Final Cut 5 and HDV-HCR camera

I have a new sony HDV-HCR camera and final cut pro 5. My tapes that have been recorded in HDV will log and caputure on my computer but the tapes that are recorded in DV will no show on my computer. I can work the camera but when I log and capture I always get the preview disabled on my screen. It says the VTR is ok and I have changed the camera settings to DV and use the dv ntsc settings on Final cut pro. HELP

Andres - welcome to the discussions - rendering is usually required when a clip's settings (resolution/codec/framerate/etc...) doesn't match the settings in the timeline. Using Easy Setup for your project's particulars and creating a new sequence is the often the best way to start out.
To check your clip's settings, ctrl-click on it in the browser and select Properties/Format... - to check your sequence, do the same or select Settings... and check there.
Patrick

Similar Messages

Final Cut doesn't see camera? Please help!!

So i'm opening final cut and i have my camera turned on and plugged up, but it says it can't see it. System Profiler sees it, as well as iMovie. Is there something i have set wrong? I've deleted preferances and everything. It just won't see the camera. the strangest thing was i got it to control the camera but, there was still no video when i would log and capture.
can anyone help?
Tedd

Done any QT or FCP upgrades lately? If so, check out this thread on deleting and reinstalling QT
http://discussions.apple.com/thread.jspa?messageID=1063612&#1063612
rh

How to Uninstall older version of Final Cut and Motion

Hello
I have a older academic version of Final Cut and Motion. I ordered a Full blown version of Final Cut Studio 2 that should arrive this week. How do I uninstall my old version of software? I don't want them conflicting with the new version.
My other question deals with performance. I'm running a Dual 2.5GHz G5 with 6G of ram. Video Board is the ATI x800XT. Will this system work for editing HDV or am I going to need to buy a new Intel based computer? I really don't want to spend 4K for a new system.
Thanks
Bob M

have a gander a Jon Chappel's FCS Remover over at Digital Rebellion
http://www.digitalrebellion.com/fcs_remover.htm

Final Cut locks up when camera is plugged in

I am using Final Cut Pro and it works just fine until I plug in my camera(canon optura 20) and then the program locks up. If I unplug the camera then everything is fine and it works again. This is a recent problem and has started happening in the past week. I have used this camera many times with final cut and it has worked just fine. Any help would be greatly appreciated. Thank You.

Based upon the information provided (Canon camera, FCP and Mac computer) - if you have any external firewire drives attached, shut down the computer and disconnect all the drives from the computer. Connect the camera to the computer, power it up then start up the computer. Launch FCP and attempt to capture to an internal drive (you said you have a MacPro).
Does it work now?
If so, you are the lucky victim of Canon's long standing firewire protocol problems. There are three solutions for the long term.
1. Never have an external firewire drive attached when the camera is in use.
2. Acquire a DV/DVCAM VTR (or non-canon camera) to use as the capture device.
3. Install an aftermarket firewire card to create a second firewire bus to isolate the camera from the drive. This only works with MacPro and MacBookPro computers.
If this isn't your problem, more information is required.
x

Final Cut and QT can't view/edit PAL HD footage recieved from Germany...

Final Cut and QT can't view/edit PAL HD footage I recieved from Germany - I spoke to filmer and he told me that it is HDV 1080i50.
I downloaded program VLC and was able to view the footage through there.
When I import it into FCP, it ether shows a black screen or crashes immediately - in QT, it only shows a white screen.
I have downloaded the QT plugin for MPEG movies.
PLEASE HELP!!!

