FAX Detection Application for a MGCP Gateway

Hi,
I have an MGCP Gateway and a Right Fax Solution along with CUCM. Was wondering if FAX detection application can be configured for this setup or is FAX detection only for H323 gateways.
Thanks
Prakash

It uses TCL script, so it is not available with MGCP.
Chris

Similar Messages

Configuring BRI interface for Voice ( MGCP gateway

hi there,
i have a Call Manager which is connect to Cisco 2800 series acting as MGCP getway. ISDN connection between the 2800 and the carrier ( telestra sydney ). the call manager is seeing the gateway and i have configured a numbering plan on the call manager for the phones. the phones can call internally but externally i dont what configuration i should configure under the BRI interface for the carrier ( telestra ) to recongnise my number plan. please if you have any demo configuration or configuration that has perviously used post to me.

this is a basic MGCP config on the Gateway on your area
BRI Switchtype Information
BRIs in Australia require no service profile identifiers (SPIDs).
There are two ISDN switch-types that can be used:
basic-net3?Currently the most commonly used.
basic-ts013?For older ISDN switches such as MicroLink.
isdn switch-type basic-net3 or 5
voice-card 2
dspfarm
dsp services dspfarm
controller T1 2/0
description T1 link to SRST
framing esf !--- Automatic method automatically adds
clock source internal
linecode b8zs !--- Automatic method automatically adds
cablelength short 133
pri-group timeslots 1-2,24 service mgcp !--- Automatic method
!--- automatically adds 24 channels.
!---You can manually edit channels.
description T1 link to SRST
interface Serial2/0:23
no ip address
isdn switch-type primary-ni !--- Automatic method automatically adds
isdn protocol-emulate network !--- Simulated Lab ISDN
isdn bind-l3 ccm-manager !--- Allows all Q931 to be backhauled over TCP to
!--- CallManager; automatic method automatically adds
no cdp enable !--- Automatic method automatically adds
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 171.69.103.225
ccm-manager config !--- Enables automatic config download from CallManager
!--- Automatic method automatically adds these commands
mgcp
mgcp call-agent 171.69.103.225 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp profile default

MGCP Gateways and Cisco Fax

We are considering adding a fax solution to our IPT infrastructure using Cisco Fax (Captaris RightFax). Ideally we would like the same voice gateways to terminate the fax calls (internal voice calls use QSIG and external calls use Q.931). Can this be achieved with MGCP-controlled Voice gateways? Can T.38 fax be configured with an MGCP gateway. I have seen examples where H.323 dial-peers are required to talk SIP to the Fax Server.
If not, is an alternative to use a back-to-back PRI connection between a voice gateway port and the Fax Server ISDN card, with appropriate route patterns in CallManager to route the fax calls to Fax Server, using Cisco Fax Relay?

with cm 4.2.3 there is mgcp t.38 support implemented.
see release notes cm 4.2.3
http://www.cisco.com/application/pdf/en/us/guest/products/ps6729/c1178/ccmigration_09186a0080724724.pdf
regards
mehmet

Can I use TNSI Payment gateway in iOS application for making product purchases of Pizza for one of our major client.

Hello Sir/Madam,
I am representing my company to ask this quest, your quick response is much appreicated.
We are making an application for one of our client for Pizza and food product purchased and advertisements. We are trying to implement a payment gateway so users can make purchases using their credit cards. Our client have used TNSI payment gateway on website however we are not sure whether we can use the same TNSI payment service in iOS Application.
Would you please confirm with us whether apple have an approval for using this Gateway service inside the app. Please let us know ASAP so we can make the integration for completing the app.
Also it would be real great if we are suggested some approved and valid payment gateways apple have approved for the apps submitted over appstore as this would help us to use the same services firmly wihtout the appstore rejection issue.
Link for gateway service provider : http://www.tnsi.com/products-services/payments/payment-services/secure-managed-p ayment-solutions/tns-payment-gateways
Thanks for you kind reply in advance.
Regards,
Vicky Dhas
Solutions Architect | Nano Equipment Pte Ltd.

