Favorite channel guide not available

My favorite channel guide not available on two TV sets.I have unplugged the power from the box w/o any luck. This has been occuring for several weeks. Please help.

This is usually a communication issue back to the X1 servers...  if you would like some help from the users of the forums, can you post your Upstream Power Level, your SNR and your downstream power levels for others gto see and comment on?    You undoubtedly may need a TECH onsite to clean up your signals, but posting those levels here can confirm this.

Similar Messages

  • Channel Guide not Full Screen

    Since the new update for the FIOS cable box, the channel guide will not fill the screen. I did some research and found that it is because I have one of the older models of cable boxes.
    I called Verizon and the supprt tech told me that I could order a replacement but there was no guarantee it would be one of the newer models as they cannot specify the model.
    I was directed to the Verizon site where I could request a high capacity DVR but there is a wait list and it would cost $40.00.
    Does anyone know how I can get a newer model without a fee or is that going to be a given?
    Thanks in advance.

    Go to one of their stores is the most relibale.
    Otherwise play pot luck on asking for a replacement.  Tell them you need one that supports adding a external disk, and you might have better luck getting a 7216 or 7232, since the 6416 does not support esata which is needed for an external drive.

  • FIOS local channels SD not available - 20147

    Is anybody else finding that their local SD channels (below say channel 10) are not available yet their corresponding HD ones are fine?

    I responded to your identical post at http://forums.verizon.com/t5/FiOS-TV-Programming/Local-Weather-Channel-Not-Available-on-SD-STB/m-p/4... 
    Anthony_VZ
    **If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
    Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

  • CityExplorer (Guides) not available in Nokia Maps ...

    Hi,
    I upgraded my N95 to Nokia Maps 3.0.
    Downloaded the latest Nokia Map Loader (3.0). But there I can't download any Services as in the old Map Loader.
    There are no Global guides from Lonely Planet, Michelin, and WCities possible to download, as described in on the Nokia Maps homepage.
    CityExplorer Services
    I have purchased a 2 years licens for CityExplorer. But anyway, it's not possible to download with Noka Map Loader 3.0.
    Downloaded Nokia Map Loader 2.0.2 instead, there the folder "Services" is still available. But when I click on that, it always tells me:
    Connection to the map server has been interruped. Make sure your Internet connection is working and retry. If you are still unable to download, try again later." 

    All right. So with POI you mean for example the petrol stations, restaurants, or shopping centers near my position?
    I find them when I select "Explore" in the Map 3.0 menu.
    Also, when I click on "Show Detail" at my current possion, or at one of the POI's I can select, and I have the internet connection online at that moment, then I will see the actuall weather information for this place.
    The same when I click on the places I have saved under "Favorits". When I click on "show details", then I see the weather information about this point. (when Internet connection is on). - Nice!
    But anyway, I'm missing the "Lonely Planet & Michelin" guides. Also I haven't found the "WCities entertainment" yet, described in in the link I posted in my previous post. Maybe it's only available for a few cities.

  • LCCS Developer Guide not available in PDF format?

    When I click on the pdf link I get: You are not permitted to perform this operation.

    I click on the LiveCycle Collaboration Service developer guide link on
    http://www.adobe.com/devnet/flashplatform/services/collaboration.html
    That takes me to http://learn.adobe.com/wiki/display/lccs/LiveCycle+Collaboration+Service.
    I click on the PDF Version link there, and it takes me to http://learn.adobe.com/wiki/spaces/exportspace.action?key=lccs,
    which says "You are not permitted to perform this operation."

  • Smart Guides not available

    Why is the Smart Guides option grayed out in my View menu. I am unable to turn them on/off and all options are selected in the Preferences ➡︎ Guides & Pasteboard ➡︎ Smart Guides menu.

    Thank you for the valuable info on fixing my Smart Guides issue. Evidently I wasn't fast enough to press four keys while restarting ID, so I used the method for exposing hidden files, entered the Library, and changed the names of two ID files thereby replacing the preferences. Worked like a charm!

  • GUID not available in data service model

    In SAP CRM you use something called GUID as a unique key to identify entries in a table.
    A common scenario is where a user select one entry in table A and get corresponding entries from table B based on the first table selection.
    Now I’m trying to build a demo in Visual composer. The problem is that the GUID attribute is never displayed in the data service model after import. In webdynpro the GUID is a BINARY type and in the CRM the type is RAW.
    My question is:
    Why can’t I see the GUID in the data service model ?

