Fiber optic connections

Hello,
I want to connect 4 x 3560 switches via Fiber on SFP ports, one to other. These switches are about 250 meters apart from each other. What kind of fiber cable, connectors and SFP module should I use?
Thanks

For 250m 50Micron Multiimode Fiber(MMF) (MAx distance550m for this fiber)would be fine,if you dont expect any change in disatnce later.
GLC-SX-MM=
1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength
You can use above card and can check when ordering what kind of connectors above card have.
Check this linkto see other cards available as you know your future palns
http://www.cisco.com/en/US/docs/routers/7200/install_and_upgrade/gbic_sfp_modules_install/5067g.html#wp34124

Similar Messages

  • Can't see others in iChat over Fiber Optic connection

    This was a strange, recent occurence. For the past few years, those of us on Macs (G5's and a PowerBook with latest OS and updates) have been able to communicate via iChat. With new offices, most Mac users went to the new building. I'm still in the old building where the network server is kept. Once the others moved, we are no longer able to see each other via iChat. The only exception are two stations in the same office which share the same Ethenet wall connection.
    Bringing any station back into the old building and connecting to the network will allow this station and my station to see each other, so I've narrowed the situation to our cable connection from the new building to the network server here in the old building. The cable used to bridge the two buildings is a Belkin 3 meter Multimode LC/ST Duplex Fiber Optic Cable.
    I am able to see other Macs on the network through the Finder. I've just lost iChat and VNC capabilities since we've gone to this connection. If anyone has any ideas on how to correct the situation, whether they be adjustments to the Macs' Network settings or ideas of proven alternatives to the connection, all would be appreciated.
    Thanks.
    G5   Mac OS X (10.4.8)  

    Hi DrVvack,
    Welcome to the Apple Discussions
    It is likely that the computers in the new building are in a different subnet of the LAN
    Lets say you are at 192.168.1.100.
    Others in your building also start 192.168.1.xxx
    The other building is likely to be on a router for that building. Now the router is probably at an IP that is in the same group as your computer - but it will be issuing IPs of it's own.
    Now a bit like street numbers this other router could be using a similar set of IP addresses (192.168.1.xxx) but it is the IPs in relation to the original routing device that makes a difference.
    You can get around this by creating a Virtual Private Network then the Bonjour side of iChat will see everyone.
    Another option is to have the second router in Bridge mode or Access point mode (not routing) and have everyone have an IP from the original device.
    10:41 PM Wednesday; February 14, 2007

  • Connecting iPod to stereo with fiber optic cable???

    My kingdom for the right answer to this question.
    I'm brand new to the whole iPod scene. Just bought an 80GB video iPod and I want to use it with my stereo system instead of the old bulky 200 CD carousel.
    I see that I can connect the iPod and stereo using the AV connection kit, but isn't there a way to get digital audio sound quality with some sort of fiber optic connection?
    Will the Monster iCable Fiber Optic Kit work? It doesn't list the iPod as a use, but it sure looks like the non-Fiber optic end would fit into the iPod headphone jack.
    If anyone knows, I'd greatly appreciate the help. I'm a total newb about this and haven't had any luck with my online searches.
    Thanks in advance.

    No you cant do it but
    http://discussions.apple.com/thread.jspa?threadID=863621&tstart=180

  • Switched to fiber optic and now time capsule unable to do backup.  What do I need to do?

    I recently switched to a fiber optic connection.  Time capsule is connected.  Green light is on.  However, it is unable to do a back up.  What do I need to do?

    reset the TC to factory and start over with a clean new setup.. this is always required when you change over network items.
    The computer no longer knows where to find the backup. A factory reset of the TC does nothing to the backups already on the hard disk.. it merely resets the router.
    The Factory Reset universal
    Unplug your TC/AE. Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
    Release reset.
    If it doesn’t flash rapidly you have released reset at some point and try again.
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
    No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    When you redo the setup of the TC, I recommend you stick to short names with no spaces and pure alphanumeric.
    Then reset TM.. see A4 here.
    http://pondini.org/TM/Troubleshooting.html
    Setup TM again aimed at the renamed TC.. it will say it is going to do a new backup but when it starts it will discover the existing backup and continue as before.
    Post back with actual error messages if it fails.
    You can load the widget see A1 in the same reference so you can check the TM log.

