Fascinate lost network connection after last Froyo update.

Anyone know how to fix this issue. After updating to the knew froyo upate last month my sons phone lost network connection and won't connect. It doesn't even show up in the settings for him to be able to connect. He can still make calls and connect but nothing data wise. Plus he still gets missed calls so that update never worked for him either. Please help and thanks.

I understand how frustrating this must be. My personal device had this problem and I found a solution that worked for me. Hopefully it will work for you as well.
1. Put the device in Airplane mode (hold power button and select airplane mode)
2. Wait 3 minutes for changes to take effect. You should see the airplane icon in the notification bar as well as the airplane lock screen.
3. Power the device off and wait 15 seconds.
4. Power the device on. Once sense loads, turn airplane mode off.
5. In the settings>Wireless & Networks Menu, check the box entitled "Mobile Network"
6. Everything should re-provision and data should be restored.
If the steps above do not resolve you issue you may want to try a master reset. Resetting the phone deletes all data, including downloaded applications, and resets the phone back to its initial state—the state before you turned on the phone for the first time.
Important: Make sure to back up important data you have on the phone before you reset your device.
Master Reset:
From the home screen, touch Menu
Touch Settings 
Touch SD & phone storage
Touch Factory data reset
Tap Reset phone 
Tap Erase everything
Reset may take anywhere from 1 - 10 minutes for reset and restart depending on amount of data on device.
I hope this information has been helpful.

Similar Messages

  • Lost network connection after standby on Satellite P200

    Hi
    Laptop Satellite P200
    OS VISTA 32
    When I stop working with laptop I usually close monitor and when next time open laptop computer lost network connection.
    Then I have to renew IP config and internet start working.
    Does anybody know why and how to avoid this?
    End I still want to use standby options.
    Tnx for any idea
    Sandi

    Hi
    In your case I recommend updating the BIOS and to enable the option Wake up on LAN in BIOS and in the Vista.
    In Vista you can enable this in device manager -> LAN card properties -> Advanced tab
    Additionally a LAN driver update would be advisable.

  • Lost network connection after update

    I waited a little long to update (~4 months) and am paying the price.  The recent update broke X as well as my network connection (and who knows what else!).  When I type ls /sys/class/net/, all I get is lo@.  I'm a little rusty with Arch as I was really really busy with school.  Do you have any suggestions for fixing this?  Here is my rc.conf if it helps:
    LOCALE="en_US.UTF-8"
    DAEMON_LOCALE="NO"
    HARDWARECLOCK="UTC"
    TIMEZONE="US/EASTERN"
    KEYMAP="us"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    VERBOSE="3"
    MODULES=()
    UDEV_TIMEOUT=30
    USEDMRAID="NO"
    USEBTRFS="NO"
    USELVM="NO"
    hostname="srv"
    interface=
    address=
    netmask=
    gateway=
    NETWORK_PERSIST="no"
    DAEMONS=(hwclock syslog-ng network netfs crond gpm bitlbee dbus sshd)
    Anything else I should post?  Thanks for your help!

    I was on vacation for a week, but now I'm back.
    kandrews wrote:
    Unfortunately, I cannot paste in these directories because it appears that usb is completely shot as well and I don't have a floppy drive (nor a floppy for that matter).  At least, I believe so because I stuck in a stick and ran:
    dmesg | tail
    and didn't see anything about a usb being registered by the system.
    Neither ifconfig or ip are installed.  So that is also a considerable issue.  Is all hope lost other than getting a live CD of ubuntu, spending a day copying files off of the hard drive and reinstalling?
    Sorry, I must have been really tired when I typed this.  Both programs (ifconfig, and ip) are in /sbin/.  I'm betting I tried 'sudo su' and they weren't on the path and being out of it, I assumed the wrong thing.  I'm going to try and mount a usb again to see if I messed that up as well...
    I still don't have an eth1 or eth0.  But maybe all hope is not lost.
    Update:
    No device nodes are created in /dev/ for usb drives, and my computer won't even power them unless I do it at boot.  I also noticed that my keyboard doesn't work at all during grub.
    ewaller wrote:Does the kernel referenced in the output of uname -a have a corresponding directory in /lib/modules ??
    I am wondering if the kernel on the boot partition somehow did not get upgraded when we moved up to 2.6.2939
    Yeah it does.  So no luck there.
    Last edited by kandrews (2011-06-24 16:44:41)