If it's MPEG-2, chances are its a muxed file. You should be able to use MPEG Streamclip to demux and convert the file into whatever format matches your FCP Sequence specs.
But 1440 x 81? That doesn't sound right at all.
-DH

Final Cut and After Effects "file is busy"

Hello All-
I am running Final Cut Pro 5.1.4 and After Effects 7.0.1 Pro (on OS 10.4.8) and I have a question. I have a series of After Effects animated DV Quicktime clips edited together in Final Cut, and when I make changes to the After Effects project files and try to rerender, I get an error:
After Effects error: unable to overwrite - file is busy (delete) (-47) ( 3 :: 3 )
It's like Final Cut is "holding onto" the files and not allowing After Effects to rerender them. If I close down Final Cut, I can rerender just fine, but this gets real annoying closing it down and restarting it every time I need to rerender a clip. The problem is, because of my workflow, I need to do this dozens of times a day with clients in the room and I'm spending a lot of time closing and restarting Final Cut over the course of a day... is there way to do this without closing down Final Cut?
I assigned After Effects to be the "External Editor" for "Video Files", and used Final Cut's "Open In Editor" command. It sends the quicktime file to After Effects (not exactly what I want) and you would think that at this point Final Cut would have relenquished its access to the file so that I could rerender in After Effects, but nope, I still get the error. I have tried this with the User Preference setting "Always Reconnect Externally Modified Files" both on and off, no difference. I have also tried "Embed Project Link" in After Effects's quicktime output options, but this didn't help anything (I believe this only affects other Adobe apps).
The weird part of this is that when I drop a Photoshop file onto the Final Cut timeline, I can do "Open in Editor", it throws it to Photoshop, I can alter it and save with no problem, and pop back into Final Cut and it will be updated. But no such luck with Quicktime files and After Effects.
Let me know if there is a solution to this, or if I am stuck having to shut down Final Cut every single time I need to rerender one of the After Effects animation clips in the timeline.
- Bob Wilson
MacBook Pro 2.33ghz Core 2 Duo 15" Mac OS X (10.4.8) 3 gigs ram, 160 gig HD

What i have to suggest is more of a work around than it is a solution. i've had this problem off and on as well. What i do is add a number to the name of the newly rendered file, (ie. "monkey_throwspoo2.mov") import that file into FCP, open it in the viewer, and then copy it (apple + c). Provided it's the smae length as the previous file, you can right click on the previous file in the timeline and paste attributes, making sure to click on the content button for video (and audio if there is any). This should replace the old file in the timeline with the new one. Granted, you end up having a bunch of files that you're not using, but it's faster than restarting Final Cut (and looks more like it's something you're doing on purpose rather than a problem with the program to your clients). Hope this helps.
Craig

Using still images with Final Cut (and the apple suite in general)

I have had a re-occuring and long term problem that has caused me many lost hours of head scratching and work arounds, and as of yet I have not been able to come up with a good solution.
Its to do with integrating still images with the Final Cut suite.
If I receive a high quality image from a client to use in their video and I then try importing it into Final Cut and animating it, it always ends up looking like a pile of ahem. Often I will get "swimming" lines appear across fine detail on the image, and parts of it will flicker as it moves across the screen. For instance, if I have a picture of some blinds or other fine detail (especially horizontal and vertical lines), when I add a grow and throw movement to it the detail will become very noisy - buzzing and flickering like mad.
I have found I can counter this by resizing the image in photoshop to a resolution closer to SD video (700w or 500h) - but I always end up losing detail, and the flickering and noise is only reduced, not eliminated. Other things that have helped are blur effects applied at a very low level, like 0.5 blur, so its not noticeable visually, but Final Cut seems to treat it differently and quieten the noise and flicker down.
However, all of these workarounds are ultimately still giving a reduced quality product.
Also, this problem is not necessarily constrained to Final Cut, I am currently fighting DVD Studio Pro because it is murdering the text quality in a stills slideshow I am creating - and in this situation there is no animation being applied. No matter what file type (psd, jpeg, tiff, png...) or size I output the text and images from Photoshop in, the moment DVD studio pro gets hold of it, it turns to cripe.
For a while I was putting it down to the fact that I usually edit in SD (PAL) formats, and there just wasn't the resolution available to reproduce fine detail. However, I do often see other people achieving pin-sharp fine detail on still images and text in SD formats (the Apple templates are a good example)
So, my question to you, oh great and high boffins, if you are dealing with still images and text, how do you do it? How do you work around any noise problems you have, and how do you produce those pin-sharp images (both moving and still) I see in other professional productions?
Quad G5 Mac OS X (10.4.8)

