restore the device from the backup
This process should switch the association of the device to the new library, preserving the data and settings in your apps.
May also be prudent to attempt a backup to iCloud directly from the device before you start... Settings > iCloud > Storage & Backup > iCloud Backup > On. It won't save any media but it would preserve the general account settings and documents in case anything goes wrong while you are trying to extract your other data.
When you get it all fixed, make a backup!
tt2

I am trying to boot Ubuntu 12.4 on my iBook G4, but am having trouble getting my iBook to recognize the boot disk in the CD Drive. Why?

I am trying to boot Ubuntu 12.4 on my iBook G4, but am having trouble getting my iBook to recognize the boot disk in the CD Drive.
I have pressed "C" during boot to force it to boot from the Optical Drive. It boots normally.
I have pressed "option" to get the boot menu. The only option available is my hard disk drive.
I have pressed "option""command""shift""delete" at the same time during boot to force it to skip booting the hard disk. I get a blinking smily face/question mark for a while, then it shows the boot menu, at which point the only available option is my hard disk drive.
In system preferences in OS X I have looked to change the boot drive, but the only option, again, is the hard disk.
Can I not boot from the Optical Drive?
Why?

Hello,
From the link I provided it says:
Nearly all open-source software is available to download from the Ubuntu repositories, but the amount of proprietary software available for PowerPC linux is limited. You will have the same version of Firefox, LibreOffice, etc as other architectures.
Notable absentees are: Chrome/Chromium, Adobe Flash (although open-source alternatives are available, see below), Wine (however Qemu can be used, see below), ndiswrapper, proprietary video drivers and Dropbox (but, you can use Ubuntu One).
I do recall it being very limited when it came do downloading Linux software that supported PPC.
You wouldn't be any better off than using firefox or safari on Mac OS X 10.4.11.
If your looking for a faster and more compatible web browser then I would suggest the following, which I've recently found very useful on Mac OS X 10.4
http://www.floodgap.com/software/tenfourfox/
Hope this helps.

Migration Assistant doesn't see the startup disk from the old G4

Hi,
I just got my new iMac and was about to transfer stuff from my old G4 which have two internal disks. But I stumbled into serius problems right away. Migration Assistant is not able to see the startup disk from the G4. It sees only the other disk.
I have tried to disconnect the extra disk and checked that the startup disk is forced with the jumper to be the master disk. With this configuration it won't start the G4 at all. Having he jumper in the cable select slot results to shut-up with the T-button (firewire) startup and normal startup without the T-way.
What should I do? I can't figure out what the problem is.
I enclose some System Profiler data of the problematic disk if this helps to find the solution.
Model: MAXTOR 6L060J3
BSD Name: disk0
Protocol: ATA
Unit Number: 1
OS9 Drivers: Yes
S.M.A.R.T. status: Verified
File System: Journaled HFS+
BSD NAme: disk0s10

Ok. This is really simple to do.
The idea of the dual drive iMac is that the System and Apps reside on the fast SSD and that the user directories reside on the HD.
You first need to create the same accounts on your SSD as on your old iMac.
The next step is to change the path of the user accounts from the SSD to the internal HD. Duplicate or copy the Users directories on the SSD to the HD.
Change the path in System Preferences > User & Groups > Unlock to make changes > Select User account in sidebar > Right-click > Choose Advanced Options > Home Directory > Choose the Volumes/your_hd/Users/user_name.
Restart your iMac and restore from Migration Assistant.
Remember to keep the empty directories on the SSD, in case you ever have a HD failure or replacement, you will have to change the path back to the SSD.

I want to upgrade my 2007 Mac desktop to 10.5 Leopard. I am currently running on 10.4.11. I have put the leopard disk into the drive and all it does is make a weird noise and then spits the disk right back out. It doesn't do this with other disks. HELP

I want to upgrade my 2007 Mac desktop to 10.5 Leopard. I am currently running on 10.4.11. When I put the leopard disk into the drive all it does is make a weird noise and then spits the disk right back out. It doesn't do this with any other discs, only this software. Is it still possible to update this computer?

