Fieldpoint FP-RLY-422 does not change status

I am using Measurement Automation to run field point 4.1. I have 2 FP-RLY-422 in the field bank in one of the 422 at address 7 channel 1 the value on the screen shows as 1 if I write a 0 the relays goes on and stays that way until I do a reset. I can not change the value???

Toro,
Are you exceeding the maximum switching capacity of the module? Page 573 of the 2004 NI Product Catalog gives the maximum and minimum specifications. If you remove whatever you have connected can you switch the relay in Measurement & Automation Explorer (MAX)? Did you try swapping the other FP-RLY-422 with this one and see if it behaves the same? Did you try swapping the terminal base (TB-1) and see if the problem follows the base? Otherwise it sounds like it may be an RMA. You can do an RMA by calling 1-877-493-2406.
Ames
Applications Engineering
National Instruments

Similar Messages

STMS problem ( import status - import runnig does not change)

I have the same problem like this:
While Transporting request in our production server the status of request from import running (truck sign) does not change.
But the effect of the request is seen in the production but status does not change.
see :Re: STMS problem ( import status - import runnig does not change)
I did se14 as experts suggested, the history truck sign go away,seem work fine,
but when new request need STMS to trans, the truck sign happened again,
I need you help,thank you!

thanks for all reply,
the last two answers are the same,I think this is the right key,
I'm a ABAPer actually,yesterday I asked our headquarters basis to help,
and I don't know what he did,now this problem is be solved,
PS:I use AL11 to find .LOB now,but not find(maybe it's deleted by our basis),
thanks again!

Import status- import running does not change during the mass import of TR

Dear All,
I have successfully imported single requests in my newly installed SAP ECC EHP4 PRD system but when I have tried to import 8 transport requests(Mass Import) then the Import status is not changing from import running (Truck button still appears).
But the effect of the request is seen in the production system but the status does not change.
I have checked the logs and found that all the requests have been imported successfully but the Truck status does not change.
I have restated the system but no use still the same.
Thanks in Advance...
Latha

Import Running for a long time on ECC 6.0
The background job RDDIMPDP is running on client 000 as well as the relevant client.
Below is the TP System Log:
WARNING: System CC6. Warning. 20090914042136 :
WARNING: Background job not running properly. Function: G Jobcount: 04512801 Status: S.
Please check the system. Use transactions SM21, SM37, SM50.
WARNING: (This warning is harmless if no further warnings follow.)
As per NOTE: 26966, it could be b'cause the background job process slots are occupied,
Regards
Vikas Nagar

Error Message : Object does not exist (status management)

Hi Gurus,
I am working on tcode IW52(Change Notifications). and using badi's for validations at different points.
1. Order level,
2. Notification,
3. Task level validations.
In the task level validations, I have an requirement that if certain condition is met, than user should not be able to delete the task. I have no problem doing that, I am able to restrict it.
Now the issue is :
Say you have 6 tasks, and condition is met for the 5th task and I try to delete it. then the error message "can not delete task" is getting triggered from the badi.
and after this error message if you try to do any functionality on the 6th task, I am experiencing error message "Object does not exist (status management)".
Is anyone aware of this error message, any suggestions are highly appreciated.
Thanks in advance.
Shrikant
Edited by: Alvaro Tejada Galindo on Mar 17, 2008 1:56 PM

Hi ,
You have posted this question long back that is one and half year back nearly.
You got an error message in IW52 stating Object does not exist ( status management ).
Now iam also facing the same problem in iw22 transaction. Can you say me how you solved if you remember.

Iak file does not change channel config?

I am relatively new to Lab-View so please bear with me
I have multiple iak files setup for different vi's that require some different ranges on the AI-100 modules I am using (FP-1601 Ethernet module). My problem is when I start a vi, with the iak file path needed wired to the FP-open tag, it does not change the channel configuration from whatever is currently on the modules themselves.
Is this correct? I know I can get the channels to update to the iak file by opening it in FP explorer and editing the device clicking on the channel config and syncing to the file. This will be very tedious for the un-trained test monkey these different programs are designed for. Am I missing some option somewhere that syncs the modules t
o the iak file when you open a field point session?

