Firefox 3.5 will not mount on Mac OS 10.3

I mistakenly delted and trashed Firefox. When attempting to install Firefox 3.5 on Mac OS 10.3, mounting fails.
== Operating system ==
Mac OS 103

Firefox 2.0.0.20 is the last version for OSX 10.3.9 and earlier. Firefox version 3.0 and later require OSX 10.4 and newer.
http://www.mozilla.com/firefox/system-requirements-v3.html
http://www.mozilla.com/firefox/system-requirements.html
Download Firefox 2.0.0.20 for OSX here (choose your language and download the .dmg file): https://ftp.mozilla.org/pub/mozilla.org/firefox/releases/2.0.0.20/mac/
See: http://support.mozilla.com/en-US/kb/Installing+Firefox+on+Mac

Similar Messages

  • New Hard drive in NTFS--will not mount on Mac

    I have a 3rd Gen ipod with a dead 30g hard drive. I bought a 40g Toshiba that came formatted in NTFS. I installed the new hard drive and tried to run updater, but the ipod will not mount on a Mac Powerbook G4.
    The ipod shows that it is charging and says "Disk Mode," has a check mark on the screen and says "OK to disconnect"
    I have always used a Mac and I do NOT have access to a PC to reformat it there (at least not that I know of).
    How do I force the Mac to see my ipod with the new drive? Oh wise and powerful Mac wizards, help me!
    PS If this is a really simple thing to fix, please be gentle. I still use my IIsi and enjoy playing Civilization 1. The G4 belongs to a roommate.

    To recap:
    I have a 3rd Gen ipod with a dead 30g hard drive. I bought a 40g Toshiba that came formatted in NTFS. I installed the new hard drive and tried to run updater, but the ipod would not mount on a Mac Powerbook G4. I am connecting through firewire.
    The iPod showed that it was charging and said "Disk Mode," had a check mark on the screen and said "OK to disconnect"
    It was stuck here for hours and then it finally managed to mount. (it might have been after a reset, I don't remember).
    I ran iPod updater and RESTOREd the hard drive. It asked for a new name, language, etc. iTunes opened and I recopied some of my music back onto the iPod. I ejected the iPod safely and copied some more music from an external drive onto my main machine.
    When I tried to reconnect the iPod, it went back in to disk mode, check mark, ok to disconnect, etc and there it has been for 26 hours.
    I cannot even get iPod updater to find it.
    What the heck is going on?

  • Firefox 3.6.13 will not mount on my Mac 10.3.9

    I tried downloading Firefox 3.6.13 for the first time on my Mac 10.3.9 and get the message that it will not mount.

    Firefox 3.6.13 requires at least OS X 10.4, the last version of Firefox to work on OS X 10.3.9 was Firefox 2.0.0.20
    ftp://ftp.mozilla.org/pub/mozilla.org/firefox/releases/2.0.0.20/mac/en-US/

  • It will not run on Mac OSX 10.5.8, on a G% dual 2.0ghz, now my older version of Firefox is gone...

    I downloaded Firefox 4.0 and It will not run on Mac OSX 10.5.8, on a Mac G5 dual 2.0ghz. Now my older version of Firefox is gone...Why won't it work, the download page says it is for OSX and does not say it will not work on any particular OSX. Can your clarify. And can I get the old Firefox 3 back or should I continue using Safari....?

    Yes I've read every one of them, none of them provide solutions whatsoever, I have spent about ten hours on this site in the past two days to no avail, none of the "resolved" threads provided any sort of solution for me, I have tried everything suggested on this website so far, multiple times, to no avail.

  • External backup drive will not mount on new mac mini. still works fine on the old one. new one is running mavericks

    I just bought new-to-me mac mini running OSX mavericks.
    Trying to migrate from old mac mini using simpletech external hard drive.
    It still mounts on my old mac mini (system 10.5) but will not mount or show up when I plug it in to the new mac mini running mavericks.
    Any ideas?

    BDAqua wrote:
    What exactly shows in System Profiler>Hardware>USB for those drives?
    Boot from the Install Disc & see if they show up, not grayed out in Disk Utility.
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    We were thinking along the same lines. While at home I dug up a firewire enclosure and put a bootable GUID formatted drive in it (that I had in one of the usb enclosures) and started her computer holding down the option key and then chose to boot from the external firewire. All usb drives are now mounting upon connection. I asume that her drive has bad sectors on it (even though the SMART status says it's OK) and is not loading all the drivers properly for USB to mount. I was suspicious from the beginning that the OS was corrupt when she first had me look at it. It was at that point that I booted it in target mode, connected to my Macbook Pro, and then CCC'd to a usb drive that I had. I then had a couple of difficulties installing the new OS. Should have known......
    I am now going to put a new drive in it for her and she'll be up and running.
    Thanks so much for your help and thoughts that got me thinking as well.
    pax

  • Tried to download version 4, which replaced old 3.6, but I'm getting a message that version 4 will not work with Mac OS 10 (I have OS 10.4.11). How can I download previous Firefox version?

    Tried to download version 4, which replaced old 3.6, but I'm getting a message that version 4 will not work with Mac OS 10 (I have OS 10.4.11). How can I download previous Firefox version?

    You can download firefox 3.6.16 here: http://www.mozilla.com/en-US/firefox/all-older.html

  • I am trying to connect my LaCie thunderbolt 2 5big drives to my new Mac Pro.  They will not mount.  If I unplug them and plug them into my MBP they mount immediately

    I have 2 LaCie Thunderbolt 2 5Big drives.  I have been using them successfully with my mbp.  I just purchased a Mac Pro and plugged them in and they will not mount.  I am stumped as how to get the Mac Pro to recognize them

    This is the Mac Pro black cylinder, late 2013 model?
    Have you tried one at a time? Have you tried different ThunderBolt ports?
    What display are you using and what port is it plugged into? You may want to be sure your drives and your displays are not on the same bus.
    This article show which ports are on which ThunderBolt Busses:
    Mac Pro (Late 2013): Using multiple displays - Apple Support

  • Bought a MacBookair ...I installed firefox...will not play videos on the delta airline employee website(extranetlanding page) it says plug ins need to be installed.....I have firefox on my Mac desktop and the video works fine .