Yes. Try Amazon.
Before you do upgrade to Snow Leopard, make sure your Mac meets the requirements.
Mac OS X v10.6 Snow Leopard - Technical Specifications
Make sure the disc you tried using doesn't have any fingerprints or smudges on it. The optical drive can't read the disk otherwise.
If your Mac won't read the disc, might be a good idea to rule out any problems with the startup disk BEFORE trying to upgrade the system.
Using Disk Utility to verify or repair disks
Message was edited by: Carolyn

I have replaced my ibook hard drive but when I start up I get a folder with a flashing question mark. I have tried installing the OSX disk using the "C" key but can't get any further than the flashing "?." What do I do? What is the problem?

I have replaced my ibook hard drive but when I start up I get a folder with a flashing question mark. I have tried installing the OSX disk using the "C" key but can't get any further than the flashing "?." What do I do? What is the problem?

Which iBook do you have?
http://support.apple.com/kb/HT1772?viewlocale=en_US
Which version of the OS is installed, and which version are you trying to install?
You could try starting up with Startup Manager and see if it will allow you to select the OS X install disc as the startup disk. If so, maybe you can proceed from there. I would recommend repairing the hard drive first since you are evidently having a bit of a problem with it.

I converted from a PC to a Mac Mini. I have my PC documents backed up on a DVD disk. I have an external DVD drive connected to the Mac Mini. I want to open them up and save them to the Mac, BUT....when I put the DVD disk in the Mac is NOT reading it!

I converted from a PC to a Mac Mini. I have my PC documents backed up on a DVD disk. I have an external DVD drive connected to the Mac Mini. I want to open these documents up from the DVD storage and save them to the Mac, BUT....when I put the DVD disk in the Mac is NOT reading it!

Hi Joe,
Thanks for your quick response. I should add....it worked before. When I previously inserted the two DVDs into this remote drive, and I went into finder, I could click on the "remote device" line and see all my saved documents (excel, word, etc) on the DVD and open them on the Mac. Now I cannot see them, when I try to open them on the Mac, nothing happens, nothing is displayed. I just re-tested the remote DVD drive with a CD and, no problem, it opened up the CD via iTunes and I cold play the CD. SO......I know the remote DVD drive (it's an LG by the way) is fine, it's something to do with some settings on my mini mac,especially where I could open it previously. I do not remember changing any settings since then.
When I go into system preferences and click on CD/DVD it gives me options of how to open up a music CD (default is iTunes), a DVD (default is iMovie), etc. The problem is my DVD is all miscellaneious files/documents. I just want to be able to see them in the finder. I also tried to open them via microsoft word, from the remote disk and again, it could not open the drive, even though some of the documents were microsoft word documents. Again, I was able to open them previously and the DVD is not corrupted in any way.
Any additional advice?
Thank you!

How to upgrade the hard disk of the nomad jukebox

I read the FAQ of nomad on nomadness.net, I wanna know how to upgrade the hard disk of old nomad jukebox with a bigger one?
I also read a artical on tom's hardware about this,
http://www7.tomshardware.com/mobile/20000/mp3-3.html
but he gave a link
http://www.kuren.org/jukebox
that is not available. He mentioned that it need to clone the fist 65536 sectors from the old disk to the new one, but I have not the old hard disk( I bought a second hand nomad jukebox without the original hard disk). How should I do?
Does someone have the image file of the fist 65536 sectors from the old disk?
Thank you!

That was the old method before Creative published their Bootcode Flasher software.
Follow the instructions here:
http://www.nomadness.net/modules.php...ticle&artid=24
All files mentioned are available somewhere on Nomadness. Also check out the sticky thread in their JB section of the forum as it lists what hard dri'ves will work in a JB and which ones won't. I hope you haven't already bought your upgrade hard dri've.
I used the above method without any problems and now have a 20GB JB.
PB

How to get the absolute path of a file from the local disk given the file n

how to get the absolute path of a file from the local disk given the file name

// will look for the file at the current working directory
// this is wherever you start the Java application (cound be C: and your
// application is located in C:/myapp, but the working dir is C:/
File file = new File("README.txt");
if (file != null && file.exists())
String absolutePath = file.getAbsolutePath();

I disabled my Macbook Hard Disk and lock the settings, after i try to reboot, the system wouldn't come up. It refuses to read instructions from the hard disk. How can i enable the hard disk when the system wouldn't come up?

