Find your carrier when there is no "Carrier" option in settings

Okay, so today my friend had my iPhone and when I got it back off him, there was a "No SIM" message. Apparently, he went onto the Carrier option and switched it to O2 when I am on an unlocked Orange card. The Carrier option has now disappeared and I am stuck looking for the O2 carrier, and my Orange SIM is not picked up. Any way to fix this ?
Cheers for the help

Worked perfectly I'd tried every reset except that seeing as I just presumed it was wifi.
Thanks for the help

Similar Messages

How to find port number , when there will be different instance number ?

In case of portal url,
port number is 50000 for default instance number 00.
how to find port number , when there will be different instance number , instead of 00?
Thanks

Hi
You can find the port number by your instance number as follows:
There is a general format for the port number like you have mentioned.
For 00 instance the port number is 50000.
The general format for the port number goes like this:
5<instance_no>00
If your instance number is 01 then the port number would be 50100.
It depends on the installation type which you perform.
You can also change the instance number during the installation but normally you dont do this.
If you have many components or units installed on your system you may have more than one instance in that case it may go like this 00, 01, 02....accordingly port number will be 50000, 50100, 50200...resp.
Hope this solves your doubt.
If you need some more clarification please lemme know.
Regards
Sumit Jain
**Rewrd with points if useful.

How do I find offending photo when there is a problem uploading photos to order prints?

How do I find offending photo when there is a problem uploading photos to order prints?

What is the problem? What version of iPhoto? Of the OS? Try safe mode
LN

Is it bad to charge your iPad when there is like 30% left ?

Is it bad to charge your iPad when there is like 30% left ?

Question: What is a "charge cycle"?
Answer: Lithium-ion batteries can be charged a finite number of times, as defined by charge cycle. A charge cycle means using all of the battery's power, but that doesn't necessarily mean a single charge. For instance, you could use to your iPad for a few hours one day, using half its power, and then recharge it fully. If you did the same thing the next day, it would count as one charge cycle, not two, so you may take several days to complete a cycle. Each time you complete a charge cycle, it diminishes battery capacity slightly, but you can put your iPad's battery through many charge cycles before it will only hold 80 percent of its original battery capacity.
Don't worry about it, since the battery will take 1000s of charge cycles.
The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

HT4009 I made a in app purchase on a game and it never took, when I went back and tried it again a window popped up that said I have already purchased this item but has not been downloaded yet? How do I download it when there is not a option to download?

I made a in app purchase on a game and it never took, when I went back and tried it again a window popped up that said I have already purchased this item but has not been downloaded yet? How do I download it when there is not a option to download?

Hi Dave_warr,
I would suggest restarting the iPad and see if the download resumes.
iTunes: How to resume interrupted iTunes Store downloads
Resuming downloads from an iOS device
From the Home screen, tap the iTunes icon.
For iPhone/iPod touch, tap More > Downloads. For iPad, tap Downloads.
Enter your account name and password.
Click the "OK" button.
Click the Resume or Resume All button to start the download.
If you don't see the application to download it, then follow these troubleshooting steps:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If the app does not appear in your list of purchases, then contact the iTunes Store for help:
How to report an issue with your iTunes Store, App Store, Mac App Store, or iBookstore purchase
I hope this information helps ....
Have a great day!
- Judy

How do I turn off Private Browsing in Safari when there is no choice in the Settings app?

How do I turn off Private Browsing in Safari when there is no choice in the Settings app?

To turn on private browsing, tap Safari, then tap in the lower-right corner. Tap Private to turn private browsing on.
Note: If you're using an iPad, tap , then Private.
Tap again > turn off private.
http://support.apple.com/kb/ht1677

I have just rented a film and clicked the menu button instead of pause. When I go back to the film to rent again it says I have already rented this go to settings and check for downloads. But there is no download option in settings?

I have just rented a film and clicked the menu button instead of pause. When I go back to the film to rent again it says I have already rented this go to settings and check for downloads. But there is no download option in settings?

