Fans for cooling AMD Barton core??

Hi. i've read through most of the posts in the forum regarding the 'hot & spicy' issue of mega 180, and am planning of adding extra fans into my little black box. thing is, i notice the 2 CPU fans installed r quite small and slim. is there any replacement fans i can use? or i just pop in extra ones into the box? and how do i connect the power cables for the extra fans? my CPU went all the way up to 75 degree celcius when i was converting some video files. and my CDROM eject button in front stopped working. had to restart the system to get it working again.
p.s. i bought the system and asked the vendor to install all the components inside, so now i try my best not to fiddle with the CPU and heat sink part. any help would be appreciated.

Thats not to bad I was going the other way (taking it apart) I woke up and found it in bits I managed to figure out how it went back together. I hope.
If only that thermal paste would get here, I'd know for sure.

Similar Messages

Replacement fan for stock amd heatsink

hey to all, Anybody know of a good high cfm fan(dont care about noise) to replace a stock amd 60mm fan. also maybe what the stock fan cfm is? this is for another pc of mine. I found a all alum.evercool ( http://www.newegg.com/Product/ProductList.asp?Submit=ENE&N=2010110062+70002727+70001969&Subcategory=62&description=&srchInDesc=&minPrice=&maxPrice= ) its 23 cfm and am thinking maybe the extra metal might help out that stock heatsink. anybody have any ideas. thanks for the time Henry

HELLO, to all Well If your as cheap as I its worth a 7c drop by changing the fan on a stock amd 64 cooler. Thats almost as good as my zalman 7000b-cu cooler. I tried two different fans, a 60mm evercool rated at 25cfm, and a Tt 60cfm 80mm case blower fan (epoxied to stock plastic fan frame) the 60mm fan lower temps by about 4c at full 12v, the Tt blower got 7c lower on about half speed, ya its noisey on full but cant really hear it over any other fans on half, Then I took the stock amd fan and mounted it in the right side of my case behind the cpu & board blowing in and it dropped my mb temp by 2c, dosent stick out very much either being that it is so thin. used screen for a grill. Total cost $22.00, now idle at36c loaded 48c

AMD Athlon XP 2800 (Barton Core) will not post at FSB 166 MHz.