  • Lost network connection after SW update

    First time poster, relative newbie to Mac. I blindly updated to 10.4.11 and then found that my Mini had no network connection, yet my Ministack external FW HD and WinXP (thru BootCamp) will still connect wirelessly to my Westel router which has not been touched throughout this ordeal. My network is still shown and even offered to me for use during boot, but fails to connect. I have thrown every switch I can find in sys prefs to no avail. I have been asked for a WEP password, but security is switched off (in prefs and router), and I never used a PW before. I've spent hours Googling this topic, but can't find an exact match to my situation. I don't have the Mac knowledge to undo the update, or even know if it can be done. I can't understand how the bootable external HD can share the connection, but the "host" computer can't use it. Gotta be a setting wrong somewhere, eh? Please help.

    A warm welcome to the forums!
    Tons of similar posts, but not too many with the same cause fix.
    If you haven't done regular maintenence like Disk validate/repair, Permissions fixes, etc, ete.
    Then you Might give a try with Applejack...
    http://www.versiontracker.com/dyn/moreinfo/macosx/19596
    After installing, reboot holding down CMD+s, then when the prompt shows, type in...
    applejack AUTO
    Then let it do all 5 of it's things.
    At least it'll eliminate some questions if it doesn't fix it.
    The 5 things it does are...
    Correct any Disk problems.
    Repair Permissions.
    Clear out Cache Files.
    Repair/check several plist files.
    Dump the VM files for a fresh start.

  • Satellite Pro U400 - Lost network connection after suspend

    I have a Toshiba Dynadock. My network is connect directly in dynadock.
    When suspend my Satellite Pro U400 and after restart for continue working I lost my network connection. Then I shutdown my computer and disconnect/connect Dynadock I can continue working.
    What's the problem?
    Version software Dynadock is 2.0

    Hi
    I see you have switched from Vista to XP.
    First of all I recommend updating the BIOS.
    As Im not mistaken you should find a newer BIOS version on the Toshiba European driver page.
    Then you have to update the Win XP to the latest state!
    The XP should be up to date and all service packs, patches and MS fixes should be installed in your notebook.
    Then access the device manager and mark in every USB root hub you have to disable the option called Allow the computer to turn off this device to save power
    You can find this option in properties -> Power management tab

  • Lost OS X after last security update

    G4 Yikes. OS X 10.3.x (8 maybe?) on one partition and 9.2.2 on another.
    So last week I used Software Update and d'led several updates, including the security update (which I heard has caused problems). During the install I got a gray screen, and the hard drive emittid a clicking sound (I thought it died). Thankfully I have been able to reboot to 9.2.2, but not OS X. I can no longer select OS X as the startup drive. I ran the disk utility from the 10.3 CD and from 9.2.2 but I can't repair OS X.
    However, when in 9.2.2, OS X is visibile and I can browse files, leading me to believe this is fixable.
    Is this related to permissions? How can I reset them? I tried to run the disk utility in OS X from 9.2.2 with no luck.
    Is there a way to delete or uninstall the last set of updates? Is there a way I can run command line instructions?
    This is getting frustrating. Any helps is appreciated.
    Thanks
    G4 Yikes   Mac OS X (10.3.8)   Also 9.2.2

