File system configuration

Hi,
I want to install ecc6.0 on linux with db2,how to configure the file system.
Thanku

Download the official installation guides at
http://service.sap.com/instguides
Markus

Similar Messages

Was advised to delete system configuration file from hard drive and now computer will not start - any help would be appreciated.

Downloaded Yosemite and since then cannot connect to internet or bluetooth mouse - was advised to delete system configuration file from the hard drive and since then cannot start up computer. Any help would be appreciated - cheers.

Boot the MBP with the OPTION+COMMAND+R keys down. The result should be a display showing a revolving globe. By following the instructions, you will be able to reinstall the original OSX. Then you may reinstall Yosemite.
A solid Internet connection will be required.
Ciao.

I am trying to resize disk space on parallels 6 for windows XP under configure Hardrive and I get the error resizing failed unable to resize last volume the file system of this volume might be damaged or not supported? I am on a Mac using Parallels 6

I have been trying to increase my disk space for windows xp on my Imac and I am running parallels 6. before opening windows I go into configure in parallels and open the hard drive and try to move the allotted disk space from 32 gig to 64 or any other increased gig and then apply and I get the error message: resizing failed unable to resize last volume. The file system of this volume might be damaged or not supported. How do I increase the size?? I just also did a disk repair utility with Apple on the Apple side of my IMAC. Please Help!! I had uninstalled SQL server on the windows side and needed to uncompress files to install this and then I ran short on disk space.

This sounds to me that your Parallels XP file system is corrupted and not the OSX file system.
Have you checked the XP file system while running the Parallels XP yet ?
However, it would be better to ask such question in the Parallels Forum http://forum.parallels.com/
Stefan

Is there a way to configure NTFS file system on an NSS 324 SmartStorage unit. So far I can setup ext 3 or ext 4 but no option for NTFS

Is there a way to configure NTFS file system on an NSS 324 SmartStorage unit. So far I can setup ext 3 or ext 4 but no option for NTFS. This unit should be joining a Windows Server 2008 R2 network and needs to be shared with all users. This unit will replace a File server running Win 2003 SP2.
Message was edited by: Hermann Koster
Thank you very much for your reply. The idea is to decommission the Windows file server which is running Windows Server 2003 SP2 operating system but is not running as a DC but just a member server. All this server is doing is providing file server services so my idea is to replace it with the NSS 324 box. My only concern is that when my NSS joins the domain all my users would be able to see and access network shares transparently, the same way they saw the former W2003 file server. After I transferred the data from File server I will use the same for NSS that was used for file server as well as same IP address and folders path as before.
Any suggestions or advice?
Once again thank you very much for your reply.
Cheers,

The internal HDDs must be formatted in either EXT3 or EXT4 file system because NSS uses Linux OS. This is mainly because the RAM designed to fit with the customized Linux OS's size.
You can connect to an external HDD via a USB or eSATA port. The external HDD's file system can be NTFS, FAT32, AFT or EXT3/4 to be recognized for read/write. You can connect a 2TB USB/eSATA drive connec to the NSS via USB port to format your HDD for NTFS, AFT, FAT32, or EXT3/4 partition.
You can join the NSS to a Windows domainr so all domain users to access NSS. You cannot replace the NSS for the Windows 2003 SP2 server. They are two different products and do different jobs. Windows server is features sets server while the NSS is the files/data server.
Hope that helps!!

The Em Key is not configured properly or is corrupted in the file system and doe s not exist in the Management Repository.

