FCP X not transcoding on import.

Even though I have the proper preferences set, no optimized media is being created. After looking at the drive where the files should be created, I am getting alias. What is going on?
Best.
Tom

Hi Thomas,
I know you say that you have your preferences set correctly, but have you checked 'Copy files to Final Cut Events folder' in the 'Import' tab of Preferences?
If this option is not selected, then only references (aliases) to the original media are added to the Events folder.
Regards,
Acros-Krik

Similar Messages

Not able to import .motn files into FCP

For some reason I'm not able to import .motn files into FCP. While in FCP, I use "send to motion" and uncheck the embed box. After motion opens and I add my motion content, I get the following error when trying to import the .motn file back into FCP "File Error: 1 files(s) recognized, 0 access denied, 1 unknown". What is strange is that I'm able to create another test FCP project with different media, and everything works fine. All tests and media are done on the same drive.
I'm using the latest updates of everything FCP 5.0.4 and motion 2.0.1
Any ideas anybody?
Thanks!
G5 Mac OS X (10.4.6)

Check the frame rate - that can sometimes interfere...
Patrick

Encore CS4 is transcoding compliant Blu-Ray audio assets when set to 'Do not transcode'

Hi there,
I have a Blu-Ray concert video project consisting of 3-menus, 4-sequentially linked timelines (intro-1, intro-2, main concert timeline, and credits).
All audio assets consist of 96k/24-bit WAV files from the same professionally rendered mastered audio source.
Here's the issue:
When importing my 96k/24-bit audio assets in Encore CS4, they all show as Blu-Ray compliant and maintain the 'Do not transcode' property in the assets menu.
However, after rendering the project to Blu-Ray I immediately noticed that the main concert timeline (2-hrs 10-min) had been transcoded down to 48k/16-bit while the other smaller intro/credits timelines had rendered correctly and were playing back at the desired 96k.24-bit rate.
In order to eliminate possible issues with the main timeline's audio file source, I created a smaller main timeline (35-min) using the exact same audio source files and lo & behold - the main timeline was not down-transcoded and is playing back at the desired 96k/24-bit rate.
I'm wondering if there is a non-documented limitation in rendering audio files over a certain size as my main timeline is made up of 2-total WAV files of 2.2Gb each.
I have the ability to import a single AIFF file at 4.4GB for the main timeline - but for some reason CS4 does not recognize AIFF files as Blu-Ray compliant and will show the transcode setting as 'Automatic'.
Imported AIFF files always showed as 'Do not transcode' in the Blu-Ray assets menu in Encore CS3 (even though there is a documented bug which prevents rendering AIFF audio to Blu-Ray and I would have to convert to WAV files and re-import anyway in CS3).
My next step is to try splitting the main timeline into shorter chunks, but this is not the direction I want to go in.
Any help would be greatly appreciated!
-Cheers

Ok, solved my own problem - solution below for those with similar issues.
1. My audio timelines exported from Final Cut Pro as AIFF are actually 'AIFC' which is technically not Blu-Ray compliant, thus Encore will need to transcode. Unfortunately - Encore has no quality preset settings for dealing with PCM audio transcodes higher than 48k/16-bit (why not?). Encore CS4 will happily pass 96k/24-bit through to a Blu-Ray build without transcoding if the supplied file is true AIFF (not-AIFC) and/or similarly compliant WAV files.
2. My main Encore timeline consisted of 2-WAV files at 2.2Gb each placed in a single Encore timeline due to the total audio being over 4GB thus requiring me to split the source audio files in half in order to stay under the 4GB limit for WAV files, and also because I had to export the FCP audio timeline using Compressor in order to generate Blu-Ray compliant audio files (non-AIFC). Also - (possible bug?) if Encore has 2-separate audio files in the same timeline it will transcode the audio to the current project's default audio settings (48k/16-bit in my case) - even though the assets are showing as 'Do not transcode' in the asset menu for Blu-Ray. It clearly states in the Encore CS4 manual that imported WAV files at 96k/24-bit will not be transcoded - but it appears in this case when 2-audio files are placed in the same timeline that it will transcode with no warning - bothersome to say the least.
I suppose the alternative is to work with a lossless audio format which supports files larger than 4GB - which would only require a single audio file for a single Encore timeline, but other than DTS Master Audio (not available on this project) I'm not sure what audio format would work in Encore to support 96k/24-bit audio files larger than 4GB.
If anyone knows - drop some knowledge!
-Cheers

