FCP Problem with Firewire output to external monitor and speaker ???Help

i have a g5 powermac. the problem is when using Final cut pro 4hd. when i output my work through firewire to my external monitor and speaker i have a problem with the audio signal. Theres feedback/noise/hiss from the speakers. The firewire connects to DSR-11 vtr deck which feeds my monitor and speakers. it only happens when in FCP is set to A/V firewire output. does not happen if Video output is not set to firewire.
I Diagnosis is that it is not my dsr-11 deck or firewire i've ruled those out. The problem is either FCP software or Hardware problem with my G5
Does anyone have a similar problem. please respone, i will try to answer any respones,
Thanks
powermac g5 powermac

CaptM
From the firewire that feeds the dsr-11. on the output, i use s-video cable to my monitor (sony pvm-14l) and High Quality rca cables thet feed the audio to the Roland Speakers.
I've changed all wires and still have audio problem. I,ve changed my Dsr-11 deck to my camcorder and still have the problem.
If any of u guys use FCP The problem happens When I select view> external Monitor > and select firewire for Audio/ and video. I have never changed my editing habits, something just went wrong with the signal, I think its a Hardware problem with the firewire connection. I'm Going to have to bring this to a Apple Service Center In my local area one day.

Similar Messages

T420 (4180-1G8): Problem with VGA output to external monitor

Hello,
I am trying to get the VGA output to an external monitor to work.
I am connected to my monitor directly using a standard VGA cable.
I am trying to enable primary display to the external monitor: I only get a black screen. The monitor says it is not receiving a signal.
When I try to clone or extend the display: same results.
Here is my setup:
Monitor: Iiyama ProLite E2710HDS
Operating System: Windows 7 Professional 64bit w/ Service Pack 1
Laptop: Thinkpad T420 (4180-1G8)
Graphics Adapter Info:
Intel(R) HD Graphics 3000
Report Date:            1/11/2012
Report Time[hr:mm:ss]:        10:27:8
Driver Version:            8.15.10.2538
Operating System:        Windows 7 Service Pack 1(6.1.7601)
Default Language:        English (United States)
DirectX* Version:        10.1
Physical Memory:        3979 MB
Minimum Graphics Memory:    64 MB
Maximum Graphics Memory:    1696 MB
Graphics Memory in Use:        88 MB
Processor:            Intel64 Family 6 Model 42 Stepping 7
Processor Speed:        2491 MHz
Vendor ID:            8086
Device ID:            0126
Device Revision:        09
*   Processor Graphics Information   *
Processor Graphics in Use:        Intel(R) HD Graphics 3000
Video BIOS:            2089.0
Current Graphics Mode:        1600 by 900
*   Devices Connected to the Graphics Accelerator   *
Active Notebook Displays: 1
    *    Built-in Display    *
Monitor Name:            ThinkPad Display 1600x900
Display Type:            Digital
Gamma Value:            2.2
DDC2 Protocol:            Supported
Maximum Image Size:
Horizontal:            12.20 inches
Vertical:            06.69 inches
Monitor Supported Modes:
1600 by 900 (50 Hz)
1600 by 900 (60 Hz)
Display Power Management Support:
Standby Mode:            Supported
Suspend Mode:            Supported
Active Off Mode:        Supported
Raw EDID:
00 FF FF FF FF FF FF 00 30 AE A1 40 00 00 00 00
01 14 01 03 80 1F 11 78 EA CC CE 99 58 50 8E 26
24 4B 53 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 F8 2A 40 9A 61 84 0C 30 40 2A
33 00 35 AE 10 00 00 18 CF 23 40 9A 61 84 0C 30
40 2A 33 00 35 AE 10 00 00 18 00 00 00 0F 00 A9
09 32 A9 09 32 19 09 00 06 AF 56 31 00 00 00 FE
00 42 31 34 30 52 57 30 32 20 56 31 20 0A 00 7B
Regards,
Stephane B.
Note: the external monitor works fine with my desktop computer and with a T400 laptop.
Solved!
Go to Solution.