From a program perspective, the IAK file is solely used to provide channel mapping information. From a FieldPoint Explorer (or NI-FP) perspective, the IAK file contains all channel naming information, communication mapping information and channel configuration information. In FieldPoint Explorer (3.0.2 or less), the only way to change the channel configuration between IAK's, is to switch IAK's in FP Explorer and right click on each (and every) FieldPoint IO Module, choosed Edit This Device and then choose Channel Configuration. When the dialog box asks you whether to use the Device or File settings, choose File. In NI-FP 4.0, there exists an option to download the entire configuration to an entire bank at a time, but there is still no method of downloading the co
nfiguration file programmaticly at run time.
However, another option in the form of the Ethernet Configuration VI's exists. They allow you to programmatically configure each channel (range & attributes). For an understanding of the range and attribute values, you can cross reference the FP-1000/1001 Programmers Reference Manual.
Regards,
Aaron
Regards,
Aaron

Turning off VM in guest does not update status in VMM 2012 R2 Update Rollup 2 console

I am seeing an issue with a few VMs where if you turn the VM off from within the guest OS, the status does not change in the VMM console.
Details about the environment:
Six node cluster running Server 2012 R2 Datacenter Core
Cluster validate completed successfully. Only warnings due to some VMs being offline
Virtual Machine Manager 2012 R2 with UR2
251 VMs in cluster used for Citrix XenDesktop and XenApp
I've read a few articles similar to this one that refer to a change in the VM Light Refresher schedule from RTM to SP1. (http://blogs.technet.com/b/chengw/archive/2012/09/17/update-on-vmm-refreshers-what-has-changed-and-what-this-means-to-you.aspx).
Basically it looks like the light VM refresher was turned off and now we depend upon WMI if the environment support WCF 3.0.
Does this mean that we're looking at the WMI on the Host or the Guest? Or, is it possible that I just have WMI corruption in a few guest VMs?
If I want to turn it back on, it seems like I should be able to create a registry DWORD key in HKLM\SOFTWARE\Microsoft\Microsoft System Center Virtual Machine Manager\Settings called VMPropertiesUpdateInterval and set the value. Does this seem plausible?
Would it be supported?

I specifically asked the product team about that.
And this has actually been the behavior all along. However, it was never my experience until after applying UR2.
And this is an experience vs. Product behavior thing. Somewhere in the process something changed with how the one is decided upon when vmm gets more than one match.
I am going to add this to my discussion with them.
Glad we have your issue resolved.
Brian Ehlert
http://ITProctology.blogspot.com
Learn. Apply. Repeat.
Disclaimer: Attempting change is of your own free will.

Object does not exist (status management)

Hi,
When I create a notification and click save button, I am getting the following error.
Object does not exist (status management)
Message no. IM258
Diagnosis
This refers to an error in central status management.
Task status
The central status management connection at task level will only be supported from Release 3.0.
For this reason, no task status is available for statuses created before changing to Release 3.0, and status change is therefore also not possible.
Procedure
In the case of task statuses of notifications in releases prior to 3.0:
When you save a notification you can create a status for the tasks.
In the case of notification or task statuses for notifications from Release 3.0:
Please refer to your system administrator.
thanks and regards
muru

Dear,
Please refer the OSS Note 437878 - Status data missing for PM/CS notifications .
Regards,
R.Brahmankar

Safari 5.0 - URL does not change when changing location

I have noticed this on two Macs running 10.6.3. When moving between pages (eg, clicking on a link within a page, or using the Google search bar to locate and load a new page), the URL in the address bar does not change to the new location. It remains at the
This applies whether the new page is within the same domain, or is at a different location.
Specific test: Load http://news.bbc.co.uk in Safari. Towards the top left of the page, there's a link to the BBC home page, which should appear in the status bar as "http://www.bbc.co.uk". Clicking on it will send you to that page, but the URL will remain as the news subdomain. If you click to another tab, then click back, it'll then update correctly.
Matt