What is the appstore rejection issue? It is best not to pay too much attention to what you read on internet media outlets as they are typically full of lies.
Food is the easy part. You cannot use Apple's payment systems for physical products. You must do that yourself using whatever system you have. Advertising is trickier. You talked about pizza and food and then slipped in that little tidbit. Why?
The bottom line is that the only people who get their apps rejected are people trying to scam either Apple or Apple's users. Sadly, not enough of them get rejected. You know if you are trying to scam someone or not. If so, then your chances of rejection are higher. When in doubt, consult Apple's In-App Purchase guidelines.

Fax Detect help, PLEASE! :)

I'm looking to configure fax detect on the UC 520.
I can get listen-first to work for faxes only. After 9 seconds, or when I press any key...the call is disconnected.
If I confgure it for connect-first, the line just rings... never answers.
Config is attached.
PLEASE let me know what's missing ... I had this working a while back, and I don't remember what I needed to do.
I've also tried
app_fax_detect.2.1.2.2.tcl and
app_fax_detect.2.1.2.3.tcl
Same issue.
THANK YOU !!
Greg

Hey Gregory,
I was looking at your configuration and found that app is applied on FXO port. Can you please send me following from the UC520
show ver
show run
show flash
Also I would like you to enable following debugs and make a test call
debug voip ccap inout
debug voip vtsp all
debug vpm signal
debug voip application all
debug fax mta all
Please make sure that you are collecting the debugs on buffer and not on console.
Thanks,
Malick

Cannot register MGCP gateway to CCM 4.1

Hello,
   I am running an application which simulates a MGCP gateway vs. a real CCM 4.1. I am not able to register the endpoints as you can see from the snapshot attached. I guess the problems lies in the 200 response to the following AUEP:
AUEP 89 AALN/S0/SU0/[email protected] MGCP 0.1
F: X+SRTP/A
200 89 OK
X: 2
L: p:20, a:PCMU, b:64, e:ON, s:ON
    I have also attached the trace file and CCM logs.
   I have 2 questions on this matter:
what is the correct format of the 200 message which needs to be sent to AUEP with SRTP?
how can I configure CCM not to sent this AUEP with SRTP(I have a similar one in my setup which is not sending this AUEP)?
Thanks in advanced for you support,
Ionut

Restrictions for Cisco Multiservice IP-to-IP Gateway Configuration:
Restrictions for SIP-to-SIP Call Signaling:
Transcoding is not supported.
SIP-to-H.323 Call-Signaling Features:
Codec transcoding (G.711-G.729) - supported
other:Transcoding is not supported on the Cisco 7200 and the Cisco 7301
copied from:cisco Multiservice IP-to-IP Gateway
http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_guide_book09186a0080409b6d.html
I have not found a solution, but i'd be interested in what you find though.

SRST with T1 CAS MGCP Gateway

Hello - we are trying to configure SRST on our T1 CAS MGCP gateway. We have been informed by a Cisco engineer that we cannot use SRST on a T1 CAS MGCP gateway and that the gateway must first be reconfigured as an H.323 gateway in order to implement SRST. Router is version 12.2(15)T14 and CCM 4.1 Any comments would be truly appreciated...thank you.

SRST doesn't support MGCP but does support MGCP to H.323 failback. You can still configure your router/CCM with MGCP then use the fallback commands for MGCP.
Looking at the SRST 4.0 system guide, page 42, T1 CAS is supported. With your version of IOS you would be running SRST 2.1, this is also supported.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/srst21/srstv21.pdf
http://www.cisco.com/univercd/cc/td/doc/product/voice/srst/srst40/srst40ad/s40sa.pdf
The ccm-manager fallback-mgcp command was added in IOS 12.2(11)T so it should be in your version. This is what you would need to do MGCP fallback to your H323 along with the call application alternate default.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tvr/vrht_c4.htm#wp1061367
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tvr/vrht_c1.htm#wp1670149
I would say it might be possible as I don't see anything saying no. Though remember MGCP fallback to H323 over SRST doesn't have call preservation.
Lastly here is a document on the SRST MGCP/H323 fallback.
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a008012ecc6.shtml
Please rate any helpful posts
Thanks
Fred

CUCM 9 & AS5850, Using MGCP Gateways not found in "Gateway Type" list...

