Fieldpoint config and functions
hi,
i connected a fp tc 120 i/o module and fp1000 network module.
successfully configured but where to save the configuration file?
i cannot see any fieldpoint read, write, etc functions in the block diagram of labview version 8.2. from where do i get those functions and where to save them?
Hi kunal227,
You will want to save your configuration file somewhere you can easily find so
if you want to load this specific .iak file again, you can do so.
You should be able to find the FieldPoint VI's in LabVIEW 8.2 under the
Measurement I/O palette. On that palette, you will find the FieldPoint
palette. If you do not have this, it could be that you have the wrong
version of FieldPoint installed on your computer, or you do not have support
for LabVIEW 8.2 installed.
To verify that you have the correct version of FieldPoint installed, open
Measurement and Automation Explorer, expand the Software tab under My System,
and select FieldPoint. The window on the right will display the version
of the driver. For FieldPoint to work, you need to have FieldPoint
version 5.0 or later installed.
If you have verified that you have FieldPoint 5.0 or later installed on your
machine, but still cannot see the FieldPoint VI's in LabVIEW, you will need to
verify that you have installed support for LabVIEW 8.2. To check this, go
to Add or Remove Programs in the Control Panel, select National Instruments
Software, click the Change/Remove button, this will bring up a National
Instruments Software window, select NI FieldPoint, and click the Modify
button. Now, you will see what FieldPoint features you have
installed. Make sure that the box next to LabVIEW 8.2 has an image of a
hard drive and not an X. If the box next to LabVIEW 8.2 has an X, click
on the box and select Install this Feature.
Please let me know if you have any further questions by replying to this post.
Message Edited by cphuong on 05-31-2007 09:49 AM
Regards,
Ching P.
DAQ and Academic Hardware R&D
National Instruments
Attachments:
FieldPoint Version.JPG 52 KB
FP_LV_Support.JPG 64 KB
Similar Messages
-
Where config partner function in stage of a route?
Hi all,
Please help me find where config partner function in stage of a route. When I run tr. vt03n, go to Stages, press on Departure point, go to "Details on Stage" and go to Partner. Here I see Partn.Funct. Where config in SPRO еhese partner function?
Thanks.Hi
Customize the partner profile in spro.
S PRO > I MG_> LE -->Transportation --> Basic transportation functions > partner control>set up partner determination for shipments.
Here in partner determination procedure assignment we need to assign the partner function to the shipment type.
Hope this answers your query. -
Distributing a deployment.config and deployment.properties for proxy settings.
I am trying to define the minimum config required to populate a deployment.properties with just proxy settings and point to this with a deployment.config.
I am finding that that recent versions of 1.7 and 1.8 do not adhere to the browsers settings properly and not all traffic is following the proxy rules in use by the browser. However, if I manually override all traffic to a proxy the applets running on internet based sites function (no intranet sites use java here). If I use a deployment.config, I can see the resulting proxy settings are enabled in the control panel app and the appear exactly the same as per user manual settings, however they are not correctly used.have any ideas?
Any one have any ideas?.
ThanksHi Kevin,
I am actually working on the same problem.
I need to deploy Java 1.4.2_07 on clients with a mandatory setup. I tryied the deployment.config and deployment.properties file but didn't get it working yet.
I guess we should share knowledge to find a working solution.
It would be nice, if you could email me at:
[email protected]
regards,
Volker -
Credit Card config and encryption
Hi frnds
I would appreciate if anyone can provide the config steps for credit card and also the step for encrytion. If you have a doc on it then please mail it to [email protected]hi
CREDIT CARDS
Go thr below links:
PAYMENT CARDS:
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/SDBILIVPC/SDBILIVPC.pdf
http://help.sap.com/saphelp_erp2005vp/helpdata/en/93/745309546011d1a7020000e829fd11/frameset.htm
Overview
This document attempts to explain in the brief the credit card processing in SAP.
SAP provides a flexible and secure payment card interface that works with the
software of selected partners that provide merchant processes and clearing house
services. In SAP the credit card processing is integrated with the sales and
distribution module.
Payment card configuration
Much of what is required for credit card processing to work with VISA, Master
Card, and American Express is already set up in SAP.
For all credit card configurations refer to
Define Card Types
Transaction SPRO IMG ‡ Sales and Distribution ‡ Billing ‡ Payment Cards
Here we define the type of cards that can be used in the system. A four-letter
code is given for each card type. E.g. MAST for Master Card, VSAJ for Visa
Japan. A function module for checking the card number is also specified here.
