Firewire analog video conveter isnt recognized

hello,i have analog video converter dazzle hollywood dv bridge, i can see video from it in imovie, and record it..but i need to see it in quicktime, it shows it in devices, and lets me start recordin, but it shows just black picture, thx for the help...

FME should support audio and video from Firewire
source.

Similar Messages

Audio bad: Sony analog video, RCAs into converter, firewire into PowerBook

Using iMovie HD 5.0.2 and OS X 10.4.9 on a PowerBook G4.
Importing video from a Sony analog video camera by running an RCA cable for video and an RCA cable for audio from the Sony camera into a Formac converter. From the converter I run a FireWire line into the PowerBook. With this set-up, iMovie captures the video okay, but the audio is only a rapid buzz; sounds like a perfectly regular square wave.
I can confirm that the audio signal is being sent from the Sony camera through the converter and on into the FireWire cable by using the same hardware set-up but using Final Cut Express to capture the movie. But I don't want to work in FCE, I want to work in iMovie.
What might be going wrong with the audio capture in iMovie?
several Mac OS X (10.4.9)

Welcome to iMovie Discussions.
As far as I remember, some of the Formacs (..I've never used one, but there was talk of this here..) exhibited this "chainsaw buzz" around the time that iMovie was upgraded to Version 4, I think.
(..Something to do with Formac's non-stringent interpretation of the Firewire spec, perhaps..)
Formac did post info about it on their website, and offered two kinds of upgrade; a firmware download/upgrade for some models ..which you could do yourself.. and a factory upgrade for others.
I don't know if they still offer either of these options, sorry..

Capture analog video audio for MacBook

Is there an inexpensive way to get analog video and audio in/out using my MacBook? I'll be using Final Cut Pro 5.1 Studio to edit. Most of my media will be from my BetaCam SX camera. I will be exporting to DVD, Beta and who knows what for broadcast and internet. Thanks for the help. Gary
MacBook
MacBook

The cheapest viable choice you have is to go DV-rez for your project. All you'll need is a Firewire breakout box such as a Canopus, Pyro AV, or other similar box - they usually cost around the $200 mark.

Bad audio connection on P-35 Platinum moBo, while capturing analog video?

Before I give up, I'm reaching out to MSI and any persons suffering from out-of-sync audio and video capture issues while using Pinnacle Studio Video editing software. Studio Ultimate HD v.14.
I've posted numerous inquiries to the Pinnacle Support team, the Pinnacle Forum site, as well as the GrassValley (Canopus 110 or 300, I was thinking about trying that) and really never got anywhere.
A few people had mentioned maybe the sync issue could be caused by a bad analog signal and it will drop video or audio frames hence the sync problem. Bringing the video into the capture mode in Studio is fine, but the audio has about a 6 second latency delay, which never recovers.
Could it be the REALTEK HD Sound Audio on my P-35 MoBo, maybe bad? I play music, and everything else coming out of my speakers sound fine, it's just the syncing issues with a PCI device that never locks in both the Video with the audio, because there are two different incoming devices. Analog camera video-out to PCI Video-IN, and audio out from analog camera to onboard, MoBo Realtek audio input.
The PCI-500 capture that originally came with my first Studio product (Studio movieboard 12.1) has NO Audio RCA input, only FireWire, S-video, and Video IN and OUT)
P-35 Platinum MS-7345 Mobo
Windows XP Home Edition SP3
Intel Core 2 Quad CPU Q6600 @ 2.40GHz (4 CPUs)
2.4 GHz, 3328 MB Physical RAM
NVIDIA GeForce 8600GT 512 Memory Size
Realtek HD Audio Output Sound
DirectX version: 9.0c
Monitor: Viewsonic VX2035wm Series
WD 500 GB HDD / WD 74GB RAPTOR HDD
Pinnacle PCI-500 Capture card
Nero9
I use the MSI Live Update 4 to update drivers, BIOS, VGA,and Utilities. This system is about four years old. I'm just afraid to flash or update BIOS, thinking I could screw things up.
So I guess my question here is to ask, if maybe the audio input jack on my P-35 Mobo could be defective? Thank you!

Have you try out with a standalone add on sound card? Sometimes, sync problem can be due to processing power or RAM space needed for rendering and merging.

