FI 6248 Pre Licenced ports(1-12) configuration for Ethernet and FC

Hello UCS Gurus,
I am setting up a new UCS lab with 1 5108 Chassis,pair of FI 6248 and FEX2104.My query about the FI 6248 is that
1) I have 12 pre-licenced Unified ports on my FI 6248 and I need to configure 1-10 for Ethernet and 11th/12th for FC port.,,,,Is it a valid configuration?
2) If yes tomorrow if I buy the licence for the remaining ports 13-32. Can i continue using them as Ethernet and FC ports in alternate.I know
Ethernet ports/FC ports must be grouped together in a block and they should end with even numbered port.
Looking for your response on this....

Hello Padma,
I am stucked at a point of configuration on my lab and need your valuable advice.
I have 8 SFP-H10GB-CU3M and 4 Nos SFP-10G-SR in my BOM.
My confusion is I have to accomodate these SFPs only in my currect environment.I cant wait for the entire process of re-ordering new SFPs.
So I will have to split SFPs between the pair of FIs and IOMs.
So is it that I am short of SFPs? because my understanding says that I will be needing atleast 4 SFPs(Cu) on both FIs.
So for FI1----> 2 SFPs(Cu) for Server ports,2 SFPs(Cu) for Uplink Ethernet ports
for FI2------> 2 SFPs(Cu) for Server ports,2 SFPs(Cu) for Uplink Ethernet ports
That means all my 8 SFP-H10GB-CU3M are exhausted.
I dont have more SFPs to connect to my 2104 IO Modules.Please suggest me some workaround.I am in process of creating a lab so performance and bandwidth is not an issue for me.
Regards
Deepak

Similar Messages

I will be buying the new IMac 27 inch in December. Would like input on the best configuration for photographic and possibly video processing-dream machine!

I will be buying an IMac 27 inch in December. What is the best configuration for photo and possibly video processing.Does one need a Mac Pro? Dream machine!

Just to explain what I just wrote to Laundry Bleach:
Why is there no iDVD on my new Mac?
https://discussions.apple.com/docs/DOC-3673
UPDATE & ADDENDUM:
But even though you can still buy iLife 11 that includes iDVD 7 from Amazon, Apple now make it difficult to install:
Poster jhb21939 posted this in another thread:
“when I attempted to load iDVD into a new iMac. A notice came up on the screen stating that the 'Authorisation Licence' had expired on 25 March this year (2012).
I contacted the Apple support team and eventually, I was told that the Licence had been withdrawn and could no longer be used.”
In other words Apple are now so adamant that we don’t use iDVD that they have tried to make it impossible to install.
In response, Old Toad posted this solution:
“You can still use it one all of your Macs. If you get an invalid certificate message just set your Mac's clock to sometime before early 2011 and run the installer. After you're done reset the time back to the correct time.” He added this comment:
“It began after iDVD and iWeb were discontued and they were dropped from the Apple Store. All I can think of is the certificate was set to expire after a certain time period after the intitial iLife disc was released.
I've been able to use the installer even without setting back the date. I just clicked on the Continue button and it would work as expected. For some it would not continue unless the date was set back.”
The latest anorexic iMacs just announced do not even include a CD drive! Proof positive that Apple virtually prohibit the use of DVDs - although the newly announced Mac Minis do include a Superdrive.
Yet, they still include iMovie! Heaven alone knows or understands what you are supposed to do with your newly edited masterpiece - except make a low quality version for YouTube?

I write digital port by 'DAQmx Configure Logging.vi' and receive TDMS file with 8 boolean channels. How can I write to 1 integer channel?