    '''
    ''' Delta airlines employee
    website (extranetlandingpage) Firefox
    works excellent on my Mac 21 inch desktop which i have had since '09...Today, i bought a mac Book air
    , downloaded firefox and it will not allow me to watch video library which i need for training... it says install plug- ins......What did I do wrong? I did not have this problem with my other Mac.......

    Sorry, Flash for Android is not yet compatible with Firefox for Android. We hope to work with Adobe to fix this in a future release.
    You can play some YouTube videos by enabling YouTube's HTML5 beta. Only videos available in the WebM or Theora formats will play in Firefox for Android: http://youtube.com/html5

  • My Ipod 4th Gen will not mount into Itunes

    Please anyone with technical knowledge HELP ME.
    The basic problem is that my 4th Generation Ipod will not mount into Itunes.
    Let me tell you what I have done so far this includes all the R's, I have also followed the advice of reinstalling itunes and Quicktime I have also tried backwards installing to version 6 (at present I have upgraded to version 7.0.2). The ipod is visible in Windows and I still am able to use it as disk as I have programs I am using off it.
    I have tried a fifth gen and also an Ipod mini and both mount onto my Itunes.
    I have tried to reinstall the Ipod software, however the previous ipod updates do not work and as the Ipod cannot be mounted I cannot use Itunes to update it as it is not visible.
    I have also run the Ipod Diagnostic in Itunes and everything seems fine (I have included the report if anyone can please understand it)and at the very bottom it states that the Ipod is truly Mounted. WELL ITS NOT
    I really am getting desperate now as this is the same on both my Desktop and Laptop and I am getting very close to throwing the whole thing out along with all the rest of my computer equipment.
    Thanks a lot
    DIAGNOSTIC REPORT
    Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
    FUJITSU SIEMENS AMILO PRO V2030
    iTunes 7.0.2.16
    iPodService 7.0.2.16 is currently running.
    iTunesHelper 7.0.2.16 is currently running.
    Current user is an administrator.
    Connected Storage Devices:
    IDE\DiskFUJITSUMHV2040BH______________________00000025, Bus Type ATA, Bus Address [0,0]
    USBSTOR\DiskApple__iPod___________1.62, Bus Type USB
    Universal Serial Bus Controllers:
    VIA Rev 5 or later USB Universal Host Controller, PCI bus 0, device 16, function 0. Device is working properly.
    VIA USB Enhanced Host Controller, PCI bus 0, device 16, function 4. Device is working properly.
    IEEE 1394 Host Controllers:
    Texas Instruments OHCI Compliant IEEE 1394 Host Controller, PCI bus 0, device 12, function 2. Device is working properly.
    Connected Device Information
    PAUL'S IPOD (E:\), iPod with Click Wheel running firmware version 3.1.1
    Serial Number: JQ447113PQ7
    Bus Speed: 61440
    The last connected iPod serial number: JQ524ER2S41.
    The iPod Service Logging Information:
    [SERVICE: 0xDA8,09:16:59 INFO] Started C:\Program Files\iPod\bin\iPodService.exe (Sat Nov 18 09:16:59 2006)
    [SERVICE: 0xDA8,09:16:59 INFO] ##### iPodService starting as a service, version: 7.0.2.16
    [SERVICE: 0xDB8,09:17:00 INFO] Got signaled to go ahead... Starting device manager!
    [SERVICE: 0x4F0,09:17:00 INFO] Listener Window created
    [SERVICE: 0xDB8,09:17:02 INFO] [InterfaceArrival] \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0xDB8,09:17:02 INFO] device \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0xDB8,09:17:02 INFO] device is an iPod
    [SERVICE: 0xDB8,09:17:02 INFO] type 0x7 drive 0x1 partition 0x0
    [SERVICE: 0xDB8,09:17:08 INFO] [-1] set waiting to mount = 1
    [SERVICE: 0xDB8,09:17:08 INFO] [1] Assigning session 0
    [SERVICE: 0xDB8,09:17:08 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_objDeviceNameMap
    [SERVICE: 0xDB8,09:17:08 INFO] [1] added state machine 1 to m_objDeviceIdMap
    [SERVICE: 0xDB8,09:17:08 INFO] [1] added device number 1 to m_objDeviceNumberMap
    [SERVICE: 0xDB8,09:17:08 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_vctDeviceInterfaces
    [SERVICE: 0xDB8,09:17:08 INFO] [1] input #0 from src #0
    [SERVICE: 0xD24,09:17:08 INFO] [1] input #0
    [SERVICE: 0xD24,09:17:08 INFO] [MACHINE 1 INPUT #0] - (HDW) Interface Arrival
    [SERVICE: 0xD24,09:17:08 INFO] [1] progress state is 2, Waiting to mount = 1
    [SERVICE: 0xD24,09:17:08 INFO] [1] progress is now 2
    [SERVICE: 0xD24,09:17:08 INFO] [1] progress is now 2
    [SERVICE: 0xD24,09:17:08 INFO] [MACHINE 1 TRANSITION] - {Unknown} ==> {Connected}
    [SERVICE: 0xD24,09:17:08 INFO] [MACHINE 1 ACTIONS] - {Connected}
    [SERVICE: 0xD24,09:17:08 INFO] [1] SCSI Inquiry attempt #0
    [SERVICE: 0xD24,09:17:08 INFO] VendorId: Apple
    [SERVICE: 0xD24,09:17:08 INFO] ProductId: iPod
    [SERVICE: 0xD24,09:17:08 INFO] revision: 1.62
    [SERVICE: 0xD24,09:17:08 INFO] vendor bytes:
    [SERVICE: 0xD24,09:17:08 INFO] 02 01 00 00 00 00 00 00 00 05 00 13 12 00 00 00 00 00 00 00
    [SERVICE: 0xD24,09:17:08 INFO] [1] firmware version: 1.62 (0x13E)
    [SERVICE: 0xD24,09:17:08 INFO] [1] Power State: Not Powered
    [SERVICE: 0xD24,09:17:08 INFO] [1] Checkpoint attempt #0
    [SERVICE: 0xD24,09:17:08 ERROR] Did not find first letter of stage
    [SERVICE: 0xD24,09:17:08 INFO] [1] serial number 000A270002BF5F21
    [SERVICE: 0xD24,09:17:08 INFO] [1] *** CONNECTED - Sending event out, device session 0.
    [SERVICE: 0x4F0,09:17:11 INFO] [SIMULATED VOLUME ARRIVAL] generating volume mount for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0x4F0,09:17:11 INFO] [VolumeArrive] mask = 0x1C