1. Define Card Types
Credit Card Configuration And Processing In SAP
Maintain Card Categories
(a) Define card Categories: Here we specify the card category of the
payment card. With this the system automatically determines the card
category when you enter a card number in master data or sales
documents.
(b) Determine card categories: Here we specify the acceptable number
ranges for different card types. Also card categories are assigned to the
card types. Even though SAP comes with card checking algorithms
(Function Modules) for standard card types this configuration setting
is particularly useful to those cards that do not contain any standard
checking algorithm already set up in SAP.
2. Determine Card Categories
Maintain Payment Card Plan Type
In this step, you assign the payment plan type for payment cards, the payment
card plan type, to all sales document types in which you will be using payment
cards. You cannot process payment cards if you have not made this assignment
The standard system contains payment plan type 03 for processing payment
cards. 3. Show the screen where this assignment is done.
Credit Card Configuration And Processing In SAP
3. Maintain Payment Plan Type
Maintain Blocking Reasons
In this step, you define blocking reasons for payment cards. You enter these in
the payer master record to block cards. The standard system contains blocking
reason 01 for lost cards.
Risk Management for Payment Cards
Transaction SPRO IMG ‡ Sales and Distribution ‡ Billing ‡ Payment Cards
‡ Authorization and settlement ‡ Risk Management for payment cards.
Risk Management plays a central role within Sales, providing you with checks
and functions to minimize your credit risk. In addition to letters of credit and
export credit insurance, payment cards are among the payment guarantee forms
that you can use to insure payment for sales order items. SAP comes with predefined
payment forms of guarantee as shown below. Customer can also
maintain other forms of payment suited for their line of business.
Credit Card Configuration And Processing In SAP
Define forms of payment guarantee
3. Define forms of payment guarantee
Maintain payment guarantee procedures
In this step, you define Payment guarantee procedure. These procedure controls,
which form of payment guarantee, are valid for a particular customer, and for a
particular sales document type.
The various settings done under this configuration are
Define payment guarantee procedures
Maintain customer determination procedure
Maintain document determination procedure
Assign sales document types
Determine payment guarantee procedures
Maintain authorization requirements*
Here requirements* are set to tell the system how and when to carry out
authorization when a sales order is saved. SAP comes with two requirements
Form routine 1. Carry out authorization only when the sales document is
complete. The system carries authorization when the order is saved.
Form routine 2. Carry out authorization only when the sales document is
complete, but the authorization for all the complete documents is carried out in
batch.
Additional requirements* can be assigned here as per the business requirements.
*Requirements are ABAP/4 code. Requirements for various functions can be accessed using transaction VOFM
Credit Card Configuration And Processing In SAP
4. Maintain Card Authorization Requirements
Maintain Checking Groups
How and when authorizations are carried out depends on the setting you make in
the customizing for maintain checking group routines.
The three main settings that influence authorization are:
a) Authorization requirements
b) Authorization horizon
c) Preauthorization
There are two settings under this setting.
Define checking group: Here a checking group is defined and the
authorization requirement (described in the previous section), Authorization
horizon (described below) and preauthorization settings are done for this
checking group.
5. Define Checking Group
Credit Card Configuration And Processing In SAP
Here you can see a checking group C1 is defined with the authorization
requirement 902. Checking the pre-authorization tells the system to carryout preauthorization
if the order fulfillment date falls outside the horizon. The
authorization horizon specifies the number of days before the material
availability date, or billing date, that the system is to initiate authorization. If a
sales order is saved within the authorization horizon, the system carries out
authorization immediately. If a sales order is saved before the authorization
horizon comes into effect, the system does not authorize at all, or carries out
preauthorization.
6. Preauthorization Concept
In this example, the system has been set to authorize one day before delivery
creation. The system does not carry out authorization when the order is saved on
Day 0, rather on Day 2. Note that the authorization validity period has been set to
14 days in Customizing IMG‡ Authorization and settlement‡ Specify
authorization validity periods. The transaction will have to be reauthorized if
delivery activities take longer than 14 days.
Assign checking groups: Here the checking groups defined earlier are
assigned to different sales document types as shown 8.
Specify authorization validity periods
Here number of days that an authorization can remain valid for different card
types are maintained. Refer to 9.
