Fault Code F1237
Hi,
After upgrading my UCS to version 2.1(3a), a fault appeared on one of the blade servers with a code of F1237
the full message is:
Health LED of server 1/2 shows error. Reason: P3V_BAT_SCALED:Voltage Threshold Crossed;
Type: equipment
Cause: health-led-amber
Code: F1237
any suggestion to resolve this fault as I tried to search for a solution with no success.
-Abdullah
Abdullah,
Welcome to the community!
That sensor makes reference to the CMOS battery on the server. Could you please open an SSH session to the UCSM virtual IP address and run the following commands in bold?
B# connect cimc X/Y X=Chassis Y=Blade
[ help ]# sensors
The output will look something like:
CIMC Debug Firmware Utility Shell [ support ]
[ help ]# sensors
Sensor Name | Reading | Unit | Status | LNR | LC
=================|===============|============= |=====|
P3V_BAT_SCALED | 3.102 | Volts | OK | 1.993 | 2.416 <<<<<<<<<
P1V5_DDR3_P1 | 1.329 | Volts | OK | 1.212 | 1.280
At the bottom you can see what column means:
LEGEND:
LNR: Lower Non Recoverable Threshold
LC : Lower Critical Threshold
LNC: Lower Non Critical Threshold
UNC: Upper Non Critical Threshold
UC : Upper Critical Threshold
UNR: Upper Non Recoverable Threshold
na : Not available at this time or not applicable
If you see your battery is not within the acceptable ranges, then open a TAC case to have the battery replaced cause that is the only way to solve that low voltage issue.
Rate ALL helpful answers.
-Kenny
Similar Messages
-
Latest IOS displays fault code 1671, what does this mean?
latest IOS displays fault code 1671, what does this mean?
If it has NEVER been jailbroke, here are some standard repair procedures:
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this. -
Error code: F1237. SASO_FAULT
I have received the following error code on one of our B200-M3 blades. There were no changes made to UCS about which I am aware. The LED on the front panel is green. I did not receive a "call home" notification. The error occurred several days ago. There are no known functionality issues. Google and Cisco Support searches were fruitless.
Description: Health LED of server #/# shows error. Reason: SASO_FAULT:Sensor Failure Asserted;
Type: equipment
Cause: health-led-amber
Code: F1237
Severity: Major
Does anyone have any insight as to the cause and remediation of this error?
Thank you. .. . . . ... .. . . . . . . .. .. ..Thank you for the response.
UCSM firmware version: 2.1(2a)
CIMC: 2.1(2a)
BIOS: S5500.2.1.1b.0.020620132148
RAID controller (LSI): Boot loader version: 06.34.00.00. Running version: 01.32.09.00
Actual blade module (mistake made in original post): B200-M2
Events on SEL on 12/2/13:
e9 | 12/02/2013 23:38:24 | System Mgmt Software | OS stop/shutdown #0x00 | OS Graceful shutdown | Asserted
ea | 12/02/2013 23:38:24 | OEM timestamped record: Type: DD: Mfg ID: 37 01 00:Raw SEL: EA 00 DD 50 6E 9D 52 37 01 00 00 FF 00 05 00 00
eb | 12/02/2013 23:38:29 | CIMC | Entity presence BIOS_POST_CMPLT #0x53 | Device Absent | Asserted
ec | 12/02/2013 23:40:33 | BIOS | System Event #0x83 | OEM System Boot Event | | Asserted
ed | 12/02/2013 23:40:34 | CIMC | Entity presence BIOS_POST_CMPLT #0x53 | Device Present | Asserted
ee | 12/02/2013 23:40:40 | CIMC | Drive slot(Bay) SAS1_FAULT #0x22 | Predictive Failure asserted | Asserted
ef | 12/02/2013 23:40:41 | CIMC | Platform alert LED_BLADE_STATUS #0x62 | LED color is amber | Asserted
f0 | 12/02/2013 23:40:41 | CIMC | Platform alert LED_SAS1_FAULT #0x65 | LED is on | Asserted
f1 | 12/02/2013 23:40:41 | CIMC | Drive slot(Bay) SAS0_FAULT #0x21 | Predictive Failure asserted | Asserted
f2 | 12/02/2013 23:40:41 | CIMC | Platform alert LED_SAS0_FAULT #0x64 | LED is on | Asserted
f3 | 12/02/2013 23:40:52 | CIMC | Drive slot(Bay) SAS1_FAULT #0x22 | Predictive Failure deasserted | Asserted
f4 | 12/02/2013 23:40:53 | CIMC | Platform alert LED_SAS1_FAULT #0x65 | LED is off | Asserted
f5 | 12/02/2013 23:40:53 | CIMC | Drive slot(Bay) SAS0_FAULT #0x21 | Predictive Failure deasserted | Asserted
f6 | 12/02/2013 23:40:53 | CIMC | Platform alert LED_BLADE_STATUS #0x62 | LED color is green | Asserted
f7 | 12/02/2013 23:40:54 | CIMC | Platform alert LED_SAS0_FAULT #0x64 | LED is off | Asserted
f8 | 12/02/2013 23:40:59 | System Mgmt Software | OS Boot #0x00 | C: boot completed | Asserted
f9 | 12/02/2013 23:40:59 | OEM timestamped record: Type: DC: Mfg ID: 37 01 00:Raw SEL: F9 00 DC EB 6E 9D 52 37 01 00 00 77 1A 9D 52 00
HDD status, Disk 1 (UCSM, Equipment tab> Inventory tab> Storage tab> Disks): States, Operability: Operable
Additional comments:
The "OS graceful shutdown" may have been related to a loss in SAN availability we experienced on 12/2/2013. The SEL events are essentially identical to earlier OS restarts. Identical events in the 12/2 restart are logged for SAS0 and SAS1.