    [SERVICE: 0x4F0,09:17:11 INFO] looking up device # for \\.\E:
    [SERVICE: 0x4F0,09:17:11 INFO] type 0x7 drive 0x1 partition 0x1
    [SERVICE: 0x4F0,09:17:11 INFO] iTunes device #1 found with drive letter E, mask 0x10
    [SERVICE: 0x4F0,09:17:11 INFO] [1] set waiting to mount = 0
    [SERVICE: 0x4F0,09:17:11 INFO] [1] input #1 from src #0
    [SERVICE: 0x52C,09:17:11 INFO] [1] input #1
    [SERVICE: 0x4F0,09:17:11 INFO] looking up device # for \\.\D:
    [SERVICE: 0x4F0,09:17:11 INFO] type 0x2 drive 0x0 partition 0xffffffff
    [SERVICE: 0x4F0,09:17:11 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
    [SERVICE: 0x4F0,09:17:11 INFO] looking up device # for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0x4F0,09:17:11 INFO] type 0x7 drive 0x1 partition 0x0
    [SERVICE: 0xDB8,09:17:11 INFO] [VolumeArrive] mask = 0x1C
    [SERVICE: 0xDB8,09:17:11 INFO] looking up device # for \\.\E:
    [SERVICE: 0xDB8,09:17:11 INFO] type 0x7 drive 0x1 partition 0x1
    [SERVICE: 0xDB8,09:17:11 INFO] iTunes device #1 found with drive letter E, mask 0x10
    [SERVICE: 0xDB8,09:17:11 INFO] [1] set waiting to mount = 0
    [SERVICE: 0xDB8,09:17:11 INFO] [1] input #2 from src #0
    [SERVICE: 0x4EC,09:17:11 INFO] [1] input #2
    [SERVICE: 0xDB8,09:17:11 INFO] looking up device # for \\.\D:
    [SERVICE: 0xDB8,09:17:11 INFO] type 0x2 drive 0x0 partition 0xffffffff
    [SERVICE: 0xDB8,09:17:11 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
    [SERVICE: 0x52C,09:17:11 INFO] [MACHINE 1 INPUT #1] - (HDW) Volume Mount
    [SERVICE: 0x52C,09:17:11 INFO] [MACHINE 1 TRANSITION] - {Connected} ==> {Mounted}
    [SERVICE: 0xDB8,09:17:11 INFO] looking up device # for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0xDB8,09:17:11 INFO] type 0x7 drive 0x1 partition 0x0
    [SERVICE: 0x52C,09:17:11 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x52C,09:17:11 INFO] [MACHINE 1 ACTIONS] - {Mounted}
    [SERVICE: 0x52C,09:17:11 INFO] [1] progress state is 2, Waiting to mount = 0
    [SERVICE: 0x52C,09:17:11 INFO] [1] progress state is 2, Waiting to mount = 0
    [SERVICE: 0x52C,09:17:14 ERROR] Did not find first letter of stage
    [SERVICE: 0x52C,09:17:15 INFO] [1] OS says filesystem is FAT32
    [SERVICE: 0x52C,09:17:16 INFO] [1] ===== iPod Touch Wheel =====
    [SERVICE: 0x52C,09:17:16 INFO] [1] progress state is 2, Waiting to mount = 0
    [SERVICE: 0x52C,09:17:16 INFO] 9:17:16, year 2006, day of yr. 321, GMT offset 0 isDST 0
    [SERVICE: 0x52C,09:17:16 INFO] [1] progress is now 0
    [SERVICE: 0x52C,09:17:18 INFO] [1] *** MOUNTED - Sending event out, device session 0.
    [SERVICE: 0x52C,09:17:18 INFO] [1] Auto-launch iTunes DISABLED
    [SERVICE: 0x4EC,09:17:18 INFO] [MACHINE 1 INPUT #2] - (HDW) Volume Mount
    [SERVICE: 0x4EC,09:17:18 INFO] ** CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:18:21 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:18:21 INFO] [1] input #3 from src #0
    [SERVICE: 0xD24,09:18:21 INFO] [1] input #3
    [SERVICE: 0x4F0,09:18:21 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:18:21 INFO] [1] input #4 from src #0
    [SERVICE: 0x4EC,09:18:21 INFO] [1] input #4
    [SERVICE: 0x4F0,09:18:21 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:18:21 INFO] [1] input #5 from src #0
    [SERVICE: 0x52C,09:18:21 INFO] [1] input #5
    [SERVICE: 0xD24,09:18:22 INFO] [MACHINE 1 INPUT #3] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:18:23 INFO] Connection Detection Status - 0x1806002, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0xD24,09:18:23 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0xD24,09:18:23 INFO] [1] progress is now 1
    [SERVICE: 0x4EC,09:18:23 INFO] [MACHINE 1 INPUT #4] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:18:24 INFO] [MACHINE 1 TRANSITION] - {Mounted} ==> {Unknown}
    [SERVICE: 0x4EC,09:18:24 INFO] Connection Detection Status - 0x1806002, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x4EC,09:18:24 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x52C,09:18:24 INFO] [MACHINE 1 INPUT #5] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:18:24 INFO] [MACHINE 1 ACTIONS] - {Unknown}
    [SERVICE: 0x52C,09:18:24 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x52C,09:18:24 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0xD24,09:18:24 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0xD24,09:18:24 INFO] [1] *** DISCONNECTED - Sending event out, device session 0.
    [SERVICE: 0xD24,09:18:24 INFO] [1] progress is now 0
    [SERVICE: 0xD24,09:18:24 INFO] [1] progress state is 0, Waiting to mount = 0
    [SERVICE: 0x4F0,09:18:38 INFO] [VolumeRemoved] existing mask 0x10, arrive mask 0x10
    [SERVICE: 0x4F0,09:18:38 INFO] [1] value = 1
    [SERVICE: 0x4F0,09:18:38 INFO] [1] input #6 from src #0
    [SERVICE: 0x4EC,09:18:38 INFO] [1] input #6
    [SERVICE: 0x4EC,09:18:38 INFO] [MACHINE 1 INPUT #6] - (HDW) Volume Unmount
    [SERVICE: 0x4EC,09:18:38 INFO] [1] progress is now 3
    [SERVICE: 0x4EC,09:18:38 INFO] [1] Setting progress to 3
    [SERVICE: 0x4EC,09:18:38 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:18:38 INFO] [InterfaceRemoved]
    [SERVICE: 0x4F0,09:18:38 INFO] [1] value = 0
    [SERVICE: 0x4F0,09:18:38 INFO] removed device number 1 from m_objDeviceNumberMap
    [SERVICE: 0x4F0,09:18:38 INFO] [1] input #7 from src #0
    [SERVICE: 0x52C,09:18:38 INFO] [1] input #7
    [SERVICE: 0x4F0,09:18:38 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:18:38 INFO] [1] Progress state is 3, Waiting to disconnect = 0
    [SERVICE: 0x4F0,09:18:38 ERROR] device number 0 exists, but isn't in m_objDeviceNumberMap!
    [SERVICE: 0x4F0,09:18:38 INFO] removed device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" from m_vctDeviceInterfaces
