"Fan error" on Thinkpad X201s

Hello,
My X201s surprisingly overheated and soft-shut down. Upon rebooting the BIOS interrupted startup just to say "Fan Error" and shut down again. Has anyone seen this issue before? Up until now the fan has been working!
I took the keyboard off, and as soon as I press the power button, I see the fan spin for a few seconds then stop - it does not start again and says fan error. I have blown all the dust out, and the fan turns very freely - is there anything else I should try before I send the laptop to be repaired (it is still in warranty but it is a bit of a bore!)?
Thanks for any help,
Edward
Solved!
Go to Solution.

Either the fan is running a little slow or the temperature sensor circuitry is sick. Send it in. It is a pain, but it is the best choice.

Similar Messages

  • How to bypass fan error on Thinkpad x220. Thank you.

    I am in a urgent need to access my data for work. I tried to press esc but it does not work, both holding down, press frequently, etc.
    Does anyone can share how to boot the windows regardless the fan does not functioning.
    Thank you in advance
    Thana
    Solved!
    Go to Solution.

    In case anyone else try to find the solution too. I didn't come across one. I changed the fan got from ebay and it is up and running. 

  • Fan Error on X201

    I bought my X201 (3249CTO) last october from lenovo's website. 2 weeks ago, my laptop became unable to boot up except showing "Fan Error" message. Before that, my laptop sometimes suddenly shut down(directly to dark screen) with no reason. 
    The Warranty is going to expire tonight. I still can not find the entry to report this error and ask for repair on this lenovo's official website. Most links I've seen are "check....", "check...", or "extend or upgrade"... and some software solutions. I can not find any tech support email. When I go to the "CONTACT" page, most contact info is about sale, business. After I click, click and click, I found that "800-xxxxxxx" tech support number. Following the instructions, I press 1, 1, 1... and hearing a lot of electric voice"please go to www.lenovo.com.....", I heard that their manual service was only available during 8a - 8p Mon - Fri. While I'm most on class during that time. Why don't they have an email for warranty service?
    How can I contact them to return my laptop back and get repaired?

    @LilHayah,
    You would need to call the tech support via the number 800-xxxxxx then they would advice you on how to get the laptop shipped back for service or if you have a onsite service.
    There are no emails for tech support.
    //JameZ
    Check out the Community Knowledge Base for hints and tips.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
    X240 | 8GB RAM | 512GB Samsung SSD

  • Fan error on IBM thinkpad X60s notebook

           When I switch on IBM thinkpad X60s notebook. I can hear a sound from fan like it is try to move and then stop. After awhile an error "fan error" appear on the screen. I would like to know is it related to fan problem? If yes, Do I need to change a new fan? Actually, this notebook is out of warranty. So what will it cost for fan assembly and the labour charge? I live in Johor Bahru, Malaysia. I would like to know is there any service center in Johor Bahru? Thanks for reading and reply to my post.

    Apa kabar?
    Sounds like you will need another fan installed. If you unit is still under warranty, call your local tech support to assist. I'm not sure about your exact location in Malaysia, but I know that there are some locations in KL.
    I was able to find this tech support number in Malaysia for you.
    1800-88-1889 (Local number only)
    +603 8315 6855 (DID)
    Monday - Friday 8:30AM - 5PM
    Give them a call for assistance. Best of luck.
    Mark
     Do NOT PM me with technical issues. Post in the forum for assistance. Thanks

  • Fan error at startup in ibm thinkpad t42

    i always get fan error at startup in my  ibm thinkpad t42 since 1 week. i press esc key at error and that is the only way my system startup. its not in warranty and will like to try to fix it on my own. please help. i am worried

    Try bblowing some air into the fan lover when the system is off. Then turn the system on and put your hand at the louver to see if it blows air. If this doesnt work, run PC doctor for DOS ( available at  http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-56222) and check the problem. If this doesnt work either, replace the fan.