FCP X not linking to optimized media

For some reason, FCP is not linking to optimized media- none of it, ever. My footage was transcoded on import and an optimized media folder created. I have everything in the Library bundle- both orignal media and optimized media folders are inside. I know FCP is playing the original media because 'reveal to finder' points to original clips. In addition, inspector shows H264 codec. What's the point of optimizing media if FCP doesn't point to it? How can I get FCP to utilize the transcoded clips in the optimized media folder?
FCP 10.1

AVCHD is basically H.264
This is an extract from the AVCHD article in Wikipedia . . . .
For video compression, AVCHD uses the MPEG-4 AVC/H.264 standard, supporting a variety of standard, high definition, and stereoscopic (3D) video resolutions. For audio compression, it supports both Dolby AC-3 (Dolby Digital) and uncompressed linear PCMaudio. Stereo and multichannel surround (5.1) are both supported.
Message was edited by: Ian R. Brown

Encore changes lower filed to upper in dvd header when working with m2p assetand not transcoding

i have full compatible m2p and audio files that doesn't need transcoding. i like to make subtitles by importing text script with encore 1.5. the problem is:
my m2p file is lower filed and even if encore doesn't encode the original m2p file (not trnascode) the output video seems to have upper field tag in dvd header. since it is not re-encoded (i know it for sure, also authoring is done very quick) the video is still lower field but encore marks it as if it was upper field. so the dvd player tries to play lower field video as if it were upper filed and i see interlacing problem on the video.
even i don't re-encode the video i tried to check the field dominance in pre-rendering options and it is set lower field also.
while making a new project encore doesn't ask you whether your project is lower or upper field. and there is no menu i can adjust it_ so what encore renders is soft subtitle picture files.
i think the problem is just that encore write as default upper field to the header for not transcoded videos. if this is the case it is a BIG bug. does anyone know a soluiton
orton

I used the standard export definitions from Premiere CS5.5 (windows media / download the pal-widescreen source for high quality = 720x576 pixel, codec Windows Media Video 9, 25 fps, pixel D1/DV Pal widescreen 16:9) for instance.
But it doesn´t matter which template I use, all other versions (from HDTV 1080p to HDTV 720p) had the same result.
Avis make no problems, but as soon as I choose the files, Premiere exported as wmv, Encore cuts off the upper half... :-(
I understand how video formats work, but I don´t have any idea why Encore is unable to import the full picture...
I also checked if there are any updates available, but the updater declared all installed versions as up to date...
By the way, Ahead Nero Vision has no problems with the import, but since I own Encore, I would prefer to use the Adobe software.

FCP 4.5 crashes when importing long clips

After upgrading to a new computer (PowerMac G5 2.7 GHz), my FCP 4.5 has trouble importing DV footage from my Canon GL-1 camera. The program hangs after about 4 minutes of importing a single clip. I have seen that this issue may be related to upgrading QuickTime (using 7.3.0), but still not sure that this is the problem.
Any ideas would be welcome.
I have purchased FCS 2, so I can upgrade, but I was waiting until I complete an unfinished FCP 4.5 project. If upgrading would allow be to still read these 4.5 files and complete it that way, I would. Any ideas would be welcome.
Dean

That might be the issue. WHich is why it is never wise to upgrade a working system. The OPTIMAL system setup for FCP 4.5 is Mac OS 10.3.9 and QT 6.5...although QT 7.1.6 works just fine. When you start upgrading things beyond that, you risk things not working right. What did an upgrade to QT 7.3 get you? Nothing really.
Unfortunately to get BACK to a working version of your system, you'd need to do an Archive and install of your OS...yes, time consuming....sorry.
BUT, you can upgrade to FCS2 and continue to work on those projects. They will convert just fine. I would suggest cloning your system drive first, so you have something to fall back on. ALthough the system isn't working so...you really don't have anything to lose.
Shane

