FIOS Router Replacement - Is it leased (no charge for replacement)?

Hi all,
All's working good, no problems but I was curious about the procedure for replacing a defective Router Unit.  I have the Westell Model A90-9100M15-10 (91OOEM) model Coax/Ethernet Router unit.
Is there an additional fee for obtaining a replacement?  Are these Routers leased, ie, cost included in my monthly Verizon FIOS bill?
If I needed to order a replacement Router, is the shipping turnaround time usually 1 day?
Can these Routers be obtained at a local Verizon outlet store?  I'm located near one of those stores.
Solved!
Go to Solution.

The router is not leased.  There is no monthly charge for it.
Over the years, VZ's policy regard the router has changed several times, so it depends on when you got the router.
1)  Originally VZ gave away the router.
2)  Then VZ stated charging for the router, but issuing a credit for the amount of the charge resulting in a net cost of $0.
3)  Now VZ says they own the router.
In any case, VZ will replace a faulty router at no charge.  They may or may not want the old router back depending on it's age.
Shipping turnaround on a replacement router is very fast.  Whether you get it in one day depends on when you order it.
Yes, you should be able to obtain a replacement router at a VZ store.

Similar Messages

  • Post the lease rental charges for oprating lease asset using  bdc  for f-02

    hi any can send me the programed for t code f-02
    for post the lease rental charges for operating lease asset using  bdc  for f-02
    This is not a place where you can get your entire work done by others. Please put some effort from your side before turning to the forums for help. Thread locked.
    Locked by: kishan P on Aug 24, 2010 5:47 PM

    hi any can send me the programed for t code f-02
    for post the lease rental charges for operating lease asset using  bdc  for f-02
    This is not a place where you can get your entire work done by others. Please put some effort from your side before turning to the forums for help. Thread locked.
    Locked by: kishan P on Aug 24, 2010 5:47 PM

  • HT3302 How much will be charged for replacing a cracked screen for iPhone 5? How long it will take for repair?

    Hi Folks,
    I am a visitor and had my iPhone 5 cracked the front screen today, I just want to know how long it will take for repair if I send to Apple USA, and the charge for the replacement of the cracked screen.
    Thanks for your advice in advance, I am currently in LA and will put into LA Apple Store asap.

    Warranty and support are only valid in the country of origin.
    If the device was not purchased in the US, an Apple store in the US will not touch it.

  • What does Apple charge for replacement batteries?

    I just upgraded my 2 year old iphone 4s  to a 5s
    but when I had the iphone 4s, I started to notice once it got to the 2 year mark,
    it wasn't holding a charge as long as it used to.  I mean the battery still worked,
    but if I hadn't have upgraded to the 5s,  I would have had a dead battery within
    a couple months..
    I didn't notice that myself until after I got this one. So far its held a charge for an
    entire day and my 4s wasn't even coming close to holding a charge for an entire day,
    but at the time I just thought it had something to do with IOS 7 on the 4s.
    So this leads me to my question. 
    If you purchase an iphone, and something happens to the battery,
    or doesn't hold a charge as long er something like that,
    how much does Apple charge to replace it?
    The 4s I got from the apple store online,  but because I did a trade up this time,
    I ended up getting it from Best Buy  because most of the other stores were out
    of the 16 gig model.
    I know best buy does 'em too but how much do they charge for battery replacements normally?
    I imagine its not the full price of the phone is it?

    oh ok well thats not too bad.  Good to know

  • My grandson has a iPod touch 4th and has broken the screen, does any body know how much apple charge for replacement and can you wait for it to be done or does it get sent away.

    My grandson has broken his screen on his iPod 4th touch. Does anybody know how much apple charge to replace and do they do it while you wait

    Apple will exchange your iPod for a refurbished one for $199 for  64 GB 4G and $99 for the other 4Gs unless you have AppleCare+ extended warranty. Then it would be $29. They do not fix yours.
    Apple - iPod Repair price                       
    A third-party place like the following maybe less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens         
    Replace the screen yourself if you are up to it
      iPod Touch Repair – iFixit          

  • Does anyone know how much apple charges for replacement screens?

