FCid Persistent
Hi.
I work with a MDS9513 version 5.0(1a), and Fabric Manager version 4.1(1b), HDS USPV and hosts Dell R900 with Red Hat Enterprise 5.
A few days ago, a HBA connected in a port was replaced by another HBA(Other host) and the first HBA continued in map's Traffic Manager in the same port with the new one.
In switch, by CLI, I discovered the old HBA's wwn and fcid continues in the vsan, I deleted wwn the vsan, but in the map I have to go in the option vsan's domain and deleted too. Hard work. Then, I resolved no use fcid persistent: no fcdomain fcid persistent vsan X.
My question, Is it correct? Is it a good practice? Can I use the same for vsan 1?
Thks,
Paulo Maurício
Ok Brian, but I still don't understanding why to enable fcid pesistent. I only have hosts (Solaris, WIndows and Red Hat) and storage Hitachi connected. Do you think in the future I am going have problems? Is so important hosts and ports in storage have always the same fcid? In Fabric Manager, I had a problem when I changed the host connected in a interface, the both wwn, older and new, appeared on the map.
Thks for your intersting and help.
Paulo
Similar Messages
-
Configuring Persistent FC IDs for IVR
Has anybody configured this for IVR ? I use persistent FC IDs for my regular VSANs because i have a couple of AIX boxes. I will also have a couple of them access storage via IVR, dynamic tracking is not enabled on the host so i am wondering if i should enabled persistent fc id for IVR ?
ThanksSure
Assuming a single MDS using vsan 1 and vsan 2, both vsans using domain ID 0x12.
HBA is pwwn1, Storage is pwwn2
config term
This is to export the storage array that resides in vsan 2, into vsan 1 as fcid 0xaa3344
ivr fcdomain database autonomous-fabric-num 1 vsan 1
native-autonomous-fabric-num 1 native-vsan 2 domain 0xAA
pwwn pwwn2 fcid 0xAA3344
This is to export the hba that resides in vsan 1, into vsan 2 as fcid 0x232323
ivr fcdomain database autonomous-fabric-num 1 vsan 2
native-autonomous-fabric-num 1 native-vsan 1 domain 0x23
pwwn pwwn1 fcid 0x232323
If there are multiple MDS in the IVR topology, these entries would need to be included in each of the IVR enabled MDS.
You can use CFS to form peers amongst the IVR enabled switches and then use the 'ivr commit' to propagate the config command to the other MDS.
In this example, domain ID 0x23 can not already exist in vsan 2, nor can any switch join vsan 2 using domain ID 0x23. The same is true for vsan 1 and domain 0xAA.
Lastly, this example does reflect overlapping vsan IDs. That is why both vsan 1 and 2 are in autonomous-fabric (AFID). Had there been multiple MDS, and overlapping VSAN numbers (IDs), then to use IVR, those overlapping VSANs must be configured in different AFIDs. Basically you can have a device in vsan 1, domain ID 0x12 and using IVR NAT have it zoned with another device, in another MDS, in vsan 1, using domain ID 0x12, as long as the vsans are in different AFIDs.
The intent is not to design SANs this way, but if you have case where 2 existing SANs need to have some devices communicate, and neither SAN can change the existing vsan numbers and domain IDs, there is a way to connect the 2 devices and let them remain in the same vsan keeping the same FCID.
I would always recommend putting these static entries in place, before creating and activating the IVR zoneset. I would not recommend adding in the static entries (unless they matched what was currently in use) , as I am not sure if the MDS would log out the devices to enforce the new static mappings. It may only use the database when the zoneset is activated, or it could put it into effect immediately.
-now you know what I know
Mike -
Maintaining Same FCID with a port vsan change
I recently went through a VSAN consolidation where i took 2 VSANs and combined them into a new VSAN. The problem i have run into is that even after making sure that the domain id's of the source and destination VSANs were the same, the fcid's of the individual ports that were in the source VSAN changed when i moved them into the new VSAN. For HP-UX systems, this is a huge issue because HP-UX uses the fcid of the storage port to generate it's HW addresses for disks. With the fcid of the storage ports changing, this caused all of the HP-UX systems to reconfigure thier HW addresses and ended up causing some systems to crash.
To make it worse, when i try to go into domain manager in device manager to change the fcid back to what it was, the switch has already reassigned the original fcid to something else. And even when i find one that hasn't been, and i try to change it, it complains about a duplicate WWN. there are no duplicate WWN's.... :-(
Question1:
Is it possible to maintain the same FCID when changing the vsan assignment of a port?
Question2: I noticed that persistant fcids is enabled for both domains. do i simply need to disable that in order to change the fcid back to what it was?
Thanks!
BobBob
I've not done this in a while so going from meory here....
Q1: Yes it is as long as the domin ID is the same (which it looks like you've done). I think you need to remove the device from the SAN before you can delete the FCID. Also, I think you need to add the new FCID before you reconnect it.
Q2: You want persistant ID's on, without that a switch restart will mean all new FCID's all over again.
Having said all of that, I've migrated HP-UX boxes (and older AIX boxes without port tracking enabled) and not had to maintain the FCID. I assume you have/had 2 fabrics and the HP boxes are dual attached? IF thats the case, and you have working multipathing, then whilst you do have to do some remedial work on the boxes, you will not have system crashes / loss of access to data.
Steven -
Question
I am not able to launch FF everytime i try to open it, it says FF has to submit a crash report,and restore yr tabs. I even tried doing that and the report was submitted too, but still FF did not start, and the problem still persists, please help me solve this issue
'''(in English)'''Hi Danny,
Per my understanding that you can't get the expect result by using the expression "=Count(Fields!TICKET_STATUS.Value=4) " to count the the TICKET_STATUS which value is 4, the result will returns the count of all the TICKET_STATUS values(206)
but not 180, right?
I have tested on my local environment and can reproduce the issue, the issue caused by you are using the count() function in the incorrect way, please modify the expression as below and have a test:
=COUNT(IIF(Fields!TICKET_STATUS.Value=4 ,1,Nothing))
or
=SUM(IIF(Fields!TICKET_STATUS=4,1,0))
If you still have any problem, please feel free to ask.
Regards,
Vicky Liu
Vicky Liu
TechNet Community Support -
I'm using share point 2007 under windows server 2008 R2(one web server, another db server).When I publish a excel(*.xlsx) to report library or view it in web browser with the same error as bellows:
Excel Web Access
An error has occurred.
Please contact your system administrator if this problem persists.
Please kindly support to guide how to fix it with bellow information in details such as log.Many thanks!
1. The 12/logs file is as bellows:
10/10/2014 09:53:55.18 w3wp.exe (0x6528) 0x5C08 Excel Services
Excel Calculation Services 2u7d Medium ExcelServerSharedWebApplication.Local: An exception was thrown by configdb infrastructure: System.InvalidOperationException: ExcelServerSharedWebApplication.Local: Could
not get ServerContext.Current, which indicates that either SharePoint or the SSP infrastructure isn't provisioned correctly or that we're running outside of a web context. at Microsoft.Office.Excel.Server.ExcelServerSharedWebApplication.get_Local().
10/10/2014 09:53:55.18 w3wp.exe (0x6528) 0x5C08 Excel Services
Excel Services Administration 8tqh Critical Excel Services: Unexpected exception while trying to access Shared Services Database;. Error = ExcelServerSharedWebApplication.Local: Could not get ServerContext.Current, which indicates that
either SharePoint or the SSP infrastructure isn't provisioned correctly or that we're running outside of a web context..
10/10/2014 09:53:55.18 w3wp.exe (0x6528) 0x5C08 Excel Services
Excel Web Access 6nfi Unexpected InternalEwr.OpenWorkbook - An unexpected exception in the ECS Proxy occurred. Message: Microsoft.Office.Excel.Server.ExcelServerSettingException:
An error has occurred. ---> System.InvalidOperationException: ExcelServerSharedWebApplication.Local: Could not get ServerContext.Current, which indicates that either SharePoint or the SSP infrastructure isn't provisioned correctly or that we're running
outside of a web context. at Microsoft.Office.Excel.Server.ExcelServerSharedWebApplication.get_Local() --- End of inner exception stack trace --- at Microsoft.Office.Excel.Server.ExcelServerSharedWebApplication.get_Local()
at Microsoft.Office.Excel.Server.ExcelServerSettings.get_Settings() at Microsoft.Office.Excel.Server.ExcelServerSettings.get_EcsList() at Microsoft.Office...