Transcoding and importing

Hi
I have a one minute video clip, just a logo rotating, no sound. Uncompressed avi size is 2GB. Now how long does it usually take to transcode and import such a file? I can see that it transcodes it just fine, but when Encore tries to imports it, my PC can do that for like 2 hours and nothing happens, so I close the program. Where's the problem?
Win XP SP2
P4 3GHz
1GB RAM

A MOV file should import just fine - and it won't even transcode on import unless it's at 24p.
Is there any way you can give me access to one of these files so I can have a look here?
We also use Flash, but it can do some odd things with AVI files - were all the clips on the main timeline, and not hidden?
I have just had a quick talk with our resident Flash-Head, and she tells me it's not as straightforward as it could be.
After Effects usually produces compliant files with little trouble. Did you use the DV settings?
(Render Composition, and where it says "Best Settings" there is a little arrow. Click on this, and choose DV settings. Then, this is a hyperlink that can be clicked on to set the detailed options.
In the output module there are also a lot of choices accessed from the little black arrow.)
FWIW, with Encore 2 - as long as you have the production studio bundle installed, you can use the Adobe Dynamic link to import from AE compositions.
Even with no PS bundle installed, you should still be able to import a discrete movie:
"Composition/Make Movie"
When the render queue opens, click on output module and select "Project Link" from the embed menu.
What is the spec of your machine - uncompressed AVI files can reallt slow things down, and may not even work at all in Encore - which really expects to see DV type files.

FCP 4 HD won´t import mov files

Hi,
I exported a clip with the QT conversion option and added a few of the menu´s special effects (lens flare, sepia, etc.). The file opens all right with QT, but when I try to import it to FCP, I get an error message. This also happens if I try to open the file from my desktop using the "Open with..." option and select FCP.
I had no problem importing the file to iMovie, so I am really puzzled about this...

File error: 1 file(s) recognized, 0 access denied, 1 unknown
I get that message. I wanted to know if you found a solution. I am using Final Cut 4.5
I just started getting error messages whenever I try to import a file. Whatever file I choose gets a window that says:
"File error: 1 file(s) recognized, 0 access denied, 1 unknown"
Never had a problem with Final Cut before. I'm baffled. Please help. I already tried trashing the preferences.
I am not able to import any type of file at all. Quick time movies, audio, livetype, etc. I have been able to import all these files for several months. Now for no apparent reason I am unable to import files.
I have looked at different discussions of this same problem. There seems to be an access problem. The files are valid. They will open with Quicktime. They will import into iMovie.
So the problem seems to be that FCP cannot access the files.
Anyone know the solution?

FCP 7.01 crashes when importing tape

When importing (Control-8) a DV-Tape (HDV), I see the import window as long as I press the switch "Direct". The program crashes immediately, even after re-installing the complete program. I don´t know what else I can do. I had no problems with FC Express before, but now with the full version I´m not able to import my videos at all...
I ereased the prefernece files as described somewhere else, but this did not affect anything.
Since I have to edit a very important video until Sunday evening, I need an urgent help!

Hi Rainer, you are obviously running FCP in German. The button marked "Direkt" on your system is marked "Now" on a FCP system that runs in English.
nsTODimporter is a QuickTime component. It is located at Hard Drive/Library/QuickTime and is installed by cameras that record in the .tod format which is a variation of MPEG 2 developed by JVC.
Before you resort to a clean install, remove that component. You will need an Adminstrator password to fully remove it.
I now will format C
That's windows terminology. Mac hard drives have names.

Not able to import mov files?

Hi!
I have a problem with importing mov files into FCP and already posted in the Quick Time Forum, because I think it's a codec issue. May I link to the Quick Time discussion? http://discussions.apple.com/thread.jspa?threadID=2326392&tstart=0
Hope you guys have an idea!
Thanks!