  • I recently bought an Airport extreme, while I was living in Japan, and had a fiber optic modem. The Airport connected fine and I had wi-fi I moved back to the US, and when I got my docsis(?) modem from COX, it  wont work with my airport extreme help!

    Basically had APxtreme working with fiber optic in Japan, got to the states with Docsis(cisco) modem and my APxtreme doesnt work now. Tried forever, and it just didnt work, I had a yellow light for internet on airport utility with a green light for the APxtreme? Still nothing workey....

    Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • ATV2 Connected with HDMI for video and fiber optics for Sound but unable to located the fiber optics option in ATV2

    hello everyone, I currently have my ATV2 connected from HDMI to my TV for Audio&Video but I want to run just my HDMI for Video and my Fiber optics cable for my Sound.  I am unable to locate in the settings where I can change my sound to Fiber optics output.
    Thank you
    Steve

    ok so I figured it out.. I just needed to go into my surround sound and select optical out. 

  • I upgraded to Fiber Optic today and now my ipad mini won't connect to the internet although it shows a signal

    As the title says, we changed to fiber optics today (yay! so speedy) and all our devices (Macbooks, iphones) connect just fine.  My ipad mini (about 1 year old) won't connect although it finds the network on the airport effertlessly and shows full signal bars as if it is connected.  For all intents and purposes it looks like it is connected, but it isn't.  I have done all the usual - turned on and off (router and device), forgotten network, renewed network lease, reset network settings, reset all settings, etc. Everthing! Still not working. Help please!!!!!!

    Hello Tom,
    So this is the Airport Forum.  Hence when you were discussing your "Airport", one assumes you are referring to the Airport Extreme or Airport Express  (ie - http://www.apple.com/airport-extreme/ or http://www.apple.com/airport-express/).  It is slightly confusing when Apple refers to the Airport being the wireless in devices as well as their wireless routers.
    It would help us if you told us what type of connection, for instance I live in the UK and have Fibre Optic (to cabinet) and have a cable modem from Virgin Media, which I have then connected (via ethernet) an Apple Airport Extreme (6th Gen) to distribute the internet connection and my local LAN. 
    Maybe you had ADSL prior and are now on Fibre via cable? 

  • Want to reinstall OS X on old mac before sale.  How do I connect it to internet service (ATT 'fiber optics') without a cable?

    Want to sell old iMac.  It has been backed up, de-authorized with iTunes, and wiped with the 35-pass erase.  Now I want to reinstall OS X but no longer have an internet cable as we have gone from TWC to the ATT 'fiber optics' system since the old Mac was erased.  Please help.

    Be sure to follow Apple's instructions in this document:  What to do before selling or giving away your Mac - Apple Support. If you don't you can create a problem for the buyer and yourself down the line.

  • Interdepartment connectivity via fiber optics, which wquipment to use

    I have given a task to interconnect department with one another via fiber optics.
    This means there will be a core switch in a server room which will interconnect these departments. The each departments are away from server room approx 900 meters and 1500 meters. Kindly tell me which fiber optics cable to use ( single mode or multi mode) and which cisco switch to use in the in the core ( server room) and in the departments (one deptt is 900 m and other is 1500 meters away from server room) . kindly also tell me which fiber optics module to use in the switch and which connector.

    Since in both cases you are well within the reach of multimode fiber, it makes no sense to look any further, as it is the most cost effective solution unless you need 10 gigabit performance.
    As to what switches to use, there are a lot of variables once you get past the basic requirement here of having of having two optical ports on the one in the server room, and one optical port for the other two. Other considerations are how many ports do you need in the server room, and in each of the two departments. Then features, performance, and reliability factors come into play, along with budget.
    If you don't need a lot of ports, and you are looking at normal office levels of traffic, 3560's might be a good choice. You could put a second one in the server room, and duel home the servers and department switches to them to add redundancy. That would make a single switch failure unlikely to take out the whole network at one time. One the other hand if you need hundreds of ports, have a mission critical situation, or expect intensive levels of data traffic, then you will need to look at high end switches such at the 4500 and 6500 series.