    Hello Neal,
    This may help:
    The following was contributed by Fumiaki Kawashima.
    The error message, "Error: The underlying task reported failure on exit (-9972)" is a serious filesystem error in the Mac OS X Core Foundation. The problem can also lead to other critical errors such as "Keys Out of Order," "Invalid node structure" and/or "Invalid sibling link." The causes and scenarios vary. Troubleshooting a solution may depend upon computer configuration and whether the -9972 error is accompanied by other critical errors. This issue can also lead up to a kernel panic. If the error occurs when an external FireWire device is connected, disconnect it until you verify the device's compatibility.
    Symptoms:
    In most cases, you are unable to restart from Mac OS X.
    * A volume is grayed out or not mounted with or without a kernel panic.
     * A folder with a flashing question mark may appear.
     * A bad partition map may be reported.
     * A target disk mode solution may not work.
     * Most likely, Disk Utility, Norton Utilities, TechTool and DiskWarrior cannot fix the issues.
     * The high level disk format (Standard format) may unable to perform.
     * You may unable to re-initialize the hard drive.
     * A disk physically malfunctions in the worst case.
    Example of an accompanied error message:
    DiskWarrior normally fixes 1 to 6, but cannot fix errors 7 to 10 if the symptoms are very bad. There is no definite case.
    01. Volume check failed
    02. Invalid B-tree Header
    03. Invalid map node
    04. Invalid extents entry
    05. Invalid clump size
    06. Incorrect block count file
    07. Invalid node structure
    08. Overlapped extent allocation
    09. Keys Out of Order
    10. Invalid sibling link
    Possible causes:
    * Third-party FireWire device or enclosure, or other peripheral devices.
     * Third-party mass storage drives or PCI card issues.
     * Incompatible third-party kernel extensions.
     * Mac OS X installer disc is improperly treated.
    Solutions:
    If possible and needed, back up data before troubleshooting. Methods (4) and (5) are for Power Mac desktop computers other than G5 models. The best bet is method (4) if you encounter multiple bad errors.
    1. Unplug the power cord. Disconnect all third-party hardware except Apple keyboard and mouse before you start.
    2. Do NOT re-install any third-party software/hardware until you completely solve the issue(s) and carefully investigate the compatibility with Mac OS X 10.3.x you install.
    3. If another critical error "Invalid sibling link" is detected at any phases, disconnect and reconnect all internal power cords and data cables for hard drives and any ATAPI device. To do so, you may need to read the computer's CIP Instructions in advance. Normally, you do not need to remove third-party RAMs.
    Method 1:
    (1) Start up from Mac OS X 10.3.x Panther Full Install CD or DVD.
    (2) Re-initialize and re-partition the hard drive. RECOMMENDATION: Select "Zero all data" option if "Invalid node structure" or "Keys Out of Order" error is detected.
    If this method is of avail, go to Method 2 or greater.
    Method 2:
    (1) Start up in Mac OS 9.2.2 and shut down the computer.
    (2) Start up from a copy of a Disk Warrior bootable CD for Mac OS 9.2.2.
    (3) Run DW to fix the damage(s).
    Method 3:
    (1) Unplug the computer.
    (2) Find a second ATA drive and jumper it as MASTER. Jumper the hard drive in question as SLAVE. Verify the jumper pin settings.
    (3) Install Mac OS 9.2.x system on the MASTER drive, and update it to Mac OS 9.2.2.
    (4) Start up from Mac OS 9.2.2. Re-initialize and re-partition the damaged hard drive with Drive Setup using the "Zero all data" option. Unplug the computer and reconfigure the jumper pin setting on the repaired drive for MASTER and the second drive for SLAVE.
    (5) Restart from Mac OS X 10.3 Panther full install CD. Re-initialize and re-partition the repaired drive to install Mac OS X 10.3. Update to Mac OS X 10.3.7 via Software Update. Repair the disk permissions after each Mac OS X 10.3 installation and Mac OS X 10.3.7 update.
    You may want to try starting up from Mac OS 9.2.x Full Install CD instead of from (2) to (4).
    Method 4:
    (1) Find a desktop computer that has an ATA controller PCI card (SCSI environment) and has two hard drive bays. This will make your damaged drive appear as a quasi-SCSI hard drive. Mac OS 9.2.2 must be pre-installed on the computer. I recommend a host computer that installs an Ultra DMA/xxx or xxx (ATA-x) interface equal to or better than the damaged drive with backwards compatible.
    (2) Set the host computer's primary drive as MASTER and your damaged hard drive as SLAVE and install the damaged drive in the second drive bay of the host computer. Verify properly configured jumper pin settings in advance.
    (3) Start up the host computer from Mac OS 9.2.2. Launch the "Drive Setup" utility. Re-initialize the damaged disk on the second drive using the "Low level format" option. It may take hours but less than "Zero all data" option. Note: Normally, a low level format with a quasi-SCSI drive takes much less (30 - 40%) time than an ATA configuration drive. Note that "Low level format" fixes all difficult logical damage.
    (4) Put the fixed disk back in your computer's drive bay. Re-configure the jumper pin setting to MASTER before you place it into the drive bay of your computer.
    (5) Restart from Mac OS X 10.3 Panther full install CD. Re-initialize and re-partition it to install Mac OS X 10.3. Update to Mac OS X 10.3.7 via Software Update. Repair the disk permissions after each Mac OS X 10.3 installation and Mac OS X 10.3.7 update.
    Note that Panther's Disk Utility does not implement a "Low level format" option.
    Method 5:
    If Method 4 does not work or fix the damaged drive, let me know. You may need an advanced technique to fix it if the drive is physically not a problem.
    OPTION:
    Purchase a known good hard drive that conforms to your computer's ATA specification. Fix the damaged hard drive some other time. Nowadays, prices of hard drives are inexpensive.
    Mini 1.25, 512 AP/BT; 12 Al PB 1.5, 512 AP/BT   Mac OS X (10.3.8)   Wireless KB/Mouse, AEBS, 80 GB OWC FW HD