Hello!
I want to write 1 digital port from PXI-6536 with streaming to TDMS file.
I'm writing by 'DAQmx Configure Logging.vi' and become TDMS file with 8 boolean channels.
How can I write to 1integer channel?
Attachments:
1.JPG ‏27 KB

Hey Atrina,
The actual data stored on disk is just the raw data (that is, a byte per sample in your case). It's really just a matter of how that data is being represented in LabVIEW whenever you read back the TDMS file.
I'm not sure if there is a better way to do this, but here is a way to accomplish what you're wanting:
Read back the TDMS file as a digital waveform. Then there's a conversion function in LabVIEW called DWDT Digital to Binary. This function will convert that set of digital channels into the "port format" that you're wanting. I've attached an example of what I mean.
Note: When looking at this VI, there are a few things that the downgrade process did to the VI that I would not recommend for these TDMS files. It added a 1.0 constant on the TDMS Open function, and it set "disable buffering" on the TDMS Open function to false; you can get rid of both of those constants.
Message Edited by AndrewMc on 01-27-2010 11:21 AM
Thanks,
Andy McRorie
NI R&D
Attachments:
digitalconvert.vi ‏13 KB

PC configuration for Premiere and AE (CC)

Hallo everybody!
I'm an Italian filmaker and I'm going to buy a new workstation but I don't know anything about hardware.
I use Premiere for editing and AE for compositin and motion graphics.
A couple of years ago a friend of mine suggested me this HW configuration:
MSI Z87-G43 z87 4*DDr3 Gen 3.0 sk1150 Vga/Hdmi ATX
Corsair 16GB Kit 2*8GB DDR-1600 CMZ16GX3M2A1600C10 XMS3-12800 serie Vengeance CAS10
Inte Core i7 4770 3.40GHz Cache 6MB Haswell LGA1150 BOX
Samsung MZ-7PD256BW SSD 256GB 840PRO SataIII 540/520MB/s 100K IOPS OE
WesternDigital HDD 1TB Enterprose RE4 64Mb 7200 rpm SataII
Zalman CNPS9900MAXBLUE Silenziosa Led Blue sk1155/1156/1366/775/AMD
Corsair Carbide 300R Middletower No-Power ATX
LG BH16NS40 Bluray Writer 10x 3D
Digitus 3.5" Card reader USB 2.0 port
Logitech keyboard K120 Business
Corsair 750 CX 750watt EPS Pci-E PFC active 80+ Bronze
MSI NVIDIA GeForce GTX770 OC Gaming TF IV 2GB 256bit Dvi/Hdmi/DP PCI-E 3.0
Budget: almost 2000€
Can anyone help me finding a new configuration with the same budget but with new-recent hw components?

Double the RAM to 32 GB at a minimum.
Use a full size case, not a mid-size. You'll get better air circulation and have room for expansion.
Add a couple more hard drives.
Get a 850w gold power supply.

System configuration for ITS and for BSP

Hi,
I´m looking for the parameters needed in a system to connect to an ITS and also to BSP.
I have created one system to be able to connect to ITS and another one to be able con connect to BSP, both of type SAP Load Balancing system.
The system I created to connect to ITS has the following configuration I entered:
Connector:
SAP Client = 350
Internet Transaction Server (ITS)
ITS Description = myDescription
ITS Host Name = myhostname:port
ITS Path = /sap/bc/gui/sap/its/webgui
ITS Protocol = http
Thats it that´s the only configuration I´ve made.
For the BSP system I entered:
Connector:
SAP Client = 800
Web Application Server (Web AS):
Web AS Description = myDescription
Web AS Host Name = myhostname:port
Web AS Path = /sap/bc/bsp/sap
Web AS Protocol = http
My question is this, is this configutation enough?,
It is working fine with this configuration but I´ve seen some other information where they fill more parameters in the connector section, would this extra parameters in the connector section help in any way or they will just simply be ignored?, We will be using Web Dispatcher for both.
does somebody knows the answer? Is there some documentation on this?
Thanx in Advanced!!
Kind Regards,
Gerardo J

The connector properties are only required if you are planning on utilizing the SAP connector to connect to your backend system.
What you have configured so far should suffice for ITS and BSP applications. I hope you have configured the system aliases already.
Have a look at the following links for some additional inputs:
http://wiki.sdn.sap.com/wiki/display/EP/MinimumSettingsforaSystem
http://wiki.sdn.sap.com/wiki/display/EP/HowtoCreateSystemObjectinthePortalforConnectingtoSAPbackend+System
- Shanti