  • Does anyone know how to access the sound software on a Mid 2010 Mac Pro? I have a Logitech Z906 5.1 surround system with fiber optic in and out, I only seem to be able to get stereo and simulated 5.1 sound .

    A mid 2010 Mac Pro, trying to get 5.1 surround out of the onboard sound software using fiber optic out connected to a Logitech Z906 5.1 speaker sys. with fiber optic in and out, all I get is stereo and simulated 5.1 sound out of the speakers. In utilities, Audio Midi Setup I can't get the Mac to see the Logitech speakers for 5.1 speaker configuration. Without being made to feel like a dummy, does anyone have a solution? Thanks, Carl

    Hello John, I figured it was a signal issue. All the speakers fire and the sound is great. I was running the speakers thru a Dell PC with a Creative X-Fi Elite Pro, THX Certified, 7.1 soundcard using a fiber optic from the Mac Pro to the Z906's, it worked great until the Dell died!!! When I bought the soundcard from Creative I also bought the GigaWorks S750, THX Certified, 700 watt, 7.1 speaker system, used the speakers for 11 years and then the woofer/amp said "I QUIT" Creative quit making the speaker system and the sound card. The satellite speakers from the Creative GigaWorks speaker system still sound great (rated at 78 watt each) and are a little better speaker than the one's that came with the Z906 and the wattage from the 906 is sufficient to drive the satellites without any distortion. Thank you for addressing my issue, you confirmed what I suspected all along, just needed to hear it from someone with the same setup.
    One last question, I purchased a Diamond Multimedia USB Soundcard, can't use the fiber optic(not supported by Mac) but the green, tan and black RCA's plug in and produces adequetly. When you plug your 906's into the Mac Pro using the fiber optic how do you set your speaker configuration? When I plug into the mac pro with fiber optic the 'Audio Midi Setup' does not seem to see the 5.1 configuration. Any thoughts there?
    Carl

  • Which is better for AUDIO: HDMI or the Digital Optical Fiber Optic Toslink Audio Cable?

    Is there a difference in Audio performance between your standard HDMI hook up (for my Blue Ray Player) or adding the Digital Optical Fiber Optic Toslink Audio Cable. Which will sound better????
    Please help... 
    Thank you for your time!!!

    Well that is huge debate here. My opinion is HDMI cables are WAY over priced for what they are. Do not be lead to believe you have to have a 100 dollar hdmi cable, I think 50 is crazy high myself. My only concern is getting one so cheap that it might have poor connections or not last. Also if you run it in a wall it has to be rated for that.
    I have a Rocketfish cable and it works fine. My guess would be the dynex cables are fine too. And if your not buying it from Best Buy there are other options as well.
    Something else to keep in mind as well. If you only have one HDMI device and you hook it up to your reciever using HDMI you will need two cables for one device. The one that runs to the Reciever and then the one from the reciever to the tv. If you use an Optical cable you only need the one HDMI cable. Run the HDMI cable from the blu ray to the tv, and the optical line from the player to the reciever. This will give you 5.1 dolby or dts through the reciever and also sound through the tv since HDMI carries sound as well as video.
    But if money (for cables) was not an issue the HDMI cable supposedly can offer the best sound quality of the two.

  • Infinity 2 package (so fiber optic) on a Home Hub ...