Converting old analog video with maximum resoultion for archieving and eventual use in iMovie

There seems to be a lot of information on converting old (amatuer) analog video media to a digital format, and which one is best to preserve the maximum amount of data. I have already imported old VHS, analog 8, hi8, and dv into iMovie interations from iMovie 6 and forward. The later versions seem to convert the older files to their own format, I suspect, with a loss of data. I want to reimport the old media to create masters in the best digital format for eventual editing by iMovie 11, or whatever iMovie comes after that.
I have the following formats: VHS, super VHS, 8MM, Hi8, DV, and a memory card (from a camera which is not directly compatible with iMovie 11)
I have the following equimpent:
SONY dual deck VHS DVD. This allows me to convert VHS directly to DVD. I can later decode using Handbreak, and import etc. but it seems I would be losing quality.
SONY Digital 8 handicam. This will play analog tape and output a digital file. I do not know the quality of the output.
Canon VIXIA HFS100, HD camcorder. This uses memory cards. It is NOT compatible with iMovie 11, which I should have checked before I bought it. I have played around with the memory card and have been able to import video but, I do not know the quality, and I've forgotten how I did it.
MacBook Pro, about 4 years old, with a 2Ghz Intel core duo processor and 2GHz Ram. This is obviously not state of the art. I am willing to upgrade within the Mac family but I don't what to upgrade to for my purposes
Canopus ADVC 110. This as DV out via a firewire port, and a DV in/out. It also has svideo in, and composit in.
I have the following software:
iMovie 6, iMovie 9, and iMovie 11. I am fairly comfortable with each version.
Final Cut Express, circa 2006. I would have to learn this.
Handbreak. I use this to rip the DVDs I made with SONY deck. It outputs all kinds of video codecs but is obviously working with compressed imput files. I don't know if I could get it to accept input directly from one of the cameras or the Canopus.
Audacity. I'm using this to combine audio tracks from various sources to add commentary to silent videos, which i would like to add as a voice over track to my iMovies
Toast. I think this can convert files of one video format to another in the process of copying.
Thanks for any advice on any part of this question.
Steve B

Yes
I found a program but am experiencing lots of trouble with it. I was hoping that others could give me a better suggestion.
I've actually downloaded and installed ffmpeg but the problem I'm experiencing now is that the videos do not convert. The program starts to work and then three seconds later I get the dialog box that says everything has been converted but the file created is 0KB and of course will not open.
Any ideas about what could be going wrong? I've attempted to convert the files to different formats and try converting different files as well. I still have the problem.

Getting analog video over DVI

I have a Samsung monitor connected to my 17" Macbook Pro using the Mini-Display to DVI adapter and a DVI cable. However, I believe I'm somehow getting analog video converted to a digital signal. I believe this because:
1.) The picture is noticeably not as sharp. It looks like analog video.
2.) If I reboot in Windows (via BootCamp) I get a much sharper picture - looks like digital video
3.) When the OS X first boots up I get static on the monitor, like you get on an analog TV when you can't get the station.
Anyone have any ideas about how to tell OS X to output digital video? Do I need to install a driver for the monitor?
Thanks.

Hi igril,
both apps, iM and iDVD, expect signals via firewire; both apps using this standard, because a) it is more reliable then usb and b) the specs of fw allow a "generic" set of protocols to remotely control devices (a usb connected camcorder needs "drivers").
b) 30 frames per second in realtime into 768x576 pixles plus color info plus audio with a sampling rate of 44.1Khz... just simple A/D .. ehm, well...
in the PC market you find some cheapo usb "sticks", claiming to digitize.. but with a much smaller res...
Apple decided in meaning of simplicity, convenience and quality, not to go this route...
inexpansive? ebay some used miniDV with analogue-in or an old Formac box...

Best Ideas for Analog video...

I'm doing a low end high school football team video.
Unfortunatelly it was shot by a parent that doesn't have the latest camera technology. It was shot in analog video.
I looked into some Analog to Digital Video converters. http://www.nextag.com/CHANNEL-SOURCES-XITEL-INPORT-60374928/prices-html?nxtg=940 0a200507-A19F9E70CC1E7C04 - was looking into this one, just seeing what you guys think.
I can't transfer the video from camera to camera, because my camera doesn't support an input. It's being done across state so I'll be using my old analog camcorder and maybe using that converter in the process.
What are your thoughts?

