Fan not working on AMD card pwmconfig

I can run 'sensors' and the output is this (i cant feel any air coming thru my vga exhale)
atk0110-acpi-0
Adapter: ACPI interface
Vcore Voltage: +1.33 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: +3.34 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.08 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +11.88 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 3813 RPM (min = 600 RPM, max = 7200 RPM)
CHASSIS FAN Speed: 1800 RPM (min = 600 RPM, max = 7200 RPM)
POWER FAN Speed: 0 RPM (min = 600 RPM, max = 7200 RPM)
CPU Temperature: +44.0 C (high = +60.0 C, crit = +95.0 C)
MB Temperature: +30.0 C (high = +45.0 C, crit = +75.0 C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +46.0 C (high = +70.0 C)
(crit = +99.5 C, hyst = +97.5 C)
But the problem is, that I cant configure fan speeds, at all. Its overheating a lot because of it.
If I run as the wiki says, pwmconfig, I get
# pwmconfig revision 6166 (2013-05-01)
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
/usr/bin/pwmconfig: There are no pwm-capable sensor modules installed
I dont know what to do, I saw something about editing grub (and I tried it, and didnt work, also saw that is quite dangereous to do) but I find it odd that Its not detecting my AMD 6950 card. I also ran sensors-detect ,and they loaded 2 modules :
Just press ENTER to continue:
Driver `k10temp' (autoloaded):
* Chip `AMD Family 10h thermal sensors' (confidence: 9)
Driver `it87':
* ISA bus, address 0x290
Chip `ITE IT8721F/IT8758E Super IO Sensors' (confidence: 9)
Do you want to generate /etc/conf.d/lm_sensors? (YES/no): YES
ln -s '/usr/lib/systemd/system/lm_sensors.service' '/etc/systemd/system/multi-user.target.wants/lm_sensors.service'
Unloading cpuid... OK
Im using propietary drivers, which they have a far better performance in my opinion.
Thanks

Find a can of compressed air or an air compressor and a paperclip. Bend out the paperclip and stick it in the fan grille to hold the fan from spinning wildly and possibly getting damaged. Blow in the compressed air and see if there is a blockage that can be blown out. It works every now and then. Otherwise the computer needs serious service.

Similar Messages

Cooling fan not work correctly

my computer says the cooling fan not work correctly plase visit www.hp.com.go/teachcenter/startup

Dear Customer,
Welcome to HP Support Forum and we are glad to assist you
It looks like you are having difficulties with regards to the Cooling Fan of your Netbook
We will surely assist you with this
According to the message you have posted I suspect this is purely a hardware issue where in your getting "System Fan(90B) - The system has detected that a cooling fan is not operating correctly" message. This is a mechanical fault and the Cooling Fan on your Notebook and needs to be replaced before the Notebook starts up with an Overheating Issue.
Causes/Reason for this Issue:
1. Sometimes this is just because of Dust, Pet Animals Hair slowing down the fan
Perform the below shown troubleshooting steps:
Step 01. Turn OFF the Notebook
Step 02. Un-plug the Power/AC Adapter and also remove the Battery too
Step 03. Press and Hold the Power Button of the Notebook for a full minute
Step 04. Now let's re-insert the battery back in and plug back the Power/AC Adapter
Step 05. Start the Notebook and keep tapping F10 Key during the startup to access the BIOS
Step 06. Once you get to the BIOS, Please press F5 Key to load setup defaults for the BIOS
Step 07. Now let's press Esc/Escape Key. Save Changes and Exit - Yes
Step 08. Now please wait till Unit loads Windows and then Shut down the Netbook again
Step 09. You should clean all the Vents and Openings really good with a can of compressed air
Note: If you are still getting the same error we need to replace the fan
I strongly recommend you to immediately Contact HP Technical Support over the Phone for further assistance without any delay to get your Netbook Fan replaced and serviced by an authorized HP Certified Engineer
You can also Check your warranty Here to verify the warranty status
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

Mainboard is not working with any cards except mine(GeForce2 MX400)!