It does... Apple TV has a problem with the assignment to the itunes account after updating. Restore to factory settings or unlog and news login to the itunes store helps to see the rented/downloaded film(s).

HT6378 There is no Pause option in Settings to pause the upload to iCloud Photo Library.

There is no Pause option in Settings to pause the upload to iCloud. How can I pause uploading new photos?
In addition, if you choose to turn off the Photo Library beta, you receive a message that indicates the option will be removed from the iPhone.
CorvusIf you choose to continue to Remove, the app indicated that a number of photos will be removed from the iPhone, although it does state that they will remain in iCloud
But, about this option you can see on Apple site http://support.apple.com/en-us/HT6378 in
(When do photos and videos upload to iCloud Photo Library?
When you turn on iCloud Photo Library on your devices, your photos and videos will begin to upload after you connect to the Internet using Wi-Fi. You can see the status on the Photos tab and pause upload for one day from Settings > iCloud > Photos.
Depending on your Internet connection speed, the time it takes for your photos and videos to appear on all of your devices might vary.)
Anyone have this issue too?

The Delete button is only available in your Photo Streams, Camera Roll or Albums you made on the iPhone. Synced photos from a computer can not be deleted and have to be done through the iTunes sync process.
Tap Photo Stream - My Photo Stream then tap on the Edit button here, there should be a Delete button at the bottom. If not try Resetting your iPhone:
From the Home screen double tap the Home button to view the multitasking bar at the bottom. Tap and hold an app at the bottom till the icons wiggle with the minus button visible. Tap the button to close all apps then tap the Home button to get back to the Home page. Press and hold the Sleep button till you see the Slide to power off message and power it off. Once powered down completely press and hold the sleep button till the Apple icon appears.

My ipad is not showing the apn settings when i selected cellular data option on settings? y?

my ipad is not showing the apn settings when i selected cellular data option on settings? y?

pvonk, you were right, something was amiss. It is just a shared calendar (me and my PA) and nothing I could do would seemingly connect the iCal and cloud accounts.
Late last night I upgraded from OSX 10.7.4 to 10.7.5, as I thought that might resolve some settings or minor corruptions in the way my Mac Book was working.
This morning I opened iCal, and once again it attempted to refresh the page. And a few seconds later my iCloud diary appeared on iCal.
The moral of this issue is I think as follows.... when you check all the settings and follow all the advice, and something like this is still not working then it could be the software is slightly corrupt, so a re-install or applying an update (if there is one available) will help resolve issues.
So spot on advice, something was amiss and is now resolved thanks

Finder locks up when there is network traffic

Mac Mini Intel Core Dual 2007
OSX 10.4.8
Recently i had an issue where a Mac Mini 2007 (first Intel Mini) which worked perfectly for years didn't boot anymore.
I checked ran a check of the harddisk using Disk Utility and it turned out that both boot records, the main partition and the Recovery partition were corrupt.
I was able to boot from an external disk and save my data, so i was lucky.
I replaced the harddrive and tried to install OSX from the DVD only to find out that after appx 1 minute into the install the Finder would stop working. Spinning beachball.
Maybe this drive was also bad, so i replaced the drive again with yet another harddisk. Same situation.
So maybe something happened to the memory, maybe when a certain spot on the memory gets used the Finder stops. So i replaced the memory as well. Same situation.
What else can i swap out? Video is on board, so i decided to remove the Wifi card, just as a test. Then the installer runs correctly and the Mini works as expected. I was able to reinstall OSX and since i don't use Wifi, and assuming the Wifi adapter was at fault, i left the Wifi card out and reinstalled OSX.
That was in my lab. But when i moved the Mini to its place and hooked up the ethernet cable again i got the same symptom. After appx.1 minute Finder stops.
When i boot the Mini without the ethernet cable it boots ok. When i connect the ethernet cable i get the same symptom as when i had the Wifi adapter in the Mini, after 1 minute Finder stops.
The ethernet adapter is working because when i configure an IP address that is already on the network i get an error message. This can only happen if the adapter is able to listen on the cable.
I reset the PRAM, tried Safe boot all with the same result.
Any idea what might have happened here?
Thanks,
Ton.