Follow-up:
I have tried the latest "generic" Intel driver after completely uninstalling the device driver from device manager: without success.
I have tried another monitor from a different manufacturer: no luck.
To eliminate the device driver as a possible cause, I tried booting from an Unbuntu boot CD: no luck.
I have enabled boot display on the VGA port in the BIOS: screen remains black.
I am suspecting that the VGA port on my brand new Lenovo Thinkpad T420 is simply not working at all.
I have opened a call with my hardware support.
Regards,
Stephane B.

Anyone having problems with Safari on an external monitor with Lion?

I have an iMac with external second monitor. Upgrade to Lion. Aside from it being terribly slow, and having typing problems (where first letter appears 4th or 5th when beginning to type), I've noticed the following:
On iMac monitor, everything works fine.
On the external monitor, it's often impossible to fill in a form. Drag Safari over to the main monitor - no problem. Drag it back - still can't complete a form.
Another example: Netflix. Plays on either monitor. However, stopping and starting a movie with the mouse doesn't work. With the space bar, it does.
Overall terribly disappointed in what Lion has done to my computer.

What exact problems are you having? I have been having intermittent problem with mine. Sometimes certain sites will not connect. I get a message that the server stopped responding. I open Firefox and it connects fine.
-Bmer
Mac Owners Support Group - Join us @ MacOSG.com
  Mac611 Mobile Mac Support - about.Mac611.com
   iTunes:MacOSG Podcast | YouTube.MacOSG.com
                   An Apple User Group 
Have an iPhone or iPod touch? Enter Mac611.com in Safari on it for 'mobile Mac support.'

Problem with fullscreen youtubevideo on external monitor

I have an external monitor conneted to my macbook, but when i play videos fullscreen on the monitor, the finderbar, dockbar and mouse disappears, how do i fix this?
(OS X 10.8.4)

Try this:
- render the sequence (alt-R), and mixdown audio (alt-cmd-R)
- make sure the canvas zoom is set to Fit to Window
Piero

What do you need to get video output to external monitor

Hello,
I'm fairly new to Color and have read a few posts that color can't be viewed by firewire to an external monitor. Basically what I have right now for external viewing in FCP is a JVC SR-VS30 Mini DV NTSC deck with firewire connected to my computer. From the deck it goes to a small TV set and a Sony Trinitron PVM color video monitor. What do I need extra to be able to see my color correction in Color on an external monitor. BTW in Color currently the Video Output tab in Setup>User Prefs is grayed out showing Disabled. I suppose that when I get whatever I need to see Color on an external monitor that this tab would NOT be grayed out or would I have to set some other settings.
Thanks.

Well, you can waste a lot of time and money trying to get your old iron up to speed but the sad fact is, even though it may work with Color, it will most likely end in a less than satisfactory experience all around. You need to determine if your G5 has PCI, PCI-x or PCIe slots and then purchase the appropriate cards.
However, Final Cut Studio 2 is optimized for the Intel processors. You will see users here and there using the newest models G5 with great success but quite honestly, you need a Mac Pro.
Or just purchase the Aja IO/HD which is a firewire 800 interface and the only firewire device that will preview externally Color.

Output to external monitor fail after few seconds

hi
i upgraded my x61+X6 utlrabse docking st. to X200 with X200 ultrabase docking station.
i have a DELL 20 inch LCD as my external mointor.
the docking statition is connected using a USB-KVM to the external monitor.
with the X61 i manage to see the external monitor
with the X200 i see the external monitor and after10 sec it goes down.
few more related facts:
1)i can see in the Windows Vista HW and Driver setting that the DELL SP2008 screen is registeredbut than after10 sec it disaapear and screen goes off.
2) when i goes to Intel Graphics Media Accelerator the only option is the choose only laptop display and no external one is shown.when i swith with the kvm to another computer (actually disconnecting the external monitor) and goes back to X200 i can see for 10 sec the external monitor.
any idea what is the problem ?
Thanks

I am seeing the same behavior with a T420s and a Trendnet TK-409 KVM. The KVM works with all other laptops and desktops I have connected to it so this is surprising. Any help or suggestions would be highly appreciated. Thank you.