Dear friends!
I have sent a message but noone understood!
My problem is simple.
My mainboard is i845 MSI 6528LE!
My graphic card is INCA MX 400 Ge force2!
My mainboard is working good with this graphic card.But it is not working with other cards!For instance Winfast MX440,Asus FX 5200,Ati 9100,Ati 9200SE...
Why!I tried lots of things.Bios update, i845 driver update...
Please is there anyone who understand tis problem in MSI?
Thanks!...

Quote
Originally posted by volkankarakus
Hi this is my PSU model and spesifications
SOLARMAX
Model:KC300 ATX
Input 115V/230V AC 50/60
Output 300W Max
+5V 20A +3,3V
+12V 12A -12V
+5VSB 1,5A -5V
Thanks!
Weak PSU is all I could say. 300watts can't even support a P4 stablely, not even to talk about combining a P4 to any new VGA cards... Get a better 400watts or more PSU with +3.3v at @ least 26A, +5v at @ least 35A and +12v at @ least 18A.

HP ProBook 5220m Fan not working with battery power but work fine with adapter plugged in

Hi,
Any one have this issue?
HP ProBook 5220m (Bios Version F50) Fan not working with battery power but work fine with adapter plugged in.
This issue was found in my replacement motherboard. the original mother do not have this issue.
The origianl mother to be replace is due to can't power on after a power failure recovery. I believe was due to power surge killed the motherboard's power controller circuitry.
Appreciate any one can provide clue for resolving the problem.
I have tried to install speedfan to try my luck, but it can't any fan in the application to configure. (Bios Version F50)

@wheng
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Horrible fps problems, fans not working

Hi,
Whenever I play League of Legends on my 15 inch retina macbook pro, the game starts out smoothly with a consistent 60 fps. However, after a certain period of time, the fps severely drops to about 5. It never used to do this, but now it happens consistently. Also, the fans have not turned on in months; they used to always be on whenever I played League, but they seem to never turn on anymore. Could the fps problem be related to the fan not working? Please help, and thanks!

Sargeraspa,
Lenovo G770 has ThinkVantage System Update? I thought that is suppose to be for ThinkPad system only?
Go to the link below and Select Win 7.
http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?DocID=HT072970
Then update the BIOS and Energy Management driver.
*Non Lenovo employee*
I have a Y2P (i5) ... Feel free to ping me if you want me to test some applications with your Y2P if you have the same model. I don't mind keep doing recovery on it if needed .... =)

Win 10 Fan Not Working

Updated To windows 10 Fan Not Working Error At BootUp ..
Coolsense Is installed...

If after reinstall, issue persists, have a look at this Answer given in the other forum. It might be your answer too...........
http://answers.microsoft.com/en-us/windows/forum/windows_tp-windows_store/unable-to-launch-windows-apps/2c6ac3c1-fc6f-489c-893e-9e6d3b028c03?page=1

CPU Cooling Fan not working

Hi,
CPU Cooling fan not spinning and showing error on startup saying fan not working properly.MY HP Pavilion G6 laptop's Product number: B0P25PA#ACJ and Serial number: [edited by Moderator]. I want to replace the same. Can anyone tell me which model of fan would be appropriate?
Thnks in advance.
Thanks,
PSantra

Hi @Psantra ,
Thank you for visiting the HP Support Forums. I'm sorry to inform you that your post has needed some editing to remove personal information such as the Serial Number in your Post. From our Rules of Participation:
Protect privacy - yours and others'. Don't share anything about yourself that you would not want to see on a road-side billboard. Don't post contact or other personal information-your own or anyone else's-or any content that you receive in one-to-one communications without the author's consent. For example, don’t post your computer’s serial # or contact information publicly, and do not allow someone you don’t know to remotely take control of your computer.
If you need people to contact you directly, either ask them to send you a private message or subscribe to the thread so you will be notified when there are replies. You may also click on your name anywhere in the forum and you will be taken to your profile page, where you can find a list of threads you have participated in.
Sharing personal email addresses, telephone numbers, and last names is not allowed for your safety. If you have any questions feel free to send me a private message in reply.
Thank you
George
I work for HP

2540p fan not working

Hi,I bougth netbook hp 2540p windows 7 instaled,and have a problem with cooling fan.The fan not working on the battery ,working connected to power adapter all the time.have you any suggestions how to fix it.thx
This question was solved.
View Solution.

