Fax and modem via Drop & Insert card (VWIC 2MFT-E1-DI)

Currently installing pair of 2610XM rtrs with Drop & Insert cards (VWIC 2MFT-E1-DI) between them.
At each side there is PABX connected via E1 to Drop&Inser card, and 2Mbs leased line between locations.
Configured 15 CH for data and 15 CH for voice.
Data works fine.
Voice services work fine as well, BUT!!!
- When trying to use analog modems between locations it’s not working
- When trying to send fax between locations, it’s hardly working (i.e. 1/10 success & even then copy is hardly readable).
All problems not present when I bypass routers and 2Mbs leased line with 120Ohm cable.
Any knowledge about similar problems?
Any tip for sorting this kind of problems, or this is “by default” behavior for such setup?

Thanks for tip, sorry for delay in reply (I was on leave).
re synchronization, it is properly synchronized (as you can see in output attached.
All other phone services/functions (standard voice calls, CallBack, CLIP etc.) and data transfer is working fine. If any problems with link sync I suppose there should be some problems with those as well.
rtr#sh controller e1 0/0
E1 0/0 is up.
Applique type is Channelized E1 - balanced
Description: Connecton to 2Mbs leased line
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20011015, FPGA: 11
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (530 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
! each Interval equals 900 Secs (15 min)
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 2:
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
! etc, etc. Data in Interval XX:

Similar Messages

  • Fax and Modem Over IP

    Is it successful and reliable to deploy the fax and modem over IP in production? Does it stable enough to replace the PSTN connection?
    Do delay and packet drops in the network affect so much for fax and modem traffic?
    How about to implement fax and modem over IP via microwave link?

    i have read in the article in the web. here is the link
    http://www.soft-switch.org/foip.html
    1) Can you comment about implementing POS modem over IP is not reliable and workable.
    2) What the fine tune need to do most to successfully deploy the POS over IP?
    3) We had using Linksys SPA2102 ATA for the POS machine to be connected to the CUCM. Is it recommended brand ATA for impementing the POS?
    4) What is your experience implementing the POS modem? To CUCM or any Media gateway or IP PABX?

  • Fax and Modem with UC560

    Dear All,
    I have a somewhat tricky configuration to make happen and hope you can help me.
    I have a UC560-BRI-K9 (located in Germany) that is connected via BRI/ISDN and also utilizes an external SIP-Trunk.
    The UC is shared by two related businesses and the Trunks are separated using COR-Lists.
    I am now tasked with making both Faxes and Modems work. Via the SIP-Trunk, I only need T.38 to work for inbound and outbound faxes; no problem here. On the BRI-Port however, it is quite a different story: Here, I need both Fax and Modem working. The modem functionality is required by a Power Generator to call for maintenance in case of failure (or be called on a designated number for preventive checks). Furthermore, there also is a Postage Meter that also requires outbound modem comms.
    Digging through the configuration documents, I see that the UC500-Series does not support Fax-passthrough and modem-passthrough to be enabled simultaneously as they are handled similarly.
    If anyone has come across a solution for my problem, please let me know.
    Thank you very much in advance!
    Best regards,
    Colin

    If you use BRI and the fax or modem is conneceted to a FXS port in the same router, you don't need to worry about anything. It will work fine without any configuration.

  • I am having some serious issues with firefox, i can't print anything because it is stuck on fax and I can't use any of the drop down menus on any site

    I am having some serious issues with firefox to the point of choosing another search engine. I can't print anything because it is stuck on fax and won't let me change it to my printer when i do try to select my printer it jumps right back to fax. The drop down menus do not work on any of the sites I go to. For example when purchasing clothes and you have to choose a size from a drop down menu I can't do it when I click on the drop down menu it doesn't work at all. I don't have a virus I ran my virus protector and no viruses are present. I don't have any suspicious issues going on with my computer so there has to be something in Firefox that is causing my issues. I tried internet explorer and I don't have any issues there. I hope you can help me because I love Firefox and would really like to continue to use it.