2.the event in event viewer is:
Log Name: Security
Source: Microsoft-Windows-Security-Auditing
Date: 2014/10/10 9:49:43
Event ID: 4625
Task Category: Logon
Level: Information
Keywords: Audit Failure
User: N/A
Computer: ***.net
Description:
An account failed to log on.
Subject:
Security ID: NULL SID
Account Name: -
Account Domain: -
Logon ID: 0x0
Logon Type: 3
Account For Which Logon Failed:
Security ID: NULL SID
Account Name: ***
Account Domain: ***
Failure Information:
Failure Reason: An Error occured during Logon.
Status: 0xc000006d
Sub Status: 0x0
Process Information:
Caller Process ID: 0x0
Caller Process Name: -
Network Information:
Workstation Name: ***
Source Network Address: ***
Source Port: 63664
Detailed Authentication Information:
Logon Process:
Authentication Package: NTLM
Transited Services: -
Package Name (NTLM only): -
Key Length: 0
This event is generated when a logon request fails. It is generated on the computer where access was attempted.
The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe.
The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network).
The Process Information fields indicate which account and process on the system requested the logon.
The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases.
The authentication information fields provide detailed information about this specific logon request.
- Transited services indicate which intermediate services have participated in this logon request.
- Package name indicates which sub-protocol was used among the NTLM protocols.
- Key length indicates the length of the generated session key. This will be 0 if no session key was requested.
Event Xml:
<Event xmlns="">
<System>
<Provider Name="Microsoft-Windows-Security-Auditing" Guid="{54849625-5478-4994-A5BA-3E3B0328C30D}" />
<EventID>4625</EventID>
<Version>0</Version>
<Level>0</Level>
<Task>12544</Task>
<Opcode>0</Opcode>
<Keywords>0x8010000000000000</Keywords>
<TimeCreated SystemTime="2014-10-10T01:49:43.563436300Z" />
<EventRecordID>37602685</EventRecordID>
<Correlation />
<Execution ProcessID="532" ThreadID="26096" />
<Channel>Security</Channel>
<Computer>***.net</Computer>
<Security />
</System>
<EventData>
<Data Name="SubjectUserSid">S-1-0-0</Data>
<Data Name="SubjectUserName">-</Data>
<Data Name="SubjectDomainName">-</Data>
<Data Name="SubjectLogonId">0x0</Data>
<Data Name="TargetUserSid">S-1-0-0</Data>
<Data Name="TargetUserName">***</Data>
<Data Name="TargetDomainName">***</Data>
<Data Name="Status">0xc000006d</Data>
<Data Name="FailureReason">%%2304</Data>
<Data Name="SubStatus">0x0</Data>
<Data Name="LogonType">3</Data>
<Data Name="LogonProcessName">
</Data>
<Data Name="AuthenticationPackageName">NTLM</Data>
<Data Name="WorkstationName">***</Data>
<Data Name="TransmittedServices">-</Data>
<Data Name="LmPackageName">-</Data>
<Data Name="KeyLength">0</Data>
<Data Name="ProcessId">0x0</Data>
<Data Name="ProcessName">-</Data>
<Data Name="IpAddress">***</Data>
<Data Name="IpPort">63664</Data>
</EventData>
</Event>Hi Tracy,
Have you changed something on your SharePoint 2007 environment recently before this issue occurred?
This issue may be related to Alternate Access Mappings settings like the following similar post, if you have configured AAM, you can check if this issue happened to some URLs, if it's the case, please add the problematic URLs as a Publish URLs for the default
zone for your web application, and also add these URLs as trusted locations, then check results again.
If above doesn't work, please enable ULS log on verbose level to get more useful log errors which time are corresponding to the errors occur.
https://social.technet.microsoft.com/Forums/en-US/c9ab4818-65c9-444d-be50-1bfed1f1509b/excel-web-access-web-part-works-on-intranet-but-not-internet?forum=sharepointgenerallegacy
http://blog.bugrapostaci.com/2011/09/08/how-to-enable-verbose-log-mode-on-moss-2007/
Thanks
Daniel Yang
TechNet Community Support -
How to populate/persist right-side of Shuttle in apex 3.1.2 after submit
In the new Shuttle I can only specify one LOV (select empname, empid from emp where empid not in (1,3,4)) but I also want to populate the right-side of the shuttle to show values which the non-members (select empname, empid from emp where empid in (2,5)) so that the user can make selections which persist after submit.
Rashid,
The method that worked for me was to:
1) Create the LOV to populate the Left side of the shuttle (unselected).
2) Define the Source property to populate the Right side (selected). In my case, I used a PL/SQL Function Body type, but any would work.
I set the Source Used to Always, so that my user always started with the same default selection, but if you set it to "Only set when session value is null", that should do what you're asking for.
Good luck (and thanks for the points by marking my answer helpful or correct),
Stew -
Persistent Store Problems for MYSQL Enhanced Cluster With OpenMQ 4.4
I am trying to implement an enhanced cluster with failover. I have edited the config files for each broker instance for a persistent store. I have appended the following to each of the config.properties files:
imq.brokerid=myclusterinstanceINSTANCE1 # I substitute INSTANCE2 for INSTANCE1 for broker #2
imq.persist.store=jdbc
imq.persist.jdbc.dbVendor=mysql
imq.persist.jdbc.mysql.property.url=jdbc:mysql://xxx.xxx.xxx.xx:3306/test
imq.persist.jdbc.mysql.user=user1
imq.persist.jdbc.mysql.needpassword=true
imq.persist.jdbc.mysql.password=mypass
imq.cluster.ha=true
imq.cluster.clusterid=mycluster
imq.cluster.brokerlist=xxx.xxx.xxx.x:37676,yyy.yyy.yyy.y:37676
I then create the persistence storage with "imqdbmgr create tbl". When I view the data in the tables it creates, I have one row. Under Store_Version, I have 410. Under LOCK_ID, it has NULL. When I go to start the brokers with imqbrokerd, I get the following error:
ERROR [B3198]: Error initializing cluster manager:
com.sun.messaging.jmq.jmsserver.util.BrokerException: [B4239]: Failed to load persistent store version from database table MQVER41Cmycluster
at com.sun.messaging.jmq.jmsserver.persist.jdbc.VersionDAOImpl.getStoreVersion(VersionDAOImpl.java:310)
at com.sun.messaging.jmq.jmsserver.persist.jdbc.DBTool.updateStoreVersion410IfNecessary(DBTool.java:350)
at com.sun.messaging.jmq.jmsserver.persist.jdbc.JDBCStore.checkStore(JDBCStore.java:3599)
at com.sun.messaging.jmq.jmsserver.persist.jdbc.JDBCStore.<init>(JDBCStore.java:127)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
at java.lang.Class.newInstance0(Class.java:355)
at java.lang.Class.newInstance(Class.java:308)
at com.sun.messaging.jmq.jmsserver.persist.StoreManager.getStore(StoreManager.java:157)
at com.sun.messaging.jmq.jmsserver.Globals.getStore(Globals.java:967)
at com.sun.messaging.jmq.jmsserver.cluster.ha.HAClusterManagerImpl.initialize(HAClusterManagerImpl.java:181)
at com.sun.messaging.jmq.jmsserver.Globals.initClusterManager(Globals.java:903)
at com.sun.messaging.jmq.jmsserver.Broker._start(Broker.java:777)
at com.sun.messaging.jmq.jmsserver.Broker.start(Broker.java:410)
at com.sun.messaging.jmq.jmsserver.Broker.main(Broker.java:1971)
Caused by: java.lang.NullPointerException
at com.mysql.jdbc.ResultSetImpl.findColumn(ResultSetImpl.java:1103)
at com.mysql.jdbc.ResultSetImpl.getInt(ResultSetImpl.java:2777)
at com.sun.messaging.jmq.jmsserver.persist.jdbc.VersionDAOImpl.getStoreVersion(VersionDAOImpl.java:298)
... 16 more
I believe this error is attributed to the NULL value under LOCK_ID. I think that the value under LOCK_ID should be the name of the broker from the config file (even though I specified them in the config files). Any ideas?? THANKS!Just some pointers -- maybe this will be of use:
If you haven't already read it, please take a look at the [ MySQL setup guide|https://mq.dev.java.net/OpenMQ_MySQLCluster_Setup_Guide.html] .
