FCP export to "QuickTime Movie" distorts aspect ratio of all text, displays video correctly.

Hi you all,
My name is Alexander, I'm from Belgium.
I'm working on Final Cut Pro 6.0.6, on a MacBook Pro with a 2.53 GHz Intel Core 2 Duo Processor, running version 10.7.2 of Mac OS X (Lion).
I'm editing a 'making of' of a Flemish feature film. I shot this 35 minute documentary short with my own Canon HDV-camcorder (XH-A1). The Final Cut Pro-project is stored on an external hard drive (1 TB LaCie Minimus).
I've been doing exports to "QuickTime Movie" for years now, without any problems, but since a week or two, FCP started messing up the titles over the video - and the titles only. Their aspect ratio is messed up once exported, but they look just fine in the FCP Timeline (in Viewer, I can verify that the aspect ratio of the titles is always "0"). I'm trying to export this to "HDV - 720p25".
Here's a comparison between the two:
As you can see: the MOV has the titles' aspect ratio all weird, the upper one partly covering the lower one. All titles and text in the docu come out like this, but the video (and audio) is exported correctly.
Any ideas on how to solve this very annoying problem?
Many thanks!!
Alexander

Hi Studio X,
Thank you for your quick reply.
The producers of the film want to upload this making of-documentary on YouTube. Therefore, I need to give them a high-quality-mov with the least possible Megabites. My film has a 35 minute running time.
So I figured: Let's start with the 'smallest' high-quality FCP-export to begin with (HDV-720p25), and throw that one in Compressor, in order to end up with a 'small' but good looking H.264-MOV for YouTube.
But for some reason, those "HDV-720p25"-exports mess up the titles. And I can't figure out why.
Alexander

Similar Messages

Flash CS4, Exporting Quicktime Movie: size, aspect ratio, and alignment

I am new to Flash so this may be a basic question, but I have not been able to find anything in the help files or the forums.
I have tried several times to change the size of my quicktime movies, from 550 pixels by 400 pixels to 480 pixels by 480 pixels, and I cannot seem to do it. I have used "Modify > Document" and tried every option I could find through this command. Each time I export I double check that the export settings match my desired size, and they do, but when I open the movie in quicktime, it has been stretched to fit 550 x 400 pixels. The preview movie looks exactl how I want, it is only the exported movie that is incorrect.
Is it possible to make a quicktime movie of the size I would like, or is that a standard format that cannot be adjusted?
As a workaround, I have tried squeezing my 480x480 content into the 550x400 stage (while scaling it prportionally). but when I do this, the square of content is not centered in the background in quicktime. It is off center in the preview movie as well, and this commonly occurs after I have used "modify > document" to change the size of the document. The side to which it is aligned seems to be inconsistent.
Is there a way to realign the video after I have modified the document size? Does changing the document size through "modify > document" affect the centering and alignment of my video? Is there a way to change it back?
I have attached images of my videos in flash, and then what they look like after export.
Thanks in advance for any advice.
-Ben

to explain a little further . . .
the dark gray areas in my images delineate the content of the animation, and in the "550x400 after export" image, the black strip to the right is a margin showing the background color of the document, which is black. notice that there is only a margin on one side, and not both.
Thanks some more,
-Ben

Can't export to Quicktime in proper aspect ratio.

I'm working on a project with a:
-Canon XL2
Set to:
-16:9 SD
-24p 2:3:3:2 Pulldown
Capture Preset:
-DV NTSC 48 kHz Advanced (2:3:3:2) Pulldown Removal Anamorphic
Sequence Preset:
-DV NTSC 48 kHz - 23.98
When I try to export to Quicktime it smashes the image from the left and right. The Quicktime window appears to be displaying a 16:9 aspect ratio, but for some reason it distorts the image and places black bars on both sides. Does anyone have any idea what kind of export settings I should be using for this? If you need more info to answer my Q. just ask...I will be monitoring this post closely.
thanks,
iMac G5 Mac OS X (10.4.6) 2.0 GHz, 400Gb Hard Drive, 2Gb Ram, 250Gb External

I've tried exporting in several different ways. My first attempt was just the obligatory Export: Quicktime: Current Settings. Then I played around with the various settings to no avail. Unfortunately, I'm really not sure what the difference is between exporting to Quicktime and using Quicktime conversion. I also don't know the difference between 23.98, 24@25, and 24. Maybe if I understood the settings it would be easier to figure out.