    Lots of issues there, main one getting fcpx going again, try deleting the preferences using the utility deveoped by these guys.
    http://www.digitalrebellion.com
    Try deleting your render files and re-rendering the project.
    Start with these and let us know how you go.
    Tony

  • I paid down a card to zero and my score dropped 18 points

    Hi and welcome! You need to keep balances low (1-9% util) on credit cards and other revolving credit. High outstanding debt can affect a score.  Too much use of credit shows you may need more that you can handle, not good. Not enough use of credit does not demonstrate that you can use credit responsibly, also not good. It is a balance - show you can manage that balance and you will be rewarded. All revolving accounts reporting a 0 balance results in a Fico score decrease. Read up, take it all in, there are many answers in the following post, after that if you need calrification and/or still have questions, ask away! http://ficoforums.myfico.com/t5/Understanding-FICO-Scoring/Credit-Scoring-101-START-HERE/m-p/8169

    tufa4311 wrote:
    Bostonia wrote:
    WOW!! i did not know that little trick, thats wy, my scores has been so slow in rising up, is becouse i paid in full before the statement cus off,and always reported 0 balance, also recently closed a CC account with zero balance, and my scores dropped a lots points, so from now one i willlet report some small balance Hooray!!! i have learned so much from this forum, and each time i log in i learn somenthingnew and beneficial for my financial life!! thank you all for the greatest financial advices!!! you guys are awesome!!! Yes, ensure that not only you let report 1-9%, but also important, only let ONE of your credit lines report anything at all. No matter how many credit lines you have, only let one report a balance of 1-9%. You can and should rinse and repeat for your other credit lines. One billing cycle let Credit Card A report, next cycle let credit card B report. This is unnecessary and needlessly complicates things as cards seldom all report at the same time. Just pick one card and allow it to be your "reporter". By switching cards each month you can end up with periods between the cards reporting dates where either both are reporting a balance or neither is reporting a balance. That causes your scores to bounce around. So, wait until your statement cuts - when the statement is cut is when the reporting is done to the credit agencies, then before your due date pay in FULL so as not to incur any interest. Then start on your next credit line. Remember, it's not that you never want to pay in full, it's that you do not want to pay in full BEFORE the credit card reports. If you wait past the due date then you will incur interst. Also, note, you can use as many cards as you like with as high balance as you like during the billing cycle as long as when the reporting gets done you only have one line reporting 1-9%. Reporting to the credit agencies is not done daily, just once per billing cycle. If you know when your statement cuts, and you can ask them, then you know when you need to clean things up with your balances before it cuts/reports. 

  • HT1311 I know this is a basic question, however, how do i change my pass word on itunes to stop my kids from automatically buying tunes from the I store... as my card details are already saved they just log in with their ipods and download via my account

    I know this is a basic question, however, how do i change my pass word on itunes to stop my kids from automatically buying tunes from the I store... as my card details are already saved they just log in with their ipods and download via my account

    http://support.apple.com/kb/HE36
    Regards.

  • After installing Mountain Lion on my 17" MBP G-RAID mini connected via Tempo SATA Edge ExpressCard34 is no longer recognized. I restored icon and access by removing 34 card and substituting FW800 for eSATA. Any fix for the higher speed connection? TIA

    After installing Mountain Lion on my 17" MBP G-RAID mini connected via Tempo SATA Edge ExpressCard34 is no longer recognized. I restored icon and access by removing 34 card and substituting FW800 for eSATA. Any fix for the higher speed connection? TIA

    Looks like the Silicon Image drivers were moved to the incompatible software folder during install/upgrade.
    Downloaded latest drivers, errored out of install claiming that the drivers were from an unknown author!!!
    Emailed their tech support this evening describing problem.

  • I just bought something via my debit card but since i set my payment menthod to none and now i cant set my payment information back ...Its declined my card how i can solve this problem thankyou

    I just bought something via my debit card but since i set my payment menthod to none and now i cant set my payment information back ...Its declined my card how i can solve this problem thankyou

    I think the problem lays with Last.fm. I had the same exact problem as you. In your processes screen, end the task "lastfmhelper.exe" Last.fm still scrobbles. The tracks don't skip, although I notice there is still a bit of a lag in the first part of the song - but if you can deal with that, no skipping. I think you will have to end that task everytime you boot up your computer, or uninstall last.fm completely until they fix it; it is a bug in their software, as opposed to iTunes.

  • HT2497 do I connect my airport express to my modem via the WAN port and then connect to my imac via ethernet cable?

    Do I connect my airport express to my modem via the WAN port and then connect from airport express to my imac with ethernet cable? Is that how you "hard wire" the connection? Because when I do that, I still can't get online. Thanks.

    What is the make & model of your modem?
    You pretty much stated the correct wiring. There should be an Ethernet cable connected between the modem and the WAN (circle of dots) port on the AirPort Express base station.
    Anytime you change networking hardware it is always a good idea to perform a complete power recycle of that hardware. Check out the following AirPort User Tip for details. Please post back your results.