We recommend using NDB Data-store of MySQL Cluster, though this isn't an absolute requirement. Due to some issues we have found with earlier versions, we recommend using MySQL Cluster, 7.0.9 or better (the current version is 7.0.16, or 7.1.5). Either of these would contain Connector/J.
I'd also recommend using the latest version -- MQ 4.4update2 (just in case you happen to have an older copy). There were many minor improvements in the integration with MySQL from the original 4.4 release, to update 2. This is linked at the MQ download page: [https://mq.dev.java.net/downloads.html] -
ISCSIprt errors with persistent disconnections
What we need:
==========
Determine why we have Persistent iSCSIprt errors in Hyper-V cluster Windows Server 2012
Environment:
==========
4x identical hosts Dell R720 running Windows server 2012 standard
4x - iSCSI NICs: Intel(R) Gigabit 4P I350-t Adapter - Driver 12.1.76.0 - FW Family 13.0.0
MTU set to 9000
Chimey disabled, auto Tuning disabled, congestion provider set to None
All kinds of OffLoad features were disabled in the iSCSI NICs properties
No teaming configuration is in place
RSS/TOE/TOEv2, Virtual Machine Queue (VMQ) and energy saving options are disabled
2x PCT6224 - FW 3.3.5.5
2 stack cables interconnecting them
STP port-fast enabled on all ethernet ports
MUT set to 9216 on all ethernet ports
Flow control is active in all ports
Speed in 1000 full duplex being auto negotiated
Multi, broad and unicast storm disable
None errors logged in any ethernet or stack ports
3x EQL Storages
2x EQPS6100X + 1x PS4100E all running 6.0.4
Current situation:
===========
Customer is experiencing timeout and disconnections:
* All four hosts are logging the following System Events every 1 minute:
ID 9 / Source iScsiPrt / Target did not respond in time for a SCSI request. The CDB is given in the dump data.
ID 39 / Source iScsiPrt / Initiator sent a task management command to reset the target. The target name is given in the dump data.
ID 129 / Source iScsiPrt / No Description
This events shows up only in Windows Server 2012 environment, the issue was isolated and do not occur with Windows Server 2008 in the same SAN.
Troubleshooting steps so far:
===================
Disable windows Firewall and make sure the non-san subnets are excluded in the hit kit *
Make sure the latest drivers from Dell D&D are installed for the iSCSI NICs
Jumbo Fram size setup correctly.
Disabled TOE, RSS and Large Send Offload, FlowControl setup
netsh interface tcp set global autotuninglevel=disable netsh int tcp set global chimney=disabled netsh interface tcp set global rss=disabled
Followed some practices from here:
http://en.community.dell.com/support-forums/storage/f/3775/p/19480319/20326067.aspx
RSS/TOE/TOEv2, Virtual Machine Queue (VMQ) and energy saving options are disabled
All nodes are updated with the latest rollup update.
Teaming not configured.
Changed binding order on NICS
Disabled NetBIOS on iSCSI • Made sure that each NIC is NOT set to register its connection in DNS • Remove File and Printer sharing and Client from Microsoft networks
Following updates were applied:
http://support.microsoft.com/kb/2791465/en-US ( kb 2779768 )
http://support.microsoft.com/kb/2795944/en-US
http://support.microsoft.com/kb/2822241/en-US
http://support.microsoft.com/kb/2808584/en-US
http://support.microsoft.com/?id=2838669
http://support.microsoft.com/?id=2813630 suprimido no KB2838669
http://support.microsoft.com/?id=2796000
http://support.microsoft.com/?id=2795997
http://support.microsoft.com/?id=2795993
http://support.microsoft.com/kb/2838669
Disabled TCP Delay ACK in Server
Switches: STP port-fast enabled in all ethernet ports + MUT set to 9216 in all ethernet ports + Flow control is active in all ports + Unicast storm disabled
Captured iScsi traffic with wareshark
Anyone can help us?
VPHello,
I have three Hyper-V 2012 (not R2) nodes and I'm experiencing similar issues.
I get iscsiprt error suddenly after a storage migration of a big VM ends: I launch the storage migration, it starts correctly and, more or less 60 seconds after it ends, iscsiprt errors appears in the event log of the node. I lose iSCSI connectivity with
the iSCSI target on the storage were the VM was on before migration. The storage migrated VM works because is already moved to the "new" storage but obviously all the CSV on the "old" storage become inaccessible, I can see them offline
or online (no access) so all the VMs that are on the old storage goes offline.
I noticed that it didn't happen eveytime I storage migrate a VM, but only sometimes and with big VMs.
I tried both with MPIO and with MCS since our storage supports both of them. I tuned some iSCSI parameters on the initiator. I leave a list of parameters I tried to tune at the end of this message.
The only thing I didn't do already is: disable RSS, disable TCP autotuninglevel and disable delayed ACK.
Someone can help me to understand what is causing these problems? What is AV you are referring to?
This is the parameters I tuned in order to increase timeouts but right now I didn't yet solved the problem:
HKLM\SYSTEM\CurrentControlSet\Services\mpio\Parameters
UseCustomPathRecoveryInterval 0 -> 1
PDORemovePeriod 20 -> 120
PathRecoveryInterval 40 -> 40
HKLM\SYSTEM\CurrentControlSet\Control\Class\{4D36E97B-E325-11CE-BFC1-08002BE10318}\<Instance Number>\Parameters
EnableNOPOut 0 -> 1
MaxRequestHoldTime 60 -> 90
LinkDownTime 15 -> 35
Thanks in Advance,
Davide -
Error - PERSIST - MSGGUID_EXISTING
Hi All,
I am getting the below error, Could you please sugges me how to reslove this error..
Error
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Request Message Mapping
-->
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="PERSIST">MSGGUID_EXISTING</SAP:Code>
<SAP:P1>B87C667272184CBD01299EC41DA840BB</SAP:P1>
<SAP:P2>CENTRAL</SAP:P2>
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Message ID B87C667272184CBD01299EC41DA840BB for pipeline CENTRAL, version already exists in system</SAP:Stack>
<SAP:Retry>N</SAP:Retry>
</SAP:Error>
Trace
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Request Message Mapping
-->
- <SAP:Trace xmlns:SAP="http://sap.com/xi/XI/Message/30">
<Trace level="1" type="T">Party normalization: sender</Trace>
<Trace level="1" type="T">Sender scheme external = XIParty</Trace>
<Trace level="1" type="T">Sender agency external = http://sap.com/xi/XI</Trace>
<Trace level="1" type="T">Sender party external =</Trace>
<Trace level="1" type="T">Sender party normalized =</Trace>
<Trace level="1" type="T">Party normalization: receiver</Trace>
<Trace level="1" type="T">Receiver scheme external =</Trace>
<Trace level="1" type="T">Receiver agency external =</Trace>
<Trace level="1" type="T">Receiver party external =</Trace>
<Trace level="1" type="T">Receiver party normalized =</Trace>
<Trace level="1" type="B" name="CL_XMS_HTTP_HANDLER-HANDLE_REQUEST" />
- <!-- ************************************
-->
<Trace level="1" type="T">XMB was called with URL /sap/xi/engine?type=entry</Trace>
<Trace level="2" type="T">Request Line = POST /sap/xi/engine?type=entry HTTP/1.1</Trace>
<Trace level="2" type="T">Host = topwdsxid001.rails.rwy.bnsf.com:8001</Trace>
<Trace level="2" type="T">Server protocol = HTTP/1.1</Trace>
<Trace level="2" type="T">Remote address = 139.51.100.47</Trace>
<Trace level="1" type="T">COMMIT is done by XMB !</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-ENTER_XMS" />
- <!-- ************************************
-->
<Trace level="1" type="B" name="CL_XMS_MAIN-SET_START_PIPELINE" />
- <!-- ************************************
-->
<Trace level="3" type="T">XMB was called with external pipeline PID = ENTRY</Trace>
<Trace level="3" type="T">Getting type of XMB...</Trace>
<Trace level="1" type="B" name="SXMBCONF-SXMB_GET_XMB_USE" />
<Trace level="2" type="T">XMB kind = CENTRAL</Trace>
<Trace level="3" type="T">Start pipeline found</Trace>
<Trace level="2" type="T">Switch to external start pipeline PID = CENTRAL</Trace>
- <Trace level="1" type="B" name="CL_XMS_TROUBLESHOOT-ENTER_PLSRV">
<Trace level="3" type="T">No triggers found. OK.</Trace>