    Or if they even replace them?
    If they only replace the whole phone - how much is an iphone 5 refurbished?
    My screen's glass smashed, not badly, and didn't at all affect the touch screen its just getting really annoying looking at such an expensive piece of equpitment with broken glass on it.
    Thanks.

    And those unofficial shops will void your warranty. Even if it were a tad more expensive to go the Apple route (which isn't , in this case), I would not recommend going with unauthorized repair. Besides the warranty issue, they do not usually use genuine parts and the rpair itself might cause other problems in the future....

  • Automatically post the lease rental charges for oprating lease asset using

    hi
    i tried that way which you have given but the wht tac and tax code i am not getting
    anyone can send  the coding accordingly
    the requirement is like that
    Company code (BUKRS)  - Mandatory 
                 Asset class (ANLKL)  - Mandatory -
                 Vendor (Leasing company) (LEAFI) - Mandatory
                 Business Place (BUPLA)
                 WHT Tax code (QSSKZ)
                 Tax code  (MWSKZ)
                 Document type (BLART) - Mandatory
                 Document Date (BLDAT) ) - Mandatory
                 Posting Date (BUDAT) - ) - Mandatory
                 Reference (XBLNR) - ) - Mandatory
                 Document Header text (BKTXT) - ) - Mandatory
    Logic: 
    Pass the values in ANLA for .
    Company code-BUKRS
    Asset Class-ANLKL
    Vendor (Leasing company)-LEAFI
    Get ANLA-ANLN1 and Lease payment (ANLA-LEGEB) from ANLA table
    where Leasing Type ANLA-LEART=02(Operating Lease) . Check Deactivation date ANLA-DEAKT=space OR Posting date in selection BUDAT<= ANLA-LKDAT
        After getting all Assets related to selection vendor post the lease rental document by calling F-02 transaction code (Check BAPI available)
    The program should post the lease payment amount by crediting vendor with sum of lease payment for all assets selected for this vendor and debiting the individual lease payments to u2026u2026. 
    Checks at the time of posting:
    1. Pass the Business place value in to Section code also
    2. Ensure except WHT code entered in selection screen, all the other WHT codes are deleted at the time of posting.
    3. At the time of posting document in the lease rental for Asset line item text it should fill with u201CLease rent for Asset numberu2026u2026u2026for the month of u2026.u201D
    Edited by: jnanaranjan.paikray on Jul 30, 2010 9:26 AM

    hi raj
    i got it
    thk for everything

  • How much does apple charge for replacing back glass for iPhone 4?

    please answer to my question. thanks

    I've been reading $29 from other posters. Visit your Apple Store and find out.

  • How much apple store charge for repair iphone5 screen in uk ?

    Any idea how much Apple will charge for replacing a shattered iphone 5 front screen?  I've had it less than a month and I don't have insurance.
    or - is it possible to give Apple my phone in return for a discount on a new one - with apple refurbing my phone then selling it on?
    Thanks

    Apple do not repair but will replace with an equivalent model.  UK cost is £186.44.

  • How can i use a second router to replace verizon fios router?

    Okay so just as the title says how do i use a second router? I got a cisco valet router... I don't know how to use it because the verizon router/modem is wierd i know how to use a router if i only had a modem but fios gives router/modem so how can i use my 2nd router? The current verizon fios router/modem is b/g mode and i wanna change to b/g/n so i can get a better speed from my internet... SO how can i use my 2nd router? I tried this http://www.dslreports.com/faq/verizonfios/3.0_Networking#12506 but i don't get it can someone guide me better or make a video explaination on how to use a 2nd router? I have it connected with see as in pic i connect from my router Internet port to wan port and the ethernet lan port to the ethernet lan port on verizon fios and no work please help...

