Fax Detect help, PLEASE! :)

I'm looking to configure fax detect on the UC 520.
I can get listen-first to work for faxes only. After 9 seconds, or when I press any key...the call is disconnected.
If I confgure it for connect-first, the line just rings... never answers.
Config is attached.
PLEASE let me know what's missing ... I had this working a while back, and I don't remember what I needed to do.
I've also tried
app_fax_detect.2.1.2.2.tcl and
app_fax_detect.2.1.2.3.tcl
Same issue.
THANK YOU !!
Greg

Hey Gregory,
I was looking at your configuration and found that app is applied on FXO port. Can you please send me following from the UC520
show ver
show run
show flash
Also I would like you to enable following debugs and make a test call
debug voip ccap inout
debug voip vtsp all
debug vpm signal
debug voip application all
debug fax mta all
Please make sure that you are collecting the debugs on buffer and not on console.
Thanks,
Malick

Similar Messages

Hp laserjet 200 color mfp m276 nw not receiving faxes - help please?

Good morning,
I have run the fax test report and followed the trouble shooting information in the manual and still am not receiving faxes --- any suggestions to help get back on line? All the tests say PASS for active phone line, phone cord connected to correct port, telephone line current test, dial tone detected on telephone line -- my HP product has passed the fax test -- but I cannot get faxes. The fax service log is saying no fax detected... any suggestions -- we use this fax to receive lab reports.
Thank you very much for any suggestions.

Hi KathFallston,
I understand that you are unable to receive any faxes and everything passes on the fax test. I can
help you.
Check these settings for the fax:
Go to the wrench icon/fax setup menu/advanced setup/private receive/turn it off.
Go to the wrench icon/service /fax service/error correction/turn it off.
Go to the wrench icon/fax setup /advanced setup/fax speed/change it to medium.
Go to wrench icon/service menu/fax service/clear saved faxes.
If you are still having issues, then follow this document.
Cannot Send or Receive Faxes.
What type of connection do you have? (Analogue, DSL, Cable Modem)
Is there any voice mail set up?
Do you have distinctive ring set up on the line?
If you need further assistance, just let me know.
Have a great weekend!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Hi can anybody help please. I am having terrible problems trying to use my Nikon D7100 to tether. I have downloaded the latest Lightroom updates and also checked my firmware which is also the latest avaiable and still Lightroom wont detect my camera!

Hi can anybody help please. I am having terrible problems trying to use my Nikon D7100 to tether. I have downloaded the latest Lightroom updates and also checked my firmware which is also the latest avaiable and still Lightroom wont detect my camera!. When I use a friends Canon camera it works every time!

Hi Keith thanks for your reply I have Lightroom 5.7.1 64 bit and my Nikon's firmware is version 1.02

My ipod touch 3rd gen wont turn on or charge and laptop couldnt even detect it. no indication that its charging even in laptop no heat up at the back. how can i fix it? help please

my ipod touch 3rd gen wont turn on or charge,laptop doesnt even detect it. no indication that its charging even in laptop no heat up at the back. how can i fix it? it happened after i plugged it in a socket then shows not supported with this accessory....help please.........thanks

Try:
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Just got second hand iphone4s. Tried to connect to iTunes on laptop running windows 8.1. Does not detect iPhone, iPod or iPad. Can anyone help please?

Just got a second hand iPhone 4s and tried to connect to iTunes on laptop running windows 8.1 does not detect iPhone, iPad or iPod. Can any help please? iPhone is version 7.1 and running latest itunes

Hello HungryHoover,
It sounds like you are not able to see any iOS devices in iTunes on your PC. I recommend the following article to help you troubleshoot that named:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
Thank you for using Apple Support Communities.
Regards,
Sterling

I Need Help for the popup message every time I go to safari: "Warning! Old version of Adobe Flash Player detected. Please download new version."???

I Need Help for the popup message every time I go to safari: "Warning! Old version of Adobe Flash Player detected. Please download new version."???

If you are talking about Safari on the iPad, there is no version of Adobe Flash for iOS and there never has been. Clear Safari, close the app and reset the iPad.
Go to Settings>Safari>Clear History and Website Data
In order to close apps, you have to drag the app up from the multitasking display. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the app that you want to close and then swipe "up" on the app preview thumbnail to close it.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
If you are talking about Safari on your Mac, you are in the wrong forum. But I would still clear the cache, quit Safari and restart the Mac.