Per top of the board “stickys” I have read a great number of the post on this board and done my homework to provide as much technical info to help you help me. This should explain some of it’s lengthy nature.
Aside from Memory, HDD and Video card every thing else has been unplugged from board and power or stripped out of slots to isolate the problem.
Presently running BIOS: A6712 V. 1B
*As seen on face of MoBo: KT4V MS-6712 Ver:10A
*The Original Box bar code label: KT4V-L (601-6712-050)
K7, KT400. 5.1 chnl. S/W Audio, LAN, D-Bracket 2.
CPU: AMD Athlon AXDL 2800 DLV4D
Q334763K40034 AQYHA 0447APMW
Chip lable
Athlon XP (Barton) Low Power Processor (Model 10) 2083 MHz
OPGA Organic Pin Grid Array 1.50 Volt max. Temp. 85°C
512 KB L2 Cache 333 MHz System bus (166 MHz FSB) x 12.5
Memory: x3- PC 2700 512 mb DDR 333 Super Talent
And shows at post as running 333MHz. MemTested to 1,000% with first 1 stick, then all 3 sticks presently on bios A6712vms.1B0. at fsb 100MHz (aprox. 24hr.) I even installed and ran other AMD utillitys while MemTest was running to “stress” the system memory with zero errors. During this period I checked Windows Task Manager > Performance, CPU usage at 100%, PF usage 1.35gb. No Probs.
Video card: Removed: MSI AGP-8X Ti4200- VTD8X 128 MB DDR 533MHz
Replace with: PCI card (to rule out AGP card prob.) Gilmont, nVidia 64mb
(also tried Matrox AGP 32mb card with no different results then above cards)
Power Supply: L&C Model: LC-B350 ATX = 350 watt
      115/130v      B/4a      60/50 hz
      +3.3v/+5v   1+12v   -12/-5v    +5vsb
      28a   35a    16a    0.8a    0.3a   2a
   +3.3v combined load 200w
Cooler: Slim Volcano 10+, P/N A1671, rated for up to AMD Athlon CP 3400+ & fresh heat sink compound. Freshly re-seated.
All PCI slots empty as I attempt to run bare bones to eliminate problems. (except now running Vido card in 1 slot)
Floppy Drive: ribbon unplugged from board
HDD-0: Seagate 8 gb master, (HDD tested w/no errors)
O/S: Win. XP w/sp2
HDD-1: slave/ unplugged from ribbon and power
Sony CD-Rom: Unplugged from PCI slot and power
SATA/RAID-usb 2.0 card and other HDD’s, removed and not included till Sys. runs at full potential.
Exterior HDD and Burner beyond the scope here and not attached.
O/S Win. XP-sp2
BIOS I have tried: The original; Ver:10A, ran fine on Athlon XP 1600 (1400 MP) 3 years.
•   Then with MSI Live Update 3: Installed v. 1c which couldn’t run FSB 166MHz (MSI:” Fixes system reports incorrect message for AMD 3200+ CPU.
- Supports Sempron L2 512K 3000+ CPU.)
However, v. 1.c did not work and would not post at all with the newly installed Barton AMD-XP 2800. [frankly this attempt was months ago and I do not remember whether it would post at the slower 100 and 133 FSB speeds, and also to muddle my memory further I was upgrading an A7N8X-D with a Barton XP 3000 and having similar problems on the ASUS,,, which is now running fine at full potential. ; - p
•   Then I selected and flashed A6712 V 1.7 122602, boots and runs Win.XP-sp2 at FSB 100MHz & 133MHZ. (MSI:” Supports AMD Barton XP2800+ (FSB333) CPU
-Fixes system sometimes will have IDE CRC error -Fixes D-bracket2+USB keyboard, cannot use keyboard on DOS mode.)” which couldn’t run FSB 166MHz.
I checked with the Tech. at the local shop where I purchased the KT4V MoBo. He suggested I try a different BIOS but he didn’t specify which one. He is a personal friend and admits to some bad luck and dead boards due to flashing bios so reluctant to mess with it.
•   Now running: A6712vms.1B0 – MSI hid this BIOS V. found here:
•   http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=362&kind=1
•    On a different page than the 2 versions mentioned above. http://www.msicomputer.com/support/bios_result.asp
•    No wonder people are frustrated and confused about different MoBo versions there ID #’s and the BIOS versions them selves as seen on this news board. MSI’s fault, no fault of anyone here trying to help.
A6712vms.1B0
Runs fine at FSB 100 (shows as XP 1250+) and FSB 133 (shows as XP 2200+) Booting to Win. XP-sp2 on CMOS, default setup other than minor tweaks to accommodate MSI Ti 4200 AGP 8X 125mb graphics card or Gilmond PCI card. But which couldn’t run FSB 166MHz .
No post at FSB 166 mhz (once, it did flash a post screen stating AMD Athlon XP 2800 for about 2 sec. before going blank) Manual power down. Just now I rebooted with FSB 166, and again saw the AMD Athlon XP 2800 at top of the post screen as I hit pause break,,,, then the machine power crashed to Off. Once it even loaded Win.XP-sp2 but crashed to power off with in 2 min.
I must have booted this beast a dozen times or more after Clear CMOS jumper each time it went to blank screen with mach. still running. Start over; set Default settings and work up with FSB 100, 133, each time to read what POST says and see if it will boot to O/S.
Btw: I have looked for clear evidence through the not so specific descriptions MSI uses to separate these board model #s and may be part of my current problem with correct board ID = correct BIOS ID.
Found here:
[VIA] unofficial FAQ for KT4 series motherboards
https://forum-en.msi.com/index.php?topic=6090.0
Eg: - KT4 Ultra (MS-6590), 6-channel hardware audio codec
• KT4 Ultra (Pure Version)
• KT4 Ultra-B (Bluetooth ready)
• KT4 Ultra-BSR (Bluetooth ready + Serial ATA RAID)
• KT4 Ultra-FISR (Bluetooth ready, Serial ATA RAID, Gigabit LAN, IEEE 1394)
- KT4V (MS-6712), 6-channel software audio codec
• KT4V-L, with onboard 10/100 LAN
- KT4M (MS-6596) micro-ATX board
• KT4M-L, with onboard 10/100 LAN
- KT4A Ultra, (MS-6590) NEW!! based on KT400A chipset
• KT4A Ultra (Standard Version)
• KT4A Ultra-SR (Serial ATA RAID)
• KT4A Ultra-FISR (Serial ATA RAID, Gigabit LAN, IEEE 1394)
And a very similar version of this on Official MSI site. Both seem to try and make a difference between modles with on board Lan, and Blue Tooth ready.
Take a look at my original box sticker:
*As seen on face of MoBo: KT4V MS-6712 Ver:10A
*The Original Box bar code label: KT4V-L (601-6712-050)
K7, KT400. 5.1 chnl. S/W Audio, LAN, D-Bracket 2.
Yup, it says all this on the sticker and the in the manual and verified on the MoBo. So I can only guess at all parts of the puzzle as they gave them to me which lead me to the afore mention BIOS versions I ran, or am running. The sticker points to nearly half of the boards above except for the MS-6712 and the Ver:10a which is what I based my BIOS choices on. If someone knows differently and can lead me to official Nfo with a better answer I’m all ears.
Just saw this: Latest Official BIOS : KT4 MS-6590 (1.4), KT4V MS-6712 (1.8 ) , KT4M MS-6596 (1.1)>>Here: [VIA] unofficial FAQ for KT4 series motherboards
« on: 24 October 02, 05:14:04 » But these links and all but one link in this ‘sticky’ are broken .
So if (1.8) is the Latest Official BIOS for KT4V MS-6712 then what is this at the Official MSI SITE ?
KT4V
BIOS Type
AMI® BIOS     File Sizes
485KB
Version
1.C     Update date
Update Description   -Support Sempron L2 512K 3000+ CPU.
BIOS Type
AMI® BIOS     File Size
Version
1.B     Update date
2004-8-9
Update Description   Support Sempron 2200+/2300+/2400+/2500+/2600+/2800+ CPU.
BIOS Type
AMI® BIOS     File Sizes
485Kb Version
1.A     Update date
2004-5-13
Update Description   - System is unstable to run 3DMark03 with ATI 9600 PRO
- Add "PS/2 Keyboard Detection" Function.
- Support AMD 2400+ CPU.
BIOS Type
AMI® BIOS     File Sizes
514KB
Version
1.9     Update date
2003-7-29
Update Description   -Fixed Adaptec 2100S SCSI card cannot be used
-Modify CPU temperature detection
-Support boot from Onboard LAN
BIOS Type
AMI® BIOS     File Sizes
514KB
Version
1.8     Update date
2003-2-12
Update Description   -Support AMD Barton XP3000+ (FSB333) CPU
-Add "CPU Halt Command Detection" item in the BIOS Setup
Please also keep in mind I’m not trying to scuff anyone’s shoes…I just want to get what’s right for my board so that it and the CPU can live up to their full, "as advertised" potential and run with the other 3 big dogs under my desk.
This seems descriptive enough and rather lengthy. Just doing my homework and reporting my findings so I won’t include actual CMOS settings unless requested. I have notes on all settings I currently use to boot with this problem.
Other Dogs:
ASUS A7N8X-D running Athlon XP 3000 barton core 10 (runs fsb 400..whoknew?), Mem:2.5gb Super Talent
ASUS A7M266-D running Athlon XP 2800 (mp), Mem: 3gb Super Talent
Athlon XP 2800 (mp)
I don’t want to boar you with the details.
Yes, and the above have been upgraded w/new chips GFX cards and BIOS,,, NP.
Cut to sound track: Down on the BIOS again,,, wasn’t that Creedance Clear Water Revival?
Any suggestions or insights are much appreciated.