    [SERVICE: 0x4F0,09:18:38 INFO] [1] input #8 from src #0
    [SERVICE: 0xD24,09:18:38 INFO] [1] input #8
    [SERVICE: 0x52C,09:18:38 INFO] [MACHINE 1 INPUT #7] - (HDW) Interface Removal
    [SERVICE: 0x52C,09:18:38 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0xD24,09:18:38 INFO] [MACHINE 1 INPUT #8] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:18:38 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0xD24,09:18:38 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:18:39 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:18:39 INFO] [1] input #9 from src #0
    [SERVICE: 0x4EC,09:18:39 INFO] [1] input #9
    [SERVICE: 0x4EC,09:18:39 INFO] [MACHINE 1 INPUT #9] - (HDW) CheckDevNode
    [SERVICE: 0x4EC,09:18:39 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x4EC,09:18:39 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:18:48 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:18:48 INFO] [1] input #10 from src #0
    [SERVICE: 0x52C,09:18:48 INFO] [1] input #10
    [SERVICE: 0x4F0,09:18:48 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:18:48 INFO] [1] input #11 from src #0
    [SERVICE: 0xD24,09:18:48 INFO] [1] input #11
    [SERVICE: 0x52C,09:18:49 INFO] [MACHINE 1 INPUT #10] - (HDW) CheckDevNode
    [SERVICE: 0x52C,09:18:49 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0xD24,09:18:49 INFO] [MACHINE 1 INPUT #11] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:18:49 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:34:58 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:34:58 INFO] [1] input #12 from src #0
    [SERVICE: 0x4EC,09:34:59 INFO] [1] input #12
    [SERVICE: 0x4EC,09:34:59 INFO] [MACHINE 1 INPUT #12] - (HDW) CheckDevNode
    [SERVICE: 0x4EC,09:35:00 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:39:01 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:39:01 INFO] [1] input #13 from src #0
    [SERVICE: 0x52C,09:39:01 INFO] [1] input #13
    [SERVICE: 0x52C,09:39:02 INFO] [MACHINE 1 INPUT #13] - (HDW) CheckDevNode
    [SERVICE: 0x52C,09:39:02 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:39:02 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:39:02 INFO] [1] input #14 from src #0
    [SERVICE: 0xD24,09:39:02 INFO] [1] input #14
    [SERVICE: 0xD24,09:39:02 INFO] [MACHINE 1 INPUT #14] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:39:02 INFO] * CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:42:41 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:42:41 INFO] [1] input #15 from src #0
    [SERVICE: 0x4F0,09:42:41 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:42:41 INFO] [1] input #16 from src #0
    [SERVICE: 0x4F0,09:42:41 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:42:41 INFO] [1] input #17 from src #0
    [SERVICE: 0x52C,09:42:41 INFO] [1] input #15
    [SERVICE: 0x4EC,09:42:41 INFO] [1] input #16
    [SERVICE: 0xD24,09:42:41 INFO] [1] input #17
    [SERVICE: 0x52C,09:42:41 INFO] [MACHINE 1 INPUT #15] - (HDW) CheckDevNode
    [SERVICE: 0x52C,09:42:49 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x4EC,09:42:49 INFO] [MACHINE 1 INPUT #16] - (HDW) CheckDevNode
    [SERVICE: 0x4EC,09:42:49 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0xD24,09:42:49 INFO] [MACHINE 1 INPUT #17] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:42:49 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x4F0,09:42:51 INFO] [InterfaceArrival] \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0x4F0,09:42:51 INFO] type 0x7 drive 0x1 partition 0x0
    [SERVICE: 0x4F0,09:42:51 INFO] [1] set waiting to mount = 1
    [SERVICE: 0x4F0,09:42:51 INFO] [1] Attempt to reassign from session 0 to session 0, DENIED!
    [SERVICE: 0x4F0,09:42:51 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_objDeviceNameMap
    [SERVICE: 0x4F0,09:42:51 INFO] [1] added state machine 1 to m_objDeviceIdMap
    [SERVICE: 0x4F0,09:42:51 INFO] [1] added device number 1 to m_objDeviceNumberMap
    [SERVICE: 0x4F0,09:42:51 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_vctDeviceInterfaces
    [SERVICE: 0x4F0,09:42:51 INFO] [1] input #18 from src #0
    [SERVICE: 0x52C,09:42:51 INFO] [1] input #18
    [SERVICE: 0x4F0,09:42:51 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:42:51 INFO] [1] input #19 from src #0
    [SERVICE: 0x4EC,09:42:51 INFO] [1] input #19
    [SERVICE: 0x4F0,09:42:51 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:42:51 INFO] [1] input #20 from src #0
    [SERVICE: 0xD24,09:42:51 INFO] [1] input #20
    [SERVICE: 0x52C,09:42:51 INFO] [MACHINE 1 INPUT #18] - (HDW) Interface Arrival
    [SERVICE: 0x52C,09:42:51 INFO] [1] progress state is 2, Waiting to mount = 1
    [SERVICE: 0x52C,09:42:51 INFO] [1] progress is now 2
    [SERVICE: 0x52C,09:42:51 INFO] [1] progress is now 2
    [SERVICE: 0x52C,09:42:51 INFO] [MACHINE 1 TRANSITION] - {Unknown} ==> {Connected}
    [SERVICE: 0x52C,09:42:51 INFO] [MACHINE 1 ACTIONS] - {Connected}
    [SERVICE: 0x52C,09:42:51 INFO] [1] SCSI Inquiry attempt #0
    [SERVICE: 0x52C,09:42:51 INFO] VendorId: Apple
    [SERVICE: 0x52C,09:42:51 INFO] ProductId: iPod
    [SERVICE: 0x52C,09:42:51 INFO] revision: 1.62
    [SERVICE: 0x52C,09:42:51 INFO] vendor bytes:
    [SERVICE: 0x52C,09:42:51 INFO] 02 01 00 00 00 00 00 00 00 05 00 13 12 00 00 00 00 00 00 00
    [SERVICE: 0x52C,09:42:51 INFO] [1] firmware version: 1.62 (0x13E)
    [SERVICE: 0x52C,09:42:51 INFO] [1] Power State: Not Powered
    [SERVICE: 0x52C,09:42:51 INFO] [1] Checkpoint attempt #0
    [SERVICE: 0x52C,09:42:51 ERROR] Did not find first letter of stage
    [SERVICE: 0x52C,09:42:51 INFO] [1] serial number 000A270002BF5F21
    [SERVICE: 0x52C,09:42:51 INFO] [1] *** CONNECTED - Sending event out, device session 0.