Credit Card Configuration And Processing In SAP
8. Assign checking groups
9. Assign validity period for authorization for different card types
Credit Card Configuration And Processing In SAP
Account Determination
Transaction SPRO IMG ‡ Sales and Distribution ‡ Billing ‡ Payment Cards‡
Authorization and settlement ‡ Maintain Clearing House
In the following steps, you set the condition technique for determining
clearinghouse reconciliation accounts for authorization and settlement. The
system uses the entries here to determine the clearing account for the payment
card charges. When settlement is run, the postings in the receivable account for
the payment card will be credited and a consolidated debit will be created and
posted to the clearinghouse account. These accounts are a special type of general
ledger account that is posted from Sales and Distribution.
Here, you maintain:
• Maintain field catalog.
• Condition tables and the fields that they contain
• Access sequences and condition types
• Account determination procedures
• You then assign these accounts to condition types.
Add to field catalog
Here you maintain the fields that can be used in the condition table. 10.
Shows the transaction to maintain the field catalog.
10. Maintain Field Catalog.
Maintain condition tables
Here condition tables are maintained with fields that are added to the field
catalog. SAP comes pre-configured with two condition tables 4 and 6. Refer
11.
Credit Card Configuration And Processing In SAP
11. Maintain Condition Table
Maintain access sequences
In this step we define an access sequence and link the access sequence with the
condition tables.
Here an access sequence is defined. SAP comes with the access sequence A001.
12. Define Access Sequence
Once the new access sequence is defined, it is linked to the condition tables as
shown in the next screen.
Credit Card Configuration And Processing In SAP
13. Maintain Access For Access Sequence
Selecting an access and clicking fields will display the fields for the selected
access as shown below for access 10 as shown above.
14. Display Access Fields
Maintain condition types
Here condition types are defined and the access sequence to linked to it.
Condition types are contained in account determination procedures and control
which access sequences the system uses to find condition records.
These are The condition tables.
Credit Card Configuration And Processing In SAP
15. Define condition type
Maintain account determination procedure
In this step an account determination procedure is defined and linked to the
condition type (which in turn is linked to the access sequence).
Define account determination procedure
16. Assign account determination procedure.
Here an account determination procedure CC01 is defined and the condition type
CC01 is assigned to it.
Access sequence linked to the condition type
Credit Card Configuration And Processing In SAP
Assign account determination procedures
In this customizing the previously set up account determination procedure is
assigned to different billing documents.
Assign Accounts (G/L)
G/L accounts are assigned here for the combination of Sales organization, Card
type, chart of accounts and condition types as shown in the 17.
17. Assign G/L accounts
Set authorization / settlement control per account
Each G/L account is assigned an authorization and a settlement function module.
The system will read the configuration a call the authorization and settlement
function module during authorization and settlement respectively.
Credit Card Configuration And Processing In SAP
18. Set Authorization and settlement function module
Maintain merchant IDs per account
A merchant may have one or more IDs for each clearinghouse with which it does
business. Here, you assign these different merchant IDs to their related
receivables accounts.
19. Assign Merchant ID’s
Credit Card Configuration And Processing In SAP
Authorization and Settlement in SAP
20. Sales Order Cycle With Credit Card Authorization
When an order is placed through the front-end system, the order information,
credit card information, billing information, shipping information is passed to
SAP. SAP processes the order calculates the taxes, the shipping costs and reads
the configuration information settings and executes the function module setup as
described in Fig. 18. The function module formats the data and makes a RFC *
call to the payment application**.
The payment application screens the order for fraud, encrypts the data and
communicates with the third party processor who in turns communicates with
the card association and card issuer.
*RFC (Remote Function Call)
*Payment Application: Middle ware between SAP and third party processor/bank.
Credit Card Configuration And Processing In SAP
The third party processor responds back with the response whether the
transaction is approved or declined or referred.
Note: When any item in the order does not have a confirmed quantity, then
authorization is not carried out for the full amount. A small dollar amount
usually ($1) is used as the authorization amount. During the rescheduling run
the system will check for the material availability. If the material can be
delivered within the horizon date, a full authorization for the order is carried
out.
Approved: When the credit card transaction is approved the systems checks for
the material availability, confirms the material for the ordered quantity and saves
the order.
Declined: The material availability check for the material is not made, and the
order is rejected.
Referred: The order is saved and is blocked for delivery. In this situation is
merchant calls the bank checks for the available credit on the card and a manual
authorization is carried out.