    OK, so with this, we have a few options. You appear to have a MoCa connection to the ONT, hence the coaxial cable being present.
    1: The ActionTec can be bridged to the Valet router. This will not require any additional cabling, however it will require a small amount of work to have working. You will also require the ActionTec still in the mix, even though it will not be acting as a router anymore with this configuration.
    Visit http://www.dslreports.com/faq/16077 and look at Option 4. There is a thread linked that will allow you to set up the ActionTec as just a MoCa bridge, and will pass the Public IP to your router. You will, in order for this to work once the ActionTec is bridged, need to connect the cable from your Valet router's Internet port, to the ActionTec's LAN port and nothing else goes to the ActionTec. From this point, your Valet should run as your primary and everything should connect through your Valet. If you are adding another router, a Netgear N300, you should perform the LAN to LAN setup, which we will talk about once you've got the Valet working correctly. LAN to LAN configs require a custom setup, so do not set up the Netgear for now.
    2: This is my preferred method, which would be to run an Ethernet cable to the ONT. Option 6 in the FAQ. This will require spaking to Verizon to have them move your ONT to Ethernet, but once they do this, you can disconnect the Coaxial Cable from your ActionTec router, and plug in your CAT5/CAT6 cable from the ONT to the ActionTec's Internet/WAN port. Use the ActionTec to ensure everything is working after the switchover, and once off the phone, log into the ActionTec, perform a DHCP Release, and then prompty power off the ActionTec. Once this is done, plug the CAT6 cable into your Valet router's Internet port. You should from this point, be able to connect to the Cisco, and if the DHCP Lease was broken successfully, the Cisco should begin serving up your Internet connection. If it does not, leave the Cisco powered off for a few hours to break the DHCP lease, and then power it up. If the Valet does not work, still, give the Valet a factory reset and set up this router again, with the Ethernet cable from the ONT connected to it.
    I would just take a good luck at the FAQ linked above again, and see what would work the best. Easiest thing to do is to get the ONT moved to Ethernet, which allows you to eliminate the ActionTec unless you need it in the future for TV service, and also allows you to use any router with ease.
    Once the Valet is up and running and holds your Public IP address from Verizon (use http://whatismyip.com/ to determine this) , and also serves up IPs to devices on your network, post back and we can help you set up the Netgear. If you have any issues while setting this up, fall back to the ActionTec. It's factory reset will work without configuration needed, regardless of you being on Coax or Ethernet.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

  • Any special way to set up a new Actiontec Wireless N Fios router?

    I'm looking to buy the newer Wireless N router as I'm using an old Westell 9100 wireless g router. Since I'm buying the fios router new outside of Verizon, when I get it is there anything special I have to do to swap out the routers and get the new one working? I assume I have to sign into it and do something. What do I have to do?
    Any help I can get before I get the router so I am prepared ahead of time is appreciated.

    Since you say you're buying it outside of Verizon, I would suggest two things.
    1)  Release the DHCP on the old router before you disconnect it, otherwise you may not be able to get a new DHCP lease right away.  http://www.dslreports.com/faq/15898
    2)  Do a hard reset on the new router to make sure the router is set back to factory defaults.

  • FIOS router causing static and popping noises on computer audio

    Hi, I'm a less than two week old FIOS internet user and am loving the speed and service but I have one problem. The FIOS router seems to be causing static popping noises my desktop computers audio that is connected to the FIOS router by the yellow Ethernet cable. Theses noises don't occur on any of the laptops connected to the router by the wireless or when I connect a laptop to the router via a Ethernet cable.
    Ways I found to eliminate the noises temporary:
    Restarting the desktop computer or shutting down then turning on the desktop computer.
    Ways I found to eliminate the noises permanently
    Turning off and unplugging the router.
    Hooking up the FIOS router via the Ethernet cable to a laptop. I unfortunately do not have a wireless built into my desktop.
    What I've tried and failed
    First I thought it was the Ethernet cable, so I replaced it. The noises did not go away.
    I thought it might be the headset I use which are connected to the computer by a usb port. Unplugging the headset and using earphones which are connect to the computer by the audio slot did not eliminate the noises.
    Then I contacted Verizon, and they thought it might be a faulty router, so they sent me a new one. The noises unfortunately did not go away.
    I then thought the noises might be occurring because the router was close to the computer. So I moved the router as far away as possible from the computer (its connect to the router by a Ethernet cable so it wasn't that far) but the noises didn't go away.
    Notes & Points
    The noises do not start the moment I turn on the router and computer, but a hour or two after.
    I think I've narrowed the problem down to occurring only when the desktop computer is connected to the router by the Ethernet cable. Though replacing the Ethernet cable has not resolved the issue.
    I also have found that location of the FIOS router also doesn't matter since the noises did not return even though the router was right up against the computer when I connected the FIOS router to my laptop.
    I have Windows 7 Home Premium 64, 3.5 gigs of ram, and a dual 2.0 GHz processor.
    So that sums up my problem. If you guys have any tips or ideas of how to fix my issue, it would be greatly appreciated.