  • Trying To Create Bootable Diagnostics for ThinkPad X201

    I'm working on a ThinkPad X201 that spontaneously shuts down - no warning messages, no blue screens; the system just shuts off. Not only does it happen while using Windows (that's Windows 7 Pro, 32-bit), but it also did it while I was running memtest86, a generic memory diagnostic.
    I've also tried SpeedFan to see if the computer is experiencing thermal shutdown, but SpeedFan has yet to register a temperature in excess of 50C, well below the thermal shutdown threshhold on most computers.
    That said, SpeedFan isn't the be-all and end-all of thermal diagnostic tools, and irrespective of what it says, the computer did seem to be blowing very hot air the second time I ram memtest86. Before I go to the trouble (and my customer's expense) of taking the computer apart, making sure the fan and cooling channels are clear and replacing the thermal compound on the processor and other chips that the heat sink sits on top of, I'd like to run Lenovo's bootable diagnostics.
    I loaned out my external optical drive, so for the sake of expedience, I've been trying to make a bootable diagnostic flash drive. Lenovo provides a utility for this, but I can't get it to work. Per the instructions, I downloaded the ISO file and the bootable flash drive utility to a folder, and named them diag-image.iso and bootable-generator-10.exe, respectively. I put a USB flash drive (a 32GB SanDisk Cruzer, USB 2.0 version) in a USB port, and Windows assigns it drive letter E:. From an elevated command prompt, I change to that folder, and run the command:
    bootable-generator-10.exe --create -l lenodiags -u e -f diag-image.iso
    All I get back is the following error message:
    Validate bootable
    Failed to verify flags.
    The bootable in E:\ is not valid.
    Can anyone assist with this?
    Mark Lebowitz, Owner
    Lebowitz IT Services LLC
    Chicago, IL
    Lebowitz IT Services LLC
    Chicago, IL

    The method for creating a Mountain Lion flash drive only required you to clone the installer disk within the application to the flash drive. Job over. No need for passwords. With Mavericks Apple provided a way to do it because the old method used with Lion and Mountain Lion doesn't work for the Mavericks installer.
    Would have been nicer had they provided an easy application to do it, but they did not. So it requires the Terminal, they more or less hid the fact it was even there, and they provide no instructions for its use by less experienced users.

  • Fan Error on x220

    Hi everyone,
    I have a (now) 2 year old Thinkpad X220 with Intel i7 processor (CTO 4286) with no warranty (only got the 1 year limited warranty, as I assumed this was a premium laptop).
    Sadly enough a month ago the fan stopped working, and I get a "fan error" message on boot-up. This as, in effect, turned my +1200 dollar laopt quite useless.
    What I have tried to fix it so far is the following (in this order)
    1. Blown out dust from the fan area
    2. vacuum cleaned fan area
    3. Dissambled unit, vacuum cleaned fan unit
    4. Applied small bit of oil to fan unit mechanism
    5. Reapplied thermal paste to cooling unit
    6. REPLACED fan unit and thermal paste
    However, the message is still there and my laptop (which cost me an arm and a leg, as I was planning to use this laptop for 5 years - just like my x41 before it) .. is still dead.
    Does anyone else had this problem (especially those that did not have the warranty anymore), and does anyone else has any other suggestion? Would much appreciate it, as I need this laptop and cannot afford a new one..

    "fan error" does not mean "too hot"; it means "running too slow". You probably need need a new fan. (The only other things involved are the fan sensor and a fuse (both part of the motherboard). They are unlikely causes and expensive to fix.

  • Fan error t410s

    Anybody have experience with fan error? It made very loud noise while I was using my computer and after that I turn my computer off and cannot turn it on. It shows fan error. Very disappointed with my first thinkpad. I got it a year ago. Just passed warranty less than a month. Touch pad and battery life also are not good.

    Take off the keyboard and see if the fan can spin freely.
    http://www-307.ibm.com/pc/support/site.wss/MIGR-72739.html
    You need to turn off Gesture Filtering and Edge Tap Filtering for the touchpad and maybe turn the touch sensitivity up. Average battery life on the T410s should be around 2 to 2.5 hours it seems.
    W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
    X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
    Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

  • Fan error message on T60

    I just received a funny noise and fan error message when I boot up my T60. I think I need replace the fan for my laptop. Can anyone tell me the part number and how to replace it. Thank you

    Hello robertnguyen, welcome to Lenovo forums!
    Please tell us your model number, not S/N.
    That will help us to help you.
    Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
    Please insert your type, model (not S/N) number and used OS in your posts.
    I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
    TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
     English Community       Deutsche Community       Comunidad en Español

  • Fan Error message on T43 after replacing it.