I'm getting this error and is there any way to resolve this without re-creating the service/s again, etc. Just curious if there are any suggestions/steps I may have missed, if not, I'll drop and recreate the services again
Anyway, I have a backup of the emkey.ora and put it in the sysman/config directory, but still doesn't work... please see below...
C:\Documents and Settings\abigail>emctl status emkey
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
Please enter repository password:
The Em Key is not configured properly or is corrupted in the file system and doe
s not exist in the Management Repository. To correct the problem:
1) Copy the emkey.ora file from another OMS or backup machine to the OH/sysman/c
onfig directory.
2) Configure the emkey.ora file by running "emctl config emkey -emkeyfile <emkey
.ora file location>".
C:\Documents and Settings\abigail>emctl config emkey -emkeyfile E:\app\abigail\p
roduct\11.2.0\dbhome_1\sysman\config
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
Please enter repository password:
The Em Key is already configured. To override the current configuration, run "em
ctl config emkey <options> -force".
C:\Documents and Settings\abigail>emctl config emkey -emkeyfile E:\app\abigail\p
roduct\11.2.0\dbhome_1\sysman\config -force -sysman_pwd ********
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
The Em Key could not be configured. Unable to access file E:\app\abigail\product
\11.2.0\dbhome_1\sysman\config.
C:\Documents and Settings\abigail>emctl secure dbconsole -sysman_pwd ********
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
http://ABIGAIL:5501/em/console/aboutApplication
DBCONSOLE already stopped...   Done.
Agent is already stopped...   Done.
Securing dbconsole...   Started.
Please enter repository schema password:
Securing dbconsole...   Failed.
EMKey is misconfigured.

Sorry but I'll have to ignore your suggestion, and don't worry about how I spend my time
AND OHMYGODD IT WORKSS!!! For future reference, this is how I solved it based on my searches, actually based on one particular search:
http://franjv.blogspot.com/2013/08/emkey-problems-in-oracle-rac-11gr2.html
Thank youuu whoever wrote that and... is it the same "Fran" who helped me the last time?!? Coincidence??
ANyway, thank youuuu

PI 7.1: Transport configuration using the file system

Hi!
How can I transport the configuration objects from DEV to QA, when I have different business systems in DEV and QA (BS_dev and BS_qa)?
I use individual landscapes per system (DEV, QA and PROD).
What have i done?
1. Export the software componet version from DEV/SLD in a file. --> ok
2. Import in the QA/SLD --> ok
3. Export of the objects from DEV/ESR in a file --> ok
4. Import in QA/ESR -->
5. Export of the objects from DEV/ID in a file --> ok
6. Import in QA/ID --> error (different business systems)
Thanks in advance!
Edgar

Hi.
There are two ways to transport ID and IR Object to transport .
1. CTS + : Totally automated Way .,
2. .tpz : Manual Lagacy Import / Import way .
Now . Steps .are :
There are two types of transport mechanisms in XI/PI.
1. File Transport System.
Files are imported and exported into SAP XI OS Level for Development and Quality Server,
This Process is risky as there is no automated system and there is no track record of imported or Exported Files,
as in this syetem exported files are transported to QA System from DEV System.
file Extension in file transport System : - .tpz
2. Through CTMS(Change Transport Managment System).
GUI Based tool, Installed on SAP XI BOX, This system provides the automated transport system , which keep tracks of transported Objects and Failed objects.
There are initial level efforts to set up transport system.
Transport Procedure for Various System :-
DESIGN OBJECTS ---> (ENTERPRISE SERVICE REPSITORY OBJECTS) -
> INTEGRATION BUILDER.
Step -I
1. Select NameSpace to trasport.
2. Right Click on NameSpace to Transport.
3. Select Export Option.
4. Check or Select the Software Component Version.
5. Check the Mode of transport.
CTS MOde:-
5.1 Select a required type of Object Set:
IN OUR CASE: ALL OBJECT OF INDIVIDUAL NAMESPACE.
5.2 Select Transort request.
5.3 Finish the Process.
TRANSPORT USING FILE SYSTEM:-
5.1 Select a required type of Object Set:
IN OUR CASE: ALL OBJECT OF INDIVIDUAL NAMESPACE.
5.2 Finish the Process.
Step II
1. GO TO TOOLS OPTION IN MENU BAR
2. OPEN CTS TRANSPORT ORGANIZER
3. Select the request to Release.
4. Press Button Release.
Step III( Steps to be Perform at Target System).
1. Execute Transection Code STMS.
2. Check your Transport Request Number.
3. Focus on that Trasport Request Number Through Mouse.
4. Now Import The Transport Request on Specific client of Target System.
5.Click Ok.
FINAL :- NOw on Quality Server all Transported Objects Need to be activated.
CONFIGURATION OBJECTS ---> (INTEGRATION DIRECTORY) -
> INTEGRATION BUILDER.
Step -I
1. Select Configuration Scenario to trasport.
2. Right Click on Configuration Scenario to Transport.
3. Select Export Option.
4. Check or Select the Configuration Scenario.
5. Check the Mode of transport.
CTS MOde:-
5.1 Select a required type of Object Set:
IN OUR CASE: ALL OBJECT OF Selected Scenario.
5.2 Select Transort request.
5.3 Finish the Process.
TRANSPORT USING FILE SYSTEM:-
5.1 Select a required type of Object Set:
IN OUR CASE: ALL OBJECT OF Selected Scenario.
5.2 Finish the Process.
Step II
1. GO TO TOOLS OPTION IN MENU BAR
2. OPEN CTS TRANSPORT ORGANIZER
3. Select the request to Release.
4. Press Button Release.
Step III( Steps to be Perform at Target System).
1. Execute Transection Code STMS.
2. Check your Transport Request Number.
3. Focus on that Trasport Request Number Through Mouse.
4. Now Import The Transport Request on Specific client of Target System.
5.Click Ok.
FINAL :- NOw on Quality Server all Transported Objects Need to be activated( CHANGE OBJECTS).
Regards,
Venkata S Pagolu