Hi Matt,
MIght be corrupted Safari pref files.
Go to the Safari Menu Bar, click Safari/Preferences. Make note of all the preferences under each tab. Quit Safari. Now go to ~/Library/Preferences and move this file com.apple.safari.plist to the Desktop.
Relaunch Safari and see if that makes a difference. If not, move the .plist file back to the Preferences folder. If Safari functions as it should, move that .plist file to the Trash.
If the problem persists, go to ~/Library/Caches. From the com.apple.Safari folder move the "cache.db" file to the Trash. Relaunch Safari.
Carolyn

ICal does not update status when someone accepts my invitation

If I send a meeting request out from iCal, and someone accepts, their status in iCal does not change, i.e. in the event, the icon against their name remains as a grey question mark and does not change to a green tick. This is annoying because of course the whole point is to see who is or is not coming to your meeting!
Why is this please, and is there a fix?
(I have found references to this issue on here but they are from several years back. Just wondering if there has been a fix since then that I'm missing. Thanks.)

As if by magic it is now working. I went away from the mac for a couple of hours, came back and it started to work. This is scary as I would expect this kind of action on a Mickysoft machine but not a Mac. Ho Hum - at least the problem has been sorted even if I don't know how.
Chris

When I try to upload a file it goes through the correct proceedure, but does not change the remote file i.e.Index.htm

Hi
I have an uploading problem to the server. The problem is when I try to upload a file it goes through the correct proceedure,
but does not change the remote file i.e.Index.htm, or three stages1.htm.
My Localroot folder is C:\Gods Plan Web\
The site map layout is C:\Gods Plan Web\Index.htm
The folder for the remote site is /public_html/
Should the local root folder mirror the remote site, i.e./public_html/
if this is so, what should I put into the
(a) Local Root Folder box?
(b) site map layout box?
The FTP is performing well other than changing the intended file.

You should be uploading only the contents of your local root to the public_html folder (remote root).
The index.html you use as your site's home page needs to be in your site root. If you look at your Files window in DW, you should have something like the following...
Site - Whatever you named your site
     index.html
     images
     pages
          page1.html
          page2.html
If you have any folder between Site - and the index.html page, like...
Site - Whatever you named your site
     mywebsite
          index.html
It will upload to the public_html while still in that folder, so to find your page online, you would need to type something like...
www.mydomain.com/mywebsite
public_html should NOT appear within your local files and if it existed there, would cause a redundancy if uploaded. You would need to type www.yourdomain.com/public_html to see the uploaded pages.
If you could post a screen shot of your expanded Files window while connected to the server (just connect and click the Expand button in Files, don't drill down into any of the directories), we may be able to see the issue.

When I convert my pdf doc to word, the fonts go really weird and it also puts some text into boxes. when I try to select the test and change the font, it does not change it properly?

When I convert my pdf doc to word, the fonts go really weird and it also puts some text into boxes. when I try to select the text and change the font, it does not change it properly? This is making it impossible to amend.

Hi Janedance1,
If the PDF that you converted already has searchable text, please try disabling OCR as described in this document: How to disable Optical Character Recognition (OCR) when converting PDF to Word or Excel. (If the PDF was created from a scanned document and doesn't already have searchable text, disabling OCR isn't a great option, as the text won't be searchable/editable in the converted Word doc.)
Please let us know how it goes.
Best,
Sara

Tables are deleted but database size does not change in sql server 2008r2

Hi All,
20GB Tables are deleted in my database but database size does not change and disk size showing same size.