still images with too high a resolution will always cause problems. this is due to the detail of the image being finer than the scanline of the tv can display ... obviously this will caise the image to flicker as these details alternately appear and disappear as and when the scanline can display them. as you have discovered, the answer is to apply a very small blur, the effect being that the detail is spread by the blur such that the scanline can dislay it correctly.
text issues are often rooted in the same problem ... unless the text is placed very carefully (whole even number on the y axis) then the quality may be impaired due to the resulting interlacing/scanline issues

Ok, I thought I could do a project in my new Final Cut Pro X. I got everything downloaded on Final Cut and I made my Project. The problem is is has taken so long to render that I don't have time. How do I download the video from Final Cut to Imovie?

ok, I thought I could do a project in my new Final Cut Pro X. I got everything downloaded on Final Cut and I made my Project. The problem is is has taken so long to render that I don't have time. How do I download the video from Final Cut to Imovie?

Your media is stored in Final Cut Events folder > "name of event" > original media. The Final Cut Events folder is in your movies folder or at the root level of an external drive if you are using one to store your media. Simply open iMovie and under file menu select import movies. Navigate to the original media folder and import your clips to Imovie event library.

Hi, I downloaded the app for macbook "Lens Flare for Final Cut" and I've struggled a lot to install this app at final cut . Someone could help me ? i´m from Mexico i speak spanish

Hi, I downloaded the app for macbook "Lens Flare for Final Cut" and I've struggled a lot to install this app at final cut . Someone could help me ? how i can install this app in Final Cut? this app cost me money and not is working to me, i am disappointed sorry if a write bad, i´m from Mexico i speak spanish

This is a user2user board for FCPX - maybe better you discuss your issues with the makers of that 'plug in'
Seems for me a bit 'fishy', isn't it? - other professional plug-in makers deliver with an installer... That advice at AppStore, how to install it, is ... rare:
How install it ? – click the launch button. Motion 5 will start itself. When Motion is open click save as. Write a generator name - Lens Flare and choose category RGB HOUSE or make it. Click Publish and you are done. If you don’t have Motion 5 look at support site - how to install in FCP.
How it works ? – In Final Cut Pro you will find in Generators RGB HOUSE group, where will be Lens Flare. Drag this generator above all clips in timeline. When it’s there remember to change blending mode to Screen (in video section). You can adjust color, steak color, glow, intensity, scale - apacity and blur of artifacts, position. Any parameter could be stored as a keyframe, so You can easily animate the flare.
so, I don't speak Spanish, lets have some fun with translate.google...:
Cómo instalarlo? - Haga clic en el botón de inicio. Motion 5 comenzará Misma. Cuando el movimiento está abierto clic en Guardar como escribir un generador de nombres -. Resplandor del objetivo y seleccionar categoría RGB CASA o hacerlo. Haga clic en Publicar y ya está. Si usted no tiene el movimiento 5 vistazo a sitio de soporte - cómo instalar en FCP.
Cómo funciona? - En Final Cut Pro se encuentra en el grupo generador RGB CASA, donde serán destello de lente. Arrastre este generador por encima de todos los clips en la línea de tiempo. Cuando es allí te acuerdas de que cambiar el modo de fusión a la pantalla (en la sección de vídeo). Usted puede ajustar el color, color carne, brillo, intensidad, escala - falta de definición apacidad y artefactos de su posición. Cualquier parámetro podría almacenarse como un fotograma clave, por lo que puede animar fácilmente la antorcha.
Hope it makes at last a little sense... I don't trust these automatic translators
(the German translation is ... awesome funny!)
Finally: it's from 2012! Needs probably an update - contact the dealer!