HT201263 While updating Iphone 4 to latest on phone itself it got frozed and now apple sign is coming up after every 10-15 secs , even itunes is not able to detect phone, please help

While updating Iphone 4 to latest on phone itself it got frozed and now apple sign is coming up after every 10-15 secs , even itunes is not able to detect phone, please help

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work.

K60xi fax HELP PLEASE

MOVED TO A NEW LOCATION .... phone to fax rings once then dies .... can't receive faxes

Hey Gregory,
I was looking at your configuration and found that app is applied on FXO port. Can you please send me following from the UC520
show ver
show run
show flash
Also I would like you to enable following debugs and make a test call
debug voip ccap inout
debug voip vtsp all
debug vpm signal
debug voip application all
debug fax mta all
Please make sure that you are collecting the debugs on buffer and not on console.
Thanks,
Malick

No Fax Detected

My fax keeps printing a No fax detected report several times a day. I have read that I need to go into advanced setting and turn off private fax but I do not have that option.

Hello there! Welcome to the forums @thegoodwins ,
I read about the fax report printing out for you and not being able to turn off this option. Please let me know which printer model you have and I will check out the options for you!
How Do I Find My Model Number?
Best wishes,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

No fax detected CM2320 MFP

I keep a NO FAX DETECTED on my HP CM2320 MFP series printer. everything was fine 2 days ago. I canot receive any faxes.
Thanks
Laureen

Hello there! Welcome to the forums @thegoodwins ,
I read about the fax report printing out for you and not being able to turn off this option. Please let me know which printer model you have and I will check out the options for you!
How Do I Find My Model Number?
Best wishes,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

HP MFP M177fw - no fax detected

Hi,
I do have an HP MFP M177fw and i have a problem receiving fax message. It's always saying that "No Fax Detected". I tested this and it worked on a specific sender but for other fax sender it has always been a problem. Is there a proper setting for this? My HP printer has no telephone device or handset connected to it.

Welcome to the HP Forums tech21,
I see by your post that you are having issues receiving faxes.
I can help you with this issue.
I have provided a document to go through the steps to see if it will help resolve this issue.
Cannot Send or Receive Faxes.
Run the fax test and update the printer's firmware.
In the section for Faxes are sending slowly: Turn off the error correction. Set the speed to medium.
Please provide in detail the results if you are still having issues so I can assist you better.
What were the results of the fax test?
What type of connection do you have? (Analogue, DSL, Cable Modem)
Are you using the 2 wire phone cable?
Do you have distinctive ring set up on the line?
Is there any voice mail set up?
Where is the fax cable connected to? (modem, wall jack)
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

LaserJet M1319F MFP no fax detected

LaserJet M1319F MFP no fax detected
My Fax/Printer rings when a fax is coming in but it doesn't answer. It eventually says no printer detected. What am I missing??
Thanks

Hi @Biker542,
I understand that you are getting the message "no fax detected". I can help you with this today.
Make sure you are using a 2 wire fax cable.
If you connect a phone to the phone outlet on the wall, do you get a dial tone?
Can you send a fax?
I have provided a couple of documents with some steps to try to see if that will resolve the issue.
Troubleshooting Fax Issues.
Unable to Receive Faxes.
Sorry for all the questions, but it will help to resolve this issue quicker.
What type of connection do you have? (Analogue, DSL, Cable Modem)
Are you using the 2 wire fax cable?
Do you have distinctive ring set up on the line?
Is there any voice mail set up?
Do you have a answering machine? (Where is it connected to?)
Where is the fax cable connected to? (modem, wall jack)
Is there a phone also connected the printer?
Please provide in detail the results if you are still having issues.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Fax detect settings mx459

Hi, has anyone else had issue with fax detect settings on these units? I set it up to automatically detect which it will do, unfortunately it also squeals upon every single call you take about ten seconds into it....I either can bear with that or disable it to manual in which i miss all the faxes i get unless i notice them coming in....I also have an answering machine on this phone line just for more info. Anyone have any luck getting it set up to receive without the annoyances while talking on normal calls? Tried every different combination of setting on the device, followed the instructions in the manual and it still does the squealing when i take calls unless i put it on manual reception...

Hello mansfileddairy,
Setting the User-Friendly RX setting of the printer to ON may resolve the issue you are experiencing. To do this, please follow these steps:
Make sure that the machine is turned on.
Press the FAX button. The Fax standby screen is displayed.
Press the Menu button. The FAX menu screen is displayed.
Use the  button to select Receive mode set, then press the OK button.
Use the  button to select the TEL PRIORITY receive mode, then press the OK button. The confirmation screen asking whether to make advanced settings is displayed.
Use the  button to select Yes, then press the OK button.
Use the  button to select USER FRIENDLY RX, then press the OK button.
Use the  button to specify the ON setting, then press the OK button. The LCD returns to the Fax standby screen after you finish specifying all settings.
Hope this helps!
This didn't answer your question or issue? Find more help at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Hi all! I was updating the software on i pad to ios6, update was interrupted(apple update server is unavailable...). iTunes Diagnostics shows that "secure link to I tunes store failed". I use Windows 7 Home Premium 64 bit. Can anybody help please?