Oracle data guard configuration for primary and standby db_name

I am working on configuring an active data guard for one primary DB and one standby DB. I have a few questions:
1. Can I use different db_name, db_unique_name and instance_name for primary and standby. For example: primary(db_name, db_unique_name and instance_name)=chicago. When I create standby DB with Rman backup and copy of pfile and control file from primary DB or use Grid control to create standby database. Oracle document or Grid control all keep standby db_name=chicago. Only make standby db_unique_name and instance_name=boston. Due to my application system condition, I want to make db_name=boston, not keep it as the same as primary=chicago. Is this valid configuration?
2. In primary datafiles, application system generate datafile name like this: hr_chicago_01.dbf, fn_chicago_01.dbf. When I move datafiles to standby server, if I plan to use db_name=boston for standby DB, can I rename datafiles as
hr_boston_01.dbf, fn_boston_01.dbf? In this way, datafile name match up with db_name. but I will create standby log group and members on primary and standby identically. If in future switching over, DB will not have problems.
3. If I don't use primary DB backup. Instead, I copy all datafiles, redo_log files (no control files) to standby. Then "alter database backup controlfile to trace" from promary and also " create pfile='/xxx/initSTANDBY.ora' from primary. Then modify init.ora and controlfile. Then run control.sql to bring standby DB up. After that, configure redo log shipping and apply with data guard or SQL. Is this a acceptable way to create physical standby DB?
Please advise your comments. Thanks in advance.

I want to make db_name=boston, not keep it as the same as primary=chicago. Is this valid configuration?NO. DB_NAME must be the same ("chicago") at both sites. The Standby will be using a different DB_UNIQUE_NAME (e.g. "boston") and can be using a different Instance name / SID (e.g. "boston").
can I rename datafiles Yes. The database file names can be changed.
If I don't use primary DB backup. Instead, I copy all datafiles, redo_log files (no control files) to standbyWhat is the difference between the first sentence (a backup of the primary) and the second sentence (a copy of the primary) ? A Copy is a backup.
Are you intending to differentiate between an RMAN Backup and a User-Managed (aka "scripted") backup ?
Normally, for DataGuard, tou can use non-RMAN methods to copy the database but there's no value add in this.
You'd still have to setup DataGuard ! (and I wonder if you'd have complications setting up Active DataGuard).
But remember that you MUST create the Standby controlfile from the Primary and copy it over to your Standby -- particularly as you are planning to use DataGuard. This is not created by 'alter database backup controlfile to trace' , but by 'ALTER DATABASE CREATE STANDBY CONTROLFILE AS 'filename''
Hemant K Chitale

R/3 configuration for 0SD_C01 and 2LIS_01_S001

Hi guys,
I have activated the infocube 0SD_C01, the complete flow. I created an infopackage for its infosource 2LIS_01_S001 and made an extraction. I got an error with a delta initialization and with a full upload I got that there is no that data in R/3. Im currently using BI 7.0 and R/3 ECC.
Is there something I need to do first in R/3, some kind of configuration for that datasource? They told me for the datasources 2LIS* used the transaction LBWE, but I dont see 2LIS_01_S001 on that transaction.
What do I need to do in R/3, in order to do extractions? Does someone have a manual for this Datasource/Infosource that would like to share? My email is [email protected]
Thanks a lot
Vic

Hi,
There is no LO datasource , you have to use LIS ..i.e, 2LIS_01_S001.
I hope you know the steps to activate and load data into BW using LIS.
Steps are as follows:
1) Activating LIS update - goto OMO1 transaction code
In the Updating Info Structures(S001) - double-click the Updating radio button for Info structure S001.
In the Parameters dialog box select Synchronous updating and choose ok.
2) Goto OLI7 Transaction code - run the statistical update.
3) Goto OLIX transaction code - setup version &( will be copied to actual version 000 for reporting
4)Go back to OMO1 do deactive the LIS Update, check radio button to "No Update"
5)Now goto LBW0 and choose option "Deactivate" Delta updating in LIS.
6) In BW, Replicate DataSource, and run info Package with Initilization.
7) Now again in R/3 we need to "Activate" Delta option from transaction code LBW0.
8) and last step is to goto OMO1 to activate LIS Update to Synchronous updating and save.
From now on you can run your Delta Infopackage
Hareesh

Sample Configuration For Ethernet over MPLS.