Welcome, and thank you for a thorough input! Hope I don't miss something you already said!
Quick version: Try setting processor voltage to 1,5 volt.
Long version:
Posting at wrong FSB can be put down to two things:
1 The processor isn't what you thought it is, but I think you eliminated that.
2 The system cannot run the processor at the correct speed. Mainly this has to with overheating, and/or that memory and processor cannot cooperate. This must be it, as you noticed the processor is correctly recognised.
You have little connected right? Then the best thing would be to pull power cable out. Take the motherboard and redo the seating of the processor, this is much better done with motherboard taken out.
At the same time, I suggest you clear CMOS. Should always be done when changing processor, and I've noticed on the Internet there are a few 1,5V XP2800 around.
http://64.233.183.104/search?q=cache:Q4eIa6OhudcJ:forums.amd.com/lofiversion/index.php/t47487.html+AXDL2800DLV4D+problem&hl=sv&gl=se&ct=clnk&cd=1

Where can i buy a new cooling fan for my Compaq Presario CQ61-330SO Notebook PC?

like the headline says.
Where can i buy a new cooling fan for my Compaq Presario CQ61-330SO Notebook PC?
it died almost a month ago and i have been searching for a new one since
I searched all over HP's website and cant find any information about that, not even the name of the fan.
som help here would be wary appreciated

Hi,
You can order from here:
http://h20141.www2.hp.com/hpparts/?cc=US&lang=EN&jumpid=hpr_r1002_usen
and part # is in here (page #3-4):
http://h10032.www1.hp.com/ctg/Manual/c01868653.pdf
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

What is the best laptop cooling fan for a macbook pro?