Oracle DB and File system backup configuration

Hi,
As I understand from the help documents and guides, brbackup, brarchive and brrestore are the tools which are used for backing up and restoring the oracle database and the file system. We have TSM (Trivoli Storage manager) in our infrastructure for managing the backup centrally. Before configuring the backup with TSM, I want to test the backup/restore configuration locally i.e. storing the backup to local file system and then restoring from there. Our backup strategy is to have full online backup on the weekends and incremental backup on the weekdays. Given this, following are the things, I want to test.
1. Full online backup (to local file system)
2. Incremental online backup (to local file system)
3. Restore (from local file system)
I found help documents to be very generic and couldn't get any specific information for the comprehensive configuration to achieve this. Can someone help with end to end configuration?
We are using SAP Portal 7.0 (NW2004s) with Oracle 10g database hosted on AIX server.
Helpful answers will be rewarded
Regards,
Chandra

Thanks for your feedback. I am almost clear about this issue now, except one point need to be confirmed: do you mean that on linux or unix, if required, we can set "direct to disk" from OS level, but for windows, it's default "direct to disk", we do not need to set it manually.
And I have a further question: If a database is stored on a SAN disk, say, a volume from disk array, the disk array could take snapshot for a disk on block level, we need to implement online backup of database. The steps are: alter tablespace begin backup, alter system suspend, take a snapshot of the volume which store all database files, including datafiles, redo logs, archived redo logs, controll file, service parameter file, network parameter files, password file. Do you think this backup is integrity or not. please note, we do not flush the fs cache before all these steps. Let's assume the SAN cache could be flushed automatically. Can I think it's integrity because the redo writes are synchronous.

How to configure a QFS file system on RAID5 disk in Sol 10 sparc

Hi Forum,
I am setting up Sun cluster 3.2 for oracle RAC on solaris Sparc system (2 node setup)
I have a SAN disk of emc clarrion which is a RAID 5 disk.
For Oracle clusterware to install it needs QFS file system so i also downloaded sun storedge QFS (refering to sun DOC)
When i try to mount the samfs filesystem
bash-3.00# samsharefs Data
samsharefs: Filesystem Data not mounted
bash-3.00# sammkfs Data
Building 'Data' will destroy the contents of devices:
/dev/dsk/c3t60060160F6B02000760677FF21FCDD11d0s4
/dev/dsk/c3t60060160F6B02000760677FF21FCDD11d0s5
Do you wish to continue? [y/N]y
total data kilobytes = 104857600
total data kilobytes free = 104857536
total meta kilobytes = 104857600
total meta kilobytes free = 104856192
bash-3.00# samfsinfo Data
name: Data version: 2
time: Thu Feb 19 20:05:32 IST 2009
count: 2
capacity: 0000000006400000 DAU: 64
space: 00000000063fffc0
meta capacity: 0000000006400000 meta DAU: 16
meta space: 00000000063ffa80
ord eq capacity space device
0 20 0000000006400000 00000000063ffa80 /dev/dsk/c3t60060160F6B02000760677FF21FCDD11d0s4
1 21 0000000006400000 00000000063fffc0 /dev/dsk/c3t60060160F6B02000760677FF21FCDD11d0s5
bash-3.00# mount /db_qfs
mount_samfs: Non shared fs and shared are mutually exclusive.
When i try to mount the file system i get the above message.
Kindly suggest appropriate steps to resolve this issue.
Regards
Prakash