system.log
Jun 6 17:54:44 localhost DirectoryService[11]: Improper shutdown detected
Jun 6 17:54:40 localhost com.apple.launchd[1]: *** launchd[1] has started up. ***
Jun 6 17:54:54 localhost mDNSResponder[17]: mDNSResponder mDNSResponder-212.1 (Jul 24 2009 22:34:14) starting
Jun 6 17:54:54 localhost configd[15]: BUG in libdispatch: 10A432 - 1656 - 0xa30f
Jun 6 17:54:54 Toontjes-Mac-mini configd[15]: setting hostname to "Toontjes-Mac-mini.local"
Jun 6 17:54:54 Toontjes-Mac-mini configd[15]: network configuration changed.
Jun 6 17:54:55 Toontjes-Mac-mini configd[15]: Sleep - Filtered Sleep Failure Report - Power Button Shutdown - Early Failure
Jun 6 17:54:57 Toontjes-Mac-mini bootlog[43]: BOOT_TIME: 1402070074 0
Jun 6 17:54:57 Toontjes-Mac-mini fseventsd[37]: event logs in /.fseventsd out of sync with volume. destroying old logs. (705 23 58876)
Jun 6 17:54:57 Toontjes-Mac-mini fseventsd[37]: log dir: /.fseventsd getting new uuid: 1F2A324C-CFF3-4B36-9120-FC3BBB6AEB7E
Jun 6 17:54:57 Toontjes-Mac-mini com.apple.usbmuxd[27]: usbmuxd-167.1 built for iTunesEightTwo on Jul 9 2009 at 14:02:00, running 32 bit
Jun 6 17:54:57 Toontjes-Mac-mini blued[44]: Apple Bluetooth daemon started
Jun 6 17:54:57 Toontjes-Mac-mini /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[33]: Login Window Application Started
Jun 6 17:54:58 Toontjes-Mac-mini loginwindow[33]: Login Window Started Security Agent
Jun 6 17:54:59 Toontjes-Mac-mini loginwindow[33]: Login Window - Returned from Security Agent
Jun 6 17:54:59 Toontjes-Mac-mini loginwindow[33]: USER_PROCESS: 33 console
Jun 6 17:54:59 Toontjes-Mac-mini com.apple.launchd.peruser.501[72] (com.apple.ReportCrash): Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
Jun 6 17:55:01 Toontjes-Mac-mini com.apple.launchd.peruser.501[72] (com.apple.Kerberos.renew.plist[97]): Exited with exit code: 1
Jun 6 17:55:04 Toontjes-Mac-mini WindowServer[54]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Jun 6 17:55:04 Toontjes-Mac-mini com.apple.WindowServer[54]: Fri Jun 6 17:55:04 Toontjes-Mac-mini.local WindowServer[54] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Jun 6 17:55:27 Toontjes-Mac-mini _mdnsresponder[110]: /usr/libexec/ntpd-wrapper: scutil key State:/Network/Global/DNS not present after 30 seconds
Jun 6 17:55:27 Toontjes-Mac-mini _mdnsresponder[113]: sntp options: a=2 v=1 e=0.100 E=5.000 P=2147483647.000
Jun 6 17:55:27 Toontjes-Mac-mini _mdnsresponder[113]: d=15 c=5 x=0 op=1 l=/var/run/sntp.pid f= time.euro.apple.com
Jun 6 17:55:27 Toontjes-Mac-mini _mdnsresponder[113]: sntp: getaddrinfo(hostname, ntp) failed with nodename nor servname provided, or not known
Jun 6 17:55:40 Toontjes-Mac-mini fseventsd[37]: could not open <</Volumes/Untitled 1/.fseventsd/fseventsd-uuid>> (No such file or directory)
Jun 6 17:55:43 Toontjes-Mac-mini fseventsd[37]: log dir: /Volumes/Untitled 1/.fseventsd getting new uuid: E88E6A82-E349-43AE-B890-4A1FBB044006
Jun 6 17:55:43 Toontjes-Mac-mini mds[32]: (Normal) DiskStore: Creating index for /Volumes/Untitled 1