    [SERVICE: 0x4EC,09:42:51 INFO] [MACHINE 1 INPUT #19] - (HDW) CheckDevNode
    [SERVICE: 0x4EC,09:42:51 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0xD24,09:42:51 INFO] [MACHINE 1 INPUT #20] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:42:51 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x4F0,09:42:53 INFO] [SIMULATED VOLUME ARRIVAL] generating volume mount for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0x4F0,09:42:53 INFO] [VolumeArrive] mask = 0x1C
    [SERVICE: 0x4F0,09:42:53 INFO] looking up device # for \\.\E:
    [SERVICE: 0x4F0,09:42:53 INFO] type 0x7 drive 0x1 partition 0x1
    [SERVICE: 0x4F0,09:42:53 INFO] iTunes device #1 found with drive letter E, mask 0x10
    [SERVICE: 0x4F0,09:42:53 INFO] [1] set waiting to mount = 0
    [SERVICE: 0x4F0,09:42:53 INFO] [1] input #21 from src #0
    [SERVICE: 0x52C,09:42:53 INFO] [1] input #21
    [SERVICE: 0x4F0,09:42:53 INFO] looking up device # for \\.\D:
    [SERVICE: 0x4F0,09:42:53 INFO] type 0x2 drive 0x0 partition 0xffffffff
    [SERVICE: 0x4F0,09:42:53 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
    [SERVICE: 0x4F0,09:42:53 INFO] looking up device # for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
    [SERVICE: 0x4F0,09:42:53 INFO] type 0x7 drive 0x1 partition 0x0
    [SERVICE: 0x52C,09:42:54 INFO] [MACHINE 1 INPUT #21] - (HDW) Volume Mount
    [SERVICE: 0x52C,09:42:54 INFO] [MACHINE 1 TRANSITION] - {Connected} ==> {Mounted}
    [SERVICE: 0x52C,09:42:54 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0x52C,09:42:54 INFO] [MACHINE 1 ACTIONS] - {Mounted}
    [SERVICE: 0x52C,09:42:54 INFO] [1] progress state is 2, Waiting to mount = 0
    [SERVICE: 0x52C,09:42:54 INFO] [1] progress state is 2, Waiting to mount = 0
    [SERVICE: 0x52C,09:42:54 ERROR] Did not find first letter of stage
    [SERVICE: 0x52C,09:43:02 INFO] [1] OS says filesystem is FAT32
    [SERVICE: 0x52C,09:43:03 INFO] [1] ===== iPod Touch Wheel =====
    [SERVICE: 0x52C,09:43:03 INFO] [1] progress state is 2, Waiting to mount = 0
    [SERVICE: 0x52C,09:43:03 INFO] 9:43:3, year 2006, day of yr. 321, GMT offset 0 isDST 0
    [SERVICE: 0x52C,09:43:03 INFO] [1] progress is now 0
    [SERVICE: 0x52C,09:43:04 INFO] [1] *** MOUNTED - Sending event out, device session 0.
    [SERVICE: 0x52C,09:43:04 INFO] [1] Auto-launch iTunes DISABLED
    [SERVICE: 0x4F0,09:43:11 INFO] [VolumeArrive] mask = 0x10
    [SERVICE: 0x4F0,09:43:11 INFO] looking up device # for \\.\E:
    [SERVICE: 0x4F0,09:43:11 INFO] type 0x7 drive 0x1 partition 0x1
    [SERVICE: 0x4F0,09:43:11 INFO] iTunes device #1 found with drive letter E, mask 0x10
    [SERVICE: 0x4F0,09:43:11 INFO] [1] set waiting to mount = 0
    [SERVICE: 0x4F0,09:43:11 INFO] [1] input #22 from src #0
    [SERVICE: 0x4EC,09:43:11 INFO] [1] input #22
    [SERVICE: 0x4EC,09:43:11 INFO] [MACHINE 1 INPUT #22] - (HDW) Volume Mount
    [SERVICE: 0x4EC,09:43:11 INFO] ** CItunesDevice::HandleHardwareInput()
    [SERVICE: 0x4F0,09:43:11 INFO] [DevNodesChanged]
    [SERVICE: 0x4F0,09:43:11 INFO] [1] input #23 from src #0
    [SERVICE: 0xD24,09:43:11 INFO] [1] input #23
    [SERVICE: 0xD24,09:43:12 INFO] [MACHINE 1 INPUT #23] - (HDW) CheckDevNode
    [SERVICE: 0xD24,09:43:12 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
    [SERVICE: 0xF90,09:43:16 INFO] <0x4> Got Serial #
    [SERVICE: 0x200,09:43:16 INFO] <0x4> GetFormatType() returned unknown format 0
    [SERVICE: 0x200,09:43:16 INFO] [1] Progress state is 0, Waiting to disconnect = 0
    [SERVICE: 0x200,09:43:16 INFO] Mounted
    [SERVICE: 0x200,09:43:16 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
    [SERVICE: 0x200,09:43:16 INFO] Device 1 not in intermediate state. It appears to be truly mounted.
    [SERVICE: 0xF90,09:43:16 INFO] Mounted
    [SERVICE: 0xF90,09:43:16 INFO] [1] already mounted!
    [SERVICE: 0xF90,09:43:16 INFO] [1] progress state is 0, Waiting to mount = 0
    [SERVICE: 0x200,09:43:33 INFO] <0x4> GetFormatType() returned unknown format 0
    [SERVICE: 0xD10,09:43:33 INFO] [1] Progress state is 0, Waiting to disconnect = 0
    [SERVICE: 0xD10,09:43:33 INFO] Mounted
    [SERVICE: 0xD10,09:43:33 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
    [SERVICE: 0xD10,09:43:33 INFO] Device 1 not in intermediate state. It appears to be truly mounted.
    [SERVICE: 0xF90,09:43:33 INFO] <0x4> COM request for device 1 drive letter - E
    [SERVICE: 0xD10,09:43:34 INFO] Mounted
    [SERVICE: 0xD10,09:43:34 INFO] Device 0 is FAT32 and appears mounted, checking intermediate state...
    [SERVICE: 0xD10,09:43:34 INFO] Device 0 not in intermediate state. It appears to be truly mounted.
    [SERVICE: 0xF90,09:43:54 INFO] [1] Progress state is 0, Waiting to disconnect = 0
    [SERVICE: 0xF90,09:43:54 INFO] Mounted
    [SERVICE: 0xF90,09:43:54 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
    [SERVICE: 0xF90,09:43:54 INFO] Device 1 not in intermediate state. It appears to be truly mounted.
    [SERVICE: 0x200,09:43:54 INFO] Mounted
    [SERVICE: 0x200,09:43:54 INFO] [1] already mounted!
    [SERVICE: 0x200,09:43:54 INFO] [1] progress state is 0, Waiting to mount = 0
    [SERVICE: 0xD10,09:43:54 INFO] Mounted
    [SERVICE: 0xD10,09:43:54 INFO] Device 0 is FAT32 and appears mounted, checking intermediate state...
    [SERVICE: 0xD10,09:43:54 INFO] Device 0 not in intermediate state. It appears to be truly mounted.
    [SERVICE: 0xF90,09:43:54 INFO] [1] Progress state is 0, Waiting to disconnect = 0
    [SERVICE: 0xF90,09:43:54 INFO] Mounted
    [SERVICE: 0xF90,09:43:54 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
    [SERVICE: 0xF90,09:43:54 INFO] Device 1 not in intermediate state. It appears to be truly mounted.