HDV and FCP Export to Quicktime Movie

Hi.
Should I be able to "Export to Quicktime" a 90-minute FCP timeline and expect no hiccups? I keep trying and my Quicktime file has an occasional slight jump from one frame to another when I view it. This happens about once every 2-3 minutes.
Is the file too large to play back (13gig)? Do I not have a powerful enough computer or graphics card?
My goal is to play the movie using DVI-out to a theatre's DVI-in, so the film can be viewed in the best quality possible. I was hoping to output to a Quicktime, dump it to my MacBook and play it using the DVI-out.
Any thoughts or suggestions?
Specs:
~ MacPro Dual-Core Intel Xeon 2.66 GHz, 1 GB Ram
~ NVIDIA GeForce 7300 GT graphics card
~ Timeline: 720p at 24fps HDV native video
~ Outputting to Quicktime Uncompressed
~ MacBook: 2.16 GHz, 1 GB Ram
~ MacBook Video Card: Intel GMA 950 graphics processor with 64MB of DDR2 SDRAM shared with main memory4

Choose file/export/QuickTime Movie, and check on the "make self contained" option. Turn off the "recompress all frames" option. This is the best export there is for any source media format HDV or not... Might try exporting just a bit, and see if this movie will play back ok on a MacBook first though using the DVI out to another monitor... Don't change formats. Making it any other format will cause quality loss, or create a file so large that the macbook won't play it... I'd also suggest you put it on a fw drive to play back from the MacBook.
If it were me though, I'd not trust the Macbook to play it back OK... just not enough horsepower IMHO.
Jerry

Still photo in FCP exported to Photoshop, not matching aspect ratio

Hi,
I made a still photo in FCP. Sent to Photoshop. Imported back in FCP. Image is squished. I am using DV NTSC 720x480.
In Photoshop I also set Image Size to 720x480. For some reason I cant get it to match in FCP. Any idea how I an fix this?
Thanks.

I should add that the image has transparency.

Export to Quicktime Movie Results in Aspect Ratio Distortion

All of my original footage was shot in miniDV. I have created a sequence with the following settings:
Frame size: 720 x 480
Compressor: DV/DVCPRO - NTSC
Pixel Aspect: NTSC - CCIR 601
Vid rate: 29.97 fps
Ultimately the sequence needs to go to DVD with a standard 4:3 aspect ratio. To export, I am using:
File > Export > QuickTime Movie...
I have tried using several different settings including:
Apple Pro Res 422 NTSC 48 kHz
Apple Pro Res 422 NTSC (HQ) 48 kHz
Apple Pro Res 960x720 30p 48 kHz
DV NTSC 48 kHz
etc...
All settings yield the same result: a slightly squeezed aspect ratio. At first, I thought that this might simply be the fact that I was playing back files in QuickTime which uses square pixels I believe. But in both DVD Studio Pro and iDVD, the simulation shows the same effect. (By the way, Finder's "Get Info" reads the resulting Final Cut Pro Movie File dimensions 720x486.)
I'm fairly new to FCP so I'm hoping there is something obvious that I have missed. Can anyone explain what I need to do to get the video to DVD without a distorted aspect ratio?
(Incidentally, I have managed to export using quicktime conversion with no problem. But I need the export to be a Final Cut Pro Movie File so as to maintain chapter markers, etc.)
Advice welcome!!!

Hi David, I know this was discussed in you posting already but I just wanted to make sure I had it clear. I have a 4:3 film and I've exported as a quicktime movie with current settings, which should be 4:3 and found that the image when played back in quicktime, looks horizontally stretched. Almost as if quicktime is trying to play it back as a 16:9 image. I think this is the same issue the other fellow was having but I just wanted to be clear. You're saying that the 4:3 image distortion is perfectly normal when played back in quicktime on a computer screen and that the export will look fine when put to DVD or sent to a monitor? I just wanted to make sure because this problem is freaking me out and I don't want to deliver a distorted image to my client. Could you also explain briefly why this happens with quicktime export and not quicktime conversion and what causes quicktime to distort the 4:3 image? Any advice or help would be greatly appreciated.
Cheers,
james.

16x9 aspect ratio lost after FCP export to QT movie

I initially complained about the same problem when exporting from Motion to QT movie, then importing in FCP. This was fixed, and I really enjoy it.
I work 99% in DV anamorphic and all my Applications are set this way. It bothers me however that I lose my anamorphic aspect ratio when I export from FCP to Quicktime movie. Maybe I'm doing something wrong?
I hope this will be fixed in the next patch as it waists a lot of time correcting it manually. I often export from FCP and into QT Pro, fix aspect ratio and then off to the web. If anyone knows of a better way, I would appreciate the help.
Quad, 20" Widescreen, Microsoft Mouse Mac OS X (10.4.8) Final Cut Studio

I work 99% in DV anamorphic and all my Applications are set this way. It bothers me however that I lose my anamorphic aspect ratio when I export from FCP to Quicktime movie. Maybe I'm doing something wrong?
No, you're not doing anything wrong - this is a quirk in the way that FCP writes anamorphic QT movies when using the DV codecs.
As you've discovered, the flag is not recognized by QT Player unless you export via QT Conversion and either set the display size manually or, in QT 7.1.0 or higher, select 16:9 output in your Movie Settings.
Sorry if that's no help...