Hi ,
I have ran the Disk usage by Top Tables report and Identified couple of tables with unwanted data for last 5 years. I have deleted the data for the first 3 years and then ran the Disk usage by Top Tables report again. When I compared the report before
and after the data deletion, I have noticed certain facts which is not matching with what I know or learned from experts like you. The following are the points where I am looking for clarification:
1.Reserved (KB) has been reduced. I was expecting the data Reserved (KB) will remain the same after the data deletion.
2. The Data(KB) and Indexes(KB) fields have been reduced as expected. The Unused(KB) field have been increased as expected.
I was expecting the total of Data(KB) and Indexes(KB) field space gained will be equal to the Unused(KB) field gained after deleting the data. But that is not the case. When I deducted(subtracted) the difference in the Reserved(KB)(Difference before
and after data deletion) field from the Total of space gained from the data deletion is equal to the Unused(KB) gained field value.
I am not a SQL expert and not questioning but trying to understand whether we really gain space by deleting data from the tables. Also keen to get the concepts right, but my testing by deleting some records confused me.
Looking ahead to all your expert advice.
Thanks,
Vennayat

Error-IM258-Object does not exist (Status Management)

Dear All
We have used the enhancement "MCI10001" for triggering the external E mail while scheduling the maintenance plan using T code IP10.
System will fetch the E mail ID from the equipment master -partner function either Vendor or User responsible and sends the mail
But while executing IP10 system throws an error message as follows
Error Msg no: IM 258- Object does not exist (Status Management)
This refers to an error in central status management.
Kindly help on the above issue
Regards
Thyagarajan

l have same problem my code below
help me please .
if email is not INITIAL and ulke is not initial and sy-tcode eq 'QM01' and sy-ucomm eq 'BUCH' and I_VIQMEL-QMART = 'Q1'.
    CALL FUNCTION 'POPUP_TO_CONFIRM'
      EXPORTING
        TITLEBAR       = 'E-mail'
        TEXT_QUESTION = 'E-mail Göndermek istiyormusunuz ?'
      IMPORTING
        ANSWER         = answer
      EXCEPTIONS
        TEXT_NOT_FOUND = 1
        OTHERS         = 2.
if answer eq 1 and ulke = 'TR'.
lt_mailtxt ='Değerli Müşterimiz,'.
APPEND lt_mailtxt.clear lt_mailtxt.
lt_mailtxt = 'Şikayetiniz sistemimize alınmıştır. Müşteri şikayeti sorumlularımız sizlerle en yakın zamanda irtibata '.
APPEND lt_mailtxt.clear lt_mailtxt.
lt_mailtxt = 'geçeceklerdir. Şikayetiniz için teşekkür eder, saygılarımızı sunarız.'.
APPEND lt_mailtxt.clear lt_mailtxt.
lt_mailtxt =''.
APPEND lt_mailtxt.clear lt_mailtxt.
data: it_packing_list like sopcklsti1 occurs 0 with header line,
       it_receivers like somlreci1 occurs 0 with header line,
        gd_cnt type i,
        gd_sent_all(1) type c,
        gd_doc_data like sodocchgi1,
        gd_error type sy-subrc.
gd_doc_data-doc_size = it_packing_list-body_num * 255.
Populate the subject/generic message attributes.
gd_doc_data-obj_langu = sy-langu.
gd_doc_data-obj_name = 'SAPRPT'.
gd_doc_data-obj_descr = 'Naksan KGM'.
gd_doc_data-sensitivty = 'F'.
Describe the body of the message
clear it_packing_list.
refresh it_packing_list.
it_packing_list-transf_bin = space.
it_packing_list-head_start = 1.
it_packing_list-head_num = 0.
it_packing_list-body_start = 1.
describe table lt_mailtxt lines it_packing_list-body_num.
it_packing_list-doc_type = 'RAW'.
append it_packing_list.
CLEAR it_receivers.
it_receivers-receiver = email.
it_receivers-rec_type = 'U'.
it_receivers-com_type = 'INT'.
it_receivers-notif_del = 'X'.
it_receivers-notif_ndel = 'X'.
append it_receivers.
call function 'SO_DOCUMENT_SEND_API1'
       exporting
            document_data              = gd_doc_data
            put_in_outbox              = 'X'
            sender_address             = 'sinan.tataroglu@***.com'
            sender_address_type        = 'INT'
            commit_work                = 'X'
       importing
            sent_to_all                = gd_sent_all
       tables