Can I share files from other programs or just Adobe apps files. I work with Final Cut and Premiere X

Can I share files from other programs or just Adobe apps files. I work with Final Cut and Premiere X.? Need to share files up to 6GB.
I need to know if the 20 gb limit is about all that I share, or if it's just about whatis in the clouds. If I take, recover my limit?
The speed of upload e download is good?

The Creative Cloud file storage could be used for video assets but speed and performance might vary based on location. I would suggest you testing it out yourself using your Adobe ID before subscribing. Performance would not change after you joined.
-Dave

Final Cut and Serial Number

I had Final Cut Studio 5.1 intalled on my Powerbook G4. Then, my computer was sent in and I was without for a month. So while it was away, I put Final Cut Pro on my home computer to finish my film for school. When I got my laptop back, I tried uninstalling Final Cut Pro on my home computer, but didn't have the installation disk, so I just simply trashed the 'Final Cut Studio System ID' on my home computer so that I couldn't use the program.
So, now Final Cut works fine on my Powerbook. But, I accidently updated to 5.1.4 - while my school computers are still on 5.1.2. So I wanted to uninstall Final Cut, and then re-install it so that the applications would be compatable. But, when I insert my Final Cut Studio Installation Disk, it asks for my serial number, which I put in - but the 'Continue' button never lights up.
I also went to the website to register my product so that I could download the 5.1.2 update...entered my serial number and it told me it was an invalid number.
I'm entering the exact same number in the exact same way that I originally did on my Powerbook. Is there anything I can do? The only time the serial number has ever been on another computer before was when it was on my home computer, but I hadn't registered it, and then I removed it - so my laptop is the only computer I have Final Cut on. Why isn't this working? It's quite frustrating when I need an edit for my class tomorrow and I can't work on it.
Thank you for any help, suggestions, or support.

That's good to know, thank you very much. I was wanting to use it on my G5 this Summer (same one I installed it in before).
I'm entering the fields exactly as I had originally entered them, and I'm using the right letter/number (O/0 or I/1) when applicable. But it still won't let me continue.
I even trashed the 'Final Cut Studio System ID' on my PowerBook, then opened Final Cut, it asked me for the serial number - I entered it, exactly as I had been trying with the disk, and it worked. But it still won't work on the installation disk.
Also, I did a bit of editing on the PowerBook (5.1.4) and then moved to my school's computers (5.1.2) expecting them not to be able to open the file, but it did. I know that 5.1 and 5.1.1 weren't compatable with 5.1.2, so how is 5.1.2 compatable with 5.1.4? Regardless, this is good news.

NEED HELP Deciding. new final cut and a powerpc4

I have a power mac G4 and I want to know will the new final cut package work on it? My pc has a radeon 9000 pro, dual 1.25 processors,, memory 1.25.
i just want to know if final cut and the other programs will work on it. I do not do HD and when i do i will buy another but for Sd is this ok to run and buy the new fc.
thanks everyone who can help

I'd think you will be able to run FCS 2. Your computer is above all of the minimum specs, only wild card here is your graphics card. It has enough VRAM ... just not listed in the compatible cards. Bet it works OK though. Look at the Motion and Color minimums. FCP will work without a hitch in any event, and so should compressor, LiveType, and DVD SP. You could upgrade it if you find it lacking but I'd give it a go with the card you have to see if you're OK first.
http://www.apple.com/finalcutstudio/specs.html
Jerry