I have my macbook on basically all day every day and I just want a nice cooling fan for underneath it so it doesn't overheat on me

I've never had any overheating issues, even when it is hard at work with several VMWare Fusion instances running concurrently. Just placed it on top of a Roadtech Coolpad (a passive laptop stand) and it's kept its cool thus far.

Cooling fan for quicksilver

i am looking for a new cooling fan (cpu fan) for my quicksilver 733.
it has part number : 2410ML-04W-B47
can someone please direct me in the right way
thank you

Hi, lab specialist!
Check here:
http://www.allmac.com/shop/productinfo.php?cPath=2_19_147&productsid=3372
http://store.yahoo.com/hardcoremac/g4qucafan.html
http://www.welovemacs.com/9224580.html
http://www.macsupportstore.com/dept.asp?page=2&dept_id=01-001-050&so=0
Gary

Will a K7N2G-ILSR run a Barton Core AMD XP 3000+

Will a MSI K7N2G run a Barton Core AMD XP 3000+ (333Mhz FSB)??????
If so how do you set the FSB to 333Mhz??

yes and you set it to 166,333 is a ddr speed
it may mean getting a newer bios to get it recognised

KT4 Ultra-SR (MS-6590) dont work with AMD Barton 2500+

;( Please help me any1.
I have MBO KT4 Ultra-SR (MS-6590) with CPU AMD Barton 2500+ and i have a big problem. System corectly boot only if a select CPU FSB Clock = 100 MHz (CPU Ration/CPU Vcore/DDR Voltage=all AUTO). When a select CPU FSB Clock 133 or 166 MHz, system begin run corectly and after few second turned OFF. I selecting SDRAM Frequency on=AUTO/266/333/400 MHz but not working. My old CPU is AMD XP Palomino 2100 MHz and work fine with KT4 Ultra MBO. I upgrade BIOS with 1.4 version. I change memory module with PQI (PC 2700/256 MB) and JETRAM (PC 2700/256 MB) but is same ":censored: ". System dont work. Bad CPU Barton 2500+? I dont no. Please help me any1.
My System:
MBO KT4 Ultra-SR (MS-6590)
CPU AMD Barton 2500+ (FSB 333)
Memory DDR Samsung 2x256 MB (PC 3200) K4H56083D-TCC4
Cooler SPIRE WhisperRock IV+Artic Silver 3
HDD Seagate Baracuda 120 GB SATA
PSU Enermax 300W EG301P-VE(FMA)
VGA Saphire ATI Radeon 9100 (64 MB+TV/DVI-out)
DVD-ROM Pioneer 120S (16x speed)
CD-RW MSI CR52-A2 (52/24/52, Atapi)
FDD Teac 1.44 MB
Creative SoundBlaster Live! 5.1

Most of the time, this sort of problems arise because of power suppliy issues.. U have a enamax 300W PSU which is a VERY GOOD PSU but might just be on the line...
If u can, try swapping the PSu for a good 400 or a 420W PSU.. this might solve your enigma.. I really dont think this is your processor...
Read this two articles on PSu wrtten by one moderater which will aid in solve in fixing your problem (PSU1 , PSU2 , Troubleshooting Guide )
Best of luck
RAsika

I am running Photoshop CC 2014 on Windows 8.1 with an AMD quad core processor and AMD E1-2100 APU with AMD Radeon HD 8210 Graphics Card. I have installed the latest driver version 13.152.0.0. When I activate puppet warp, the mesh appears over the image an

I am running Photoshop CC 2014 on Windows 8.1 with an AMD quad core processor and AMD E1-2100 APU with AMD Radeon HD 8210 Graphics Card. I have installed the latest driver version 13.152.0.0. When I activate puppet warp, the mesh appears over the image and I can place the first pin. However, when I go to add the second pin, Photoshop crashes. I have tried with on a new, blank file, with just a few lines on it, but, as soon as I place the first pin, the image disappears, and then, as soon as I click anywhere else in the image, Photoshop crashes. I have followed all the online advice about settings under the Preferences/Performance interface, but nothing fixes the problem. Can anyone please help?

BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, such as total installed RAM, scratch file HDs, video card specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
A screen shot could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

128-bit floating point numbers on new AMD quad-core Barcelona?