  • IMac late 2013 lost usb connection after efi smc update

    Hi
    Lately i purchased a late 2013 iMac with i7 and fusion drive.
    After i update to Mavericks and patched new efi and smc update,my mac start to lost usb connectiong when using, from keyboard mouse to my usb sound card, System is not freezing just the usb deviecs. have to press the power button to restart
    already tried reset NVRAM and PRAM but doesnt work.

    Exactely the Same issue with my iMac 27-fusionDrive3T late 2013, having USB HDs for time machine and data. I contacted the Apple support who propose first level  of support: resets SMC, hard reset and so one without success . I did several trials removing hubs, using different USB (3.0,2.0 and 1.0) and changing devices connections(direct to iMac or through USB hub). I succeeded to find a stable configuration puting audio USB speaker  directly connected to IMac. When I put this USB speaker through USB huband  launch itune music after a certain time all USB chain freeze, and by consequence no more possibility to control the iMac with keyboard, trackpad .... IMac is still working,!  The only possibility is to reboot the machine with tne reset button. Hope also this will fixe in the future OSX release!

  • No wireless connection after last Airport update

    My MB is no longer able to use Airport after update yesterday. Tried everything, like hard shut down, safe boot, new network in stalled,..... nothing helped!
    Please, if any other ideas.... HELP ME OUT!

    I have exactly the same issue and symptoms. I applied the update, rebooted, and landed in wireless limbo. Yes, if I remove encryption from my wireless router, the MacBook then works. Yes, my other Mac on my net (and my Linux and Windows boxes and my Nokia 770) all work just fine with the 128 bit WEP.
    Why doesn't Apple have a mechanism for rolling back patches, like I can do with Linux! Oh yes, testing would be good idea too.
    Question - has anybody tried entering the WEP key in HEX?
    Question2 - anybody have a "friend" inside Apple?
    I have been through a lot of postings and apparently this problem is a regression and crops up again and again in new versions/patches to MacOS.
    MacBook   Mac OS X (10.4.8)   1 GB RAM

  • Help - lost network connection after firmware upda...

    I just updated the software for my 5500, and while it isn't 'dead', it no longer picks up a signal (ie: no bars). I've tried two sim cards, and neither works. I've tried setting the network operator manually, but no luck there, either - it recognized the network once, but never after that. I'm using att in the virgin Islands, which worked perfectly before the update. Any hints?
    Thanks!

    I finally called Apple and reset the Airport. It's working again.
    Thanks, John. Yes, I could see my network in the Airport menulet, but the Airport couldn't see the internet. In the Airport Utility the DHCP address appeared correct, that is, assigned by my service provider. The router IP address was 10.0.1.1 and my laptop was 10.0.1.XXX.
    If I plugged the modem directly into my computer and renewed the DHCP license it would work. As soon as I moved it to the Airport and rebooted the Airport there was no internet access via Ethernet or WiFi. I tried rebooting everything at least a dozen times.
    I called Apple and reset the Airport with a paper clip. I had to re-enter all of my information, network name, password, etc. I got a configuration error the first time I hit "update" but after another reboot it worked. We also turned off my cable modem for at least five minutes.
    I wish I'd thought of resetting the Airport (instead of just rebooting).

  • Lost Internet connection with last SW update

    The software update on December 5th seems to have caused me to lose Internet connection on my S4. Nothing wrong with WiFi, my computer has connection no problem.

        imcat,
    I want to make sure that the device is up and running for you without any issues. Are you having issues with Wi-Fi internet connection or with the 4G LTE internet access on the phone? Please keep me posted.
    KevinR_VZW
    Follow us on Twitter @VZWSupport

  • Apple TV2 can't find my network connection after recent update?

    Why can't my Apple TV2 can't find my network connection after recent update?

    I had to update the software on my Airport Extreme then reset my apple tv and that resolved the issue for me.