    Its a custom one!
    Its a very simple fuction module that just shold return a table.
    -><b>Function module:</b>     List_files
    -><b>Export</b>
       Parameter Name:     ET_DATA
       Associated TYPE:     ZET_FILES_TABLE
       Pass value:     True
    -><b>Table type:</b>     ZET_FILES_TABLE
    -><b>Line type:</b>     ZET_FILE
    Initialization and Access:     Initial Line Number 0
    Access:     Standard Table
    Key definition:     standard key
    Key category:     Non-unique
    -><b>ZET_FILE</b>
          -><b>File_GUID</b>
             Component type     GUID     
             Data type: RAW
             Lentgth:     16
             Decimal:     0
    -><b>Data element GUID</b> - Globally Unique Identifier
    Package:     SOS_MAPPING

  • Many channels missing/not loading

    Many of my SD and HD are not loading or are missing. When I tune to the channel I get a blank screen which eventually kicks to a verizon service agent screen that "checks for blackouts" and then comes back to tell me the channel is not available. This is happening on too many channels to list. I've reset the box twice and worked through the online trouble shooting to no avail.
    Verizon, get this fixed before I cancel on you.

    hi, are you in calif? i am, and so far mine are all o.k.

  • I want to play an episode from channel seven but keep getting message not available in this region - but it is

    GOing bananas trying to play an episode from channel 7 in Perth. Tryed using Photon for flash and ads play but not main event. Get a message not available in your region.
    HOw can I catch up with my favorite programs? Tv station recommends I change my IP address but I don't know how to do that or to change it to what. Love some ideas. Thanks, Lou

    Thank you so much, Ram!  I REALLY APPRECIATE YOUR HELP!
    I am wondering if it possible to manually create a node in RSA6 for the InfoSet.  I tried it by doing the following:
    I went to RSA6 and clicked on the white icon for "Create Node".  I then entered the number "8", followed  by the name of the InfoSet.  (I entered an "8", because all our DataSources seem to start with an "8".  I'm not sure why.) 
    The DataSource now shows up, but when I double-click on it, nothing happens.  When I select it in the hierarchy and then click the icons for "Display" or "Change" or "Check", I just get an error message that says, "You have not selected any DataSources."
    Also, do you know where I can get my hands on the white paper? 
    Thanks again!
    Regards,
    Sarah-Jane

  • Communiocation channel: Value with name asmaBaseFileName not available

    Hi friends,
    After upgrade our Dev system to PI 7.1. Whne i try to start the communication channels  from Communication channel monitoring.
    I am getting error for all the channels as follows :
    Configuration error: Value with name asmaBaseFileName not available (Software version: 3.0.15)
    Kindly guide  me how to rectify this issue.
    Renu

    After upgrade our Dev system to PI 7.1. Whne i try to start the communication channels from Communication channel
    monitoring.
    Which metadata are the channels using...SAP PI7.0 or SAP PI7.1? If you dont import the metadata of SAP PI7.0 in the PI7.1 system then you may get an error for the communication channels....you should either change the channels to point to PI7.1 or import the metadata in ESR.
    @Kiran: The tpz reference you have given seem to be of SAP PI7.11 .... will it also work for SAP PI7.1
    Regards,
    Abhishek.

  • One TV keeps getting message this channel not available

    OK so one TV an older one, in my home keeps getting the message this channel not available.  I went through ll the trouble shooting steps.  My other two TVs are fine but they are new one's.  This is my grandpas' old one.

    I'm sure it happens to many channels from time to time, because that is what happens to me.  On the DVR or on the HD STB.  Tonight I sat down to watch the Yankees play the Phillies on ESPN.  My 2 favorite teams, very excited.  At first ESPN doesn't load, then I get the BSOD w/ the white letters in the middle of the screen telling me the channel is unavailable.  It provides me w/ 2 options.  Option 1 is to switch away from this channel and back again (didn't work).  Option 2 is to call the toll free number, input a code and everything will be fine. 
    So I called the toll free number, entered the codes as prompted, and listened to the robot lady while she reset my DVR.  She told me to look for the yellow light to the left of the display after the reset and if the yellow light wasn't there, to turn on the DVR using the power button on the DVR.  I did not see the yellow light, so I turned the power on as instructed by the robot lady.  However, still no yellow light.  The robot lady is only prompting me to say next, repeat the instructions for the #%&^*(*&%@!!!#%$^ yellow light, or say problem fixed.  When I took her up on her offer of more info, she simply repeated the thing about the yellow light.
    How about adding a prompt to her repertoire asking if the yellow light isn't there.... I guarantee this will be the most used prompt.
    Meanwhile, I am too experienced and sane to call for tech support, live chat is always unavailable, so I am left waiting for some verizon kool-aid-drinking "guru" to tell me my coax is bad in the forums.
    Good night.