    Hi people I'm a little stumped with whats occurring with my Home Hub 5. I'm moved into my current flat in January and had the Infinity 2 package installed at that point.
    Now I will add that the speed hasn't been terrible, which is why I never really noticed before until I saw another HOME HUB 5 setup today at my cousins and his is wired differently to mine with a completely different modem and router to mine (well I only have the Home hub 5 doing both jobs for me but he has two separate devices given to him one of which was from B.T) thought we pay the same and we live very close to each other. So whats confusing me is that my HH5 has a DSL cable going into the back of the Home HUB 5 as an input from my one and only phone socket in my flat and he has a white modem feeding his Home Hub 5 with a RED WAN cable as an iput.
    So I have just the one cable and mine is a DSL connection (not RED WAN), and his has the RED WAN lead, which is clearly fiber optic feed from a separate modem.
    So does this mean I only get DSL+2 max and not fiber optic speeds??? because clearly I dont have fiber optic running into the back of my home hub. I'm paying for A BT infinity 2 package which I'm guessing should be a Fiber optic set up but yet I have DSL cable or can they make me pay the same and give me older technology???
    As mentioned I was at my cousins earlier today and he pays the same as me money wise, he is four streets away but yet has the RED WAN input (which is clearly fiber optic) and Im paying the same but yet only have a DSL input.
    Now I have looked online and it would appear that they may only have to wire fiber optic to the house (curb) and the internal wiring from the master bell socket to the whole building is down to my land lord but my question is thought should I be paying for a fiber optic package when I'm clearly on a DSL connection package inside the property??? should this of not been mentioned to me when it was set up, like "sorry mate I'm fitting DSL and not fiber optic here, enjoy"
    My other question is after this discovery today wanted to get rid of the Home Hub 5 for a third party modem/router which I already had. I have a Belkin DSL+2 from my last address but always thought I couldn't use it here because I was unaware that I was running DSL, so today I plus it in and set it up correctly and now the Belkin cant/wont connect.
    I have ran speed check tests on the Home Hub 5 and I'm getting about a ping of 29 and above 70 mbps down and above 18 mbps up, but that's only to one site and that's only minimal packets of data (I have no idea how reliable these tests are) (speedtest.net)
    Just with the new Belkin flitted (its a modem and router) it cant connect as the DSL connection bums out all the time every time I try to connect.
    I'm guessing this is because for a DSL connection in the flat its quite good and the Belkin cant handle it???
    but if you try and find a modem/router which is fiber optic via a DSL connection, there is no such thing, how is my home hub 5 running such high ish speeds via a DSL connection??? and can I get a better modem/router than the free Home Hub 5 which will run off a DSL connection but at fiber optic speeds???
    Should I be getting these speeds??? are the speed tests talking rubbish???
    Can I get a better modem router than the home hub???
    Please help the Home Hub 5 is really not helping my gaming :-(
    Many Thanks
    Rich.
    Cornwall
    UK

    You have a Homehub 5 which has a built in VDSL modem. Your speeds indicate you are on Infinity 2. You would not be able to get those speeds on ADSL. To check you can  use this speed tester then carry out the further diagnostics and post back a screen shot of all the results including your IP profile for up and down. This test must be done with a wired connection.
    http://speedtest.btwholesale.com/
    Because you have a Homehub 5 can you also post the stats from 1-12 by logging onto the homehub management pages then troubleshooting > helpdesk. http://bthomehub.home/ This will show your connection  type and speed.
    Your cousin will more than likely have an Openreach modem and a Homehub 4. The Homehub 4 does not have a VDSL modem built in hence the reason it must be connected via the Openreach modem.

  • Can I Replace or Extend the Fiber Optic Cable?

    There is a cable that runs from the Verizon box outside of my house, comes into the basement corner  of the house, and plugs into the router.  Do I assume this is fiber optic cable?  This cable is about 3 ft long which is problematic in getting a good signal throughout my house.  I would like to move the router up one floor.  All the other cords and cables are long enough to do so.
    My question is what is this cable called and can I replace it or extend it myself?  If so, is there any pertinent information I would need to know to do so such as part names and where to get them.  If not, how do I get a longer cable installed.
    I am not tech savvy and grateful for any help. 
    Solved!
    Go to Solution.