</Trace>
<Trace level="1" type="T">****************************************************</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">XMB entry processing</Trace>
<Trace level="3" type="T">system-ID = DX1</Trace>
<Trace level="3" type="T">client = 200</Trace>
<Trace level="3" type="T">language = E</Trace>
<Trace level="3" type="T">user = PIAFUSERDX1</Trace>
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">****************************************************</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_UC_EXECUTE">
<Trace level="1" type="T">Message-GUID = B87C667272184CBD01299EC41DA840BB</Trace>
<Trace level="1" type="T">PLNAME = CENTRAL</Trace>
<Trace level="1" type="T">QOS = BE</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PIPELINE_SYNC" />
- <!-- ************************************
-->
<Trace level="1" type="T">Get definition of external pipeline CENTRAL</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-LOOKUP_INTERNAL_PL_ID">
<Trace level="3" type="T">External PLID = CENTRAL</Trace>
<Trace level="3" type="T">Internal PLID = SAP_CENTRAL</Trace>
</Trace>
<Trace level="1" type="T">Corresponding internal pipeline SAP_CENTRAL</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline attributes</Trace>
<Trace level="3" type="T">PID = SAP_CENTRAL</Trace>
<Trace level="3" type="T">ENABLE = 1</Trace>
<Trace level="3" type="T">TRACELEVEL = 0</Trace>
<Trace level="3" type="T">EXEMODE = A</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline elements</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_INTERFACE_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_MAPPING_REQUEST</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_OUTBOUND_BINDING</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_CALL_ADAPTER</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_MAPPING_RESPONSE</Trace>
<Trace level="3" type="T" />
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>
</Trace>
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET Begin of pipeline processing PLSRVID = CENTRAL</Trace>
- <Trace level="1" type="B" name="PLSRV_RECEIVER_DETERMINATION">
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET Start of pipeline service processing PLSRVID= PLSRV_RECEIVER_DETERMINATION</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="3" type="T">Calling pipeline service: PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">Reading Pipeline-Service specification...</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline service specification (table SXMSPLSRV)</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">ADRESSMOD = LOCAL</Trace>
<Trace level="3" type="T">P_CLASS = CL_RD_PLSRV</Trace>
<Trace level="3" type="T">P_IFNAME = IF_XMS_PLSRV</Trace>
<Trace level="3" type="T">P_METHOD = ENTER_PLSRV</Trace>
<Trace level="3" type="T">FL_LOG =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_RD_PLSRV-ENTER_PLSRV">
<Trace level="1" type="T">R E C E I V E R - D E T E R M I N A T I O N</Trace>
<Trace level="1" type="T">Cache Content is up to date</Trace>
<Trace level="2" type="T">Start without given receiver</Trace>
<Trace level="2" type="T">Classic Receiver Determination via Rules.</Trace>
<Trace level="2" type="T">Check conditions for rule line no. 1</Trace>
<Trace level="2" type="T">...valid Receiver w/o Condition: - DE1CLNT301</Trace>
<Trace level="2" type="T">No Receiver found behaviour: 0</Trace>
<Trace level="2" type="T">Number of Receivers:1</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET End of pipeline service processing PLSRVID= PLSRV_RECEIVER_DETERMINATION</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>
</Trace>
- <Trace level="1" type="B" name="PLSRV_INTERFACE_DETERMINATION">
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET Start of pipeline service processing PLSRVID= PLSRV_INTERFACE_DETERMINATION</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="3" type="T">Calling pipeline service: PLSRV_INTERFACE_DETERMINATION</Trace>
<Trace level="3" type="T">Reading Pipeline-Service specification...</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline service specification (table SXMSPLSRV)</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_INTERFACE_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">ADRESSMOD = LOCAL</Trace>
<Trace level="3" type="T">P_CLASS = CL_ID_PLSRV</Trace>
<Trace level="3" type="T">P_IFNAME = IF_XMS_PLSRV</Trace>
<Trace level="3" type="T">P_METHOD = ENTER_PLSRV</Trace>
<Trace level="3" type="T">FL_LOG =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_ID_PLSRV-ENTER_PLSRV">
<Trace level="1" type="T">I N T E R F A C E - D E T E R M I N A T I O N</Trace>
<Trace level="1" type="T">Cache Content is up to date</Trace>
<Trace level="2" type="T">Check conditions for (Inb: Party Srvc If) DE1CLNT301 MI_FF_MQ_IB</Trace>
<Trace level="2" type="T">...valid InbIf without Condition: MI_FF_MQ_IB</Trace>
<Trace level="2" type="T">Number of receiving Interfaces:1</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET End of pipeline service processing PLSRVID= PLSRV_INTERFACE_DETERMINATION</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>
</Trace>
- <Trace level="1" type="B" name="PLSRV_RECEIVER_MESSAGE_SPLIT">
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET Start of pipeline service processing PLSRVID= PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="3" type="T">Calling pipeline service: PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
<Trace level="3" type="T">Reading Pipeline-Service specification...</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline service specification (table SXMSPLSRV)</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">ADRESSMOD = LOCAL</Trace>
<Trace level="3" type="T">P_CLASS = CL_XMS_PLSRV_RECEIVER_SPLIT</Trace>
<Trace level="3" type="T">P_IFNAME = IF_XMS_PLSRV</Trace>
<Trace level="3" type="T">P_METHOD = ENTER_PLSRV</Trace>
<Trace level="3" type="T">FL_LOG =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_XMS_PLSRV_RECEIVER_SPLIT-ENTER_PLSRV">
<Trace level="3" type="T">Case handling for different plsrv_ids PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
<Trace level="2" type="T">got property produced by receiver determination</Trace>
<Trace level="1" type="T">number of receivers: 1</Trace>
<Trace level="1" type="T">Single-receiver split case</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET End of pipeline service processing PLSRVID= PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>
</Trace>
<Trace level="1" type="B" name="PLSRV_MAPPING_REQUEST" />
- <!-- ************************************
-->
<Trace level="1" type="Timestamp">2008-12-23T22:31:21Z CET Start of pipeline service processing PLSRVID= PLSRV_MAPPING_REQUEST</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="3" type="T">Calling pipeline service: PLSRV_MAPPING_REQUEST</Trace>
<Trace level="3" type="T">Reading Pipeline-Service specification...</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline service specification (table SXMSPLSRV)</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_MAPPING_REQUEST</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">ADRESSMOD = LOCAL</Trace>
<Trace level="3" type="T">P_CLASS = CL_MAPPING_XMS_PLSRV3</Trace>
<Trace level="3" type="T">P_IFNAME = IF_XMS_PLSRV</Trace>
<Trace level="3" type="T">P_METHOD = ENTER_PLSRV</Trace>
<Trace level="3" type="T">FL_LOG =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL" />
- <!-- ************************************
-->
<Trace level="1" type="B" name="CL_MAPPING_XMS_PLSRV3-ENTER_PLSRV" />
- <!-- ************************************
-->
<Trace level="2" type="T">......attachment XI_Context not found</Trace>
<Trace level="3" type="T">Mapping already defined in interface determination</Trace>
<Trace level="3" type="T">Object ID of Interface Mapping B8617742EF783B61AC162A69924F0C20</Trace>
<Trace level="3" type="T">Version ID of Interface Mapping EE72E5C042A411DDBCA8ECA98B33649F</Trace>
<Trace level="1" type="T">Interface Mapping http://bnsf.com/generic IM_I_FF_MQ</Trace>