Jun 6 17:55:47 Toontjes-Mac-mini mdworker[125]: (Error) SyncInfo: searchfs error (Result too large) -- falling back to fsw search /
Jun 6 17:56:36 Toontjes-Mac-mini configd[15]: network configuration changed.
Jun 6 18:00:20 localhost com.apple.launchd[1]: *** launchd[1] has started up. ***
Jun 6 18:00:26 localhost DirectoryService[11]: Improper shutdown detected
Jun 6 18:00:35 localhost mDNSResponder[17]: mDNSResponder mDNSResponder-212.1 (Jul 24 2009 22:34:14) starting
Jun 6 18:00:36 localhost configd[14]: network configuration changed.
Jun 6 18:00:36 Toontjes-Mac-mini configd[14]: setting hostname to "Toontjes-Mac-mini.local"
Jun 6 18:00:37 Toontjes-Mac-mini configd[14]: Sleep - Filtered Sleep Failure Report - Power Button Shutdown - Early Failure
Jun 6 18:00:38 Toontjes-Mac-mini bootlog[46]: BOOT_TIME: 1402070413 0
Jun 6 18:00:38 Toontjes-Mac-mini fseventsd[40]: event logs in /.fseventsd out of sync with volume. destroying old logs. (257 25 341)
Jun 6 18:00:38 Toontjes-Mac-mini fseventsd[40]: log dir: /.fseventsd getting new uuid: BA7A6CFF-FB56-4314-9D28-CE142454FF73
Jun 6 18:00:39 Toontjes-Mac-mini com.apple.usbmuxd[30]: usbmuxd-167.1 built for iTunesEightTwo on Jul 9 2009 at 14:02:00, running 32 bit
Jun 6 18:00:39 Toontjes-Mac-mini blued[47]: Apple Bluetooth daemon started
Jun 6 18:00:39 Toontjes-Mac-mini /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[36]: Login Window Application Started
Jun 6 18:00:40 Toontjes-Mac-mini loginwindow[36]: Login Window Started Security Agent
Jun 6 18:00:41 Toontjes-Mac-mini loginwindow[36]: Login Window - Returned from Security Agent
Jun 6 18:00:41 Toontjes-Mac-mini loginwindow[36]: USER_PROCESS: 36 console
Jun 6 18:00:41 Toontjes-Mac-mini com.apple.launchd.peruser.501[74] (com.apple.ReportCrash): Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
Jun 6 18:00:42 Toontjes-Mac-mini com.apple.launchd.peruser.501[74] (com.apple.Kerberos.renew.plist[103]): Exited with exit code: 1
Jun 6 18:00:50 Toontjes-Mac-mini WindowServer[57]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Jun 6 18:00:50 Toontjes-Mac-mini com.apple.WindowServer[57]: Fri Jun 6 18:00:50 Toontjes-Mac-mini.local WindowServer[57] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
Jun 6 18:01:09 Toontjes-Mac-mini _mdnsresponder[115]: /usr/libexec/ntpd-wrapper: scutil key State:/Network/Global/DNS not present after 30 seconds
Jun 6 18:01:09 Toontjes-Mac-mini _mdnsresponder[118]: sntp options: a=2 v=1 e=0.100 E=5.000 P=2147483647.000
Jun 6 18:01:09 Toontjes-Mac-mini _mdnsresponder[118]: d=15 c=5 x=0 op=1 l=/var/run/sntp.pid f= time.euro.apple.com
Jun 6 18:01:09 Toontjes-Mac-mini _mdnsresponder[118]: sntp: getaddrinfo(hostname, ntp) failed with nodename nor servname provided, or not known
Jun 6 18:02:10 Toontjes-Mac-mini SecurityAgent[129]: com.apple.desktopservices|2014-06-06 18:02:10 +0200
Jun 6 18:04:59 Toontjes-Mac-mini SecurityAgent[129]: com.apple.desktopservices|2014-06-06 18:04:59 +0200