21. Sales Order Entry Screen in SAP
Payment Card
Information
Credit Card Configuration And Processing In SAP
The first line in payment card screen is the card check performed by SAP system,
using the card check algorithm function module as described in 1. And the
remaining lines represent the actual authorizations that are carried out.
22. Payment Card Screen
Path Header ‡ Payment Cards.
Settlement
Legally the merchant can charge the credit card after the order has been
completely processed. In SAP this happens after a delivery is created and the
goods has been shipped. In case there is not enough authorization for the order
to be delivered, the system goes out the get the authorization for the remaining
amount.
In SAP settlement is initiated using the transaction FCC1. All the valid
authorization is submitted in a batch to the payment application at scheduled
intervals as specified by the third party processor.
The payment application encrypts this data and communicates with the third
party processor. The third party processor checks if the settlement request has a
valid authorization against it. The third party processor then transfers the fund
from the cardholder’s bank to the merchant bank.
Authorization
Response
Credit Card Configuration And Processing In SAP -
How to find out list of procedures and functions inside a package
How I can find out the list of Procedures and Functions inside a Package.
Look at ALL_PROCEDURES and ALL_ARGUMENTS.
-
Lenovo Yoga 2 13, Kali Linux 1.0.7, Ubuntu 14.04, Windows 8.1 install, config, and wifi fix.
Lenovo Yoga 2 13, Kali Linux 1.0.7, Ubuntu 14.04, Windows 8.1 install, config, and wifi fix.
I wanted to share an experience with everyone I hope will help others avoid what I have gone through the past 3 days. I bought a Yoga 11s that I loved but had some issues with the wireless, Lenovo being awesome replaced it with a Yoga 2 13. I love this laptop but ran into some issues with Linux install/wireless, which I wanted to show how to resolve in one place. Hopefully this will help someone else get through this quicker
I am going to try and write this for someone with little Linux experience, if I miss the mark please let me know and I will clarify the best I can.
For work I need Windows 8.1 and Kali Linux, while for home I prefer Ubuntu.
My Yoga 2 13:
I5 1.6 ghz
8 GB ram
256 GB SSD
ORANGE!
My requirements:
I need Windows
I need Kali Linux (livecd, even with persistent mode was not an option as it would not save the wireless fix or system updates) – I would also like this on a USB drive and not the internal SSD
I would like Ubuntu
Needed to do this:
1. 2 USB thumb drives (at least 8gb in size each) I used 2 Leef Supra 32GB drives. They are my favorite right now and are only about $27 at amazon.
2. Phone that can USB Tether or a USB Ethernet card (External USB wireless will show as "Hardware Locked"). Again you can pick one up for sub $10 if you need the USB Ethernet route. I used my Galaxy S5, you will need to download 200-300 mb of items through this so make sure you have the data if you go that route.
3. You may be able to get a USB wifi card to work if you do the following after boot. This only worked once for me.
a.Type ‘sudo rmmod iwlmvm’
b.Type ‘sudo rmmod iwlwifi’
4. ISOs of Ubuntu and Kali Linux (I used Ubuntu 14.04 and Kali Linux 1.0.7)
5. Software to unzip the ISOs. I recommend 7-ZIP and will be referencing this in this guide.
6. I will include the EFI boot files and the WiFi fix files if I can attach. Otherwise I will provide a link to them.
Link: https://www.dropbox.com/s/puxnnoft3gn2b6l/WiFiFix.zip
Recommended (these are just in case you corrupt something making your system not see any OS
1. I would call Lenovo beforehand and get a set of recover disks (this will take 2-3 days)
2. In the meantime a USB Windows 8.1 or 8 ISO (the repair feature may save you)
*Note: At many points in this guide I detail steps and commands. Please double check that you understand the step before proceeding. There are multiple points where a mistyped command or clicking the wrong option will cause your entire system to fail and you will need to reformat the entire drive and start over. This also will make One Touch recovery not work. Proceed with caution.*
I did not need to disable ‘secure boot’ to do this, but keep in mind that you may need to.
Steps:
First let’s go through the installs, and then we will go through grub config and wireless fix
1. In Windows scroll to computer and right click, select manage.
2. Go to “Disk Management”
3. Select the main HDD (notice Lenovo puts a stupid number of partitions on here)
a. I deleted the D: drive on here, if you do this make sure to copy the drives over to your main C: drive. You will want to run each of the installers and repair the drivers after.
4. I used the space from the D: drive and pulled a little more creating a 50 GB partition for Ubuntu and my swap file
a. You can also add more space by right clicking your C drive and selecting shrink
b. Do not format the partitioned data as this will make identifying it later much easier.