Satellite Pro U300: DVD issue - error: cannot output to external monitor

Hi,
I was having problems playing a dvd on my U300.
Basically the software would load but when I tried to play the dvd it said "cannot output to external monitor".
Having gone through all options I could not find anything to stop this happening. I then downloaded the latest software from the toshiba site.
dvdpl-20070807102909.zip
I resintalled this but got the same error message.
I then uninstalled the software and tried to reinstall but now it just produces an error mesaage saying it cannot intsall the software on this computer.
How can I reinstall this?
Regards,
Mark

I presume you have received the Toshiba Recovery CD. Am I right?
On this CD you can find the Toshiba image file. This image contains the Vista OS, Toshiba drivers, tools and additional software.
But note; you cannot install only a single program. To reinstall a application from the Recovery CD you have to format the HDD and have to reinstall the whole OS using the Recovery CD.
As Gipsyman said, the Toshiba driver page contains update and the original preinstalled software is needed.

Using the GT70 with external monitor and lid closed

I wasn't sure where to post this question.
I have several laptops and use external monitors. I close the lid on the laptops and the display continues to work.
On the GT70, the system shuts down. It won't allow me to use the external keyboard and mouse or display the session.
Any suggestions if there is a configuration option to allow the GT70 to continue to function with external monitor and lid closed.

Yup. This is a windows setting. You need to go into your control panel -> power options -> "Choose when the computer sleeps" and "Choose what closing the lid does"
That should solve the problem. I currently have my GT70 hooked up to a 42" TV and I can close the lid and it stays on and the TV continues displaying as well. No problems. =]

MacBook Pro with external monitor and keyboard.

Hello, everyone.
I've tried to find the answer for this question but haven't found a clear answer with my Google search.
My older Powerbook G4 will not allow me to work with an external monitor and keyboard with the screen in a closed position. I am about to purchase a new MacBook Pro and would like to be able to use it at home with a larger monitor and keyboard but with the lid closed and its built-in screen turned off. Can this be done ?
How can a MacBook Pro be used (turned-on) with external monitor and keyboard while the lid is closed and the its screen is off ?
Thank you in advance for your answers.
Joseph

Hi Niel,
I have the same problem with my MacBook and I followed the instructions you posted. My issue is that when the computer wakes up after clicking the buttons on the keyboard it then quickly goes back to sleep. I can't seem to keep it awake when the lid is closed. I've been searching for an answer without any luck. Any idea how to solve this problem?
Thanks!
P.S. After I finished posting this message I figured out my problem. While fiddling with my computer and monitor, I inadvertently disconnected the power. After reconnecting the power, I was able to wake my computer and keep it awake. A note to other people having this issue: the computer must be connected to a power outlet to run in closed mode.
Message was edited by: qwertyphd

Mac Pro Early 2008 problems with firewire 400 drives

I am having some sporadic problems with firewire 400 drives and am trying to figure out my best options going forward. System 10.5.2 has hung on me twice in the first week of use, and each time I noticed from console there were some problems accessing one or more of these drives (even though I wasn't doing any reads/writes to/from them). Just before one of the crashes, Disk Utility also had problems "seeing" these drives. My external firewire drives are:
Maxtor OneTouch III 750GB
Acomdata enclosure/Seagate 400GB
LaCie d2/160GB
LaCie w/Lightscribe DVD
I have this "cobbled" arrangement because I just upgraded from an eMac and needed these drives to manage video files, audio files, photos, etc. While I'd love to go out and buy new internals to install in my spare bays, and migrate the data to them, I will have to do that in stages as my budget is tapped out at the moment. My MacPro is the base version of the early 2008 units, with 300GB internal.
In the interim, is it worth troubleshooting firmware updates for these externals, or am I destined to continue to have firewire problems? Is there a straight-forward/inexpensive way to remove these drives from enclosures/install in drive bays with an adaptor? I believe the external hard drives are all ATA type drives.
Thanks in advance for any counsel.