How can I reduce a photo form 1856x1152 pixels to 720x480 pixels when there is no pixel option?

I just purchased PhotoShop12 and am trying to reduce a photo that is 1856 x1152 pixels to a photo that would be 720x480 pixels, but the only options offered on the drop-down image size menu are:
percent, inches, cm, mm, points, picas and columns. There is no pixel option. How do I get a pixel option?

Also note that if you check 'Resample Image' you can then specify pixels in the top part of the resize window but, as hatstead says, this is only sensible if you are maintaining an aspect ratio or if the image is abstract and you don't mind distortion.
Cheers,
Neale
Insanity is hereditary, you get it from your children
If this post or another user's post resolves the original issue, please mark the posts as correct and/or helpful accordingly. This helps other users with similar trouble get answers to their questions quicker. Thanks.

Unable to find Key Events when there are multiple Commands

Hi,
I've developed a simple J2ME Appln containing 3 commands
for ex- Exit,Help and Info(all with same priority).
As there are 3 commands, Exit command is present at the left and the other two namely Help and Info have been listed under Menu and this Menu command is presented at the right.
My MIDlet class has extened MIDlet and implemented CommandListener. Using CommandAction(), I'm able to generate action for Command press and i've also created a nested class which extends Canvas so, using keyPressed and keyReleased, I'm able to find the Key Press Events.
Now, my appln needs to find just the key press events. After i press the Menu command, the two commands namely Help and Info are listed. In tht screen, I need to find out whether any other key events are being generated but my keyPressed and keyReleased are not being called.
Please provide me solution ASAP.

I'm going to make a few assumptions:
1. The menu you're describing is the automatically generated one caused by having more than two commands.
2. The subclass of Canvas is the currently active Displayable (otherwise you won't get any key events at all).
If this is the case (and someone correct me if I'm wrong), key events are being handled by the phone's subsystem to drive the menu, which means there's no way to get them. The way I've approached this kind of problem is to create my own menu painting and handling code and incorporated it into the Canvas. Then, make one Command called 'Menu' and have it invoke your custom menu code.
I realise this isn't an ideal solution, but it's something.

Can you find your iPod when it's not connected to wifi?

The last time I saw my iPod was when I was at my friend's house. There was no wifi connected to it, and I've tried the Find my iPhone app. It didn't work. Is there any other way to track it?

not without it being turned on, in wifi and having the Find MyiPOD turned on.
So, basically, no.

[Desktop][Music] Artist page needs to make it easier to find an album when there are many

If you visit an artist page with a tonne of albums like Antonín Dvořák it is difficult to find a particular album you're looking for. You have the choice between scrolling through heaps of track listings or using grid view. The former is too much to scroll through; the latter requires unnecessary cognitive effort. (I'm going to post a separate idea about that.) What I would like to see is a condensed list of rows, one album per row. Perhaps you could click on part of a row to expand it and see the tracks on it. This could be another display mode alongside the existing two modes.

Yes, you can do it using a script. This code should do the trick:
this.movePage(this.numPages-1, -1);

How to find your iPod when not connected to internet?

I just receving lost my iPod touch. I tried Find my iPod touch on icloud and it needed the iPod to be connected to the internet to locate it. Please help?

You can't locate an iPod Touch without internet connection because it cannot connect to a cellular network unlike the iPhone. It is impossible I guess.

Find your carrier when there is no "Carrier" option in settings

Similar Messages

Maybe you are looking for