Windows 7 or Windows 8? You are likely set to passive cooling in power management while on battery which means the laptop will do almost anything rather than kick on the fan while on battery. It will slow the processor instead. If you shift to active cooling your battery will get eaten up very fast. In short, I think your system is probably fine and messing with it does not make any sense. However, here is some more information on passive vs. active cooling:
http://social.technet.microsoft.com/Forums/en-US/af0a536c-56f5-4811-b102-87ae2af6f53c/power-managmen...

Error 90B - Fan not working properly?

Hello, this is my first time here so please excuse me if I posted this in the wrong section.
First, general specs:
HP Pavilion dv6 Notebook PC
Windows 7 Home Premium 64-Bit
BIOS: InsydeH20 Version CCB.03.61.09F.21
Processor: AMD A6-3400M APU w/Radeon HD (4 cpus ~1.4GHz)
6g RAM
(If anything else is needed to help me ask, and I shall post it)
Last week I received an error 90B for my laptop's cooling fan. I was playing Guild Wars 2 and in the middle of playing my laptop shut down suddenly. When I turned it back on it presented the error I'm asking about. The thing is, the system wasn't overheating in the slightest and the fan was working just fine before it shut down. I've tried many fixes proposed on HP's website and from a couple of friends:
-Compressed air blown into the vents
-System restore to a point where the fan worked
-Hard reset
-BIOS update
None of those proposed fixes worked. However, I did find something that fixed it...for about ten minutes. I fiddled with the Catalyst Control Center and set my CPU power back to its default 1400 MHz, and I shut down my system. After I restarted it I miraculously didn't get the 90b error! You could imagine how happy I was. I shut it down one more time to see if the error was truly fixed, but lo and behold it showed up again.
The only change that could have caused the issue was me downloading a program called SpeedFan to monitor my system's temperature (I did NOT (I repeat, DID NOT) change any settings using the program - I purely used it to monitor the temperature.)
I cannot afford to have a repairman replace or look at my laptop as of now, we have bills to pay and food to get, and I absolutely NEED this computer to function. I have work to do, and classes to sign up for, and we have no public computers for miles. Please help me!

Not every fan error is a heat error. There is a sensor that detects a bearing that is wearing out or spinning that is out of round. You can sometimes limp it along for 6 months before the fan absolutely has to be replaced. When it does you will not be able to get past the error.

Eeepc 901 fan not working

Hello everyone! I installed Arch on my EeePC 901 and everything seems to run smoothly, until I noticed that the fan is not working. I did a little search on the forums, to check if someone already had to face something similar but with no success.
This is the output of pwmconfig:
# pwmconfig revision 5857 (2010-08-22)
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
Found the following devices:
hwmon0 is acpitz
hwmon1/device is coretemp
hwmon2 is eeepc
Found the following PWM controls:
hwmon2/pwm1
Giving the fans some time to reach full speed...
Found the following fan sensors:
hwmon2/fan1_input current speed: 0 ... skipping!
There are no working fan sensors, all readings are 0.
Make sure you have a 3-wire fan connected.
You may also need to increase the fan divisors.
See doc/fan-divisors for more information.
This is the output of fancontrol:
Loading configuration from /etc/fancontrol ...
Error: Can't read configuration file
And this is the output of sensors:
Adapter: Virtual device
temp1: +62.0°C (crit = +85.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +18.0°C (crit = +90.0°C)
eeepc-isa-0000
Adapter: ISA adapter
fan1: 0 RPM
I'm pretty a newbie and I don't know what to do, is there someone who can give me some advice please?
Thanks to all.