I would assume that the Maxtor may be SATA. Does it have an eSATA port? Also, there were a lot of threads (in OS X Leopard forum) about those OneTouch units. Same can be said for LaCie problems.
Yes, check for firmware and configuration. In some cases, and what I do with any new OS, is to reformat all drives - gradually. Given the age of the eMac I'd guess firmware is out of date, and that the drives are formatted some time ago. While you don't have to use GUID, it is a good idea eventually, or just reformat a drive.
Don't forget to test your drives with Disk Warrior (4.1) also.
750GB WD Caviar is $139 SATA.
http://eshop.macsales.com/Specials/XLR8YourMac.cfm?Criteria=&sort=&man=Western%2 0Digital
Are you using daisy chains? you have one FW bus shared by front and back ports. Do you have any on FW800 or using FW400 to FW800 adapter cable? PCI Express FW400 card might even help a little.
Never had trouble with OWC enclosures:
http://www.macsales.com/firewire/

Thinkpad T420 with Dock 4338 Dual External Monitors won't work

Hey Everyone,
I recently purchased a T420 with Dock Model 4338 and am trying to connect two external monitors. I want to have my desktop visible on my primary monitor with laptop closed and that desktop extended onto my second external monitors. Both external monitors are Dell 19", one is being ran through the VGA port on the dock and the other is a VGA cord that I put a VGA to DVI-D adapter on to run off of one of the DVI Ports on the dock. I can get my desktop to display on the main external monitor, and everything detects the other monitor fine, but the extended monitor remains black. The screen is on, and recognized as the button light on the monitor is green not yellow and i can scroll my mouse over to that window and i lose the mouse so it's extending just not visible. I have made sure that both monitors work by checking each individually in the VGA port and they are operational, but the DVI-D port doesn't seem to work on my second monitor.
I have done some pretty extensive searching and can't seem to get this to work. At my job I have a T430 with the same dock and dual monitor setup that took no time and works great. Does the T420 just not support this?
All help is appreciated.
Thank you all,
NickG
Solved!
Go to Solution.

DVI-D don't support passive dvi to VGA adapter. You are better off with a displayport to VGA adapter, as they are cheaper then a dvi-d to VGA converter.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Problem with Excel output format

Hi Guys,
I am creating a report in XML Publisher (not standalone). I am facing some problems could anyone please help me to figure out the issues.
Is it possible to have all three output format (PDF, HTML & EXCEL) exact (same aligned) only by creating a single RTF Template? I am facing the problem with Excel output format the output format of excel is taking excels cell formatting.
Example Numeric fields --> Right Aligned, text fields --> Left Aligned
One more issue with excel is -ve(negative) values are getting displayed in red and in brackets like ($13) (with red color).
Our client want excel output on priority.
Is there any limitation for excel output format of reports?
It is very urgent for us please help.
Any help would be highly appreciated.
Thanks,
Pragati
Edited by: user11237443 on Aug 27, 2009 1:22 AM

Hi Mahi,
Thanks for your response. But i could not understand how can we write wrapper program could you please give some light on this or provide some link it would be helpful for me:-)
I have read that blog for excel limitations but i have more question?
1) What about the negative values?
if any field is displaying negative amount then excel not displaying right value for that:(
2)How can we align header or data?
Do XMLP with EBS provide any solution for formatting in excel?
3) If for the alignment of numeric value we concatenate them with any special character then how can we perform calculation that field?
Here are so many formatting issues do we need to write any code in xml for that?
Please help.
Many Thanks,
Pragati