  • I only want to show favorite channels all the time when I go to Guide. Hide others.

    Is there a way to only show Favorites? I don't want to have to select Favorites, and make it easy on the family to see a limited amount of channels. I can create favorites but i have to Select 'Show Favorites'. 
    Any ideas?
    Thanks in advance.

    Yes, you can.
    There is a feature called Flip By Favorites, which you'll find under the Favorite Channels menu in Settings. Once the Flip By Favorites option is enabled, the box will only show the channels you have added to the selected favorites list. Channels that you have not added will be permanently hidden from the guide; the only way to access those channels will be to input their channel numbers manually.

  • Sundance Channel-Advertised as available when it is not

    I just started with FIOS about a week ago. We now have FIOS TV Prime HD. The Sundance Channel was advertised in black in white in the channel guide as being available on Prime.   It is not. 
    We then ordered the Showtime-Starz Entertainment Pack.  The Verizon website clearly states that Sundance is available with this "Pack."  It is not.  Thus we've now ordered two TV services that are not as advertised. 
    Does Verizon see a problem here, or is being loose with the facts just part of the marketing strategy?
    (We tried to take this up with Customer Service both on chat and on the phone.  Talking to Verizon Customer Service is like talking to a wall.  It seems as if they have absolutely no authority to engage in a discussion.  Thus they repeat apparent pre-scripted replies repeatedly.  I find this very frustrating)

    I just started with FIOS about a week ago. We now have FIOS TV Prime HD. The Sundance Channel was advertised in black in white in the channel guide as being available on Prime.   It is not. 
    We then ordered the Showtime-Starz Entertainment Pack.  The Verizon website clearly states that Sundance is available with this "Pack."  It is not.  Thus we've now ordered two TV services that are not as advertised. 
    Does Verizon see a problem here, or is being loose with the facts just part of the marketing strategy?
    (We tried to take this up with Customer Service both on chat and on the phone.  Talking to Verizon Customer Service is like talking to a wall.  It seems as if they have absolutely no authority to engage in a discussion.  Thus they repeat apparent pre-scripted replies repeatedly.  I find this very frustrating)

  • Requested circuit/channel not available

    Hello,
    I have a problem with a PRI link. We have installed CCM 3.3(3) and a 3745 with a PRI link to the telco. The 3745 is configured as a MGCP gateway. When I try to initiate an outbound call, I get the following Q931 debug message:
    *Mar 1 01:47:14.967: ISDN Se3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0005
    Bearer Capability i = 0x8090A3
    Standard = CCITT
    Transer Capability = Speech
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA9839F
    Exclusive, Channel 31
    Calling Party Number i = 0x0081, 'XXXXXXX'
    Plan:Unknown, Type:Unknown
    Called Party Number i = 0x80, 'XXXXXXXXXX'
    Plan:Unknown, Type:Unknown
    *Mar 1 01:47:15.127: ISDN Se3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8005
    Cause i = 0x82AC - Requested circuit/channel not available
    When I try an inbound call I get a busy signal, and a similar debug message (if I use another router to initiate that ISDN call).
    This is the "show ISDN state" screen:
    ISDN Serial3/0:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
    Layer 1 Status:
    ACTIVE
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0xFFFF7FFF
    Number of L2 Discards = 1, L2 Session ID = 13
    So I presume there is nothing wrong with the signalization??
    I contacted the telco person, and he told be that he sees some kind of BLOCKING state on our side of the PRI link.
    Please help or give at least some guidelines what to try next!
    Thanks in advance...

    Haha, 11 years later this post save us on CUCM 8.6.2, disabled "Inhibit restarts at PRI initialization" Works Excellent on the E1 affected.
    THANKS A LOOOT.

  • TV Says Channel Not Available

    So My TV says channel not available and I called Verzion and they are not able to help me.  I pay almost $200 dollars a month for service and I get the run around.  I am about to cancel my service if someone doesnt call me back or send a tech out to find out why is it that I am calling twice in one month for the same issue.

    One of course is to make sure its a channel you are suppose to get.
    Complaining here is just complaining to your Peers.  YOu need to follow through with contacting Verizon support.  http://www22.verizon.com/content/contactus/

Maybe you are looking for