As per the usual setup of a shared SAN disk. The file system used is UFS. when i started installing oracle clusterware i came to a point where i had to run root.sh. the error i got was UFS filesystem not supported.
So now i get stuck in deciding which filesystem oracle clusterware would support. As i had the sun storedge QFS file system setup in the document i continued to follow it.
If you have any steps for configuring oracle clusterware to use the UFS file system it would be an additional help. As i have the UFS file system setup ready at my end.
Regards
Prakash

Error in configuring Windows File System Repository

Hi All,
While trying to configure Windows File system repository we are getting the following error
1. Getting this error when we give
<ip address>\<shared folder name>
Startup Error: The localroot does not exist:
10.1.100.44\Shared_folder
2. Getting this error when we give
<ip address>
Startup Error: host is unkown in file path '
10.1.100.44' - invalid network path:
10.1.100.44
Could any one help in solving this issue.
Regards,
Sravanthi

Hi Chiluveru Sravanthi
According to the documentation, there is a difference between the path syntax for the repository manager and the network path. Did you pay attention to this difference when doing your configurations?
Network paths (Network Path)
Specifies the path to the Windows remote server.
The path consists of the IP address of the Windows remote server, and a path specification.
For example,
192.168.0.1share
Alternatively, you can enter the UNC name and path of the server, for example,
servershare.
SAP recommends that you specify the IP address, since you can then check the availability of the server more easily, using the ping command.
Note: It is not sufficient to enter the server name alone. Specifications in the form of c$ cannot be resolved either.
http://help.sap.com/saphelp_nw70/helpdata/EN/63/7f283ac3d7c54b94964931fa1b4ed9/frameset.htm
File System Repository Manager (Root Directory)
This denotes the path to the root directory in the file system to which the repository manager is assigned.
If you want to integrate documents from a Windows system, this can be a drive letter (followed by a colon) or directory path on the local server or a remote server share (for example, //myserver/myshare/somedir).
If you are running your portal on UNIX and want to access the file system on another UNIX host, you must mount the required directory on the portal server.
Example path when using a UNIX system:
/usr/company/share
The repository manager is responsible for the specified directory and all its subdirectories.
Note that multiple repository manager configurations are not allowed to have the same subpath in their Localroot parameter.
http://help.sap.com/saphelp_nw70/helpdata/EN/e3/92322ab24e11d5993800508b6b8b11/frameset.htm
Best regards,
Martin Søgaard

I deleted the System Configuration files and now my WiFi won't work.

I've always loved Apple but ever since I upgraded to Yosemite I've been having problems with my WiFi connection, it kept dropping. So I decided to look for a solution and I found some forums that said I should go to System Configuration on Finder (Cmd+Shift+G on Finder, then write /Library/Preferences/SystemConfiguration) and that I should delete all the files there. I did just that and now I can't get online at all. Then I read in some other forums that you should only delete certain files... So you can imagine my face when I read that. I tried taking the files I deleted out of the Trash and everything but I still can't connect to the Internet wirelessly. I'm desperate!
My wireless connection used to drop every 2 minutes, and I had to go to Network Preferences, Assistant, Diagnostic, and that would fix it for another 5 minutes, 10 if I was lucky. But now I can't get online at all. I've tried everything I could think of and nothing.
I don't care if my Internet drops anymore, I just want it to go back to the way it was. I'm traveling to Argentina in a week and I need this fixed!!
If anyone can help me I would really appreciate it.

The following support article is somewhat outdated. Where it refers to booting from an installation disc, you should boot into Recovery (if running 10.7 or later) by holding down the key combination command-R at the chime. If your startup volume is encrypted with FileVault, you’ll have to unlock it in Disk Utility before you can do anything with it.
Mac OS X: Gray screen appears during startup

Cannot configure Oracle Cluster File System (OCFS2)

Dears,,
While trying to use ocfs2console to Configure Oracle Cluster File System (OCFS2)
Error appear to me as following:
Could not start cluster stack error.This must be resolved before any OCFS2 filesystem can be mounted.
How can solve this please?
thanks & regards,,