<Trace level="3" type="T">Mapping Steps 1 JAVA com/sap/xi/tf/_MM_I_FF_TXT_MAP_ 2 JAVA com/sap/xi/tf/_MM_I_FF_O_RFC_</Trace>
<Trace level="3" type="T">Dynamic Configuration Is Empty</Trace>
<Trace level="2" type="T">Mode 0</Trace>
<Trace level="3" type="T">Creating mapping sequence with 2 steps.</Trace>
<Trace level="3" type="T">Creating step 0.</Trace>
<Trace level="3" type="T">Creating Java mapping com/sap/xi/tf/_MM_I_FF_TXT_MAP_.</Trace>
<Trace level="3" type="T">Creating step 1.</Trace>
<Trace level="3" type="T">Creating Java mapping com/sap/xi/tf/_MM_I_FF_O_RFC_.</Trace>
<Trace level="3" type="T">Start executing mapping sequence with 2 steps.</Trace>
<Trace level="3" type="T">Executing mapping step 0</Trace>
<Trace level="2" type="T">Call method execute of the application Java mapping com.sap.xi.tf._MM_I_FF_TXT_MAP_</Trace>
<Trace level="1" type="T">RuntimeException during appliction Java mapping com/sap/xi/tf/_MM_I_FF_TXT_MAP_</Trace>
<Trace level="1" type="T">com.sap.aii.utilxi.misc.api.BaseRuntimeException: RuntimeException in Message-Mapping transformation: Cannot produce target element /ns0:MT_I_FF. Check xml instance is valid for source xsd and target-field mapping fulfills requirements of target xsd at com.sap.aii.mappingtool.tf3.AMappingProgram.start(AMappingProgram.java:420) at com.sap.aii.mappingtool.tf3.Transformer.start(Transformer.java:142) at com.sap.aii.mappingtool.tf3.AMappingProgram.execute(AMappingProgram.java:118) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:64) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.SequenceMapping.executeStep(SequenceMapping.java:55) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor251.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy232.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor253.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.call(RFCDefaultRequestHandler.java:284) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:219) at com.sap.engine.services.rfcengine.RFCJCOServer$J2EEApplicationRunnable.run(RFCJCOServer.java:254) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172) Root Cause: com.sap.aii.mappingtool.tf3.IllegalInstanceException: Cannot produce target element /ns0:MT_I_FF. Check xml instance is valid for source xsd and target-field mapping fulfills requirements of target xsd at com.sap.aii.mappingtool.tf3.AMappingProgram.processNode(AMappingProgram.java:300) at com.sap.aii.mappingtool.tf3.AMappingProgram.start(AMappingProgram.java:415) at com.sap.aii.mappingtool.tf3.Transformer.start(Transformer.java:142) at com.sap.aii.mappingtool.tf3.AMappingProgram.execute(AMappingProgram.java:118) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:64) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.SequenceMapping.executeStep(SequenceMapping.java:55) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor251.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy232.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor253.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.call(RFCDefaultRequestHandler.java:284) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:219) at com.sap.engine.services.rfcengine.RFCJCOServer$J2EEApplicationRunnable.run(RFCJCOServer.java:254) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172)</Trace>
<Trace level="1" type="T">Runtime exception occurred during execution of application mapping program com/sap/xi/tf/_MM_I_FF_TXT_MAP_: com.sap.aii.utilxi.misc.api.BaseRuntimeException; RuntimeException in Message-Mapping transformation: Cannot produce target element /ns0:MT_I_FF. Check xml instance is valid for source xsd and target-field mapping fulfills requirements of target xsd</Trace>
<Trace level="1" type="T">com.sap.aii.ibrun.server.mapping.MappingRuntimeException: Runtime exception occurred during execution of application mapping program com/sap/xi/tf/_MM_I_FF_TXT_MAP_: com.sap.aii.utilxi.misc.api.BaseRuntimeException; RuntimeException in Message-Mapping transformation: Cannot produce target element /ns0:MT_I_FF. Check xml instance is valid for source xsd and target-field mapping fulfills requirements of target xsd at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:73) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.SequenceMapping.executeStep(SequenceMapping.java:55) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor251.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy232.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor253.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.call(RFCDefaultRequestHandler.java:284) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:219) at com.sap.engine.services.rfcengine.RFCJCOServer$J2EEApplicationRunnable.run(RFCJCOServer.java:254) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172) Root Cause: com.sap.aii.utilxi.misc.api.BaseRuntimeException: RuntimeException in Message-Mapping transformation: Cannot produce target element /ns0:MT_I_FF. Check xml instance is valid for source xsd and target-field mapping fulfills requirements of target xsd at com.sap.aii.mappingtool.tf3.AMappingProgram.start(AMappingProgram.java:420) at com.sap.aii.mappingtool.tf3.Transformer.start(Transformer.java:142) at com.sap.aii.mappingtool.tf3.AMappingProgram.execute(AMappingProgram.java:118) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:64) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.SequenceMapping.executeStep(SequenceMapping.java:55) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor251.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy232.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor253.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.call(RFCDefaultRequestHandler.java:284) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:219) at com.sap.engine.services.rfcengine.RFCJCOServer$J2EEApplicationRunnable.run(RFCJCOServer.java:254) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172) Root Cause: com.sap.aii.mappingtool.tf3.IllegalInstanceException: Cannot produce target element /ns0:MT_I_FF. Check xml instance is valid for source xsd and target-field mapping fulfills requirements of target xsd at com.sap.aii.mappingtool.tf3.AMappingProgram.processNode(AMappingProgram.java:300) at com.sap.aii.mappingtool.tf3.AMappingProgram.start(AMappingProgram.java:415) at com.sap.aii.mappingtool.tf3.Transformer.start(Transformer.java:142) at com.sap.aii.mappingtool.tf3.AMappingProgram.execute(AMappingProgram.java:118) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:64) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.SequenceMapping.executeStep(SequenceMapping.java:55) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor251.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy232.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor253.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.call(RFCDefaultRequestHandler.java:284) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:219) at com.sap.engine.services.rfcengine.RFCJCOServer$J2EEApplicationRunnable.run(RFCJCOServer.java:254) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172)</Trace>
<Trace level="1" type="E">CL_XMS_PLSRV_MAPPING~ENTER_PLSRV</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST">
<Trace level="3" type="T">Persisting message Status = 023</Trace>
<Trace level="3" type="T">Message version 000</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</Trace>
</Trace>
<Trace level="1" type="T">SystemError message generated. Guid: DDD1416C1925D1F1A0F200101816A382</Trace>
<Trace level="1" type="T">Error during execution of message : B87C667272184CBD01299EC41DA840BB</Trace>
<Trace level="1" type="T">ApplicationMessage was (=RefToMsgId): B87C667272184CBD01299EC41DA840BB</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST" />
- <!-- ************************************
-->
<Trace level="3" type="T">Persisting message Status = 023</Trace>
<Trace level="3" type="T">Message version 000</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</SAP:Trace>
Thanks for your time,
SR
Edited by: S R on Dec 24, 2008 12:09 AMThanks Jag / Gaurav,
now i am getting different error...