Final Cut and Reinstall

Hi,
3 hour project that I've been working on for months.
Experienced system very slow and crashing a lot. so I listened to Apple and cleaned up HD. In the process I deleted about 4 apps that I didn't think had anything to do with FCP. Since I've done that and ran a defrag of the HD FCP won't open any of my projects. I get "This project is unreadable or may be too new for this version of Final Cut" or "Wasn't able to open project" My whole system is running slow - get turning circle on everyting.
I'm thinking I need to uninstall my whole system as in the aps I deleted - garage band and I forgot the others - small programs that I think FC must have used relative to the path of my files in FC. What are your thoughts? If I uninstall I take it there are precautions so as not to lose projects. I have FCP the version before the last version, have a Mac OSx 10.6.8, 2.16 GHz INtel Core 2 Duo, 2 GB 667 MHz DDR2 SDRAm. My project files are on external HDs. What do you think?
Thanks,
joe

Wed, July 4, 2012 3:00:32 PM
Re: [Final Cut Studio] - Re: Final Cut and Reinstall [8rnjp2-2ywwj-b7h77]
From:
Joseph Zabrosky <[email protected]>
To:
discussions-replies <[email protected]>
What version of FCP are you running? fcp7
The Digital Rebellion stuff is great.
I do have Pro Maintenance Tools, which is $140 i think.
http://www.digitalrebellion.com/promaintenance/
that has the 2 apps listed above, plus a project FCP repair tool, corrupt clip finder, etc.
This is your only copy of the project? No, when search project on my external where all my files aree a folder of one of the latest versions comes up with numerous fcp files that were saved at different times and dates. That would be the autosave vault, but it's not in the folder autosave vault.
No backups at all?
Are you sure the autosave lkocation hasnt been changed, and there might be versions somewhere else?
Did you add any new pugins at all? Did you do any software updates before things went south? NO
Without knowing what you deleted then you might need to wipe the system & re-install everything.
if you do this remeber to BU your files & any apps or plugins that are digital files & not on install discs that you have bought, or downloaded.
Cloning the HD as you said in your last email will take care of this?

Final Cut and Pro Tools

I recently installed Final Cut Express on my iMac. I also have Pro Tools 7.4.2 on my machine. When I went to open Final Cut, everything slowed to a screaming halt. One problem was that Final Cut was latching on to my Waves bundle for Pro Tools when it opened. After that, when I restarted my computer it took over five minutes for the desktop to load up. Apple tech support walked me through removing Final Cut, and reinstalling Leopard, but I'm wondering if there's a way for Final Cut and Pro Tools to co-exist. I'm not opening or using them at the same time. 2 BG

The apps should certainly coexist peacefully. If you want to prevent Final Cut from loading your Waves bundle (or any other Audio Units you have installed) then you have to move these units in and out of your /Library/Audio folder. Perhaps worth investigating would be the free AU Manger app for handling these plugs as sets

Final Cut and Motion Roundtripping- FCS2 vs FCS3

I have been getting slow performance and general inefficiency working with Motion files inside of Final Cut with FCS2. I'm working on an Intel based MacBook Pro with 3GB of Ram and Radeon x1600 graphics card. I have been working in HDV1080p30 and only work within one application at a time (I close Motion before going to Final Cut and vice versa).
My question is: Can I expect better performance by upgrading from FCS2 to FCS3 on the same system? I will upgrade immediately if my system can handle the new Final Cut Studio more efficiently.

There are so many possibilities as to why your computer isn't as fast as you want it to be, or as fast as it once was. The amount of data on your drives, overhead of the OS, port malfunction, corrupt preferences, corrupt files on drives (even files you're not using can affect performance, just by being there), age of computer, conflicting 3rd party apps and plug-ins, failing hard drive, failing processor, failing graphics card, failing SMC or PMU, and many many more. There is no way to tell if upgrading to a new version of any software is going to fix your problem. Snow Leopard has less overhead than Leopard, so a new OS might help, but unless you have an Intel Mac, you can't do this.
My guess is, just buying a new set of apps is not the way to go. You need to bench test your machine and find out what, if anything, is misbehaving, and start from there. If it's as simple as not going as fast as you want it to go, but nothing is wrong, then you either need to accept that you're operating at full capacity, or buy a new computer.

Final Cut 5 and HDV-HCR camera

Similar Messages

Maybe you are looking for