    I have a T43 (2687-DVU) that received a Fan Error at boot up.  I replaced it with a new fan (am sure it is correct fru) and the fan is working fine.  The temperatures are also fine on the unit (I can hear the fan, feel it blow out heat - bottom line the fan is working).  I have reseated the unit a few times - made sure thermal paste is correct - connector to motherboard is connected (otherwise the fan will not work).  I can ESC to bypass the error and run what appears normally.  I don't think I have a fan error, except in the mind of a deranged motherboard, perhaps.  I have 2 pronged question to throw out.
    Would eveyone agree that this probably a motherboard problem or a fuse on the motherboard problem?
    Secondly, since the unit is out of warranty, would you bother to replace the motherboard,or would you just hit the escape key and live with it. ( I know this is just an opinion in most regards, but just wondering if it's worth fixing just to avoid a keystroke at boot time). 
    Thanks

    I'd be guessing something along the lines of a thermal sensor gone haywire.
    If the machine were mine, I'd run it until it dies and then swap the planar if the rest of the laptop is still in good shape. But it's your ThinkPad.
    My $0.02 only...
    Good luck.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • How to bypass Fan Error on X1 Carbon

    Hi folks,
    We're in a real pickle right now trying to help out one of our faculty members.  She needs to use her new X1 Carbon laptop but is getting a 'Fan Error' message on her X1 Carbon immediately after turning it on. 
    Is there anyway we can bypass this error on the X1 Carbon?  We're trying the Escape key with no success.  We understand that the laptop may need a fan replaced, but we really need to access data for an important conference tomorrow in Dubai.
    Any ideas or suggestions?  Thank you kindly!!

    http://forums.lenovo.com/t5/X-Series-ThinkPad-Laptops/X1-Carbon-Won-t-Boot-without-AC-Cord-reset-swi...
    try this method.
    Otherwise you would be in a pickle. This is one reason why i dislike Ultrabook format with their proprietary SSD format.
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • T61-Fan Error on startup and cant boot in system

    after Thinkpad logo, 2 short 'Bee' sound and 'fan error' message appears on the top left screen, then 1 'Bee' sound, laptop shut down. Althought can boot in system by pressing Esc when 'fan error' appears, but dont know this will damage something like circus or chips.
    Anyone have same problem and solved it? Should I change the fan, and which fan (video car fan or cpu fan) is this problem about. I have a limited warranty dont know if the fan is included.
    Thanks

    Fan is covered by warranty, when fan stops spinning then it would usually cause this error.
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • T410s Fan Error on Boot but works sometime...really confused

    Hi, I bought the t410s back in 2010 april or march. About 7-8 month later, I started getting Fan Error on boot after the thinkpad screen. If I don't do anything, the computer shuts off automatically, but if I hit escape, it would continue boot and start up (without a working fan).  I know that there are other threads about the fan error but none of them mentioned this. Most of the times after it continue booting after escape on fan error, I would do a cold reboot and the Fan Error would be gone. So Im guessing that the hardware is fine because if they faulty, then it shouldn't work at all. So recently, I did a clean install of windows 7 and updated all drivers and bios. After update, it was working for like 4 days so I thought it was just a software issue but now the problem have returned, same as before. Sometimes it boot with fan error, sometime no error. And after shows fan error, if I escape and reboot, most of the time the error would be gone. Anyone know why this is or what is going on here? Anything would be appreciated, thanks.

    hey dy58,
    since it is hard to replicate this issue as sometimes it does happen and sometimes it does not, i do recommend bringing the unit to an authorize service center for them to investigate.
    do contact the tech support team for information of the nearest service center
    http://support.lenovo.com
    WW Social Media
    Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
    Follow @LenovoForums on Twitter!
    Have you checked out the Community Knowledgebase yet?!
    How to send a private message? --> Check out this article.

  • Could not get Crucial M500 SSD to work in Thinkpad X201

    I have a ThinkPad X201 running Window 7, I have not make any changes to the computer hence all the hardware are original.Except when I recently bought a Crucial M500 SSD, First I use MiniTool to clone the HD to the new SSD. After cloning, I install the SSD into the X201. Window appear to boot up normally with no error message. But soon I notice the Window is not working correctly. For example Window no longer recognize Microsoft published program. For a simple thing like pressing Del to delete a file. A UAC warning will come on to asked if I will allow delete,exe from an unknown publisher to make changes to the computer.Then I tried to repair window by downloading the Window 7 ISO file from microsoft site and proceed to do an upgrade of Window, The upgrading process took quite a while. When everything appear to have finished an error message came on to say "Window setup could not configure windows to run on this computer's hardware". So I gave up on cloning and try to make a clean install of Wondow on the SSD by using the Recovery DVD that came with the computer. The installation process gone through but at the end it ask me to put in the supplementary disk which did not come with the computer. Hence I could not complete the process. I am at a total loss, what can I do next to get it to work?   
    Solved!
    Go to Solution.