Have a problem with my MacBook Pro.5,3 and monitor. Intermittently, the desk top screen becomes broken up into vertical sections, which appear in the wrong order, creating a haphazard picture. The Apple icon, usually at top left corner, appears in to

have a problem with my MacBook Pro.5,3 and monitor. Intermittently, the desk top screen becomes broken up into vertical sections, which appear in the wrong order, creating a haphazard picture.
The Apple icon, usually at top left corner, appears in top right corner in a strip including all that left hand. When the computer is restarted, the screen goes back to normal. But I have to move the mouse to the far left of the screen and then up until it reappears on the far right hand side of the screen so that I can hit shut down button.
It seems to happen randomly though always on desk top and sometimes when I move mouse and computer switches on from rest mode. My large flat screen is relatively new.
The video card on this computer, which is approximately two years old, is Nvidia FeForce 9400M.
Any help would be welcome as my usual source of assistance is not available and I am not well versed in workings of the Mac although I have used one for many years.

That sounds like a Hardware problem.
You may be able to confirm that with Apple Hardware Test, or make an appointmenst for a free Genius Bar evaluation.

Using the MacBook Pro with external Monitor and Keyboard

This may be a dumb question, but here it goes anyway:
Can I use the MacBook Pro with an external monitor and a bluetooth keyboard and mouse without having it opened all of the time ?
I am planning to buy a MacBook for my wife and most of the time she will be using it at her home office.
I don't want her to use the computer opened all of the time when she is actually looking at the separate screen and using a separate keyboard. Having the laptop opened will only accumulate dust and reduce the lifetime of the built in screen.
What I would actually need is a kind of "docking station", but Apple doesn't make that - I know.
So can the MacBook at least be operated without the internal screen powered on while it is closed?
Thanks for your help
Martin
Message was edited by: mdopp

Yes - it's called clamshell mode:
http://support.apple.com/kb/HT3131

Problem with RTPExport output video files

Hi, I have a problem with RTPExport output video files. One side streams H263/RTP(AVTransmit2.java) and other write this steam to a file by RTPExport.java. When network conditions are ideal, output video file has same fps and same number of frames like original file. Problem occures, when theres packet lost in network, then output file has different fps,and also has less frames like original video(because it didnt write missing frames to file, and thats why it get shorter). Pls how can I achieve output file that will have the same fps like original one? How to write to file an identical copy of what I can see while receiveing video with AVReceive2.java? Its there a way to modifi rtpexport or avreceiver to do this? Thanks a lot!

Trubka wrote:
When network conditions are ideal, output video file has same fps and same number of frames like original file. Problem occures, when theres packet lost in network, then output file has different fps,and also has less frames like original video(because it didnt write missing frames to file, and thats why it get shorter). Okay, first off, the second file is smaller on purpose. RTP intentionally drops packets that are old/out of order in order to make sure real-time video stays as close to real time as it can. This is by design, so there's really nothing that can be done about it.
How to write to file an identical copy of what I can see while receiveing video with AVReceive2.java? Technically speaking, what you're getting in the RTPExport is exactly what you got on the receiving end. Any frames that are dropped during transmission will not be seen by the receiver, nor saved by the receiver.
Pls how can I achieve output file that will have the same fps like original one? I'm not 100% sure that you can, but, you can give the following idea a try. I make no guarentees that it'll work, but it should work for you...
[http://java.sun.com/javase/technologies/desktop/media/jmf/2.1.1/solutions/RTPConnector.html]
That example is an example of a "custom transport layer" for RTP connections. Essentially, it's some code that's handed the RTP packets on the transmission end, and it's expected to deliver those RTP packets on the other end. And it doesn't care about how they get from A to B, only that they do.
If you were to replace the UDP socket in that example with a TCP socket, you would be guarenteed not to drop packets due to network reasons. Every RTP packet you were handed by the transmitter, you would then hand to the receiver. There is no guarentee that none of the packets would be cast away as "old" by the RTP protocol itself, but there's also no guarentee any of them would be. It's a crap-shoot at best, but it's certainly worth a try.

FCP Problem with Firewire output to external monitor and speaker ???Help

Similar Messages

Maybe you are looking for