Benny,
I don't think you need a TBC (time base corrector). As I understand it you just need to get the parent's footage into your mac via firewire.
There are a number of ways to succeed at this. Probably least expensive is to dub (make a copy) of the parent's tape to a DV tape (I assume that's what your camera is). Use RCA cables to dub from the parent's camera/deck to any DV camera or deck that will accept RCA cables. Once it's in DV you're back in business.
Yes, you could also use an A to D converter but I don't think that'll be necessary (I'm trying to save you money without losing quality).
Just borrow a basic DV deck, or even a DV camera that'll allow you to make the dub. You might be able to get a local video production company to help you; you can thank them profusely in the credits.
I hope this helps,
Craig

Importing analog video using MovieBox DV

I purchased a Pinnacle Studio MovieBox DV Version 9 last February at my local Apple Store. I want to convert old analog videotape to movies in iMovie HD. I'm finally getting around to using the MovieBox, but it's not working. I have a Sony CCD-TRV87 Hi 8 camcorder hooked up to the MovieBox, and the MovieBox firewired to my Mac OS X. The iMovie screen indicates "Camera Connected". When I press "Play" on the camcorder, it plays -- but not on the screen. I realize I need to control the camera with its buttons and not iMovie's. The Apple Store employee I spoke to today said that the cords used to hook up the camcorder to a TV should work just fine hooked up to the MovieBox, but do I need an "S" cable? I am at my wits' end fighting with this, as the MovieBox was an expensive piece of equipment, and I just opened the box. Pinnacle doesn't offer anything but "live chat" for support, and just as I reach #1 in the queue, the session cancels. Funny joke! The "Import" button under "File" is grayed out; I can't even make a "Magic Movie" since the Mac is not communicating with the camera. I bought my Mac a year ago, and have only used it to make two movies, which I've since removed from the hard drive to free up space. What am I doing wrong? Does anyone have any suggestions?

Hello,
Like yourself I purchased the MovieBox some time ago from Apple, to convert analog video tapes to DV and am now finally getting around to working with it. My problem is getting it to transfer the data without timecode breaks. I decided to take a closer look at the "manual" which is limited on information (there is no Mac support on their website) and learned the following; there are 2 DV ports. A & B. A is where the Mode Select switch is. Here is where you select the mode you are working in. If you are using s-video then you select that by pushing the mode button until the LED lights up on that connection. Same goes for firewire transfer mode and composite mode. The one thing you need to know is if you are using s-video, you have to connect the audio connections of the composite cable to get sound (white & red as indicated by the music note graphics on the box) I'm not clear on how the connection to the computer works with the firewire. The manual is confusing in this area. I will have to play with it to figure this out. My guess is, since I'm converting to DV that My VCR should be connected to port B and the firewire to my computer on port A. We shall see...
Hope this helps.
Good Luck

Captured analog video, where does the actual captured file go?

I am backing up old analog video 8 tapes to digital, using a Canopus ADVC-55 converter. The process is going just fine as far as I can tell, but I am sure I will have more questions as I get into this further. I am using FCP 6.04.
As an initial test, I completed a Capture Now (non-controllable device selected) of a short 30 min. analog tape, using an older video 8 Sony Handicam, running through the Canopus interfacing with FCP. Primarily I want to run through all these old tapes (about 15 of them…) and back them up onto a dedicated Iomega external firewire drive, to retrieve for later use.
Question du jour… Where the heck is the actual data file on the hard drive? Isn’t the file I see in the bin, from a result of the capture, just an alias pointing to the actual captured data file? The FCP document is only 24 KB, but I know the data file is much larger. I have searched the drive high and low but cannot locate it… Can anyone answer this? Also, I’ve read in discussions here about doing transfer to DV (I have a Canon digital camcorder I could use) rather than the hard drive… but if this is for backup purposes only, should that matter? And wouldn’t I lose a step of quality that way?

I understand Kevan. For the time being, all I wanted to do was get these old 8 mm tapes backed up to digital format because I am afraid the tapes will degrade. They are about 12 years old. I also have some VHS cassettes that are much older that I plan to back up also.
Eventually I would like to build some family movies and will use these files, but if you think I should be capturing into DV (I can use my Canon DV camcorder I guess) I will do that instead.
Also, I will go ahead and define the folder so I can find the files more easily in the future.
I sure appreciate that you are taking the time to answer these questions, thanks again.