Hi all! I was updating the software on i pad to ios6, update was interrupted(apple update server is unavailable...). iTunes Diagnostics shows that "secure link to I tunes store failed". I use Windows 7 Home Premium 64 bit. Can anybody help please?
The following was done so far:
1. Windows Firewall - new rule created for itunes.
2. iTunes - latest version installed.
3. LAN setting : automatic detection of proxy is enabled;
4. iTunes diagnostics shows:
Microsoft Windows 7 x64 Home Premium Edition (Build 7600)
TOSHIBA Satellite L655
iTunes 11.0.2.26
QuickTime 7.7.3
FairPlay 2.3.31
Apple Application Support 2.3.3
iPod Updater Library 10.0d2
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 6.1.0.13
Apple Mobile Device Driver 1.64.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 003FB880034B7720
Current user is not an administrator.
The current local date and time is 2013-04-23 11:01:14.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
Intel Corporation, Intel(R) HD Graphics
**** External Plug-ins Information ****
No external plug-ins installed.
iPodService 11.0.2.26 (x64) is currently running.
iTunesHelper 11.0.2.26 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name:          {1CB5BBC2-8124-4664-899A-CE0A4683E3B4}
Description:          Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC
IP Address:          0.0.0.0
Subnet Mask:          0.0.0.0
Default Gateway:          0.0.0.0
DHCP Enabled:          Yes
DHCP Server:
Lease Obtained:          Thu Jan 01 08:00:00 1970
Lease Expires:          Thu Jan 01 08:00:00 1970
DNS Servers:
Adapter Name:          {8140112A-43D0-41D6-8B36-BE146C811173}
Description:          Atheros AR8152/8158 PCI-E Fast Ethernet Controller (NDIS 6.20)
IP Address:          10.5.7.196
Subnet Mask:          255.255.0.0
Default Gateway:          10.5.0.1
DHCP Enabled:          Yes
DHCP Server:          172.18.255.2
Lease Obtained:          Tue Apr 23 10:14:40 2013
Lease Expires:          Tue Apr 23 22:14:40 2013
DNS Servers:          121.97.59.7
                    121.97.59.2
                    121.97.59.3
Active Connection:          LAN Connection
Connected:          Yes
Online:                    Yes
Using Modem:          No
Using LAN:          Yes
Using Proxy:          No
Firewall Information
Windows Firewall is on.
iTunes is NOT enabled in Windows Firewall.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was unsuccessful.
The network connection timed out.
Connection attempt to purchasing from iTunes Store was successful.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was unsuccessful.
The network connection timed out.
Connection attempt to Gracenote server was successful.
The network connection timed out.
Last successful iTunes Store access was 2013-03-22 10:05:31.
@@@. iTunes IS ENABLED THROUGH THE FIREWALL , even though diagnostics says "NOT enabled"

hours after the first post i somehow got this to work. dont know how, but i do tried the dns clear cache, the clear host file, oh and i did the check automatically detech dns AND THEN se-check it again before i got this to work.

Brand new Mac user help please! How do you connect a 17" monitor to the MacBook? I have the monitor plugged into the Mac, but the F8 that I am used to with PC does not work. Please help. Thanks.

Brand new Mac user help please! How do you connect a 17" monitor to the MacBook? I have the monitor plugged into the Mac, but the F8 that I am used to with PC does not work. Please help. I am getting lots of spelling errors as the MacBook laptop screen is too small. Thank you so much! .

Contentmom6 wrote:
Brand new Mac user help please! How do you connect a 17" monitor to the MacBook? I have the monitor plugged into the Mac, but the F8 that I am used to with PC does not work.
Normally, you just connect the monitor to the MacBook using a VGA adaptor that you can buy from an Apple Store. Now try System Preferences > Displays > Detect Displays. You should now be able to select a display mode for the monitor. If it still doesn't work, then I'd check that everything is properly connected. I've had problems with colours disappearing due to a faulty connection in the VGA adaptor.
Bob

Fax Detect help, PLEASE! :)

Similar Messages

Maybe you are looking for