    serangoon55 wrote:
    thanks. I used Minitool to make the cloning which can be booted up from a CD/DVD. I will try to clone with the target in the laptop as suggested and let you know the result.
    Crucial normally supplies Apricorn EZ Gig software with their drives. If you don't have it, check Crucial's website and there should be a download available. It should work when it detects a Crucial drive connected.
    I didn't understand that you said you were going to order an external enclosure. How did you do your clone with Minitool? If you were using an adapter cable, you should also be able to use it to connect the HDD externally.
    The cloning software should take care of everything for you. The cloned disk should be a seamless, plug-and-play version of the original. You should not have to fix anything afterwards. Just boot it and start using it directly.

  • L530 Booted nicht mehr (Fan Error)

    Hallo zusammen,Seit gestern will mein L530 nicht mehr Booten. Wenn ich den Powerknopf drücke erscheint kurz der Lenovo Bootscreen und danach folgende Fehlermeldung: "Fan error. Thermal sensing error." 2-3 Sekunden später schaltet sich das Gerät aus. Der Lüfter dreht Läuft beim Einschalten an wie sonst auch immer. Ins Bios kommt man auch nicht. Jemand eine Idee ob/wie der Fehler zu beheben ist?

    Hallo atzenkoenig,
    Danke für die Infos.  Auf Deiner Stelle wurde ich jetzt folgendes probieren;
    Akku und Festplatte ausbauen und sicher zur Seite legen und der Stromkabel abklemmen.  Einschalt Knopf drucken und für ca. 5 Sekunden gedruckt halten - 10x wiederholen.
    Arbeitsspeicher (Memory) ausbauen und wieder einbauen um sicher das es richtig gesteckt ist.  (Hast Du eins oder zwei Speicherriegeln im Gerät?)  Nur der Stromkabel anschliessen, ohne Akku und Festplatte, und das Gerät einschalten. Bei die Meldung "To interrupt normal Startup......." bitte F1 drucken und nochmals in BIOS die Default Settings laden und neustarten.
    Gibt es jetzt Fehlermeldungen bitte?
    Danach darfst Du natürlich die Festplatte und Akku wieder einbauen bei getrennten Stromkabel.
    Um wie die Festplatte und Arbeitsspeicher ausgebaut werden, bitte die Videos auf die L530 Supportseite anschauen;
    http://support.lenovo.com/de/de/products/laptops-and-netbooks/thinkpad-l-series-laptops/thinkpad-l53...
    Andy  
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество

Maybe you are looking for

  • STO does not trigger forecast consumption unless re-releasing forecasts

    Hi, We need Scheduled Agreements, Customer Orders and STOs to consume forecast. While the first two work fine, the last one (STO) shows strange behavior. When an STO is created in R/3 and CIF-ed to APO, it does not consume forecast until we release f

  • 1440x900 Display

    Has anyone ever been able to get a resolution of 1440x900 working on a mac? I have a G5 and (2) Samsung monitors that really want to see a resolution 1440x900, and the video card says it will support it (NVidia FX6), but it is not listed in the avail

  • Jdev - 11.1.1.3.0 Unable to run application

    Hi All, I am unable to run the application developed in adf BC. I am getting below error when i try to run the page ( Error while compiling) package com.bea.plateng.common.util.diskspace does not exist Do let me know if i have to include any jar or m

  • What is the equivalent to wwv_corners in portal 10g?

    Hi, I'm migrating some pl/sql applications from portal 8i to 10 g, and I've found that the wwv_corners is gone in 10g. what happened? how come I cannot find anything on the documentation about this inner hidden database objects? Does anyone know wher

  • Is my iphone locked or unlocked?

    Hi just wanted to ask if my iphone that I bought from istyle in dubai is locked? I tried to insert a sim here in Florida but I think it's not working. What should I do? I've been trying to locate also here in florida if where could I unlock the phone