Trouble capturing analog video using Quicktime 7 in Yosemite

I am attempting to use Quicktime 7 Pro under Yosemite to convert old 8 mm or Hi8 analog videotapes to digital .mov files. The tapes are being played through a Sony TRV350 camcorder, which digitizes the analog video, and outputs digital video via the iLink (Firewire) output, which then goes to the Thunderbolt input on my MacBook Pro using an adapter. I start the camcorder and then start QT7 Pro.
This DOES WORK - for a short while. After taking in 32MB of data or a minute (of a 90 minute video), QT7 stops capturing data with a message:
"Recording stopped because the format of the source media changed. Media of different formats cannot be recorded to the same file"
What does this mean and how do I get around it?
PS: There are not many ways to convert these old tapes. Under Yosemite iMovie will no longer accept video from a Hi8 camcorder. There is some discussion of older iMovie HD but this does not work properly under Yosemite at all.
Need to digitize these old family tapes - any help will be appreciated

One tiny wrinkle is that "Save" from Vidi gives an error message but "Save as" works fine. I suspect Vidi may also stop working with the next OS X release.
Since you did not indicate the specific nature of the error message, I don't know if this is a "fixable" problem or not. The difference between the "Save/Record" and "Save As.../Record As..." options is that the former automatically stored the captured files in a designated location using a default filename. You may wish to check or reset the preference settings here to see they are causing your issue.
Yes, the conversion of a 90 min tape does give a 21 GB file but I don't care - these family videos are irreplaceable and storage is cheap.
This sounds about right—i.e, the normal average DV-25/DVCPRO-25 total data rate is on the order of 28.5 Mbps (or about 13 GB/hour) with DV-50/DVCPRO-50 about 57 Mbps and DV-100/HDV about 114 Mbps.
One more question. Now that I have a DV file, what can I use to convert to a more compressed format that preserves quality? QT7 to save as H.264 is best? Or something else? Toast?
This normally depends on your goals and personal workflow preferences.
For instance, if you are editing content (i.e., trimming; merging; adding titles, fades, transitions, effects, etc.), I would normally use the export/share options that are available from within the editing app itself. On the other hand, for simple trims and export/share of files, I would normally use QT X or QT 7 Pro depending on the specific project needs and/or level of manual control desired. For totally edit-free conversions, I would normally use the encoder options now built into Yosemite (or Mavericks) operating system at the Finder level or the free HandBrake app. (The former basically employs a non-anamorphic approach with high/low quality or target device controlled quality options while the latter has a better graphic user interface for anamorphic strategies with more manual control for truly customized exports as needed.)
EXAMPLE 1: The family normal has Thanksgiving at my brother-in-laws home in PA so my son hosts a second "pseudo-Thanksgiving" dinner on January 1st for the relatives here in NJ. This year I wore a GoPro and within minutes of returning home created the following "trailer" of the gathering (with a total absence of any real planning or forethought) using iMovie to shared the file directly to Mail for posting to others. In this case, I used the video editor to both edit and share a "quickie" video with the rest of our relatives from the East to West Coast. I.e., it seemed the most efficient workflow for the mini-project... SAMPLE VIDEO
EXAMPLE 2: On the other hand, several yeas ago I was asked to post a "quickie" tutorial showing how to layer audio and video content. As this was a relatively simple project, I used QT 7 Pro for this project. Here is the resulting SAMPLE FILE created while making the tutorial.
EXAMPLE 3: In cases where the quality of the source file varies drastically—one video being an 80 year old cinema classic and the next a just released blockbuster loaded with special effects—and/or the source files are not "natively" compatible with QT, I prefer HandBrake for its ability to "tweak" settings over a wide range to create "universal" playback files for all mobile devices, local network streaming, and sharing via internet... SAMPLE 1959 TRAILER
EXAMPLE 4: Lastly, when I simply want to just transcode one or more QT compatible files (for any number of reasons) at the Finder level without having to open a dedicated converter utility, I simply select/highlight the files in the Finder and pass them to the Yosemite/Mavericks operating system for conversion... POCKET RECORDER SAMPLE FILE
As you can see, you have a myriad of options to choose from depending on your personal preferences, needs, goals, etc. As to H.24/X.264/MPEG-4 AVC, yes I would recommend sticking with any encoder that adheres to the JVT standard since it has become a default Mac system standard and, with different settings, is extremely scaleable with regard to use—i.e., it can handle anything from cellular streaming to Blu-ray or multi-K Hi-Def resolutions. However, for all-purpose use, I stick to High Profile (current mobile, TV, High-Speed Internet compatible) or Main Profile (older mobile device, original TV, lower-speed platform compatible) anamorphic encodes at level 3.1 which nicely covers data rates from less then 100 Kbps up to 14 Mbps or anything most users will ever need.