    If anyone is interested I managed to solve this problem by reformatting the ipod as a mac ipod, with the help of friends system. This does get rid of the music but as I had it backed up wasn't a problem. I then plugged the mac Ipod back into a windows pc and reformatted it as a windows ipod which updated the firmware correctly and have'nt had a problem since.

  • After upgrading to Mountain Lion, my LaCie USB 3 drive will not mount

    I just upgraded my OS to 10.8 and now my LaCie P'9230 USB 3.0 external drive will not mount. I have re-installed the USB driver and re-booted the computer and drive several times to no avail; any ideas/help?

    mrfredmor_65 wrote:
    I just upgraded my OS to 10.8 and now my LaCie P'9230 USB 3.0 external drive will not mount. I have re-installed the USB driver and re-booted the computer and drive several times to no avail; any ideas/help?
    It's my understanding that LaCie hasn't released a Mountain Lion driver for their PCIe card yet. Sonnet uses a modified version of the LaCie driver and theirs is dead in the water too for that reason-they also warn that their driver won't work with 10.7.5 when it's released.
    Indeed, yesterday I pulled the Sonnet USB 3.0 card from my Mac Pro and replaced it with a CalDigit card from OWC; CalDigit has separate drivers for 10.6, 10.7 and 10.8 and I can say that the card works with all three, the first time in 1.5 years that I've had a reliable USB 3.0 connection.

  • How do I repair a hard drive that was being written to while my MacBook Air crashed? (Drive will not mount)

    My external backup drive will not mount. I have tried to mount it in Disk Utility via the app and the command prompt but the attempt times out. Any suggestions?
    I backed up my HD the day before dropping off my Mac for repair, and then tried again just before going to my appointment. During this last and final backup my Macbook Air crashed. I have since discovered that the drive will no longer mount, likely due to the crash that occured during the last attempted backup. I am unsure if the drive can be repaired.
    My logic board was short circuiting some where that controls the headphone jack. Initially this prevented me from using the jack but eventually caused my mac to crash several times before I brought it in for repair. I believe that it is the this crashing that is responsible for my back up not being accessible but that my data may still be intact.
    Thanks for any help you may have!

    If possible, attach it to another Mac and see if it is recognized in Disk Utility.  If so, run Disk Utility>First Aid.  If not, the HDD may be damaged.
    Ciao.

  • Hard drive will not mount shows up in Disk Utility

    I have an external drive with a bootable OS X 10.6.8. I was in a transition between building up a SSD swapped drive. The SSD is installed in the CPU box but I have my old installation running from an external.
    I have several external hard drives. They are all Firewire. Some have USB 3.0 and or eSATA options but my MacMini only talks to Firewire and USB 2.0.
    I understand that you daisy chain Firewire drives and turn them on and off in sequence as they fall from the CPU box/case.
    Firewire is a power source. I run the external with the OS using an AC adapter but one Firewire drive is powered through Firewire.
    I have had as many as 4 external drives running along with the internal drive without a glitch while I was reorganizing files.
    Today I booted off the external drive. It was running fine. I turned on one Firewire drive (the one that runs on Firewire power). That drive stumbled. I recognized the sound when there is an interruption in power. This cause the external boot drive to stall. I had to force a reboot.
    Now the external boot drive will not boot up. It does not mount but Disk Utility sees it. The drive itself is bright and clear in Disk Utility but the partition (single) is faded out. I can run Verify and repair in DU. DU says it doesn't see anything to repair. It will not mount on its own or when I click the Mount button in DU. It does not produce an icon on the Desktop (because it is not mounting).
    I also have SpeedTools. But although it sees the drive I cannot do anything with it. None of its tools run more than a spli second before they fail.
    This drive has USB 3.0 and I see everything through USB that I see through Firewire. Connecting the other way did not get around the problem.
    Of course I will buy an AC adapter for every external drive and never run them using Firewire again but the horse is out of the barn.
    I have the original installation disks and could run the Archive and Install option but it would require physically swapping drives with the internal. I'd like to avoid it if possible. It is a MacMini and tedious.
    Any suggestions?