I am looking for a sample configuration and scenario for the Ethernet over MPLS.I would appreciate if I get some explaination with it.How the LDP is configured for the directed sessions (as per Martini draft) and the auto discovery (as per kompella draft) with respect to Ethernet over MPLS.Cam anyone help me in this ?

Here's a sample EoMPLS configuration on the PE routers:
R1:
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface Ethernet0/0.10
encapsulation dot1Q 10
! 10 = vcid must match the vcid configured on the other side
mpls l2transport route 2.2.2.2 10
R2:
interface Loopback0
ip address 2.2.2.2 255.255.255.255
interface Ethernet0/0.10
encapsulation dot1Q 10
mpls l2transport route 1.1.1.1 10
The LDP directed session will be setup automatically by the router when the xconnect statement is configured.
Cisco IOS doesn't support the Kompella Draft.
For more information, see the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/atomt/ftatomtb.htm
Hope this helps,

Port Range Forwarding Problem for E3000 and Iomega HMNHD Cloud

I'm trying to set up an Iomega Home Media Network Cloud NAS and I'm having problems with opening ports 50500-50599. I have opened port 80 and 443 successfully and included the above port range above as well, but when I check it on www.yougetsignal.com the ports 50500-50599 are still closed. I even tried to split the range in two parts, and still no success. I have been in contact with my ISP and confirmed they do not block any ports in the 50500-50599 range and that the cable modem (a Motorola SBV5120) is operating in Bridge Mode.
I am operating under an older firmware and hope that is not the cause of this problem. Also, using Win7 and Vista (tried and failed on 2 laptops).
Did I forget anything? Any suggestions/solutions? Thanks.

You may want to check out the list of tested hard drives to work with this router first. The link is E3000 and E2100L hard disk compatibility list. Based on the list, your iomega home media is not included. On the link for the tested hard drives to work with E3000, it is indicated that if your hard drive is not on the list, it may or may not work. With your case, since it is not working it may be due to compatibility issue.