There's quite a lot of buzz over at Slashdot about the new AMD quad core chips, announced yesterday:
http://hardware.slashdot.org/article.pl?sid=07/02/10/0554208
Much of the excitement is over the "new vector math unit referred to as SSE128", which is integrated into each [?!?] core; Tom Yager, of Infoworld, talks about it here:
Quad-core Opteron? Nope. Barcelona is the completely redesigned x86, and it’s brilliant
Now here's my question - does anyone know what the inputs and the outputs of this coprocessor look like? Can it perform arithmetic [or, God forbid, trigonometric] operations [in hardware] on 128-bit quad precision floats? And, if so, will LabVIEW be adding support for it? [Compare here versus here.]
I found a little bit of marketing-speak blather at AMD about "SSE 128" in this old PDF Powerpoint-ish presentation, from June of 2006:
http://www.amd.com/us-en/assets/content_type/DownloadableAssets/PhilHesterAMDAnalystDayV2.pdf
WARNING: PDF DOCUMENT
Page 13: "Dual 128-bit SSE dataflow, Dual 128-bit loads per cycle"
Page 14: "128-bit SSE and 128-bit Loads, 128b FADD, 128 bit FMUL, 128b SSE, 128b SSE"
etc etc etc
While it's largely just gibberish to me, "FADD" looks like what might be a "floating point adder", and "FMUL" could be a "floating point multiplier", and God forbid that the two "SSE" units might be capable of computing some 128-bit cosines. But I don't know whether that old paper is even applicable to the chip that was released yesterday, and I'm just guessing as to what these things might mean anyway.
Other than that, though, AMD's main website is strangely quiet about the Barcelona announcement. [Memo to AMD marketing - if you've just released the greatest thing since sliced bread, then you need to publicize the fact that you've just released the greatest thing since sliced bread...]

I posted a query over at the AMD forums, and here's what I was told.
I had hoped that e.g. "128b FADD" would be able to do something like the following:
/* "quad" is a hypothetical 128-bit quad precision */
/* floating point number, similar to "long double" */
/* in recent versions of C++:                       */
quad x, y, z;
x = 1.000000000000000000000000000001;
y = 1.000000000000000000000000000001;
/* the hope was that "128b FADD" could perform the */
/* following 128-bit addition in hardware:          */
z = x + y;
However, the answer I'm getting is that "128b FADD" is just a set of two 64-bit adders running in parallel, which are capable of adding two vectors of 64-bit doubles more or less simultaneously:
double x[2], y[2], z[2];
x[0] = 1.000000000000000000000000000001;
y[0] = 1.000000000000000000000000000001;
x[1] = 2.000000000000000000000000000222;
y[1] = 2.000000000000000000000000000222;
/* Apparently the coordinates of the two "vectors" x & y       */
/* can be sent to "128b FADD" in parallel, and the following   */
/* two summations can be computed more or less simultaneously: */
z[0] = x[0] + y[0];
z[1] = x[1] + y[1];
Thus e.g. "128b FADD", working in concert with "128b FMUL", will be able to [more or less] halve the amount of time it takes to compute a dot product of vectors whose coordinates are 64-bit doubles.
So this "128-bit" circuitry is great if you're doing lots of linear algebra with 64-bit doubles, but it doesn't appear to offer anything in the way of greater precision for people who are interested in precision-sensitive calculations.
By the way, if you're at all interested in questions of precision sensitivity & round-off error, I'd highly recommend Prof Kahan's page at Cal-Berzerkeley:
http://www.cs.berkeley.edu/~wkahan/
PDF DOCUMENT: How JAVA's Floating-Point Hurts Everyone Everywhere
http://www.cs.berkeley.edu/~wkahan/JAVAhurt.pdf
PDF DOCUMENT: Matlab's Loss is Nobody's Gain
http://www.cs.berkeley.edu/~wkahan/MxMulEps.pdf

Labview 2011 executable does not run on AMD Quad Core

I have recently bought a brand new Toshiba Satellite with AMD Quad Core- A8-4500M 1.9GHz processor and Windows 7 OS. It does not run any labview executables. It runs on all my Intel machines without any problem. This is the first AMD ever bought (and the last). I need help in resolving this problem.
When I run an exe on the AMD, under Task Manager\Processes, I do see *.exe process running, but the Memory usage goes up and tops off at 100% and then it returns to 0. It's like a saw tooth waveform of memory usage, as if it's looking for some missing files. I have cleaned up the computer twice now and even a simple Add Two Numbers.exe does not work on this AMD.
Any clue, anyone? please?