    I took the problematic hard drive and installed it in my Mac Mini so I could attempt a Safe Boot and then Archive and Install if necessary.
    Safe Mode didn't work. The drive produced the circle with a slash symbol.
    I reset the PRAM which was part of a list of steps to work through I found created by Apple Support.
    I was able to boot up to Verbose Mode and view the text of the boot process. I wrote it all down. I can answer questions about the content better than typing it all out exactly. It includes, "...journal magic is bad..." "...failed to open..." and ends with "...cannot mount root, errno = 19"
    I attempted Archive and Install however when it went to show what target drives were available it was a blank box and all buttons were grayed out.
    I rebooted and opened Disk Utility from the DVD. The drive appeared the same with the top main line bright and the partitioned volume faded. Still was unable to mount. I ran Verify and this time a red line of text appeared "Invalid content in Journal" and at the end I ran Repair. When running I could read line by line and at one point it showed "checking volume information" then the following line "Repairing volume" the following line "Rechecking volume" more line of checking then it ended with "The volume was repaired successfully."
    It still would not mount. I ran Verify again and again said "Invalid content in Journal" and this time it stopped midway saying "The volume was found corrupt and needs to be repaired. Error: This disk needs to be repaired. Click Repair Disk."
    I clicked Repair and it ended with The vol. was repaired successfully."
    Still unable to mount I began repeating Repair over and over. Each time it found something to repair and ended with a success message. After several more Repairs I tried Verify and it stopped midway saying to Repair the disk.
    Question: Does running Repair multiple times continue to correct bits and pieces little by little or is this a generic message and we should treat it as a problem Disk Utility cannot pinpoint and is just beating its head against the wall?
    The step by step instructions I downloaded mentioned running Repair more than once but it did not say that running it 20 times would erode some problems and eventually lead to a fully repaired disk (if the problem was something DU could take care of in the first place). At this point I have run Repair about 20 times total with a series of 10 back to back skipping Verify. I keep seeing the lines about invalid content in a journal and that it repaired something successfully. Yet I still cannot mount the disk.

  • Disk Images will not mount and Disk Utility will not runru

    I am having some major problems with Disk Utility, Disk Images, and software update. First, Disk utility will not open or run. When I double-click the application icon, nothing happens, no message, nothing. I am running OSX 10.4.11. I have deleted diskutility prefs. I am able to run Disk Utility from the Startup DVD of Tiger. On first run, it verified and repaired permissions. I run verify and repair permissions several more times from Startup DVD and everything is fine. But Disk Utility on my startup HD will not work. Similary, NONE of my disk images will mount. No matter what Disk Image i try to mount, nothing will. And I cannot use Disk utility to mount them! So, no matter what I download, no images will mount. And thirdly, when I try to run software update, it will not work. I do get a message: it says, "Could not load Software Update." Finally, i tried to download Onyx to delete log files, etc.. but again, the disk image will not mount. I was able to install a dashboard widget called "maintidget" and was successful in running the daily, weekly, and monthly maintenance tasks. Can anyone help? Everything else works fine!!! All apps! Safari, Mail, iTunes, MS Office, everything works fine. Thanks for ANY help!

    Previously, I had run verify permissions, repair permissions multiple times(from startup DVD) - no probems found. Deleted disk utility prefs. Run the maintenance taskes (daily, weekly, monthly). Nothing worked. But, I forget to check the drive for problems. So I ran disk scan. It found "invalid node" and repair disk could not do it. So, do I erase and do a fresh install or get DiskWarrior? I am running Leopard so I do not have Time Machine but I have backed up my documents, iTunes Library, iPhoto Library, etc... Another thing I found out the hardway is to sync all your bookmarks, mail settings and messages, etc... with .mac if you have an account. Any more suggetions?

  • Bootcamp Partition Will Not Mount - Size Bootcamp Partition Will Not Mount - Also Size Discrepancies

    I have bootcamp installed on an internal hard drive in my Mac Pro running 10.8.5.  This HD had two partitions, one of which I had 200GB allocated for my Windows install.  I reached a point where I was at nearly 100% capacity on that drive and needed more room.  This is what I did:
    Used Disk Utility to shrink the Mac OS Extended partition.
    Erased free space on that partition.
    Booted back into Windows and used MiniTool to extend the bootcamp partition to unallocated space.
    MinoTool then performed a restart and finished it's job upon startup.
    I am still able to boot into Windows and Mac just fine and I did create a backup of each OS before starting.
    I have two issues now, however.  Parallels no long recognized that Bootcamp partition.  I decided to delete that VM and I had to uninstall Parallels completely anyways due to an upgrage isse to Parallels 9.  After upgrading, Creating a VM from my BC was not an option.  This is because the BC partition will not mount, it is greyed out in Disk Utitlity.
    I tried installing Tuxera NTFS and the disk still cannot be mounted. 
    The other issue is that Disk Utility does not show the Bootcamp partition with the correct size.  It still shows it with the original 200GB but does show that the Mac Partition was shrunk.  In Windows, however, either using MiniTool or Windows Disk Managment, it shows the correct sizes for the partitions.
    I'll attach a screenshot of DU.
    I would like to be able to mount the drive successfully so that I can use the partition once again for Parallels.
    This is the system.log display when attempting to mount the BOOTCAMP partition and when disabling Tuxera from the system preferences:
    Nov  7 08:35:46 ***-mac-pro.local com.apple.SecurityServer[27]: Succeeded authorizing right 'system.volume.internal.mount' by client '/Applications/Utilities/Disk Utility.app' [973] for authorization created by '/Applications/Utilities/Disk Utility.app' [973] (100013,0)
    Nov  7 08:35:46 ***-mac-pro.local com.apple.SecurityServer[27]: Succeeded authorizing right 'system.volume.internal.mount' by client '/usr/sbin/diskarbitrationd' [15] for authorization created by '/Applications/Utilities/Disk Utility.app' [973] (100002,0)
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS driver 3.10 [Flags: R/W].
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS volume name BOOTCAMP, version 3.1.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_lookup_inode_by_name(): Directory index record with VCN 0x3 is corrupt.  Corrupt inode 0x5.  Run chkdsk.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_windows_hibernation_status_check(): Failed to find inode number for hiberfil.sys.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs warning (device /dev/disk3s3, pid 5414): ntfs_system_inodes_get(): Failed to determine if Windows is hibernated.  Will not be able to remount read-write.  Run chkdsk.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_attr_find_in_attribute_list(): Base inode 0x9 contains corrupt attribute list attribute. Unmount and run chkdsk.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_inode_read(): Failed to lookup data attribute.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_inode_read(): Failed (error 5) for inode 0x9. Run chkdsk.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_inode_attach(): Failed to load inode 0x9.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_secure_load(): Failed to load $Secure.
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_mount(): Failed to load system files (error 5).
    Nov  7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_mount(): Mount failed (error 5).
    Nov  7 08:35:48 ***-mac-pro.local com.apple.SecurityServer[27]: Succeeded authorizing right 'system.privilege.admin' by client '/Applications/System Preferences.app' [5297] for authorization created by '/Applications/System Preferences.app' [5297] (100012,0)
    Thanks,
    Josh