Error
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Receiver Identification
-->
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="PERSIST">MSGGUID_EXISTING</SAP:Code>
<SAP:P1>28ACBC00283740FE35749BC9DC995832</SAP:P1>
<SAP:P2>CENTRAL</SAP:P2>
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Message ID 28ACBC00283740FE35749BC9DC995832 for pipeline CENTRAL, version already exists in system</SAP:Stack>
<SAP:Retry>N</SAP:Retry>
</SAP:Error>
Trace
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Receiver Identification
-->
- <SAP:Trace xmlns:SAP="http://sap.com/xi/XI/Message/30">
<Trace level="1" type="T">Party normalization: sender</Trace>
<Trace level="1" type="T">Sender scheme external = XIParty</Trace>
<Trace level="1" type="T">Sender agency external = http://sap.com/xi/XI</Trace>
<Trace level="1" type="T">Sender party external =</Trace>
<Trace level="1" type="T">Sender party normalized =</Trace>
<Trace level="1" type="T">Party normalization: receiver</Trace>
<Trace level="1" type="T">Receiver scheme external =</Trace>
<Trace level="1" type="T">Receiver agency external =</Trace>
<Trace level="1" type="T">Receiver party external =</Trace>
<Trace level="1" type="T">Receiver party normalized =</Trace>
<Trace level="1" type="B" name="CL_XMS_HTTP_HANDLER-HANDLE_REQUEST" />
- <!-- ************************************
-->
<Trace level="1" type="T">XMB was called with URL /sap/xi/engine?type=entry</Trace>
<Trace level="2" type="T">Request Line = POST /sap/xi/engine?type=entry HTTP/1.1</Trace>
<Trace level="2" type="T">Host = topwdsxid001.rails.rwy.bnsf.com:8001</Trace>
<Trace level="2" type="T">Server protocol = HTTP/1.1</Trace>
<Trace level="2" type="T">Remote address = 139.51.100.47</Trace>
<Trace level="1" type="T">COMMIT is done by XMB !</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-ENTER_XMS" />
- <!-- ************************************
-->
<Trace level="1" type="B" name="CL_XMS_MAIN-SET_START_PIPELINE" />
- <!-- ************************************
-->
<Trace level="3" type="T">XMB was called with external pipeline PID = ENTRY</Trace>
<Trace level="3" type="T">Getting type of XMB...</Trace>
<Trace level="1" type="B" name="SXMBCONF-SXMB_GET_XMB_USE" />
<Trace level="2" type="T">XMB kind = CENTRAL</Trace>
<Trace level="3" type="T">Start pipeline found</Trace>
<Trace level="2" type="T">Switch to external start pipeline PID = CENTRAL</Trace>
- <Trace level="1" type="B" name="CL_XMS_TROUBLESHOOT-ENTER_PLSRV">
<Trace level="3" type="T">No triggers found. OK.</Trace>
</Trace>
<Trace level="1" type="T">****************************************************</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">XMB entry processing</Trace>
<Trace level="3" type="T">system-ID = DX1</Trace>
<Trace level="3" type="T">client = 200</Trace>
<Trace level="3" type="T">language = E</Trace>
<Trace level="3" type="T">user = PIAFUSERDX1</Trace>
<Trace level="1" type="Timestamp">2008-12-23T22:32:00Z CET</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">****************************************************</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_UC_EXECUTE">
<Trace level="1" type="T">Message-GUID = 28ACBC00283740FE35749BC9DC995832</Trace>
<Trace level="1" type="T">PLNAME = CENTRAL</Trace>
<Trace level="1" type="T">QOS = BE</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PIPELINE_SYNC" />
- <!-- ************************************
-->
<Trace level="1" type="T">Get definition of external pipeline CENTRAL</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-LOOKUP_INTERNAL_PL_ID">
<Trace level="3" type="T">External PLID = CENTRAL</Trace>
<Trace level="3" type="T">Internal PLID = SAP_CENTRAL</Trace>
</Trace>
<Trace level="1" type="T">Corresponding internal pipeline SAP_CENTRAL</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline attributes</Trace>
<Trace level="3" type="T">PID = SAP_CENTRAL</Trace>
<Trace level="3" type="T">ENABLE = 1</Trace>
<Trace level="3" type="T">TRACELEVEL = 0</Trace>
<Trace level="3" type="T">EXEMODE = A</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline elements</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_INTERFACE_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_MAPPING_REQUEST</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_OUTBOUND_BINDING</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_CALL_ADAPTER</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_MAPPING_RESPONSE</Trace>
<Trace level="3" type="T" />
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>
</Trace>
<Trace level="1" type="Timestamp">2008-12-23T22:32:00Z CET Begin of pipeline processing PLSRVID = CENTRAL</Trace>
<Trace level="1" type="B" name="PLSRV_RECEIVER_DETERMINATION" />
- <!-- ************************************
-->
<Trace level="1" type="Timestamp">2008-12-23T22:32:00Z CET Start of pipeline service processing PLSRVID= PLSRV_RECEIVER_DETERMINATION</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="3" type="T">Calling pipeline service: PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">Reading Pipeline-Service specification...</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline service specification (table SXMSPLSRV)</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">ADRESSMOD = LOCAL</Trace>
<Trace level="3" type="T">P_CLASS = CL_RD_PLSRV</Trace>
<Trace level="3" type="T">P_IFNAME = IF_XMS_PLSRV</Trace>
<Trace level="3" type="T">P_METHOD = ENTER_PLSRV</Trace>
<Trace level="3" type="T">FL_LOG =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL" />
- <!-- ************************************
-->
- <Trace level="1" type="B" name="CL_RD_PLSRV-ENTER_PLSRV">
<Trace level="1" type="T">R E C E I V E R - D E T E R M I N A T I O N</Trace>
<Trace level="1" type="T">Cache Content is up to date</Trace>
<Trace level="2" type="T">Start without given receiver</Trace>
<Trace level="1" type="T">No Relation found - accept given Receivers.</Trace>
<Trace level="2" type="T">Classic Receiver Determination via Rules.</Trace>
<Trace level="2" type="T">No Receiver found behaviour: 0</Trace>
</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST">
<Trace level="3" type="T">Persisting message Status = 023</Trace>
<Trace level="3" type="T">Message version 000</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</Trace>
</Trace>
<Trace level="1" type="T">SystemError message generated. Guid: DDD1417FD2DAD8F1A0F200101816A382</Trace>
<Trace level="1" type="T">Error during execution of message : 28ACBC00283740FE35749BC9DC995832</Trace>
<Trace level="1" type="T">ApplicationMessage was (=RefToMsgId): 28ACBC00283740FE35749BC9DC995832</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST" />
- <!-- ************************************
-->
<Trace level="3" type="T">Persisting message Status = 023</Trace>
<Trace level="3" type="T">Message version 000</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</SAP:Trace>
Audit Log[Runtime workbench]
Error Returning synchronous error notification to calling application: com.sap.aii.af.ra.ms.api.RecoverableException: Received HTTP response code 404 : Not Found.
Error Transmitting the message using connection http://sap1.xxxx.com:50100/sap/xi/engine?type=entry failed, due to: com.sap.aii.af.ra.ms.api.DeliveryException: Received HTTP response code 404 : Not Found.
Error The message status set to FAIL.
Error Returning to application. Exception: com.sap.aii.af.ra.ms.api.DeliveryException: Received HTTP response code 404 : Not Found
Error Attempt to process file failed with com.sap.aii.af.ra.ms.api.DeliveryException: Received HTTP response code 404 : Not Found
Edited by: S R on Dec 24, 2008 3:05 AM -
Why is my JavaServiceFacade persist() method is receiving NULL object
My jDeveloper version is 11.1.1.3.0
I have a jspx in which i want to save an employee into my DB on the click of submit button.
I have made an entity object(Employee.java) made from a table EMPLOYEE. I then exposed this entity bean using a JavaServiceFacade. This JavaServiceFacade class has a method with signature persistEmployee(Employee employee).
In my UI, i have made made a Submit button by dragging the persistEmployee() method from my DataControls pallette to my jspx, and the actionListener binding for this is ="#{bindings.persistEmployees.execute}".
Now when i click on the submit button, the persistEmployee() method throws an exception which is below...
______ java.lang.IllegalArgumentException: Object: null is not a known entity type_______
I found that the persistEmployee() method is not receiving an Employee object as an argument due to which this error is thrown.
Can somebody pls guide me on what could be the issue.
BELOW ISTHE CODE WHICH I HAVE USED.
.......button code in my jsp.......
<af:commandButton text="Submit"
binding="#{backing_LdapUserCreation.cb5}"
id="cb5"
actionListener="#{bindings.persistEmployees.execute}"
disabled="#{!bindings.persistEmployees.enabled}"/>
.......method code which got generated in teh javaservicefacade..(here the employee argument received by the first line is NULL).....
public Employees persistEmployees(Employees employees) {
System.out.println("IS employees NULL ? = "+employees);
return (Employees)_persistEntity(employees);
.......binding code in my pagedefinition.........
<methodAction id="persistEmployees" RequiresUpdateModel="true"
Action="invokeMethod" MethodName="persistEmployees"
IsViewObjectMethod="false" DataControl="EmployeeService"
InstanceName="EmployeeService.dataProvider"
ReturnName="EmployeeService.methodResults.persistEmployees_EmployeeService_dataProvider_persistEmployees_result">
<NamedData NDName="employees" NDType="model.test.Employees" />
</methodAction>Hi,
when you dragged the persist method from the DataControls panel, a dialog opens that in its lower area shows the argument that the method expects. This argument needs to be pointed to <iterator name> | currentRow | data provider. To do this, click into the method argument value field and click the button on its right to bring up the EL editor. Then expand the iterator node under the Bindings node. Expand currentRow and select dataProvider.
You can do this after creating the method binding as well. Select the PageDef file in the Application Navigator and open the Structure Window. Expand the persist method: it shoudl have a child element. Select the child item and in the Property Inspector set its NDValue property
Frank -
Issues in persisting dynamic entity and view objects using MDS
Hi All,
I'm trying to create dynamic entity and view objects per user session and to persist these objects throughout the session, I'm trying to use MDS configurations(either file or Database) in adf-config.xml.
I'm facing following two errors while trying to run the app module:
1. MDS error (MetadataNotFoundException): MDS-00013: no metadata found for metadata object "/model/DynamicEntityGenModuleOperations.xml"
2. oracle.mds.exception.ReadOnlyStoreException: MDS-01273: The operation on the resource /sessiondef/dynamic/DynamicDeptEntityDef.xml failed because source metadata store mapped to the namespace / DEFAULT is read only.