    Sounds like a shielding problem on the AUDIO cables or a grounding issue.   PC sound systems are notorious for having lousy audio cables feeding (I regularly pickup the local FM station on my speakers).
    Try replacing the audio cables with better quality shield cables and see if that helps.
    Are the router, speakers, and PC all plugged into the same outlet?  Are they all polarized plugs?  If note, try flipping the power plug on the non-polarized connections.
    The sound could be coming from interference INSIDE the PC itself ... the proximity of sound cables inside and the audio chipset to the ethernet chipset.   You didn't indicate if the audio/ethernet are on the motherboard or seperate cards.   If they are seperate cards, try relocating the cards furfher from one another inside the chassis and also look at the audio cable (particularly the analog cable that runs from the CD to the audio card to make sure it's not routed past or near the ethernet electronics.
    How far distant is the router from the PC?  If you pull the ethernet cable from the router (not turn if off, unplug the ethernet cable running to the PC), does it stop?

  • How much does Apple charge to replace a cracked screen?

    I bought my unlocked iPhone 3gs with a slightly cracked screen, and now I am looking around to see how much it would cost to replace the screen. More specifically, I am wondering how much Apple charges to replace a cracked screen.

    Genius at Apple Store replaces the entire front assembly of iPhone 3GS which includes the Front Screen, LCD, Home Button, Midframe for $99. All Apple Stores (6) in my area do this. If you want to go the Out of Warranty route with complete Replacement iPhone 3GS exactly like yours it would be $149 at Apple Store.

  • 2nd Gen iPod Touch Reboots Westell 9100EM Verizon FiOS Router

    I've been round and round with Verizon FiOS with no answers yet.
    My iPod Touch 2nd Gen 16GB 3.0 will connect successfully to my FiOS router wirelessly...but as soon as I try to access my mail or any internet site my router reboots. I just got FiOS a week or so ago. They have replaced the router but I still have the same issue. I never had this problem with my cable provider that I had in the past and using my Linksys WRT54G router. As a test, I connected my Linksys to my FiOS router as an access point and turned the wireless off on my FiOS router. As soon as attempted to get my mail on the iPod...the FiOS router rebooted again...but not the Linksys. I have tried using WPA w/TKIP (which I used on my Linksys) as well as WEP (although I don't like WEP).
    I'm a Systems Engineer by trade and do this kind of troubleshooting for a living but this has me stumped. Anyone else experience this or have any ideas?

    Wow, I never have heard of a device causing a router to reboot. I've got one idea about what could be happening but it is too strange to be the cause. Try updating the router DNS addresses to something that works - like OpenDNS.
    Also, I would ask Verizon for another router. Other people certainly don't have this problem.

  • Time Capsule Bandwidth Speed versus Fios Router Directly

    Verizon just replaced my Fios Router because download speeds were 5 megs/sec. I just received my new one in the mail and hooked it up. I connected to the FIOS router and was getting 27 mbps download and 5 on the upload. I went back to my original setup of turning off the Radio broadcast on the FIOS router and using my time capsule to broadcast wifi....i have dropped to 5 mbps download speed--same speeds when Verizon thought it was their problem. What do I do? I don't understand the limitations or what has happened. Can someone provide suggestions?

    Bridge means to remove all routing from the TC.
    Open Manual setup in airport utility (on lion v5.6 utility only).
    Go to internet tab.
    Go to Connection sharing.
    Select off, bridge mode.. update the TC.. it is now bridge.
    If still slow there are a number if issues.. and I doubt we have found the ultimate cause.. bad firmware in 7.6 could be one of them .. go back to 7.5.2
    ie in airport utility go to the firmware update but hold down the option key and you can select older firmware.. they work better than new ones.
    You also might need to reset the TC to factory to get rid of the poor settings.

Maybe you are looking for