5. Open a command line
a. Swipe from the right of the screen and select search
b. Type ‘cmd’
c. right click and select ‘run as admin’
6. For Ubuntu: Type ‘diskpart’ into the command line
a. type ‘list disk’
i. You should see 2-3 disks depending on if you have one or both usb drives in the laptop at the time. I would suggest only doing 1 at a time so you don’t lose track.
b. type ‘select disk $’ (Replace the $ with the number of the drive)
c. ***** Before proceeding make sure you have the correct drive selected or you can ruin your Windows install and Lenovo one touch recovery will not fix it since we have changed the partitions *****
d. type ‘clean’
e. type ‘create partition primary’
f. type ‘active’
g. type ‘format fs=fat32 quick’
h. type ‘assign’
i. type ‘exit’
6. For Kali Linux: Type ‘diskpart’ into the command line
a. type ‘list disk’
i. You should see 2-3 disks depending on if you have one or both usb drives in the laptop at the time. I would suggest only doing 1 at a time so you don’t lose track.
b. type ‘select disk $’ (Replace the $ with the number of the drive)
c. ***** Before proceeding make sure you have the correct drive selected or you can ruin your Windows install and Lenovo one touch recovery will not fix it since we have changed the partitions *****
d. type ‘clean’
e. type ‘create partition primary size= 3272
f. type ‘active’
g. type ‘format fs=fat32 quick’
h. type ‘assign’
i. type ‘exit’
j. By doing this we can maintain a portion of this drive as the install CD and still have linux install/ liveCD if we need to run it on another machine.
7. At this point the drive is ready to have the contents of the ISO copied over.
8. Right click the ISO and select 7-zip then ‘zip to /’ This should unzip the ISO to the location of the ISO into a folder named exactly the same as the ISO.
9. Once this is done for Ubuntu ISO it is done
10. Kali requires a little bit more to be ready
a. Kali will need some files added for EFI boot. --$--
i. Thanks to: https://forums.kali.org/showthread.php?271-How-to-EFI-install-Kali-Linux
ii. EFI files are located within the wifi fix folder https://www.dropbox.com/s/puxnnoft3gn2b6l/WiFiFix.zip
11. Now let’s start with Ubuntu
Ubuntu install
1. Place USB drive into the laptop and press the “Lenovo boot” button next to the power button
2. Select ‘Boot Menu’
3. Select ‘EFI USB Device (Name of drive)’ Mine stated Leef Supra
4. Select ‘install Ubuntu’
5. Go through the Ubuntu install until you get to select the install drive
6. Once you get to the install portion it will ask you to select from one of 4 options. Select ‘Manually select partition’
7. Select the “Free Space” where we opened up some of the drive
8. You will need to create 2 partitions, I usually create the swap partition at the end of the drive
a. First I create the swap
i. Set at the end of the drive
ii. Set size to 1024 mb
iii. Set type to ‘swap’
b. Second create the ext 4 partition
i. Set to beginning of drive
ii. Set to remainder of the space
iii. Set type to ext4
iv. Set mount point to /
9. Finish the install and boot into Ubuntu
10. You will notice that your wireless is ‘disabled by hardware’ This is fine for the time being and we will worry about this after the kali install. If we fix it now for some reason after installing kali we get the error again and would just need to fix it again.
Kali Linux install
1. Place USB drive into the laptop and press the “Lenovo boot” button next to the power button
2. Select ‘Boot Menu’
3. Select ‘EFI USB Device (Name of drive)’ Mine stated Leef Supra
4. From the grub menu select ‘install kali linux’ both graphical and text work. I much prefer text install
5. You will get a few errors through the install but that is fine
6. The first we see is about network hardware and ‘load missing firmware from removable media?’ – Select ‘no’
7. Then select no ethernet card
8. It will have you name your machine then it will ask you for the root password
a. If you want to just use root *not recommended* place the password here
b. If you wish to use a non-root account then leave these blank and it will ask you for a name, username, and password of the new machine *Very Recommended* - this will also add this user to the sudoers file
9. It will then ask you to ‘partition disks’
10. Select manual
11. Now here is where it can get a little confusing so read twice click once
12. Select the USB drive from this list
13. Mine shows up under (sdb) – Leef Supra
a. It could be sdc, sdd, sde, etc… depending on how many drives you have plugged in.