I was advised to purchase dazzle video creator to move analog videos from an old sony camcorder to a mac. I have purchased the dazzle and the specs seem to be for windows only. Has anyone used this product on mac?

I was advised to purchase dazzle video creator to move analog videos from an old sony camcorder to a mac. I have purchased the dazzle and the specs seem to be for windows only. Has anyone used this product on mac?

I am not certain, but I believe there is a version of Dazzle for the Mac. However, it is not the route I would chose.
You really need a proper analogue to digital converter, like the ADVC110, to connect to your camera via the usual RCA cables, and to your Mac via firewire.

Importing analog video intoMac mini or MacBookPro

I have a VHS-C camcorder & a Hi-8 camcorder. I also have VHS tapes. I have a VHS-C to VHS adapter. I think that the Hi-8 has S-video out. So I'd need something external that will convert an analog signal into a digital signal. I want to import the videos into my computer & edit them. I have a VHS to DVD burner but it is in a separate room. Is there any hardware that will convert analog video tapes into digital video that I can hook up to my mini or MBP & import the videos so that I can edit them? Is the equipment reasonably priced?

You may find that, importing the VHS tapes directlly into the Mac Mini is easier because it's lacks a SuperDrive.
I have a SuperDrive. There aren't that many connections on my mini. The Thunderbolt port is available as well as the Firewire port. The external hardware usually has a USB output. I don't know if any have a Thunderbolt or Firewire output. I suppose that I can get a USB to Thunderbolt adapter.
After I posted the message, it occured to me that I already know the answers to my questions. DUH! I need both the hardware to connect my camcorders to my mini or MBP plus I need the software. I've browsed around iMovie. I can import my videos & use it to edit my videos. I have a VHS to DVD burner in the living room. I can use the external hardware to connect my MBP to the VHS machine.

Importing Analog Video via Canopus ADVC300

When you Import video if there is a glitch in the video tape playback the imovie import stops. So if you have a an older video tape and it drops out the import stops. Is there anyway to for the import to stay running without the input affecting it?
The Canopus 300 is a analog video to firewire converter. It does a great job otherwise.
Thanks,
Andrew

Hi
in iMovie HD 6 - I set it to not import as individual clips.
• there are non in analog import
• turning it off makes iMovie less sencitive to drop outs
Cheque Your Canopus ADVC-300 manual. Think I set it so that it's not so
sencitive to drop-outs. But may be I'm wrong in this.
Yours Bengt W

Convert analog video to digital using a miniDV camcorder

Hi hi
So I want to convert some old analog videos I have from about 10 or so years ago to digital so I can edit them in iMovie HD. I've been reading a lot of the forums around and have successfully (I think) connect the analog video camera to the the miniDV (a Sony Handycam DCR-HC30E) using that A/V jack in the digital recorder and the analog to connect them. And the digital recorder is connected to the computer via firewire. So that's all right.
But now I'm up to the stage where I need to import it into iMovie HD (version 5.0.2) and it's been stubborn and not doing anything. I press play on the analog like people have said but iMovie just says "Camera no tape" and the "import" is unclickable.
Please please please please help! I've no idea what I'm doing wrong!
So just for quick reference, I'm using:
iMovie HD 5.0.2
Sony Handycam DCR-HC30E (Mini DV) and
Panasonic NV-VZ1 (analog video recorder)
P.S I don't want to have to record onto the the mini DV tapes because I've got none.
Thanks!

Hi catspaw! Thanks for replying
I probably should have mentioned before that I did change the 'A/V to DV out' to on, and I think that's the same as "passthrough"
And I've tried suggestion 2 as well, but to no avail! The connection either dropped once I took the tape out or it started to film on my iSight camera! Which is bizarre because my iMovie usually does not let me film with it! I've also been able to film with the camera connected to the computer and recording on the computer and see what I'm fliming on the computer.
But thanks for your help anyway!

How to import an analog video to Photoshop Extended Cs5?

I'm a beginner, I'm trying to restore an analog video from a vhs tapes. I'm using Adobe Premiere Cs5, and would like to know what format to convert an analog video to import it into photoshop.
Gerald Sr.

I'm not sure that I really understand the question
If you have Premiere Pro for video editing, why are you trying to import a video file into Photoshop?
To convert VHS analog to computer digital you need to have a Firewire port in your computer, and use a digitizing device such as from http://www.grassvalley.com/products/converters
That will create DV AVI video which you edit in Premiere Pro

Firewire analog video conveter isnt recognized

Similar Messages

Maybe you are looking for