VLAN Configuration for Internal and Guest Wireless

Hello,
We are using the following hardware…
SG300-52MP switch -- latest firmware
ASA 5512-X firewall -- 9.1
Aironet AP1131AG WAP
We have the following networks…
10.252.4.0/24 = Internal = ASA-01 interface = VLAN1
10.252.6.0/24 = Guest = ASA-02 interface = VLAN6
10.252.6.0/24 = VOIP = ASA-03 interface = VLAN3
The Aironet supports two SSIDs, Secure (RADIUS) and Guest (WPA2), which are supposed to provide access to the appropriate interface on the ASA.
Relevant parts of the WAP configuration are…
dot11 ssid GUEST
vlan 6
dot11 ssid SECURE
vlan 1
interface Dot11Radio0
no ip address
ssid GUEST
ssid SECURE
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
interface Dot11Radio0.6
encapsulation dot1Q 6
no ip route-cache
bridge-group 255
interface Dot11Radio1
no ip address
no ip route-cache
ssid GUEST
ssid SECURE
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
interface Dot11Radio1.6
encapsulation dot1Q 6
no ip route-cache
bridge-group 255
interface FastEthernet0
no ip address
no ip route-cache
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
interface FastEthernet0.6
encapsulation dot1Q 6
no ip route-cache
bridge-group 255
interface BVI1
ip address 10.252.4.4 255.255.255.0
no ip route-cache
ip default-gateway 10.252.4.1
We can manage the WAP through it’s Internal IP address (10.252.4.4).
And the “Guest” wireless network is working -- connecting to that SSID provides the client with the correct IP addressing (10.242.6.X from VLAN6/ASA-02). [Note: the VOIP DHCP and network access also works correctly.]
The “Secure” wireless network is not working however -- the client never receives an Internal DHCP address from ASA-01, and even if you hard-code the client’s IP, no IP4 traffic ever passes.
[Note: connecting a device to a SG300 port with the “Default” configuration provides the client with an Internal DHCP configuration, and it works as intended.]
While this may be a problem with the WAP configuration, I would like to confirm that it is not an issue with the switch not passing traffic correctly.
I have a feeling that I have configured the VLANs on the ports incorrectly.
Relevant parts of the SG300 configuration are...
v1.3.0.62 / R750_NIK_1_3_647_260
vlan database
vlan 3,6
ip dhcp snooping
ip dhcp relay address 10.252.4.1
ip dhcp relay enable
bonjour interface range vlan 1
interface vlan 1
ip address 10.252.4.2 255.255.255.0
no ip address dhcp
interface vlan 3
name VOIP
interface vlan 6
name Guest
interface gigabitethernet45 -- Access mode, Untagged VLAN6
description ASA-Guest
ip dhcp snooping trust
switchport mode access
switchport access vlan 6
interface gigabitethernet46 -- Access mode, Untagged VLAN3
description ASA-VOIP
ip dhcp snooping trust
switchport mode access
switchport access vlan 3
interface gigabitethernet47 -- Trunk mode, Untagged VLAN1 and Tagged VLAN6
description WAP1
switchport trunk allowed vlan add 6
interface gigabitethernet48 -- Trunk mode
description ASA-Internal
ip dhcp snooping trust
ip dhcp relay enable
Can someone who understands this switch better than I do please confirm the VLAN configuration? THANK YOU!

Welcome to the discussion area!
+PCI regulations do not consider VLAN a secure way of keeping the data isolated. Does anyone have any technical information on how the device creates the guest wireless network ?+
I spoke to Apple Support some time ago and was told that Apple uses VLAN to create the Guest network, and also that formal documentation was not available on this topic. I was referred to the AirPort Extreme Specifications for available information.
This was some time ago, so if you need more up to date info, you might want to try to contact Apple to see if they are willing to share more information about this feature. Although, since VLAN is used, your question may already be answered.
FWIW, to use the Guest Network feature in a home situation, the AirPort Extreme must be set up as the main router controlling DHCP and NAT on the network. If you were thinking of installing the AirPort Extreme behind another router, the Guest Network feature would not be available in this type of configuration.

Supervisor Engine 6-E (WS-X45-Sup6-E) configuration for 10G and 1G connectivity

Hi Community,
I need to confirm something.
With the WS-X45-Sup6-E supervisor engine, is it possible to use one of the uplink ports with the X2 optics for 10G speeds and the other port with a Cisco Twin Gigabit Converter Module so as to have 2 1Gb ports?
Or does it only work with 2 10Gb or 4 1Gb only?
Thanks,
Peter

Sorry but you can't mix and match on the Sup 6. There's a single stub ASIC inside the card which causes this limitation.
The configuration guide explains it here.

DNS Help: Configure for local and extenal services using same domain name?

Hello all. I'm setting up a 10.5 server, have scoured these great forums and gotten close, but am still stuck. Any help would be greatly appreciated.
My network setup is as follows: Internet (2xT1) > modem > router/firewall/NAT device > XServe > switches > rest of network, clients, etc. Pretty standard, I believe.
I'd like to use this XServe on our local network/intranet/LAN only for OD, networked home directories, AFP, iCal, Time Machine, Print and Software Update.
My website is hosted on an external server.
My email is also hosted on a (different) external server.
Domain is school.edu
XServe name is xserve.school.edu
XServe is 10.0.0.25
I've gone through Apple's recommended DNS setup (supplemented by some great info found here on the forums....), and am able to connect to other Internet sites (with client's DNS server set as 10.0.0.25), but unable to connect to www.school.edu, or send/receive mail to/from mail.school.edu.
In short, connecting to external domains that are NOT related to my school are fine, but I'm unable to connect to any domain that IS related to my school.
If anyone out there can shoot me some notes on how to configure the DNS settings, zones, forwarding, etc. to accomplish this, I'd be VERY appreciative.
Thanks, in advance, to anyone who can help me out.
Cheers,
Tim