Thank you for your answer, sorry but I can't check the forums too often...
The Wiki page about my model dosen't give any advice on this subject.
I installed the eeepc-fancontrol package, the daemon is running but the fan is still dead
Here is my modules and daemons from rc.conf:
MODULES=(rfkill acpi-cpufreq eeepc_laptop asus_eee bluetooth snd-hda-intel)
DAEMONS=(syslog-ng crond dbus acpid alsa networkmanager bluetooth sensors eeepc-fancontrol lxdm)
Here is an extract of dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] ACPI: SSDT 3f7aeb80 004F0 (v01 PmRef CpuPm 00003000 INTL 20060113)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f6d28000 s31424 r0 d21824 u53248
[ 0.000000] pcpu-alloc: s31424 r0 d21824 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Initializing CPU#0
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] CPU 0 irqstacks, hard=f6408000 soft=f640a000
[ 0.003934] Initializing cgroup subsys cpuacct
[ 0.004052] CPU: Physical Processor ID: 0
[ 0.004056] CPU: Processor Core ID: 0
[ 0.004063] mce: CPU supports 5 MCE banks
[ 0.004081] CPU0: Thermal monitoring enabled (TM2)
[ 0.068794] CPU0: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02
[ 0.106708] CPU 1 irqstacks, hard=f64ca000 soft=f64cc000
[ 0.006666] Initializing CPU#1
[ 0.120050] Brought up 2 CPUs
[ 0.140706] ACPI: SSDT 3f7ae180 0023C (v01 PmRef Cpu0Ist 00003000 INTL 20060113)
[ 0.141330] ACPI: SSDT (null) 0023C (v01 PmRef Cpu0Ist 00003000 INTL 20060113)
[ 0.143480] ACPI: SSDT 3f7ae450 00724 (v01 PmRef Cpu0Cst 00003001 INTL 20060113)
[ 0.144055] ACPI: SSDT (null) 00724 (v01 PmRef Cpu0Cst 00003001 INTL 20060113)
[ 0.144612] ACPI: SSDT 3f7ae0b0 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20060113)
[ 0.145209] ACPI: SSDT (null) 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20060113)
[ 0.145428] ACPI: SSDT 3f7ae3c0 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20060113)
[ 0.146619] ACPI: SSDT (null) 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20060113)
[ 0.188472] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.800625] cpuidle: using governor ladder
[ 0.800771] cpuidle: using governor menu
[ 2.353676] ACPI: Requesting acpi_cpufreq
[ 2.672731] microcode: CPU0 sig=0x106c2, pf=0x4, revision=0x212
[ 3.000420] microcode: CPU1 sig=0x106c2, pf=0x4, revision=0x212
[ 11.170288] asus_eee version 0.39a1 init sucessfully
[ 11.170304] asus_eee informs writable=1 is dangerous: think before writing, do not let your CPU burns out!
And here is the output of lsmod:
Module Size Used by
fuse 60090 2
asus_eee 8416 0
rfcomm 28281 8
bnep 7062 2
i915 388286 3
joydev 7695 0
btusb 10048 0
arc4 1118 2
i2c_algo_bit 4615 1 i915
drm_kms_helper 29171 1 i915
drm 170915 3 i915,drm_kms_helper
usbhid 31733 0
microcode 8825 0
intel_agp 8752 1 i915
intel_gtt 11229 3 i915,intel_agp
iTCO_wdt 10705 0
iTCO_vendor_support 1545 1 iTCO_wdt
serio_raw 3709 0
coretemp 4702 0
i2c_i801 7088 0
pcspkr 1455 0
psmouse 70891 0
evdev 7630 19
uas 7277 0
agpgart 21967 3 drm,intel_agp,intel_gtt
soundcore 4378 1 snd
thermal 6563 0
i2c_core 16653 8 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,videodev,asus_eee
hid 67113 1 usbhid
video 9883 1 i915
ac 1796 0
battery 5085 0
button 3614 1 i915
eeepc_laptop 12813 0
pci_hotplug 20534 1 eeepc_laptop
sparse_keymap 2532 1 eeepc_laptop
acpi_cpufreq 5141 0
mperf 1023 1 acpi_cpufreq
processor 23783 1 acpi_cpufreq
sd_mod 26959 5
pata_acpi 2388 0
ata_generic 2391 0
ata_piix 19608 3
uhci_hcd 19776 0
libata 146119 3 pata_acpi,ata_generic,ata_piix
scsi_mod 112541 4 uas,usb_storage,libata,sd_mod
ehci_hcd 35958 0
I purged some clearly unrelated modules, sorry if the quotes are full of useless info but I don't know what I'm looking for...