I have an application where I need to control a large, AS5850 gateway using MGCP. CUCM version is 9.1, soon to be 10.0. The gateway is populated with CT3 cards.
We have confirmed that the AS5850 does in fact support MGCP, however it is not listed as an option in the list of gateway product choices when adding a new gateway in CUCM. So my first question:
1) How do you add an MGCP gateway in CUCM when it is not listed in the "gateway type" drop-down list? It seems there must be a way to do this. Other well known gateways such as the AS5300, AS5400 etc.. are also notably absent from the list of gateway choices. Perhaps there is a template that can be edited?
If anyone has experience utilizing an AS5850 gateway with CUCM & MGCP, it would be very useful to see sample configuration programming from your gateway.
Many thanks

Hi,
As per the datasheet, the Cisco AS5850 Universal Gateway supports H.323, SIP, and MGCP call-control protocols with extensive SNMP management and debugging capabilities. It works with the Cisco PGW 2200 Softswitch, the Cisco BTS 10200 Softswitch, and many partner softswitches as well.
http://www.cisco.com/en/US/prod/collateral/iad/ps509/ps512/product_data_sheet09186a008007cc48.html
It looks like that its not supported with CUCM.
HTH
Manish

[New_Feature_Requirement] [iOS 8] Detecting permissions for camera access

Here is the feature request: Feature#3837401 - [New_Feature_Requirement] [iOS 8] Detecting permissions for camera access
Problem: The camera privacy control is now required by iOS 8 for all regions. With iOS 8 any application that use camera encountered with a dialog asking for permission.
http://useyourloaf.com/blog/2014/07/16/ios-8-camera-privacy-settings.html
But we cannot detect permission for camera access by AIR.
StatusEvent event not firing by AIR: "Note: This event is not dispatched on the AIR platform. It is used only in Flash Player."
Camera - Adobe ActionScript® 3 (AS3 ) API Reference
So, if user don't allow use camera our application even cannot detect that. It could make application useless. Also it could cause problems with our applications in AppStore.
Please consider to provide some way to handle camera access. It could be StatusEvent like with Flash Player.

"Do Not Put iOS8 on an iPhone 4S"
http://gizmodo.com/dont-put-ios-8-on-your-iphone-4s-1635763610?utm_medium=referr al&utm_source=pulsenews

Detection rule for Office 365

Hi
I'm about to create a application for Office 365 in Configuration Manager 2012 R2.
I've seen recommendation to look for %programfiles%\Microsoft Office 15\root\Office15. But will that not break when office is upgraded on the client?
In registry I've HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\O365ProPlusRetail - en-us. And for the looks of it I cannot use this if a user decides to download and install a different version than en-us.
Any idea on what detection rule I should use for Office 365 that works for next versions of Office 365 (office 2015)?

Using folder check for "%programfiles%\Microsoft Office 15\root\Office15", might be a bad
idea.
You need to use the full path to WINWORD.exe or something.
If you install Visio using Office 365 it will end up in the same folder, and that will make wrong detection of the application!
You don't have to worry about the version of Office when running Office 365, but you can get the version directly from the
WINWORD.exe if you for some reason wants to use it...
I would recommend that you don't check for the version though.
Ronni Pedersen | Microsoft MVP - ConfigMgr | Blogs:
www.ronnipedersen.com/ and www.SCUG.dk/ | Twitter
@ronnipedersen

No Fax Detected

My fax keeps printing a No fax detected report several times a day. I have read that I need to go into advanced setting and turn off private fax but I do not have that option.