The SAS0, Predictive Failure deasserted event leads me to believe that there is nothing wrong with the disk. This may be a "false positive."
What does this additional information lead you to believe?
Thanks again .... . .... . . ... . ... . . . . .. -
fault code 3194,when I update from 6.1.4 to 7.0.2.
<Email Edited By Host>Hi xsliu2013,
Thanks for visiting Apple Support Communities.
You may find the information in this article helpful:
iOS: Restore error 3194 or 'This device isn't eligible for the requested build'
http://support.apple.com/kb/ts4451
Best,
Jeremy -
I tried updating my iPhone with the latest update. It downloads the update to my computer fine, but when it tries to update the phone, I keep getting a fault code of 3014. I've tried it four times.
Try taking it to the nearest Apple Store. They should have computers there that they can use to get your iPhone out of recovery mode. Make an appointment first.
-
trying to get Itunes match, after payment I start and get fault code 4002, what now?
The 11222s can sometimes be associated with LSP issues.
I'd try the following document:
Apple software on Windows: May see performance issues and blank iTunes Store
(If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.) -
Power on password fault code 97025088
Need your help guys. Have this fault code and can't log in. Kids put a dang password on it.
This question was solved.
View Solution.Try >> 28983008
Enter BIOS and disable password. Use the code as old password leave new blank. Save & Exit.
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
Access to fault code history from CWIS
It would be nice to have the ability to pull fault history from CWIS while logged in as admin, rather than having to get in front of the user interface. We have 43 Xerox machines company wide spread across 6 buildings, and up to 10-15 miles apart. While 50% of our machines have Remote User Interface, other machines have no received upgrade or unable to support the feature. Thank you.
The machines we use are primarily the colorqube 9300 series. We also have a few 8700's and 8900's and a lone 7835. Even with the most recent software updates you cannot pull fault code history from CWIS. I appreciate your response. Thank you,
-
i put my iphone to recover and after a while din just nothing. i tried again and it gives fault code 4014. i used several times de recovery without any results. phone is just dead. i can not start it. lights off. i can not acces it.
iOS: Restore errors 4005, 4013, and 4014
-
Hi ,
Flex doesnt identify fault code received through web services as the responce code is greater than 200.
Is there any way to receive this fault code.
Cheers!:)Hey @richmcconn2014 ,
Welcome to the HP Forums!
I understand you're getting errors on your Omni 10 tablet regarding the wireless adapter.
I'm unable to find any information on a hardware error "fault code 103."
Can you please elaborate on these errors?
Where do you see the error? (Device Manager, bottom right corner by the wireless icon, when trying to browse, on startup?)
Have you made any recent changes to the tablet? (Windows updates, driver updates, software installations, or security software updates/installations?)
Do you have the same issue on a different wireless network?
What have you attempted to resolve the issue so far?
Thanks! I look forward to hearing back from you.
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP. -
When I try to install the new 5.0 software, I get fault code 14.....then my phone no longer works. What do I do????
Covered here:
http://support.apple.com/kb/TS3694 -
what is this fault code and how can i fix it ?
Read here:
http://support.apple.com/kb/TS3297
Especially specific conditions & removing the SC folder. -
What is fault code -42110?
Read here:
http://support.apple.com/kb/TS3297
Especially specific conditions & removing the SC folder. -
Setting SOAPFaultExcepion fault codes and fault detail
I'm using WLS 7 SP1.