Fan not working propely

Hello HP!
My laptop's fan is not working properly, it is sometimes slow, sometimes pulsating and sometime during playing game when the laptop heats up, the fan completely stops. the BIOS is lates. i dnt know what is the problem. I cleaned the fan and everywhere (in the laptop).
yesterday i reinstalled the BIOS and the fan was working perfect even during game the laptop didnt overheated but after a restart the fan was again working abnormal.
about laptop:
-Probook 4540s.
-core i7 @2.1
-8 GB RAM.
-AMD Radeon HD 7650m.
-Windows 7 ultimate 64bit.
-BIOS F.60 (Latest).
Thanks in advance.

Hello solo557770,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that your fan is not working correctly on your computer. I am providing you with an HP Support document: System Fan (90b) error message on startup as it has steps to help you resolve a fan that is not working correctly.
If you require additional assistance I would encourage you to post your product number for your computer. I am linking an HP Support document below that will show you how to find your product number. As well, if you could indicate which operating system you are using. And whether your operating system is 32-bit or 64-bit as with this and the product number we can provide you with accurate information.
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the requested information and I would be happy to provide you with assistance. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Y40-70 fans not working

I sent my computer in for a repair because of a faulty wifi card. A few days ago, I got it back, but now the fans aren't working at all. The temperature is constantly at around 70°C. I've already tried updating the bios, and even doing a factory reset, but the problem still persists. I have to use an external laptop cooler for it to be usable. I'm so tired of dealing with the problems with this laptop at this point.

Hi MustafaHashmi,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with touchpad not working in your Lenovo Y40-70 laptop.
Please try connecting external mouse and check for the issue. Also try to check in safe mode and check for the issue
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S

MSI GTX 680 TF3 OC 2GDR5 BOTH FANS NOT WORKING

]BOTH FANS OF MY GPU ARE NOT WORKING THEY ARE AT FULL STOP AND MANUALLY ALSO NOT SPINNING THROUGH AFTERBURNER UNLESS I APPLY IT AT MAX 88% BELOW THAT AND THEY COMPLETELY STOP ALTHOUGH AFTERBURNER IS SHOWING ME THEY ARE SPINNING WHAT CAN I DO IN THIS CASE? PLEASE HELP... WHEN I BOOT THEY SPIN FOR 1 SEC & AFTER THAT THEY ARE COMPLETELY STOP.. MY TEMPS ARE REACHING SKY HIGH . THE ONLY WAY TO USE IT BY RUNNING THEM AT 88% ALWAYS MANUALLY? BELOW THAT AND BOTH FAN STOPS.. PLEASE HELP :s

I see.
You can either find replacement fans online, or buy aftermarket cooler for GPU. Or as last solution: find a broken card that will cost not much, but it and replace heatsink with fans.
Or ask MSI, maybe they can redirect you to some store with fans:
>>How to contact MSI.<<
Also did you try to reinstall Afterburner? And are you able to test the card in different PC?

MSI N470GTX Twin Frozr II both Fans not working

I bought GTX 470 Twin Frozr II several year back
now the fans stopped working (not spinning at all)
I've cleaned the dust and did everything
can I get new fans for the card (My card is OUT OF WARRANTY)
how much new fans cost???
can anybody tell me????

fisrt one fan stopped working and later the other
i touched them and both FANS were too hot to touch
cable connections of both fans are fine
sometimes they spins but with very low RPM 200~400
few months back both fans were very free to move (i tried spinning with my hand when I was cleaning the card) now they are hard to spin like dust is inside the motor of the fan (I know fans are not of use anymore)
I already know about Arctic twin turbo II but i'm not spending that much money (I live in INDIA so the shipping charges are about 10$~13$), 65$ heatsink + 12$ shipping = 75$~78$
I want just fans not entire heatsink

MSI N560GTX-Ti Twin Frozr II fan not working

Hello Friends,
One of the fans is not working fine. It would start-stop in between. Would anyone if I can replace it from a MSI service center?
I live in Pune (India)
Thanks in advance!

typically you have to send the card for repair to msi
>>How to contact MSI.<<

Fan not working on AMD card pwmconfig

Similar Messages

Maybe you are looking for