Dear all ,,
My issue solved now . . .
Really , it is strange.
Once , i added /sbin in .bash_profile under ~ Directory as following . . .
export PATH=$ORACLE_HOME/bin:$ORA_CRS_HOME/bin:/bin:/usr/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/X11R6/bin
Then log out then back again.
After this change , i able to run ocfs2console successfully.
Hope this help you.
Thanks for all,,
Best regards,,

Configure Windows file system repository in local portal system

Hi
can any one give the step by step explanation for Configuring windows file system repository in local portal system .
Thanks
Kirankumar M

Hi Kiran,
Go Through all the docs, It will help you.
https://www.sdn.sap.com/irj/sdn/wiki?path=/display/KMC/File%2bSystem%2bRepository%2b-%2bW2KSecurityManager
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/284
http://help.sap.com/saphelp_nw04s/helpdata/en/e3/92322ab24e11d5993800508b6b8b11/frameset.htm
Anyways you have to
1. create a mapping in your windows by Tools -> Map Network Drive (say v:\)
2. Do all the configuration in your portal as per the 3rd link provided like network path and all.
3.Logon to portal with admin perrmission,
then
System Administration -> System Configuration ->Knowledge Management -> Content Management ->Repository Managers -> File System Repository
Configure a new repository manager for your windows system.
Regards
Manisha

Configuring windows file system repository in local portal system(KM)

Hi
can any one give the step by step explanation for Configuring windows file system repository in local portal system .
Thanks
Kirankumar M

Hi Kiran,
Go Through all the docs, It will help you.
https://www.sdn.sap.com/irj/sdn/wiki?path=/display/KMC/File%2bSystem%2bRepository%2b-%2bW2KSecurityManager
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/284
http://help.sap.com/saphelp_nw04s/helpdata/en/e3/92322ab24e11d5993800508b6b8b11/frameset.htm
Anyways you have to
1. create a mapping in your windows by Tools -> Map Network Drive (say v:\)
2. Do all the configuration in your portal as per the 3rd link provided like network path and all.
3.Logon to portal with admin perrmission,
then
System Administration -> System Configuration ->Knowledge Management -> Content Management ->Repository Managers -> File System Repository
Configure a new repository manager for your windows system.
Regards
Manisha

CC configuration causes freezing and file system corruption

I have received no response for:
http://forums.adobe.com/message/6074118
It is a major issue, can I file an issue/fix request somehow?
Basically it appears that the default configuration when installing the complete product suite causes the OS (OSX Mavericks) to freeze unpredictably and render the system unusable unless shut down and rebooted. This may result in file system corruption and data loss requiring complete reinstall of OS and all products.
Some have mentioned 'drive' is causing this, but I am not familiar with that component and do not see any options to remove or disable such a product in CC.
I do not want any non-essential add-ons (like Bridge?) - just a reliable production configuration so I can get work done.
The risk of having the system 'locked up' or file system corrupted is unacceptable.
Thanks,
Mike

Hi mkrjf,
Please enable root account and try to use Photoshop and let me know if still the same behavior.
Root: http://support.apple.com/kb/PH14281
Regards,
Romit Sinha

Safe way to edit system configuration files?

What is a safe way to edit a system configuration file? I mean I did this twice: I edited rc.conf, rebooted and the system failed to boot. Then I had to edit out the typos with a LiveCD.
Is there like a visudo (that edits /etc/sudoers) for rc.conf, xorg.conf, fstab and so on?
Thanks!

Majorix wrote:
No I am of course editing those files with sudo. But the problem is, gedit won't check the file for possible errors, thus if you too oversee it and try to reboot using those system files, you will fail.
visudo checks you while you edit, so if you make an error it will warn you in the end.
I was asking if there was a similar tool for the rest of the configuration files.
Sorry for not being clear.
Oh -- a kind of a babysitter, you mean?
j/k, i screw up config files all the time.
No, as far as I know there is nothing like that for most files. some do have functionality like that, like I think lilo warns you when you write to lilo.conf and the file has errors. and you can run something like testparm for the smb.conf file, and I think there something similar to check apache config files, etc. but for the standard system config files or arch-specific files like rc.conf, fstab, etc. I don't think there is anything. you just have to be sure not to make any mistakes!

File system configuration

Similar Messages

Maybe you are looking for