    rebeccajeanne wrote:
    Do I assume this is fiber optic cable?  
    No.  The fiber optic cable attaches to the Optical Network Terminal (ONT), which is usually outside.
    For speed tiers < 100Mbps, the installation is usually coax from the ONT to your router.
    For speed tiers > 100Mbps, the installation is always ethernet from the ONT to your router.
    If the cable from the ONT is indeed an ethernet cable, you can certainly replace it.
    The ONT has a standard RJ45 jack which the other end of the cable is connected to.
    You can confirm if you're connected  via ethernet in two ways.
    1)  The WAN ETHERNET light on your router should be lit and the WAN coax light should be off.
    2)  The ethernet cable should be connected to the white WAN port on the back of your router.
    Since your ONT is outside, replacing the ethernet cable presents a couple of problems..
    1)  When VZ installed the cable, they passed it through the wall, then sealed the opening with silicone.
    You need to make sure you can fit a preterminated cable through that opening unless you're capable of terminating a cat5 cable yourself. 
    2)  You need to reseal the opening with silicone.
    An easier option is an RJ45 coupler.
    http://www.amazon.com/Britta-Products-RJ45-Coupler-F-F/dp/B000BSLW8U
    rebeccajeanne wrote:
    Can Verizon replace it for a longer cable?  
    Yes, but they will charge you a truck roll to do so.  $88 or so.

  • Fiber Optic Power lvl

    I own a 20" Imac (2006) for 3 years I have been using the fiber optic output to my receiver via a 3 port fiber optic switch shared with a windows cpu and my tv. It took me about 6 different types of switches that to find one that did not reduce the signal to the point it was inoperable.
    About 6 months ago it just decided to stop working I assumed the cable had been damaged due to a 1 year old yanking on it. So I put off investigation until I got around to obtaining a new cable 10' (old was 10'as well) when I replaced the cable, however, it still would not work.
    I figured my switch had gone bad or something so I then checked the other devices just to be sure they still worked. I even switched to the port the Imac was using with no problems (using the new and old cables that were for the Imac). I can bypass the fiber switch and plugged the Imac directly into the receiver with no problems. While not detrimental I used to enjoy not having to expose my fiber ends to potential danger of contamination or damage. Not to mention not having to reach behind my receiver when I want to switch devices.
    I do realize my problem ma be a bit unique but has anyone heard or know if a update has recently lowered the power output of the Imac's TOSLink output port? Or if anyone knows of a better fiber switch with 3 ports that may have less loss I have tried 6 ranging from $9.99 to $78 the one I am using is
    http://www.amazon.com/gp/product/B0014Z29RW/ref=pdlpo_k2_dp_sr_3?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B0 00812QC6&pf_rd_m=ATVPDKIKX0DER&pf_rdr=11S9KZYH7K9B3BJ8QPHB
    Any help or input would be greatly appreciated

    I haven't heard of anything about an alternate power source for Digital Voice. I don't see how that is possible considering Digital Voice essentially works just like FiOS POTS does. The ONT still needs to be powered by the Battery Backup or AC Power, and that's all that would be to it.
    Now that you have FiOS, it's going to be difficult to get the Copper service reconnected. Verizon will not normally reconnect the copper unless there's something extreme or there is a medical need that requires the assurance of a copper line. You can ask around to see if you can get it connected or not, but failing that, I would invest in a small generator (tiny camping one, power draw is basically idle run lol) to keep the ONT powered up as needed for the phone service, if it is at all possible to do. The Fiber Optic cabling will remain lit since the Central Office should remain powered off of Diesel Generators/Turbines/Batteries for quite a while.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

  • How to build a redundant fiber optic ring

    Hello everyone. I would like to connect 10 buildings with a redundant fiber optic ring and have a control room connect to te closet building in the ring to  receive data from our process control systems which are in the buildings in the ring. They are DCS systems that feed information to the bacbone over FTE. Can someone point me to a document that shows what I need to do and a sample architecture. Can I use Catalyst 2960S switches or do I need 3750s in all my buildings. Thanks in advance for any help.            

    You will need some form of separation from your process control domain from the business network. If you have enough fibre pairs, then VRFs can be used to bind to the interfaces, or you can bind to the Vlans to the appropriate VRF. The important part is to ensure that the process control network is not routable from the business network.
    With the FTE, check with the vendor that if it's handled within the DCS system and you only need to provide separate Vlans for L2 communication. You will also need to consider some form of authenticated gateway to handle third party external access to support your process control network.
    Don
    Sent from Cisco Technical Support iPad App

Maybe you are looking for