From your post on the QuickTime forum:
"I use MacOS 10.6.2 with my old FinalCut Pro HD 4.5"
Your version of FCP is not compatible with your current Intel based hardware and version of Mac OS X.
It will install and launch but you can expect very unpredictable behaviour and crashes.
To have this work correctly, you should upgrade to at least Final Cut Studio 2. Look on Amazon or similar for FCS 2 -it has been discontinued, or just go for the current FCS 3 upgrade.

Lightroom 5.6 crashing, not able to import or back up changes

I have been having issues with Lightroom 5.6 for few days now. I have been working from this Lightroom install for a year now problem free. The problem seems to happen when I try to import pictures. At first I thought it was my SD card but I copied the pictures to my desktop and was not able to import from the file on my desktop. It will start to download a few out of 400 and stop at 2 or 3 pictures then freeze. A message pops up that says "Lightroom encountered a problem and needs to quit" When i try to open Lightroom again I will get a message that says "The last time Lightroom ran, it shut down prematurely due to a problem reading the catalog. Lightroom must now check the catalog before proceeding." It will proceed to check integrity of the catalog then another message pops up saying it was repaired successfully. When I try to open, same stuff happens all over again.
I have not moved any files around through the external hard drive and there are no images in the catalog that are "missing." So I'm a little confused as to why Lightroom suddenly keeps crashing.
I am able to export images from the same catalog, I am able to edit pictures as I normally would,but I am unable to Back up the changes or import new files. I tried working from a different external hard drive and the same thing happens.
Please help!!

Are you able to import 450D raw files into LR5.5via USB connection and are you on Windows 7/8?
I agree with your observations concerning SD vs CF card fragility, but they also have a limited number of insertions before failure.
http://en.wikipedia.org/wiki/USB#Durability
The newer Micro-USB receptacles are designed for up to 10,000 cycles of insertion and removal between the receptacle and plug, compared to 1,500 for the standard USB and 5,000 for the Mini-USB receptacle. This is accomplished by adding a locking device and by moving the leaf-spring connector from the jack to the plug, so that the most-stressed part is on the cable side of the connection. This change was made so that the connector on the less expensive cable would bear the most wear instead of the more expensive micro-USB device.
All my Canon cameras have micro-USB connectors. With one (1) insertion and removal per day that equals 10,000 days, or about 27 years before end-of-life! SD and CF cards are also rated at ~10,000 insertion and removals, but more prone to damage from static electricity and handling due to the exposed contacts and fragility of CF card sockets.
So there's no real advantage from the camera wear perspective to using a card reader. I'd say use whatever method is easiest for your workflow, but handle memory cards with care and avoid exposing them to static discharge. Ground yourself to something metal before removing memory cards and inserting them into the card reader, especially in cold Winter months.
BTW- I helped design one of the first semiconductor DRAM memory systems back in 1970. We killed more memory chips than I care to count before we discovered they were easily damaged by static electricity. Today's ICs have built-in protection, but you can still damage them with a big enough static ZAP!

Class not found in import

I am new to the Java technology and am running into some problems getting started. Initially, I was getting the following error: Class javax.swing.JOptionPane not found in import. After realizing that I needed to unzip the src.zip file, I did so. I tried compiling again and got the same message. I came across a website that talked about setting the CLASSPATH. So I set the class path like so: set CLASSPATH=.;C:\;c:\j2sdk1.4.2_04\src;. Finally! I got passed the first error. However, what followed was quite depressing. 50 Errors! Looks like the compiler can not find any class I import that starts with "sun.". I looked where I can see the javax folder and there is no sun folder. Did I miss something in the installation? Is there a workaround for this? I thought I read somewhere that you shouldn't import sun.* classes, but what happens when it is in the delivered packages? TIA Ryan