Hello there! Welcome to the forums @thegoodwins ,
I read about the fax report printing out for you and not being able to turn off this option. Please let me know which printer model you have and I will check out the options for you!
How Do I Find My Model Number?
Best wishes,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

No fax detected CM2320 MFP

I keep a NO FAX DETECTED on my HP CM2320 MFP series printer. everything was fine 2 days ago. I canot receive any faxes.
Thanks
Laureen

Hello there! Welcome to the forums @thegoodwins ,
I read about the fax report printing out for you and not being able to turn off this option. Please let me know which printer model you have and I will check out the options for you!
How Do I Find My Model Number?
Best wishes,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Internet security applications for XP - which one?

I'm about to do boot camp and add XP. Once I've turn the machine into a windows PC I'll need to have some anti-virus, firewall and all that. Don't trust XP's own offering.
Which is the most compatible internet security application when using Boot Camp and/or VMware Fusion? Has anyone got an 'avoid this' recommendation?
Thanks for any ideas.

For 10 yrs I've said, "avoid Norton" but I have to admit that Norton Internet Security 2008 really is good, a complete ground-up rewrite and works very well and I'm not even aware it is there unless I want to. Working.
AVG Suite was annoying, in your face, and why I had to find a replacement. It just bogs system down and always asking or telling you and wants to put a notification up (which goes away after 30 seconds).
Real-time AV applications - for viral malware.
Do not utilize more than one (1) real-time anti-virus scanning engine.
Disable the e-mail scanning function during installation (Custom
Installation on some AV apps.) as it provides no additional protection.
http://www.oehelp.com/OETips.aspx#3
Some experts believe that scanning incoming and outgoing mail causes e-mail file corruption.
Avira AntiVir® PersonalEdition Classic - Free
http://www.free-av.com/antivirus/allinonen.html
Free antivirus - avast! 4 Home Edition
http://www.avast.com/eng/avast4home.html
(Choose Custom Installation and under Resident
Protection, uncheck: Internet Mail and Outlook/Exchange.)
AVG Anti-Virus Free Edition
http://free.grisoft.com/
On-demand AV application.
(add it to your arsenal and use it as a "second opinion" av scanner).
BitDefender10 Free Edition
http://www.bitdefender.com/PRODUCT-14-en--BitDefender-8-Free-Edition.html
A-S applications - for non-viral malware.
The effectiveness of an individual A-S scanners can be wide-ranging and
oftentimes a collection of scanners is best. There isn't one software that
cleans and immunizes you against everything. That's why you need multiple
products to do the job i.e. overlap their coverage - one may catch what
another may miss, (grab'em all).
SuperAntispyware - Free
http://www.superantispyware.com/superantispywarefreevspro.html
Ad-Aware - Free
http://www.lavasoftusa.com/products/adawarefree.php
http://www.download.com/3000-2144-10045910.html
Spybot Search & Destroy - Free
http://www.safer-networking.org/en/download/index.html
Windows Defender - Free (build-in in Vista)
http://www.microsoft.com/athome/security/spyware/software/default.mspx
Interesting reading:
http://www.pcworld.com/article/id,136195/article.html
"...Windows Defender did excel in behavior-based protection, which detects
changes to key areas of the system without having to know anything about
the actual threat."
A clarification on the terminology: the word "malware" is short for
"malicious software." Most Anti-Virus applications detect many types of
malware such as viruses, worms, trojans, etc.
What AV applications usually don't detect is "non-viral" malware, and the
term "non-viral malware" is normally used to refer to things like spyware
and adware.
Some more useful applications:
Spyware Blaster - Free
http://www.javacoolsoftware.com/spywareblaster.html
Rootkit Revealer - Free
http://www.microsoft.com/technet/sysinternals/Utilities/RootkitRevealer.mspx
Crap Cleaner - Free
http://www.filehippo.com/download_ccleaner/
If Windows Defender is utilized go to Applications, under Utilities
uncheck "Windows Defender".
CW Shredder - Free
http://www.softpedia.com/get/Internet/Popup-Ad-Spyware-Blockers/CWShredder.shtml

Application Server, Message Server, Gateway

Hi,
Can anybody tell me which transaction in SAP gives me the details (Name and port) of the application server, message server, gateway server/service?
Regards,
Kishore

Kishore,
Check transaction SM50 for Servers & ports..
Bipin
P.S. Pls. award points if you find this useful.