FCP: Motion Distort Aspect Ratio -33.33?

Good morning,
I recently exported two different sequences from FCP. Both films were exported using ‘QuickTime Movie’ and ‘Current Settings’.
One of the films came out letter-boxed and the other did not.
In investigating this I found the only difference in the settings of two films seems to be that under the 'Distort' field in 'Motion' tab of the FCP Viewer, the Aspect Ratio for the letter-boxed video was set at '-33.33' while for the full-screen the Aspect Ratio was set for '0'. When I changed the -33.33 to 0 I got the full-screen, non-letter-boxed image I wanted.
Both films are also played with QuickTime player using ‘Conform Aperture to: Clean’ under the ‘Presentation’ tab of [Command]-J.
Why was the Aspect Ratio for these clips set at -33.33? Since I didn't set this, it must have been an automatic setting.
I'm sure I'm missing something here.
Cheers,
BurntMonkey

Studio X,
Thanks again. 'Squeeze Mode' is the DVX100B's solution to fitting a 16:9 aspect on a 4:3 chip. If I understand correctly when in the mode the DVX basically animorphically squeezes the footage onto the chip. Then when it is handled in post the footage is 'stretched' and you are left with a 16:9 aspect ratio.
Yes, when I first drag a clip to the timeline, I do get the message about the sequence settings not matching and do I want to change them to match the current clip. Is this when the Aspect Ratio is set to -33.33?
My question is still 'Why?' When I reset the aspect ration back to '0' I get the full-screen, 16:9 image that I was hoping for in the first place. But I'm wondering when this will come back to haunt me. I have burned a DVD using the exported sequence so everything seems to be OK.
Thanks for your help in understanding this.
Cheers,
John

Distorted Aspect Ratio of Exported Frames

My project's aspect ratio is 16:9 (720 horizontal, 576 vertical).
I inserted a clip into the timeline.
I exported a certain frame to a file as an image.
The image file's size: 720 x 576.
I proceeded to import the image file into the project, and inserted it into the timeline.
The image's aspect ratio is not the same as the original footage.
Specifically, the horizontal side is narrower than originally (see attached screenshots).
What causes this discrepancy?
More importantly, what can i do to get exported frames to match the aspect ratio of the project?

OK, I've got the BMP. When I looked at your images, I thought that we were seeing your still image on the Timeline. We are not. That shape/size is what was produced.
Now, remember that I am on PrE 4, so things will be different in PrE 8. Still, I should be able to get you close. In PrE 4, one uses File>Export>Frame to do a Frame capture under the CTI (Current Time Indicator), and visible in the Program Monitor. When you choose this, you will get the standard Windows dialog screen, where you name and locate your still image. There is also a settings button, that will open up a second dialog box, for you to adjust many attributes of your Frame capture. There, you will have three choices in the left-hand Pane: General, Video and Keyframe and Rendering. First, go to General, and you'll get File Type w/ a dropdown. There, you can choose the format type and should have JPEG, TIFF, BMP, TARGA and GIF (maybe more in PrE 8, like PNG?). I'd stick with TIFF or BMP. About the only other choice is whether you want to add this captured still in your Project, or not. That is your choice.
Go to the Video listing in that left-hand Pane. There you can choose the Frame Size, the PAR and the Color Depth. Make sure that these match your Project's and your source footage's exact specs. Unless you need the Alpha Channel, and are using either TIFF or TARGA, leave Color Depth to Millions of colors. Otherwise, choose Millions +, where the + is that Alpha Channel.
I'd guess that it's in those settings, as to what is happening with your Frame capture. Let me know if you get this sorted, and sorry for my mis-step, but I was not clear on what I was seeing, and where I was seeing it.
Good luck,
Hunt

Export to Quicktime movie continued crashes. HELP

I have sequence, it renders no problem. Whenever I go to export to Quicktime movie it crashes. I have gone and deleted all files associated with it and redone the sequence from scratch, and I keep getting the same results. Crash while exporting. I am working in DV, so all I do at export is export to Quicktime movie, which means it should be exporting as a DV movie. I am not sure what is wrong please help.
As always thanks in advance for reading and replying to my Post,
Sebastian