I've gone through the following links which talks about the cause of the issue, but still can't figure out the issue in the code or the config file. Please help if, someone has faced a similar issue.
[http://docs.oracle.com/cd/E28271_01/doc.1111/e25450/mds_trouble.htm#BABIAGBG |http://docs.oracle.com/cd/E28271_01/doc.1111/e25450/mds_trouble.htm#BABIAGBG ]
[http://docs.oracle.com/cd/E16162_01/core.1112/e22506/chapter_mds_messages.htm|http://docs.oracle.com/cd/E16162_01/core.1112/e22506/chapter_mds_messages.htm]
Attached is the code for dynamic entity/view object generation and corresponding adf-config.xml used.
///////////App Module Implementation Class/////////////////////////
public class DynamicEntityGenModuleImpl extends ApplicationModuleImpl implements DynamicEntityGenModule {
private static final String DYNAMIC_DETP_VO_INSTANCE = "DynamicDeptVO";
* This is the default constructor (do not remove).
public DynamicEntityGenModuleImpl() {
public ViewObjectImpl getDepartmentsView1() {
return (ViewObjectImpl) findViewObject("DynamicDeptVO");
public void buildDynamicDeptComp() {
ViewObject internalDynamicVO = findViewObject(DYNAMIC_DETP_VO_INSTANCE);
if (internalDynamicVO != null) {
System.out.println("OK VO exists, return Defn- " + internalDynamicVO.getDefFullName());
return;
EntityDefImpl deptEntDef = buildDeptEntitySessionDef();
ViewDefImpl viewDef = buildDeptViewSessionDef(deptEntDef);
addViewToPdefApplicationModule(viewDef);
private EntityDefImpl buildDeptEntitySessionDef() {
try {
EntityDefImpl entDef = new EntityDefImpl(oracle.jbo.server.EntityDefImpl.DEF_SCOPE_SESSION, "DynamicDeptEntityDef");
entDef.setFullName(entDef.getBasePackage() + ".dynamic." + entDef.getName());
entDef.setName(entDef.getName());
System.out.println("Application Module Path name: " + getDefFullName());
System.out.println("EntDef :" + entDef.getFileName() + " : " + entDef.getBasePackage() + ".dynamic." + entDef.getName());
entDef.setAliasName(entDef.getName());
entDef.setSource("DEPT");
entDef.setSourceType("table");
entDef.addAttribute("ID", "ID", Integer.class, true, false, true);
entDef.addAttribute("Name", "NAME", String.class, false, false, true);
entDef.addAttribute("Location", "LOCATION", Integer.class, false, false, true);
entDef.resolveDefObject();
entDef.registerSessionDefObject();
entDef.writeXMLContents();
entDef.saveXMLContents();
return entDef;
} catch (Exception ex) {
System.out.println(ex.getLocalizedMessage());
return null;
private ViewDefImpl buildDeptViewSessionDef(EntityDefImpl entityDef) {
try {
ViewDefImpl viewDef = new oracle.jbo.server.ViewDefImpl(oracle.jbo.server.ViewDefImpl.DEF_SCOPE_SESSION, "DynamicDeptViewDef");
viewDef.setFullName(viewDef.getBasePackage() + ".dynamic." + viewDef.getName());
System.out.println("ViewDef :" + viewDef.getFileName());
viewDef.setUseGlueCode(false);
viewDef.setIterMode(RowIterator.ITER_MODE_LAST_PAGE_FULL);
viewDef.setBindingStyle(SQLBuilder.BINDING_STYLE_ORACLE_NAME);
viewDef.setSelectClauseFlags(ViewDefImpl.CLAUSE_GENERATE_RT);
viewDef.setFromClauseFlags(ViewDefImpl.CLAUSE_GENERATE_RT);
viewDef.addEntityUsage("DynamicDeptUsage", entityDef.getFullName(), false, false);
viewDef.addAllEntityAttributes("DynamicDeptUsage");
viewDef.resolveDefObject();
viewDef.registerSessionDefObject();
viewDef.writeXMLContents();
viewDef.saveXMLContents();
return viewDef;
} catch (Exception ex) {
System.out.println(ex.getLocalizedMessage());
return null;
private void addViewToPdefApplicationModule(ViewDefImpl viewDef) {
oracle.jbo.server.PDefApplicationModule pDefAM = oracle.jbo.server.PDefApplicationModule.findDefObject(getDefFullName());
if (pDefAM == null) {
pDefAM = new oracle.jbo.server.PDefApplicationModule();
pDefAM.setFullName(getDefFullName());
pDefAM.setEditable(true);
pDefAM.createViewObject(DYNAMIC_DETP_VO_INSTANCE, viewDef.getFullName());
pDefAM.applyPersonalization(this);
pDefAM.writeXMLContents();
pDefAM.saveXMLContents();
////////adf-config.xml//////////////////////
<?xml version="1.0" encoding="windows-1252" ?>
<adf-config xmlns="http://xmlns.oracle.com/adf/config" xmlns:config="http://xmlns.oracle.com/bc4j/configuration" xmlns:adf="http://xmlns.oracle.com/adf/config/properties"
xmlns:sec="http://xmlns.oracle.com/adf/security/config">
<adf-adfm-config xmlns="http://xmlns.oracle.com/adfm/config">
<defaults useBindVarsForViewCriteriaLiterals="true"/>
<startup>
<amconfig-overrides>
<config:Database jbo.locking.mode="optimistic"/>
</amconfig-overrides>
</startup>
</adf-adfm-config>
<adf:adf-properties-child xmlns="http://xmlns.oracle.com/adf/config/properties">
<adf-property name="adfAppUID" value="TestDynamicEC-8827"/>
</adf:adf-properties-child>
<sec:adf-security-child xmlns="http://xmlns.oracle.com/adf/security/config">
<CredentialStoreContext credentialStoreClass="oracle.adf.share.security.providers.jps.CSFCredentialStore" credentialStoreLocation="../../src/META-INF/jps-config.xml"/>
</sec:adf-security-child>
<persistence-config>
<metadata-namespaces>
<namespace metadata-store-usage="mdsRepos" path="/sessiondef/"/>
<namespace path="/model/" metadata-store-usage="mdsRepos"/>
</metadata-namespaces>
<metadata-store-usages>
<metadata-store-usage default-cust-store="true" deploy-target="true" id="mdsRepos">
<metadata-store class-name="oracle.mds.persistence.stores.file.FileMetadataStore">
<property name="metadata-path" value="/tmp"/>
<!-- <metadata-store class-name="oracle.mds.persistence.stores.db.DBMetadataStore">
<property name="jndi-datasource" value="jdbc/TestDynamicEC"/>
<property name="repository-name" value="TestDynamicEC"/>
<property name="jdbc-userid" value="adfmay28"/>
<property name="jdbc-password" value="adfmay28"/>
<property name="jdbc-url" value="jdbc:oracle:thin:@localhost:1521:XE"/>-->
</metadata-store>
</metadata-store-usage>
</metadata-store-usages>
</persistence-config>
</adf-config>
//////////////////////////////////////////////////////////////////////////////////////////////////////////Hi Frank,
I m trying to save entity and view object xml by calling writeXMLContents() and saveXMLContents() so that these objects can be retrieved using the xmls later on.
These methods internally use MDS configuration in adf-config.xml, which is creating the issue.
Please share your thoughts on resolving this or if, there is any other way of creating dynamic entity/view objects for db tables created at runtime.
Nik -
Issues with sessionId and persistent cookie in WL6.1
I am using WL6.1 and I discovered the following from a brief experiment using a
JSP which sets persistent cookies. The results are the same when I use IE browser
or the HDML emulator.
The name of the weblogic session cookie (weblogic.xml) is "_ses".
Steps below. The server logs are included:
1. Delete the persistent cookies relevant to the server.
2. Access the jsp. SessionId is generated, say 12345.
3. Close browser. My_Cookie1=blah is saved on client.
4. Access server again. The cookie My_Cookie1=blah sent
5. The server sets the SessionId to Cookie1=blah. The sessionId is set from the
persistent cookie. Also, the String after the first underscore is the sessionId.
When I change the name of the weblogic session cookie (weblogic.xml) to something
without an underscore, such as "JSESSIONID" or "someCookieName", and repeat the
steps, the sessionId is not attempted to be read from the persistent cookie.
Why is this so?