CUCM 9.1.1 - MGCP gateway won't register to my 2811

Hello
I am trying to add a MGCP gateway on a 2811.
I have configured as per the book, but it is not registering,
here is my Router config:
2811 uptime is 2 hours, 4 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-11.XJ4.bin"
Cisco 2811 (revision 53.50) with 509952K/14336K bytes of memory.
Processor board ID FHK1302F0YV
3 FastEthernet interfaces
24 Serial interfaces
1 Channelized T1/PRI port
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
125440K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
2811#sh run
Building configuration...
Current configuration : 7125 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 2811
boot-start-marker
boot-end-marker
card type t1 0 2
enable secret 5 $1$ax07$1yOFpGS1rHGYm873l9n9q/
no aaa new-model
clock timezone PCLAIRE -5
clock summer-time PCLAIRE recurring
network-clock-participate wic 2
network-clock-select 1 T1 0/2/0
ip cef
no ip dhcp use vrf connected
ip domain name homelab.local
multilink bundle-name authenticated
isdn switch-type primary-ni
voice-card 0
dspfarm
dsp services dspfarm
controller T1 0/2/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description Home_PBX
vlan internal allocation policy ascending
interface FastEthernet0/0/0
description To Home Network$ETH-LAN$
ip address 192.168.15.50 255.255.255.0
duplex auto
speed auto
interface Serial0/2/0:23
description Home_PBX
no ip address
encapsulation ppp
isdn switch-type primary-ni
isdn incoming-voice voice
control-plane
voice-port 0/2/0:23
description Home_PBX
ccm-manager mgcp
ccm-manager config server 192.168.15.11 - THIS IS THE SUBSCRIBER , SHOULD IT BE THE PUBLISHER ?
ccm-manager config
mgcp
gateway
timer receive-rtp 1200
Here is what I get:
2811(config)#do sh ccm-manager
MGCP Domain Name: 2811.homelab.local
Priority        Status                   Host
============================================================
Primary         None
First Backup    None
Second Backup   None
Current active Call Manager:    None
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            09:55:04 PCLAIRE Jan 16 2014 (elapsed time: 02:00:24)
Last MGCP traffic time:         11:34:19 PCLAIRE Jan 16 2014 (elapsed time: 00:21:08)
Last failover time:             None
Last switchback time:           None
Switchback mode:                Graceful
MGCP Fallback mode:             Not Selected
Last MGCP Fallback start time: None
Last MGCP Fallback end time:    None
MGCP Download Tones:            Disabled
Backhaul/Redundant link is down
Configuration Auto-Download Information
=======================================
No configurations downloaded
Current state: Downloading XML file
Configuration Download statistics:
        Download Attempted             : 1
          Download Successful          : 1
          Download Failed              : 0
        Configuration Attempted        : 0
          Configuration Successful     : 0
          Configuration Failed(Parsing): 0
          Configuration Failed(config) : 0
Last config download command:
FAX mode: cisco
Configuration Error History:
2811(config)#
Any help greatly appreciated
John Bachman

Still same problem, I have erased all that related to mgcp on my router, to start from scratch
2811(config)#controller T1 0/2/0
2811(config-controller)#pri-group timeslots 1-24 service mgcp
Cannot overwrite no serv type with one. Unconfigure existing configuration and reconfigure
2811(config-controller)#
Where is this error coming from ??
Here is what I want to try:
192.168.15.10 - pub
192.168.15.11 - sub
controller T1 0/2/0
pri-group timeslots 1-24 service mgcp
interface Serial0/0/0:23
isdn bind-l3 ccm-manager
ccm-manager config server 192.168.15.10 192.168.15.11
ccm-manager config
ccm-manager redundant-host 192.168.15.11
ccm-manager mgcp
mgcp
mgcp call-agent 192.168.15.10 service-type mgcp version 0.1

FAX Detection Application for a MGCP Gateway

Similar Messages

Maybe you are looking for