14. You should see one primary drive that is 3gb or so that is formatted as FAT32. – DO NOT TOUCH THIS PARTITION!
15. You should see the remainder of this drive as ‘FREE SPACE’ select that
16. Create a partition at the end at size 1024mb and swap
17. Then create another one for the remainder of the drive and set it to ext4 with mountpoint of /
18. Continue through the install after you should see an error warning you that ‘you may not be able to boot’ that is fine, select continue
19. Then select from the menu of all the options ‘continue without bootloader’
20. It should finish up then reboot on its own.First setup/boot/fix grub
1. You should be able to boot up into GRUB2 menu now.
2. You may not see kali linux in this menu (make sure you have your towel and don’t panic!)
3. Boot into Ubuntu
4. Once you log in you should see that you still cannot use wireless due to being locked by hardware
5. This is expected
6. Let’s fix grub then we will come back to fixing wireless
7. Plug in your device to connect to the internet (USB Tethering or USB Ethernet)
8. Once you verify that you now have an internet connection run the following from terminal
a. ‘sudo add-apt-repository ppa:danielrichter2007/grub-customizer’
b. ‘sudo apt-get update’
c. ‘sudo apt-get install grub-customizer’
9. You can also edit the grub.cfg manually if you know what you are doing… I did not
10. Open grub customizer
11. It should auto populate and you should see ‘debian (kali linux)’ somewhere in the list
12. It should be mounted to /dev/sdb2 or /dev/sdc2 depending on how many devices you have
13. At this point go ahead and save
14. Reboot and test that you can get into each OS
15. This is where my inexperience got me. I spent 2 of my days so I am including this error: If when you boot into Kali you get an error somewhere that says ‘/bin/sh: can’t access tty: job control turned off’ look above it for an error that looks similar to ‘ALERT! /dev/sdc2 does not exist. Dropping to a shell!!’
a. That error is due to the mount point being incorrect in grub, reboot and from within grub highlight the kali boot. Press ‘e’ then towards the bottom you should see ‘root=/dev/sdc2’ change this to ‘root=/dev/sdb2’ again the number doesn’t matter just make sure it stays the same.
b. Press F10
c. If this boots fine then you will need to go back and fix the grub.cfg or load into Ubuntu and open grub customizer again, it should fix this
16. Now you have 3 working OS on the machine with one being on a USB! Congrats!
17. You can remove the USB with no worry of screwing up your install, but you will not be able to boot into Kali Linux until you replace it. I would suggest only removing it and replacing it while the machine is powered off, but that’s just me.
Fix Wireless
Now is the time to do what probably ¾ of you came here for. FIX THE DANG WIRELESS. This is a huge problem from Lenovo’s side that I hope they realize how important Linux is and will fix. I won’t hold my breath though.
Log into Ubuntu : This is well documented in the following forum post on page 3 by user Haohe:
http://ubuntuforums.org/showthread.php?t=2215044&page=3
His has you download quite a large file, mine should be much smaller.
https://www.dropbox.com/s/puxnnoft3gn2b6l/WiFiFix.zip
1. Download the attached package with the fix.
2. Connect your USB internet device (tether or ethernet)
3. Place the packages somewhere easy to access, in this example I will place them under ~/Desktop/WiFiFix
4. Type ‘cd ~/Desktop/WiFiFix/’
5. Now we need to prep the tools we need.
6. Type ‘sudo apt-get update’ – we did this before, but you know, just in case
7. Type ‘sudo apt-get install linux-headers-`uname –r`’ Note around uname-r they are the ` symbol not the ‘ this is located just above the tab on the same key as ~.
8. Type ‘make’
9. Type ‘sudo cp /lib/modules/3.13.0-24-generic/kernel/drivers/platform/x86/ideapad-laptop.ko ~/ideapad-laptop.ko.backup’
10. Type ‘sudo cp ~/Desktop/WiFiFix/ideapad-laptop.ko /lib/modules/3.13.0-24-generic/kernel/drivers/platform/x86/’
11. Type ‘sudo modprobe -r ideapad-laptop’
12. Type ‘sudo modprobe ideapad-laptop’
13. Type ‘sudo rfkill unblock all’
14. Type ‘sudo modprobe -r ideapad-laptop’
15. Type ‘sudo mv ~/ideapad-laptop.ko.backup /lib/modules/3.13.0-24-generic/kernel/drivers/platform/x86/ideapad-laptop.ko’
16. Next we need to blacklist the ideapad module
17. Type ‘sudo echo 'blacklist ideapad-laptop' > /etc/modprobe.d/blacklist-ideapad.conf’
a. The first time I tried this it wouldn’t work. So I did the following
b. ‘sudo touch /etc/modprobe.d/blacklist-ideapad.conf’
c. ‘sudo vim /etc/modprobe.d/blacklist-ideapad.conf’
d. Enter blacklist ideapad-laptop
e. Exit and save
18. Reboot your Yoga 2 13
19. Boot into kali and see if you have wireless, if you do then you are done. If not we will need to repeat this process with one small little change.