  • Lost data connectivity after upgrading iPhone 4 to iOS 5. How to fix?

    Hello,
    I upgraded my 16GB iPhone 4 yesterday from iOS 4.3.5 to iOS 5 and everything went fine after a few failed connections to Apple's servers, however my phone lost the data connectivity completely. Phone and SMS worked fine, I could also connect through wi-fi with no problems, however whenever I tried to use data I got a message that my phone was not signed to an internet service.
    I restored my phone from the backup after upgrading. Not successful. I also reset the network configurations. No deal.
    My carrier is Vivo (Brazil) and everything worked fine prior to the upgrade (and after the downgrade).
    I imagine it can be a problem with APN configuration under iOS 5 and I tried to configure it through a webpage, but I got a message that my phone already had a APN config (profile) and could not install another. Under Settings>General>Network I don't have the "mobile network option" nor the "profile" option.
    Any thoughts? So far I haven't contacted other people under my carrier who upgraded to see if they had the same problem.
    Thanks for reading,
    Samuel

    I got a workaround; it's not what I wanted, but it solves the main problem.
    I noticed that I only lost data connectivity after restoring from backup after the iOS 5 update. So what I did was to backup my phone, restore again to iOS 5, configure as a new phone and backup again (with nothing in the phone).
    Then I launched an iPhone backup utility software, in this case, iBackupBot, which in the trial version is enough for what I wanted. I opened the old backup and exported only the files I wanted (like call history and SMS history), then I imported these files into the new backup and restored from it.
    I lost my media files (which I copied before) and some configurations, but the most important itens, like SMS, I managed to export from the old (complete) backup.
    Message was edited by: samuelsam

  • Lost network connection HELP HELP HELP

    hi there i have big problem and i see it in first time from 5 years the problem is i upgrade to ios8 and after i complete the last step when he ask me to chosse backup i select the last one and the last one isbefor just one dayfrom the software that mean the backup from IOS7 after it i wait to restoring setting for i cloud then its appear to me massage that i lost network connection
    and i tried more than 3 wifi connection and diffrent connection and the same problems
    please help i looked in google and in internet for this problem and i didnt see any solution and apple didnt give any solution for this just say u have to connect to good network and plug the phone to ac power and i do these things and the same problems
    Last back up in 17/9/2014
    backup without problems

    is there a problem with this link of mine...hv already done half of it now....wat do u say...
    or shud i stop it and try urs....
    http://appldnld.apple.com/iPhone4/041-9618.20111012.Zxb22/iPad2,1_5.0_9A334_Rest ore.ipsw

  • Airplay mirroring problem:when i change slide mirroring from off to on ,my new i pad lost wi fi connection and apple tv lost wifi connection:ihave last software for both.Can u help me?thanks

    when i change slide mirroring from off to on ,my new i pad lost wi fi connection and apple tv lost wifi connection:ihave last software for both.Can u help me?thanks.
    when i use i pad with apple tv for see my photo,youtube and movies all ok.

    I suspect that the problem is in your router. Do NOT consider your router to be blameless if some other devices seem to work with it.
    Try restarting your WiFi router by removing power for 30 seconds. Don't just turn it Off. On many routers that doesn't really do anything but put the router into standby mode. If that does not help check for a firmware update for your router. If none exists which corrects the problem consider replacing the router.
    There is a chance that some services turned on in your router could be causing problems. Look for a setting called QoS (Quality of Service). If ON turn it OFF.
    If you need more help please give the make, model, and version of your WiFi router and how you have it configured.
    See also here: http://www.apple.com/support/ipad/wifi/

  • Cannot access internet through itunes after last itunes update. Cannot get to itunes store or itunes help. Everything else works fine.

    After last itunes update I cannot get to the internet through itunes. Cannot get to itunes store, itunes help, etc. Also, now when I sync everything syncs properly but I get message at end that tells me that my phone cannot be backed up on the laptop.

    Something may be corrupt in your iTunes installation. The backup problem may or may not be related. The first step is reboot your system, disable your antivirus and firewall and try again. The next thing to try is completely removing iTunes and reinstalling: http://support.apple.com/kb/HT1925.
    Also, if you used TinyUmbrella or Recboot as unauthorized apps to help with the update they corrupted your network settings on your computer. You will have to edit your hosts file and remove all references to Apple servers.

Maybe you are looking for