    Josh,
    I will defer to Christopher on correcting the GPT, but I agree it is incorrect. On a much simpler, single disk Macmini with Bootcamp...
    sudo gpt -r -vv show /dev/rdisk0
    gpt show: /dev/rdisk0: mediasize=500107862016; sectorsize=512; blocks=976773168
    gpt show: /dev/rdisk0: Suspicious MBR at sector 0
    gpt show: /dev/rdisk0: Pri GPT at sector 1
    gpt show: /dev/rdisk0: Sec GPT at sector 976773167
          start       size  index  contents
              0          1         MBR
              1          1         Pri GPT header
              2         32         Pri GPT table
             34          6        
             40     409600      1  GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
         409640  725093952      2  GPT part - 48465300-0000-11AA-AA11-00306543ECAC
      725503592    1269536      3  GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
      726773128        632        
      726773760  249999360      4  GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
      976773120         15        
      976773135         32         Sec GPT table
      976773167          1         Sec GPT header
    sudo fdisk /dev/rdisk0
    Disk: /dev/rdisk0          geometry: 60801/255/63 [976773168 sectors]
    Signature: 0xAA55
             Starting       Ending
    #: id  cyl  hd sec -  cyl  hd sec [     start -       size]
    1: EE 1023 254  63 - 1023 254  63 [         1 -     409639] <Unknown ID>
    2: AF 1023 254  63 - 1023 254  63 [    409640 -  725093952] HFS+       
    3: AB 1023 254  63 - 1023 254  63 [ 725503592 -    1269536] Darwin Boot
    *4: 07 1023 254  63 - 1023 254  63 [ 726773760 -  249999360] HPFS/QNX/AUX
    diskutil list /dev/disk0
    /dev/disk0
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:      GUID_partition_scheme                        *500.1 GB   disk0
       1:                        EFI EFI                     209.7 MB   disk0s1
       2:                  Apple_HFS Macintosh HD            371.2 GB   disk0s2
       3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
       4:       Microsoft Basic Data BOOTCAMP                128.0 GB   disk0s4
    PS: I see Christopher's response.

  • Hard drive will not mount with 10.4 but will mount with 10.3

    I have a G4 powerbook running on 10.4.11. There is a western digital my book external drive hooked up to the USB port. I have two partitions on it. I tried to change the group settings to read write and got an error saying I did not have permission. Now the first partition will mount, but the second which I tried to change will not mount.
    Disk utility sees the drive but it is grayed out. DiskWarrior sees the drive.
    I dragged out my old G3 running 10.3.9 and plugged it in. Works great. The disk drive partition mounts and all of the files are there. What do I need to do to get 10.4.11 to mount the disk partition?
    The external drive is a Western Digital My Book 250G divided equally into two partitions. The partitions are in Mac extended format.

    I'm having pretty much the same problem... Have a WD 500 GB external attached via USB. I can't say for sure that the WD caused this (wasn't paying close enough attention), but I've noticed that my own MacBook HD is no longer mounted. I can't seem to find anyway to accomplish this either. I've booted from another volume to run Disk Utility (repair/verify). I rebooted with the MacBook startup drive and still, no HD. And NOW I can't see the bootable partition I made on the WD external. What?
    I feel like the opposite of a nerd, cuz I'm just scratching my head at this point. Oh yeah, and running 10.4.11...

Maybe you are looking for

  • Problem with Display card of Probook 450 G1

    Hello I have just bought Hp probook 450 G1 and i have installed all mandatory drivers from HP site , but now i am facing a problem with the display cards .I tried it n PES 13 Game , it says that my device is not apprpraite  , also it reads the AMD ca

  • Purchase Order History in smartform

    Hi gr8 minds I have developed smartform for purchase order . now i wanna develop amendment purchse order . any idea how to go for it . thanks & regards siddharth

  • Logic Pro audio error 10011 (drop out)

    I bought a new mac mini yesterday that meets all requirements for Logic. I bought it to run Logic as a dedicated machine linked to a keyboard. Apart from the basic software that came with it, Logic is the only software installed on it. Installed it a

  • Safari won't open! A) How to fix it  B) How to access the internet w/o it?

    I've posted this question on other threads but I guess I have to post a new thread marked as a question, so here goes, with the first part of my error report, as it was too long to fit in one thread: Date/Time: 2009-04-06 07:19:37 -0400 OS Version: 1

  • Broadband is unacceptable!!!! i want to leave NOW!...

    i have had bt vision for 5 months i thought i was getting a good service. everything was a hunky dory for about a month untill i started to get V04 error this is due to the fact that my internet isnt quick enough. i also have a problem which online g