Kali Wifi Fix
1. Copy the sources.list from the package provided
2. Replace /etc/apt/sources.list with the included
3. Some of the file path changes but the process remains the same from here.
Congratulations you now have 3 OSes one portable to other machines and working wifi!
Thank you
SirGed -
Unit testing, integration and functional testing
Hello all,
I would like to know the difference between Unit testing, integration and functional testing. And also what are the testing tools that are more commonly used?
Thanks,
MaxxHi,
Unit testing :
A complete cycle of each module will be tested
ie for PP Right from requirements to planned orders /production orders
confirmation .
Integration testing:
Here cross module testing will be carried out.
ie PP and MM integration
After confirming production order a GR is made /billing is carried out
and delivered.
Functional testing:
This testing is carried out to see whether the system can with stand l the loads during processing by users.
Stress test and volume test.
Regards,
nandha -
Firefox 5 worked fine. I installed Firefox 7, and when I ran it, tabs would just say "connecting to..." and hang. Restarting did not help. Websites open fine in IE and Chrome. Disabled all firewalls and antivirus, did not help. Uninstalled and reinstalled Firefox 5, everything worked fine again. This was using Vista 64-bit.
Upgraded to Windows 7, uninstalled Firefox 5, installed Firefox 7, had same problem. Uninstalled Firefox 7 completely (including the profile information, I saved that information in another folder), restarted computer, and installed Firefox 7 using a completely clean profile. Did not install any add-ons, checked to make sure all plug-ins were up-to-date, and updated plugins.
Now when I start Firefox, I can load 3 or 4 or 5 tabs fine -- after those first few tabs are open, I cannot open or refresh any other tabs -- including about:config and the add-on manager -- I have to restart Firefox. The hangup doesn't appear to be related to what websites I am attempting to open, but it looks like the number is the problem. I have run through all of the FAQ procedures, including changing the max number of network connections to 48, and the problem does not seem to go away.
As a side note, I had this same problem when I tried to go from version 5 to version 6 as well. Version 5 is the most recent version that worked on my system.Can you try Aurora - download it from http://www.mozilla.org/en-US/firefox/channel/
And let us know how it works. -
Diff b/w BAPI and Function Module.
What is the difference between BAPI and Function Module....
By Interface programming do we mean posting data thru BAPI,BDC....Hi Alex,
BAPI: Standard Interface in the R/3 system that allows the system to communicate with components of other business suites.
FM: These are the procedures that are defined in the Function Groups and can be called from any ABAP Program. FM allow you to encapsulate and reuse global functions int he R/3 system.
The main basic difference between BAPI and FM are
1) All BAPIs are FM but not all FMs are BAPIs
2) BAPIs are remote enabled
3) BAPIs interface will not have a changing and exceptions. They can not be used to have use dialog.
Interface programs can post data to SAP either through a BDC, BAPI, IDOC etc. It depends on the type of requirement.
Hope this solves your question.
Enjoy SAP
Rajasekhar -
Use of Procedure and Functions in ADF BC
Hi,
In ADF 11g
1. can I use oracle function and procedures ( having in and OUT parameters) to expose as service interface
2. if yes , How can this be done. and what are the allowed data types as input to procedure/function and can be returned by procedure/function
3. How the transaction control will be achieved using ADF BC service interface.
E.g. one ADF BC creates orders in order details and second creates Order lines in Order lines table. Now if order is created successfully but line creation fails then I want order to be rolled back also.
Thanks.google it out.
How to get two out param which is used in Procedure
http://sameh-nassar.blogspot.in/2010/01/create-plsql-function-and-call-it-from.html
http://adf-tools.blogspot.in/2010/09/adf-function-call-from-el-statement-in.html
http://adf-tools.blogspot.in/2010/03/adf-plsql-procedure-or-function-call.html
http://adfhowto.blogspot.in/2010/11/call-db-procedure-or-function-from-adf.html
Re: use of Procedure and Functions in ADF BC -
Qosmio X300 - Remote control and function bar for windows seven
Hi,
I have bought this PC with Vista x64. I have upgraded it to windows 7 (x64)
But I didn??t find driver for remote control and function bar. The drivers for Vista *64 don't work.