  • I have bought an I pad Air 128 with cellular connection.I travel a lot and will need to insert various cellular providers sim cards in the countries i visit. Will these various sim cards work in the I pad Air or is the i pad locked?

    I have bought an I pad Air 128 with cellular connection.I travel a lot and will need to insert various cellular providers sim cards in the countries i visit. Will these various sim cards work in the I pad Air or is the i pad locked?

    Hello, no ice. 
    Thank you for visiting Apple Support Communities.
    As long as you purchase the GSM model and acquire a Nano-SIM card, you should be able to use your iPad abroad.  Here is some information about this process that you may find helpful.
    iPhone and iPad: Using cellular networks while in another country
    http://support.apple.com/kb/ht1807
    Cheers,
    Jason H.

  • I have connected my time capsule to motorola SG6580 modem via ethernet.  I have a wireless network on the motorola and a wireless network from the time capsule.  I get duplicate IPs error messages sometimes. How do I fix?

    I have connected my time capsule to motorola SG6580 modem via ethernet.  I have a wireless network on the motorola and a wireless network from the time capsule.  I get duplicate IPs error messages (no connection) sometimes when trying to connect devices to the wireless network. How do I fix? Sometimes devices cannot connect to the network because of conflicting IPs.  I look on the Motorola and every device has a unique IP assigned but occasionally a device has taken the IP of another device.  I have been writing down all the devices and the IPs they have been using.  It happens more with PCs than Macs, ipads or iPhones.

    If the Time Capsule is set up correctly in bridge mode, then it is the responsibility of the Motorola modem/router to provide the correct IP address assignments for all devices on the network.
    Check to insure that the Time Capsule is correctly set up to operate in bridge mode as follows:
    On your Mac, open AirPort Utility
    Finder > Applications > Utilities > AirPort Utility
    Click on the Time Capsule icon, then click Edit in the smaller window that appears
    Click the Network tab at the top of the next window
    Insure that the setting for Router Mode is configured to read "Off (Bridge Mode)"
    Once you have confirmed that the Time Capsule is configured correctly, everything else is the responsibility of the Motorola modem/router as far as network routing and IP address assignments for devices.
    If you continue to have IP address issues, then you should contact the Internet Service Provider (ISP) that provided the Motorola device to you and ask them to fix the issue.

  • How so I drag and drop a card from my email list into a group?

    Hi, when I try to drag and drop a card into a group folder it will not accept it. What am I doing wrong? Thank you.
    Jim

    Are trying to do this from an email message?

  • How to make a PDF embedded image append a report and send via fax electronically from MS SSRS 2012?

    How can I make a PDF embedded image append a SSRS 2012 report and send via fax all electronically?  Is this possible?
    Thanks in advance for your time!

    Hello,
    1. The report item Image can be used to display the image which  embedded in the report, stored in a database, stored on the report server, or stored elsewhere on the Web.
    For example, you can embedded the PDF image in the report and stored as text in the report definition.
    2.Reporting Services includes an e-mail delivery extension and a file share delivery extension which you can send report to user or group through e-mail or send the report to a shared location on your network.
    If you want to send the report to FAX, you may try to create a custom delivery extension depend on your faxing software.
    Reference:Implementing a Delivery Extension
    Regards,
    Fanny Liu
    Fanny Liu
    TechNet Community Support

  • I use to administrate my DSL modem via an ip-address. When I enter it into FF8 I am asked where to save the file. Why and how can I prevent FF8 from doing that?

    I use to administrate my DSL modem via an ip-address. When I enter it into FF8 I am asked where to save the file. Why and how can I prevent FF8 from doing that?
    And now anytime I am entering an ip-address I am asked if I want to download the file.

    It happens when the modem server doesn't send the file as text/html, but with another MIME type.<br />
    I tried the index.html addition in case the server might send that file as text/html.<br />
    If your DSL modem has a support website then you can try to ask there for advice about how to configure the modem server.

  • My Airport Extreme and iMac appear to have the same IP address as a result of installing a new ATT modem via direct ethernet connection. How can I reset the Airport IP without disturbing the iMac setting if the iMac can't reach the Airport?

    My provider's (ATT) modem recently went bad and though I usually use an Airport Extreme connection to the modem I had to start up their new modem via a direct ethernet connection from my computer to the modem. In trying to restart my Airport to modem via ethernet connection I was told that my computer IP and Airport ID are the same and so now my computer will not connect to the Airport. How can I best get out of this situation?

    Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Maybe you are looking for