I did try burning the 18.05GB file on i-DVD but even with the auto compression of i-DVD it only managed to compress it down to 5.4GB - too large for my 4.7GB DVD.
The only reason I need to burn it so my friend can author it is that he's a little too fussy and wants to author it on Adobe Encore.
I managed to get a firewire drive - but the blooming PC didnt accept it as it was Mac formated!
I just exported the original file as a QT movie, reducing sound quality, frame rate etc but it still comes out at 17.5GB - still to large for i-DVD (and thats with i-DVD's compression, which comes in at approx 5GB!)
I really really blame myself for this as I never really looked into anything more than the creative aspect of FCP. But I've started now.

I have a project in FCP that is a 2:1 aspect ratio. When I send to compressor to author a DVD I lose the aspect ratio and the image fills the 16x9 frame. How do I preserve the original ratio thru compressor?

Aspect ratio lost in compressor

Hi Tom, thanks so much for answering. I totally get the need to letterbox but my issue is, how do I get the best quality in letterbox format?
Should I export it thru QT Conversion or just Export to Quicktime Movie? I exported as a self contained movie to keep the quality but when I send it thru the MPEG-2 compressor for DVD it fills the 16x9 frame without letterbox.
How would I modify the MPEG-2 preset to give me the letterbox in the MPEG-2?
I've been playing around but haven't hit the jackpot yet.
If there's any info you have, it would be greatly appreciated.
Thanks so much
James

Export To Quicktime Movie (Reference or Self Contained) - GENERAL ERROR

Hi -
I recently had to re-install FCS2 due to problems with OSX.
Now, for some reason, when I want to export from FCP to get a QT reference movie, I get a general error message. All other options from FCP export seem to work, but NOT export to Quicktime Movie.
Any suggestions?
Thanks.
Chris

how so?
we can all do with a dummy's cheat sheet e.g. when making a master monitor the record device, not the computer.
So come on, what'd you do?

Export to Quicktime Movie rerendering. Why?

Hi
I have a DV project edited in FCP 5.11 which is all completely rendered. It's actually made up of a number of sequences joined end to end each of which is rendered before rendering the final 'top' sequence. There are some heavily rendered motion still sections in there, so I don't really want to render them again.
However when I Export to Quicktime Movie, using the current settings, ie not making a self-contained movie, it takes hours to render and looks like it is rerendering everything I painstakingly made sure was rendered to full quality already. Is there anything I can do to stop it doing this? (I am doing this to make things much easier for Compressor, rendering the whole project as a referenced movie.)
Thanks for your attention.
Regards
Jeff Cole
PowerMac G5 Dual 2Ghz Mac OS X (10.4.6)

Just checking that you are, in fact, leaving the menu as Current Settings... and not changing it to match the settings of your timeline...
Also, you say you are not making a self contained movie - you've left that unchecked? Are you sure you don't have any gray realtime bars over the top of your clips - resize, dissolve, etc don't require rendering until export. You need to check the Render All menu (opt-r) under Sequence has everything checked...
Patrick

"Export as Quicktime Movie" -- won't play on other computers

When I use the "Export as Quicktime Movie" option and try to play it back on a Mac without FCP installed, it is missing components and won't play back in Quicktime Player. Of course, I can export with various compressions and then it's fine, but sometimes I want that big "original" file. Any thoughts? Thanks!
Message was edited by: elisenew

You do need the codec you are exporting to installed in the other machine if you wish to play the exported file. A variety of codecs are available only with FCP installed.
A couple of possible solutions are a very high res H.264 or Download [ProRes decoder|http://support.apple.com/downloads/AppleProRes_QuickTime_Decoder_1_0_forMac] to share a prores file between machines.

File type for export as quicktime movie

I thought I read here that "Export as Quicktime Movie" produces a .mov file (although without the extension). I'm using Brightcove to host our videos, and their publishpod says it accepts .mov files, but doesn't seem to work with the file from FCE. Is it really a .mov? Or do I need to export using Quicktime Conversion (and burn up lots more time in the process?)

Thanks...
I did search the forum and nothing addressed my specific issue. Sorry if I didn't phrase my question clearly.
Anyway, I suspect the problem is that the Brightcove software does not work well with the Apple Intermediate Codec. I had no problem with a .mov exported with H.264 compression. This adds extra time to my workflow, but I suspect it will be a necessary evil.

FCP export to "QuickTime Movie" distorts aspect ratio of all text, displays video correctly.

Similar Messages

Maybe you are looking for