I disabled my Macbook Hard Disk and lock the settings, after i try to reboot, the system wouldn't come up. It refuses to read instructions from the hard disk. How can i enable the hard disk when the system wouldn't come up?

How do you disabled it if running the same?

�Unable to create the virtual machine. The error was -4�

I have a VS2003 C# application, which call JACE (a JNI wrapper) through C++ mixed mode to use JAVA object�s functions.
Because the natural of our JAVA program it must be able to reach maximum heap size of 512MB, we set it during the startup of JVM by using �-Xmx512M� parameter.
It worked well with a small PC (Dell Optiplex GX750 and Shuttle Xpc ) with only 512MB physical memory. We have about 50 machines running the application in the production.
Recently, one of our customers installs the application to a larger PC ( Shuttle Xpc with different model), which has 1 GB of physical memory. The application started throw exception from JVM. The error message is �Unable to create the virtual machine. The error was -4�. I checked with JNI return code and found that -4 mean �not enough memory�.
I did some experiment by running the application with 2GB PC, 1 GB PC, 1GB laptop, 512MB PC. I don�t found relationship between how much �maximum heap size� can be assigned and how much �physical memory� is available (reading from task manager). The 2GB machine can take only 128MB of �maximum heap size� However, 1GB machine can take up to 300MB of �maximum heap size�.
I also use program like ImageJ (http://rsb.info.nih.gov/ij/) to test maximum heap size for it. I found that ImageJ can take 512MB maximum heap size without problem. It can even take 1024MB of maximum heap size.
I have created a small program to duplicate this problem. Although it use exact the same code to start JVM up, it can go up to 650MB heap size for both 2GB and 1GB PC.
This is puzzling. Does anyone know what are factors determine how much �maximum heap size� can be set for JVM from JNI?
Software used
Windows XP SP2
Visual studio.net 2003 SP1 (the problem also occurred without SP1)
.NET Framework 1.1 SP1
JACE 1.1rc1_05
JRE 1.5.07 (also tested with JRE 1.5.09 and 1.6.0 beta)

Do you resolve the problem? If so what was the fix?
I have been getting the Java Virtual Machine Launcher error message Could not create the virtual machine when attempting to run an Oracle application that uses JNLP via a browser. Even clicking on componets such as javaw.exe produces the error message. In conjunction with receiving the error message, the application that I am working with will not launch.
I had JRE 5u10 and J2RE 1.4.2u13 installed and thought that installing JDK 5u17 may resolve the issue. I removed JRE 5u10 and J2RE 1.4.2u13 and installed JDK 5u17 (and the included JRE 5u17.) The error message was still there.
I have unistalled (via Add/Remove programs) and reinstalled (via both Win off-line and on-line) JDK 5u17 and JRE 5u17 many times.
During the uninstalls I have received a Java Web Start 1.5.0_17 bad installation error invoking JVM error message.
I have restarted the machine also.
There are some remains of J2RE 1.4.2u13 still on the machine even after the 1.4.2u13 uninstall. The Java\j2re1.4.2_13\lib folder remains.
I am running Win XP SP2 and IE6 SP2.
Note: I cannot use Java 6 since the application that I am working with is Java 5 based.

How to replace the virtual system as the real system in the TMS?

Hi,
I have a standard 3 systems TMS, which is 1 development system (real system, transport domain) and 2 virtual system(QAS and PRD).
And now, I will install the QAS system and replace the virtual system as the real one, How can I do in TMS?
I should delete the old TMS and rebuild the TMS with 1 DEV, 1 QAS and 1 virtual PRD? or just replace the QAS as the real one? What the operation should I do in t-code:STMS?
Many thanks.
BR,
Randy

Hi,
Do it as follows.
1. Remove transport routes (i think it is not mandatory)
2. Remove your Virtual system that you want to replace with physical system
3. Include the Physical system into Domain and accept it from Domain Controller
4. Configure the transport routes.You can see all the transports that were in the import queue of virtual system are now in the import queue of the Physical system that you added.
Only condition is, both Virtual System and Physical System should have same SID.
All the above will be done through STMS
Thanks,
Giri

Failure while compacting the virtual disk on the backup location

Similar Messages

Maybe you are looking for