Help me plz.
Thanks for reading
(Sry for my bad English)Hi
The Win 7 drivers are not available for this unit at this time.
But I found some Win 7 drivers on the Toshiba US driver page.
Of course you will not find exactly the same X300 series but you can choose the drives released for Qosmio X305-xxxx
There is no big difference between X300 and X305 so the Win 7 drivers should work too -
The message function on my Ipad just quit working. I was using it while in Mexico and it just quit. I have come home and synced my Ipad with Itunes and function still does not work. How do I get this function to work again?
When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive. It would be a few months old so it wouldn't have the complete library on it....any ideas? I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.
-
Creation and Change Date for Tcode and Function Groups
Hello All,
I need to display the Creation and Change Dates for Custom Tcodes and Function Groups in a Report. Can anyone please let me know the logic of retrieving it.
regards,
MaheshHi,
TADIR and TRDIR is the tables where you can find all these data
Regards
Sudheer -
Are the Pl/sql procedure and function atomic by themself
i want to ask a question does oracle pl/sql procedure and function support Atomicity for the database by themself , or they became atomic incase we call them using begin -- end;
You appear to be discussing transaction scope which is completely independent of PL/SQL blocks like procedures or how you call procedures. It's all in where commits (or rollbacks) are issued.
If you have a procedure like this
CREATE PROCEDURE p1
AS
BEGIN
INSERT INTO some_table( key, value ) VALUES( 1, 'Foo' );
INSERT INTO some_table( key, value ) VALUES( 1, 'Bar' );
END;where the first statement succeeds and the second statement fails as a result of a duplicate key, there will still be a Foo row in the table but the procedure will have thrown an exception. The caller of the procedure may choose to commit or rollback the change-- that will determine whether the first statement's results are made permanent. If you have a procedure like this,
CREATE PROCEDURE p1
AS
BEGIN
INSERT INTO some_table( key, value ) VALUES( 1, 'Foo' );
commit;
INSERT INTO some_table( key, value ) VALUES( 1, 'Bar' );
END;the commit will make the first insert permanent regardless of whether the second statement fails no matter what the calling code does (that's one reason that putting commits in stored procedures is generally a bad idea-- the caller is in a much better position to know what other uncommitted work has been done and whether it is safe to commit.
Justin -
Please compare
methods in C # to connect to SQL Server
database (for example,
3-tier architecture of traditional and
entity Framework(linq to entity or linq to sql object model)
and Linq to SQL) in terms of speed, quality and functionality
to give me tips.
Thank you.
Mojtaba Malakouti.That means we need to compare and post the results here?
Best Regards,Uri Dimant SQL Server MVP,
http://sqlblog.com/blogs/uri_dimant/
MS SQL optimization: MS SQL Development and Optimization
MS SQL Consulting:
Large scale of database and data cleansing
Remote DBA Services:
Improves MS SQL Database Performance
SQL Server Integration Services:
Business Intelligence
Maybe you are looking for
-
RV215W - Problem setting up site-to-site VPN
Hello, I've taken a plane to newbie-land and need help in setting up a site-to-site VPN. I know this is very basic stuff so I apologize for asking something that's been answered a million times before. I just can't find an answer I can translate dire
-
Sound input issues. Not related to Soundflower or Balance issues
So. With the sound flower issues fixed. And my balance knobs in place for my stereo speakers. I have opened up a new song I have been writing. Again the AVIGrandpiano app was the track I was recording on. Like my previous post from last week the
-
CANT USE BLUETOOTH HEADSET AS AUDIO DEVICE
I just got a bluetooth headset today, paired it with my imac, went into teh sound settings, then selected it as my audio input and output device. was working fine all day then all of a sudden it stopped working and no matter what i do it will not sho
-
i want delete all files and leave my mac book pro like the first time. i have system 10.7.5 , i have lot of files and need memory.. what must to do ?
-
HT204081 Which computer apps will allow me to read my downloaded ibooks?
I have purchased a book I need for chool on Ibooks in my itunes and I cannot open it on my imac. I understand that itunes cannot play these files but as well my iphone wont download it because of extremely low internet connection so which app can I g