            packing_list               = it_packing_list
            contents_txt               = lt_mailtxt[]
            receivers                  = it_receivers
       exceptions
            too_many_receivers         = 1
            document_not_sent          = 2
            document_type_not_exist    = 3
            operation_no_authorization = 4
            parameter_error            = 5
            x_error                    = 6
            enqueue_error              = 7
            others                     = 8.
IF sy-subrc EQ 0.
COMMIT WORK.
Push mail out from SAP outbox.
SUBMIT rsconn01 WITH mode = 'INT' AND RETURN.
ENDIF.
elseif ulke ne 'TR' and answer eq 1.
lt_mailtxt ='Dear Customer,'.
APPEND lt_mailtxt.clear lt_mailtxt.
lt_mailtxt = 'Your compliant has just entered to system. Customer complaint responsible will contact with you ASAP.'.
APPEND lt_mailtxt.clear lt_mailtxt.
lt_mailtxt = 'Thanks for your complaint.'.
APPEND lt_mailtxt.clear lt_mailtxt.
gd_doc_data-doc_size = it_packing_list-body_num * 255.
Populate the subject/generic message attributes
gd_doc_data-obj_langu = sy-langu.
gd_doc_data-obj_name = 'SAPRPT'.
gd_doc_data-obj_descr = 'Naksan KGM'.
gd_doc_data-sensitivty = 'F'.
Describe the body of the message
clear it_packing_list.
refresh it_packing_list.
it_packing_list-transf_bin = space.
it_packing_list-head_start = 1.
it_packing_list-head_num = 0.
it_packing_list-body_start = 1.
describe table lt_mailtxt lines it_packing_list-body_num.
it_packing_list-doc_type = 'RAW'.
append it_packing_list.
CLEAR it_receivers.
it_receivers-receiver = email.
it_receivers-rec_type = 'U'.
it_receivers-com_type = 'INT'.
it_receivers-notif_del = 'X'.
it_receivers-notif_ndel = 'X'.
append it_receivers.
call function 'SO_DOCUMENT_SEND_API1'
       exporting
            document_data              = gd_doc_data
            put_in_outbox              = 'X'
            sender_address             = 'peykan.samli@****.com'
            sender_address_type        = 'INT'
            commit_work                = 'X'
       importing
            sent_to_all                = gd_sent_all
       tables
            packing_list               = it_packing_list
            contents_txt               = lt_mailtxt[] "it_message
            receivers                  = it_receivers
       exceptions
            too_many_receivers         = 1
            document_not_sent          = 2
            document_type_not_exist    = 3
            operation_no_authorization = 4
            parameter_error            = 5
            x_error                    = 6
            enqueue_error              = 7
            others                     = 8.
IF sy-subrc EQ 0.
COMMIT WORK.
Push mail out from SAP outbox.
SUBMIT rsconn01 WITH mode = 'INT' AND RETURN.
ENDIF.

In Adobe Acrobat X Standard, our user used to be able to resize drawings to 8.5 x 10, it stopped working yesterday. It allows her to do this without an error but the size does not change?

In Adobe Acrobat X Standard, our user used to be able to resize drawings to 8.5 x 10, it stopped working yesterday. It allows her to do this without an error but the size does not change?

Try unmounting the volume on your iMac using Disk Utility. Then mount it again. You may need to reboot the laptop or relaunch its Finder process (using the Force Quit window) after remounting the drive on your iMac. Remember that no process may be accessing any files on the drive you plan to unmount, or the unmount will fail. Unmounting and remounting an external drive on my iMac made it become visible on my MacBook Pro after it had disappeared.

I am unable to redeem my purchase of a Photoshop Elements 12 software license. After entering the redemption code and clicking on the Redeem button, nothing happens. No error message. Screen does not change.

I am unable to redeem my purchase of a Photoshop Elements 12 software license. After entering the redemption code and clicking on the Redeem button, nothing happens. No error message. Screen does not change.

try using a different browser, or contact support Contact Customer Care

Fieldpoint FP-RLY-422 does not change status

Similar Messages

Maybe you are looking for