Well to start off... The file Src.zip only contains source files nothing compiled so it useless unless you want to look at the source code, the Java Class files are in a "Jar" file...
Set your (system) path to c:\j2sdk1.4.2_04\bin
your ClassPath should only point to the new class files that you created...
( I don't even have the ClassPath set on my computer)
And this link deals with setting the classpath...
http://java.sun.com/j2se/1.4.2/docs/tooldocs/windows/classpath.html
That should take care of it... Here are some links for you to check out...
The Java Tutorial
http://java.sun.com/docs/books/tutorial/index.html
Essentials of the Java Programming Language: A Hands-On Guide, Part 1 and 2
http://java.sun.com/developer/onlineTraining/Programming/BasicJava1/
http://java.sun.com/developer/onlineTraining/Programming/BasicJava2/
Language Essentials Short Course
http://java.sun.com/developer/onlineTraining/JavaIntro/contents.html
Tutorial Index
http://java.sun.com/developer/onlineTraining/index.html
- MaxxDmg...
- ' He who never sleeps... '

Excise tab is not appearing in Import of STO material-MIGO display

Hi Guru's,
Excise tab is not appearing in Import of STO material-MIGO display.
Find the Process steps below.
1)Stock transfer order using NB document type-(Company codes are different)
2)VL10B
3)VL02N-PGI
4)Customs Invoice in Indian rupees.
5)Capture excise invoice-J1IEX(Capture excise invoice w.r.t PO not STO)
6)Goods receipt with Reference excise invoice(Excise tab appearing while posting goods) MIGO
7)Post Excise invoice--Accounting entries everything is correct.
After posting the MIGO when we display Material document in MIGO, excaise tab is not appearing for this scenario only.Rest of all Excise tab appearing.
Note:In J1IEX display of excise invoice in Reference document2 field Material document should be there but not showing its empty field.
Thanks,
VR
Edited by: get_vr on Feb 10, 2010 9:08 AM

Excise captured & posted using J1IEX using 2 step procedure won't appear in MIGO screen.
Display excise invoice using J1IEX(using vendor excise inv. no. or internal document no)
Only excise captured & posted in MIGO(Single step) will be appear in display of MIGO screeen.
Check SAP Note 952287 - CIN: Limited Functionalities in Country Version India -CIN -Q.no.5
5. Incoming Excise Invoice capture at Blocked stock 103 is not
supported in CIN.
The capture of incoming excise invoice is strictly advised to carryout at
unrestricted stock and not at blocked stock(103/105) due to architectural
issues. The capture at blocked stock may cause wrong excise posting.

Excise Accounting document not generated for Imported Asset GR

Dear all,
Excise accounting document is not generated for imported asset goods receipt(MIGO)
but "C" Register part 2 no. is generated,usual accounting document is generated for GR,
Asset is Dr to GR/IR
Process is
1. Create asset purchase order with acct. assignment "A",
2. Customs miro based on p.o.
3. Do GR with excise
4. Post invoice for orginal vendor.
What will be cause of this problem ?
How to solve this issue ?

The above issue may be due to Accout assignmnet -A . Check your accout assignment in spro -mm-purchasing -accout assignment - Asset A - GR Non valuated has Ticked on . If it is ticked on - No Fi entry will happen at the Time of GR .
The reason being , if an FI entry happen for the first time , asset is capitalised . To avoid this GR is made in ur config as this .
rewdzzzz is full if correct
Edited by: manu m on Apr 24, 2010 11:11 AM

I have home sharing on but can't see my library on the computers icon. iTunes does display my purchased tunes but not my own imports.

I have home sharing on in iTunes but can't see my library when I use the computers icon on Apple TV. iTunes does display my purchased tunes but not my own imports.
I can play my own tunes by selecting them on my iMAC and directing them to Apple TV. I think that I should be able to see my entire library on Apple TV shouldn't I?
Am up-to-date with iTunes and using Mavericks OS. I am connecting to Apple TV with an Airport Extreme 802.11n Wi-FI and a brand new Apple TV.
Thanks for any comments,
Roger

Okay, so HomeSharing is not working. Most likely due to a network issue.
Is the ATV and computer running iTunes actually on the same network? Many new routers create seperate networks for the wired and wireless portions of the local network.

FCP X not transcoding on import.

Similar Messages

Maybe you are looking for