I believe you are running into the problem described in this KB.
http://digital.ni.com/public.nsf/allkb/4734A6405B123FA58625799900813593
Regards,
Jon S.
National Instruments
LabVIEW R&D

Recommendations for cooling pad for 15" MBP

Hi, I have found that I am using my macbook pro for watching movies and things in my bed a lot of the time. The computer gets really hot and the fans seem like they are going fast all the time.
I was wondering if there are any recommendations for cooling pads that could help prevent this.
Thanks for any help.

To supplement the comments but Scott, I also believe that a cooling pad is not necessary. Your computer is engineered to cool itself. If you are concerned with higher than normal fan speeds and want to continue use on your bed, I would recommend something with a flat and hard surface such as a book or clipboard.
Many laptop coolers feature active cooling using fans. Note that many of these are not engineered specifically for your Macbook Pro. I've used a Zalman cooler that pushed air towards the bottom of my laptop and actually increased operating temperatures. I hypothesize that the directional air and angle of the cooler impeded the Apple designed internal passive/active cooling of the laptop. These devices are also burdensome in that you need to supply power to them.
In the end, the rather pricy Zalman cooler was more effective has a flat and hard surface than as an active cooler.
There are alternatives to active cooling, including a mat that absorbs quite heat energy by transforming solid crystals into a liquid. From what I've read these are effective for some time, but once all of the crystals have been liquified, is longer as effective (at least until the crystals re-solidify).
If you happen to find something that works particularly well with the Macbook Pro, please do share. Otherwise, a simple hard and flat surface will likely work very well and reduce heat/fan speeds while using your computer on an insulator (the bed).

Hp Pvillion G6 2005ax with AMD Quad Core is showing blank Screen after latest BIOS Update

Hi
I have strange issue after the Hp Software Update. Recently i have connected to High Speed internet and Hp Asistant shown a Bios update for my System and i chose download. after that my Hp Pvillion G6 2005ax with AMD Quad Core is showing blank Screen and Caps Lock button Blinks Randomly and F12 Button also on. Kindly Suggest a Solution for this. I have been irritated by Hp Customer Care support.
My Mobile No. [Personal Information Removed]
Email ID is [Personal Information Removed]
for any help you can send or i am availbale on above contact address.

Hello , Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel. I read your post about the BIOS, and wanted to assist you! The blank screen and blinking of your Caps Lock, is the system trying to give you the error code for the issue your notebook is having. You can review the following document for further assistance, if needed:HP Notebook PCs - Computer Does Not Start and Emits an LED or Beep Code Please note the blinking sequence of your Caps Lock, and follow the instructions in the document above. From the information that you provided, it is possible that the blink code will be related to a BIOS error. You can always try performing a System Restore, to set the notebook back to a previous working point. You can also try checking this site for BIOS drivers. Once there, you can select your Operating System and click "Update", you should be able to access and download the BIOS drivers. If you downloaded the latest driver from that site, try uninstalling the driver and installing the previous version. Please let me know if this information was helpful by clicking the thumbs up below.
Have a great weekend!

Xp2600(barton Core)

I,m trying to run the new XP2600(barton core) on this board the system will power up but not post (4 red lights) will i have to mode the board by removing the chip C37. i,m assuming that it is a voltage problem thats preventing it running....
i,m not the best person with a soldering iron. can this problem be solved buy a bios flash....if so then were can i find a more upto date bios ver than the one i have (3.7) or will it be quicker and easyer to replace the board with a newer version if so which board is the best (MSI)at the moment

the board will not run a 166 fsb cpu at its correct speed evan with the mod
it has only the dividers to run a 133 fsb in bios cpu
your psu is way to small
you need to mod it for thrdrd support
https://forum-en.msi.com/index.php?threadid=23762&sid=

CPU FAN FOR HPE-350T

I am looking for the part number for a replacement cpu fan for my HPE-350t.
Thank you
This question was solved.
View Solution.

HI
your product motherboard is from MSI MS-7613 .. and it having socket Socket 1156
purchase cooler master or any cup fan for socket 1156.. you can easily get it from any store..
Hope it will solve your quiery..
**Clicking on the Kudos! white star is a nice way to say thank you on any post that helped you or resolved the problem.**
**Selecting "Accept as Solution" for a reply that solves your issue helps others who are searching the web for an answer**

Fans for cooling AMD Barton core??

Similar Messages

Maybe you are looking for