I'm having a couple of problems with SOAPFaultExceptions in WLS 7 SP1.
i) The generated web service front end happily wraps SOAP Fault fault string with
"EJB exception..." and always reports the fault code as "Server"; I believe the
latter problem is is a known issue.
ii) In an effort to get around the above problems, I thought I would simply add
detail entries but to be honest I can't quite figure out how to do it. I thought
I would create a Detail container via a SOAPFactory and add a detail entry via
Detail addEntry().
Am I able to do this with WLS 7 SP1 as is or do I need to use additional SOAP
libraries (pointers would be appreciated)?
Thanks.In your orchestration, capture the SOAPFault (hope you're already doing this), then in the captured message if you use the XPATH as below, it will capture the ErrorCode and ErrorText from the above shown fault structure.
sErrorCode = xpath(msgYourSOAFFault,"string(/*[local-name()='Envelope' and namespace-uri()='http://schemas.xmlsoap.org/soap/envelope/']/*[local-name()='Body' and namespace-uri()='http://schemas.xmlsoap.org/soap/envelope/']/*[local-name()='Fault' and namespace-uri()='http://schemas.xmlsoap.org/soap/envelope/']/*[local-name()='detail' and namespace-uri()='']/*[local-name()='errorDetail' and namespace-uri()='http://integration.com/ErrorDetails.xsd']/*[local-name()='Error' and namespace-uri()='http://integration.com/ErrorDetails.xsd']/*[local-name()='ErrorCode' and namespace-uri()='http://integration.com/ErrorDetails.xsd'])");
//ErrorText
sErrorText = xpath(msgYourSOAFFault,"string(/*[local-name()='Envelope' and namespace-uri()='http://schemas.xmlsoap.org/soap/envelope/']/*[local-name()='Body' and namespace-uri()='http://schemas.xmlsoap.org/soap/envelope/']/*[local-name()='Fault' and namespace-uri()='http://schemas.xmlsoap.org/soap/envelope/']/*[local-name()='detail' and namespace-uri()='']/*[local-name()='errorDetail' and namespace-uri()='http://integration.com/ErrorDetails.xsd']/*[local-name()='Error' and namespace-uri()='http://integration.com/ErrorDetails.xsd']/*[local-name()='ErrorCode' and namespace-uri()='http://integration.com/ErrorDetails.xsd'])");
For adding the exception handler for SOAP-Fault, you can either refer the sample in SDK or
reference this article. And in the exception handler, use the above XPath to capture the ErrorCode and ErrorText.
If this answers your question please mark it accordingly. If this post is helpful, please vote as helpful by clicking the upward arrow mark next to my reply. -
Hello, I have a problem using Labview 6.1. When attempting to run the software I am encountering a fault with code LPP 556. Any ideas or suggestions would be extremely welcome, Pete
Can you give us more information. Screen captures, saved in a format other than ".bmp", such as .jpg would be helpful. I don't recognize the error, but then it has been a while since I did anything in 6.x Are you trying to run any other code with it, like special hardware drivers, .dll's, etc.?
Putnam
Certified LabVIEW Developer
Senior Test Engineer
Currently using LV 6.1-LabVIEW 2012, RT8.5
LabVIEW Champion
Maybe you are looking for
-
Is the Apple Digital AV Adapter and the Apple VGA Adapter the same thing
is the Apple Digital AV Adapter and the Apple VGA Adapter the same thing i want to get a ipad and i want to no if there the same thing before i buy it i would want it for the web for pic but for videos too
-
We are running IE8 as a RemoteApp on Windows Server 2008 R2 Remote Desktop Services "Terminal Server". It has Reader X installed. When opening linked PDF document, it shows the protected mode "fail" dialog. If, instead, explorer.exe is launched as re
-
Trying to unhide and hide app purchases via itunes on iOS 6.1.3
I am trying to unhide and hide apps on itunes from my apple account. I do the process to unhide and hide them and itlooks like it worked but then when i go back to the purchased page of the app store, nothing happened. WHAT DO I DO!?!?!?!?
-
Adding Unknown computers resources by direct membership rule issue
Hi, everybody! Finally, i've got issue discrabed here http://blog.coretech.dk/kea/collections-not-being-refreshed-in-configmgr-2012-r2/ In situation with large count of primary sites and unknown computers accounts (two for each site certainly), it's
-
Lastest version Flash Player Issue
I installed the latest version for Mac and when I go onto the internet, I tried Safari, Firefox, Chrome, and IE for mac, It keeps telling me I have to install the latest version to view page. My OS is mac 10.5.8. Is there something new I need to do t