In short, connecting to external domains that are NOT related to my school are fine, but I'm unable to connect to any domain that IS related to my school.
If your server thinks it's authoritative for 'school.edu' then you have to add records for every host in the school.edu zone.
For example, if you want to be able to resolve 'www.school.edu' then you have to have a 'www' record. If you want to send/receive mail you have to add an MX record, and so on.
It doesn't matter that you're not responsible for those servers, it's just that since this machine thinks it 'owns' school.edu it will only respond with records in its own zone and won't care about what any other name server says, even if that other name server is authoritative for the zone.
FWIW, that's often why people running stub servers like this choose a separate subdomain (like 'dept.school.edu') so they can leave the main school.edu records on the main server and have full control over a subdomain.

How to run a silent configuration for Forms and Reports 11g ?

Hi all,
I've run a silent installation for Oracle Forms and Reports 11g R2 in Windows 7 64 bit.
I made it using a response file called install_only.rsp. Now I want to run the configuration also in silent mode.
How can I do it ?
I know that I can use a template called configure_only.rsp. However, i don't know what is the correct syntax for the command to start configuration.
Should I use the same setup.exe installer and inform configure_only.rsp as response file ?
The command below is the appropriate command for this task:
setup.exe -silent -response configure_only.rsp
Or is there another way to be followed?
Thanks a lot.

Alright, I eventually found the answer.
Configuration must be run from directory on windows.
Command is shown below:
<FORMS_HOME>/bin/config.bat -silent -response <path-to-response-file>

How Do I Create Default System Configurations for On- and Off-Dock?

I recently purchased a T510 laptop with WIndows 7 Professional 64-bit and a Series 3 minidock. I would like two create two default system configurations (namely specifying active montiors, screen resolutions, networking options, and power management). I'd also like the laptop to detect the presence or absence of the dock and automatically switch accordingly. How can I do this? Thank you.

Dear DavidLeon65,
Good afternoon. I am sorry to learn of the difficulties you are experiencing with the bluetooth connection in your car. I know this can be frustrating. It would be my pleasure to address your bluetooth concerns.
When the bluetooth connection drops out, is the phone near you? Also, do you have Wi-Fi turned on? If so, please turn off Wi-Fi, then test. What software version do you have? For directions on how to check the software verison on your phone, click http://vz.to/SrMyDh
Thank You,
MichelleS_VZW
VZW Support
Follow us on Twitter @VZWSUPPORT

Biller Direct configuration for AR and AP

Hello,
I have Biller Direct 6.0 installed and already configured XCM, but I would like to know if its possible to configure the application with Accounts Receivable and Accounts Payable at the same time to show bills from both?
Thanks.

- Define Interest calculation Types
SPRO->Financial Accounting-> Accounts Receivable and Accounts Payable-> Business Transactions-> Interest Calculation-> Interest Calculation Global Settings-> Define Interest Calculation Types
It determines whether interest is on per item or balance
- Interest Indicator
SPRO-> ...->Interest Calculation> Interest Calculation Global Settings> Prepare Interest on Arrears Calculation
- Interest Rates
SPRO->.....>Interest Calculation> Interest Calculation > Define Reference Interest Rates
- Interest Values
SPRO->........>Interest Calculation> Interest Calculation > Enter Interest Values
- Assigning Reference interest rate to interest indicator
SPRO->..........>Interest Calculation> Interest Calculation > Define Time-Based Terms
- Interest Posting
Tcode-OBVI (Approporate GL Accounts should be existing for Interest Accounting and they are configured here)
- Also set the interest indicator in GL Account Master record
- Interest Calculation
Depending on requirement, run the appropriate TCode. eg: F.2B and that will calculate interest on open items of customers
Rgds

FI 6248 Pre Licenced ports(1-12) configuration for Ethernet and FC

Similar Messages

Maybe you are looking for