Thanks,
Niranjan
LOG AFTER HITTING FIRST TIME (STEP 2)
================================
test.jsp: Hit
session id (O8tS4HMN3KSYK!1003180768699)
ctr: null
--------- HTTP REQUEST HEADERS BEGIN -------------
DEVSNIFF-header(1): Accept=image/gif, image/x-xbitmap, image/jpeg, image/pjpeg,
application/vnd.ms-powerpoint, application/vnd.ms-excel, app
lication/msword, */*
DEVSNIFF-header(2): Accept-Language=en-us
DEVSNIFF-header(3): Accept-Encoding=gzip, deflate
DEVSNIFF-header(4): User-Agent=Mozilla/4.0 (compatible; MSIE 5.01; Windows NT
5.0)
DEVSNIFF-header(5): Host=nk
DEVSNIFF-header(6): Connection=Keep-Alive
--------- HTTP REQUEST HEADERS END -------------
LOG AFTER HITTING SECOND TIME (STEP 5)
===================================
test.jsp: Hit
session id (Cookie1=59631091!1003180798903)
ctr: null
--------- HTTP REQUEST HEADERS BEGIN -------------
DEVSNIFF-header(1): Accept=image/gif, image/x-xbitmap, image/jpeg, image/pjpeg,
application/vnd.ms-powerpoint, application/vnd.ms-excel, app
lication/msword, */*
DEVSNIFF-header(2): Accept-Language=en-us
DEVSNIFF-header(3): Accept-Encoding=gzip, deflate
DEVSNIFF-header(4): User-Agent=Mozilla/4.0 (compatible; MSIE 5.01; Windows NT
5.0)
DEVSNIFF-header(5): Host=nk
DEVSNIFF-header(6): Connection=Keep-Alive
DEVSNIFF-header(7): Cookie=My_Cookie1=59631091
--------- HTTP REQUEST HEADERS END -------------
CHANGED _ses TO JSESSIONID (RESULT: CORRECT SESSION ID GENERATED)
==========================
test.jsp: Hit
session id (O8tZKVgE4LuPo!1003182377496)
ctr: null
--------- HTTP REQUEST HEADERS BEGIN -------------
DEVSNIFF-header(1): Accept=image/gif, image/x-xbitmap, image/jpeg, image/pjpeg,
application/vnd.ms-powerpoint, application/vnd.ms-excel, app
lication/msword, */*
DEVSNIFF-header(2): Accept-Language=en-us
DEVSNIFF-header(3): Accept-Encoding=gzip, deflate
DEVSNIFF-header(4): User-Agent=Mozilla/4.0 (compatible; MSIE 5.01; Windows NT
5.0)
DEVSNIFF-header(5): Host=nk
DEVSNIFF-header(6): Connection=Keep-Alive
--------- HTTP REQUEST HEADERS END -------------
test.jsp: Hit
session id (O8tZRy1Wq3o9T!1003182407901)
ctr: null
--------- HTTP REQUEST HEADERS BEGIN -------------
DEVSNIFF-header(1): Accept=image/gif, image/x-xbitmap, image/jpeg, image/pjpeg,
application/vnd.ms-powerpoint, application/vnd.ms-excel, app
lication/msword, */*
DEVSNIFF-header(2): Accept-Language=en-us
DEVSNIFF-header(3): Accept-Encoding=gzip, deflate
DEVSNIFF-header(4): User-Agent=Mozilla/4.0 (compatible; MSIE 5.01; Windows NT
5.0)
DEVSNIFF-header(5): Host=nk
DEVSNIFF-header(6): Connection=Keep-Alive
DEVSNIFF-header(7): Cookie=My_Cookie1=88575204
--------- HTTP REQUEST HEADERS END -------------
[test.jsp]
Issue 1 is a know "feature" with Macs using an optical output.
Issue 2 is still unresolved. Why can't Front Row act as a video jukebox just as well as it can for audio.
Issue 3 is still unresolved. If I select a libray that has both audio and video files, Front Row will only play the audio and not the video. Seems like it should be smart enough to "switch" to play that video.
Issue 4 seems to be resolved. I run visualizer all the time now and my TV does not switch out of 1080i any more.
Issue 5 seems to be resolved. I think the trick is that the TV show name has to be filled in for the system to recognize it as a TV show. Guess Apple didn't orginally figure people would add TV shows not purchsed through the iTunes store.
Issue 6 was realted to using files that are copy protected. But why iTunes XML file can't just keep the name that I want in it's directory rather than the name that is embedded in the file is still a mystery to me. -
When I publish my site on one specific page where I've added {tag_pagecontent} I get the error:
'Some files on the server may be missing or incorrect. Clear browser cache and try again. If the problem persists please contact website author.'
I'm trying to get a blog module going, I've even deleted the html insert bog with the tag in and re-published which then I don't get the error but as a result no blog either. But then I add the tag in again and publish the error comes back. I've used the dev console and it says that my musicians sample.css is out of date but why is it only out of date when I add in html to my muse site?
HELP!!!! I've searched other threads and to no avail I'm publishing so no direct ftp going on. the only thing I changed in business catalyst was the module stylesheet in order to style the blog. I've tried uploading and replacing all files nothing seems to work. the site is here:
http://www.musicstudentsforhire.co.uk/musicians-samples.html
It's only this page as it has the blog on. Also I've noticed when I've re-published occasionally it will show the mobile version on my desktop and not the desktop version??? no idea why that's happening so I've had to turn that off. any explanation on why that is happening would also be much appreciated.I haven't received an answer as of yet, I'll post t on here when I do. I de-activated the mobile site because it's my clients site so he needs it to be operational during the day. I hope someone gives me an answer soon.
-
Page numbers from deleted book file persist in document
I have 4 documents that I needed to merge so I attempted to put them in a book file (which I am not at all familiar with how to use). I removed the documents from the book file because it was not doing what I needed it to do, but the auto section page numbers are persisting in the individual documents and I cannot get rid of them. For example I have page numbering starting on page 5, but pages 1-4 have page numbers 5-8 on them and I cannot get rid of them. (I can do this manually of course but would like to know why they are persisting)
Do you mean the numbers physically appear on the pages and you don't want them there (if so, delete them from the master page(s)) or do you mean the numbering scheme is wrong (if so, check your section and numbering options)?
-
Persistent Chat (Lync Server 2013) with Lync 2010 Group Chat
I have successfully deployed Lync Server 2013 and both 2013 and 2010 desktop clients connect and function as expected.
The problem is with Persistent Chat. It works perfectly with the 2013 desktop client but - whilst 2010 Group Chat connects - I receive the error message "The [LOGON_DOMAIN] is not available". No chat rooms are available and I am unable to search.
I have been unable to locate anything on the web which discusses the problem.
I do not know whether this makes a difference but the 2010 clients use terminals rather than dedicated workstations.
Can anyone shed any light on what the problem may be?Have you created a CsPersistentChatEndpoint to allow the Group Chat client (2010) to connect to Persistent
Chat server? Please take a look at: http://technet.microsoft.com/en-us/library/jj204901.aspx
Please mark posts as answers/helpful if it answers your question.
Blog
Lync Validator - Used to assist in the validation and documentation of Lync Server 2013.
Maybe you are looking for
-
How do i transfer songs from itunes to my ipod
I tried to transfer a song that i bought from the itunes library to my ipod but a message always pops up that says i am not authorized to play it on my computer. what does this mean and how do i put the song on my ipod?
-
Raw files transferring from iPhoto into Lightroom as JPEGs
I know this makes me sound like a newbie but in lightroom 3 the raw files were listes as .crw when I imported them from iphoto but in lightroom 4.1 they are showing up as .jpg. Am I doing something wrong? Are these actually RAW files I am working wi
-
Looking for FULL SCREEN flash web gallery template
Hi, I'm looking for a plugin for PS to make full screen flash gallery, something similar to this: http://www.paulvanroekel.nl/picasa/CoolFullScreendemo/index.html anyone know of any? free would also be good Cheers, TBK
-
Two problems with video: Import and gamma
I downloaded and tried LR4 today and found the new adjustment features quite impressive. I was also very eager to try the new video facilities. Woudl have loved to... Running on iMAC with Lion, pictures and video from a Pentax K5. Video is full HD @2
-
Weblogic Portal 7.0 to iPlanet Authentication
I have a lot of questions, but first, I will tell you about our problem and our setup. We are trying to use iPlanet as our Authentication piece for WLP 7.0, and we are running into problems and exceptions. First, we setup iPlanet to have a group call