Firewire cable MacBook to iMac

What type of firewire cable do I buy to transfer data from my MacBook3,1 to my brand new iMac?
I have a cable that fits my MacBook but not my iMac.
Thanks
Message was edited by: judobscure

you can either get the 6 pin to 9 pin adapter, or the 6 to 9 cable.
I like the cables better the adapter is smaller, easier to lose, & creates a long, stiff joint prone to breaking should something fall or pull the cable.
http://eshop.macsales.com/search/firewire400+to800

Similar Messages

  • I have a Sony Camcorder DCR-TRV33 and have hooked the firewire cable to my iMac.  However, it doesn'

    I have a Sony DCR-TRV33 camcorder and it hooked to my iMac with the firewire cable but the iMac doesn't seem to recognize the camera.  The camera is set to VCR.  This particular model is not included in the supported camera list for ilife but seems to be compatible from everything else I have read.  Anyone have any ideas as to what to do??

    To import from this camera, you need a Firewire cable.
    Sony's name for FireWire is i.Link, so that is where you need to plug in.
    If you have a relatively new Mac, it will have Firewire 800. You will need a 9 pin to 4 pin Firewire Cable. You can find them inexpensively at www.monoprice.com.  If you have an older iMac, it may have Firewire 400 (or it may have both). In this case, you need the  6 pin to 4 pin Firewire cable. Some companies sell adapters that will convert a 6 pin to 4 pin cable to 9 pins. Avoid these. They do not work.

  • What cable do I need to hook a 4 pin firewire cable into an iMac (21in late 2013)

    What cable do I need to hook a 4 pin firewire cable into the back of an iMac (21in late 2013)?

    One of these:
    Thunderbolt to Firewire Adapter
    http://store.apple.com/us/product/MD464ZM/A/apple-thunderbolt-to-firewire-adapte r

  • 4-Pin to 6-Pin Firewire cable into new iMacs?

    Hi,
    I have the new 27inch model iMac and as we know they have no firewire ports. I've got a Firewire to Thunderbolt adapter for my two external Firewire 800 hard drives.
    Question is I have my old Mini DV camcorder that I used to plug in with a 4-Pin to 6-Pin Firewire cable. How do I go about gettinbg this camcorder hooked up to the new iMac?
    Thhis was the cable I used to use:
    Thank you for any assistance.

    Here checkout these Thunderbolt to Firewire adapters.
    http://store.apple.com/us/browse/home/shop_mac/mac_accessories/cables
    and these...
    thunderbolt to firewire

  • What type of firewire cable for 2006 iMac?

    I asked at Best Buy and they gave me 4pin, didn't work. I looked online and got 9 pin, it fits the MBPro we're trying to connect the iMac to but not the iMac. So I know I need a 9pin for the MBPro but what should the other end be? Everything I saw online said 9 pin but its clearly not even the right shape to fit the port on the back of my computer... FWIW, I'm trying to connect to the MBPro so we can boot from their HD and install a new OS on our computer becuase the cd rom drive on mine is broken.

    You need a cable like
    http://www.amazon.com/Oyen-Digital-Firewire-1394B-Cable/dp/B0027DPM1U/ref=sr_1_1 ?ie=UTF8&qid=1319759339&sr=8-1
    You should be able to get one at BBY, RadioShack, Fry's Electronics or of course Amazon.

  • What Firewire cable for latest iMac?

    Hi,
    I am a bit confused that my Firewire doesn't fit into my new iMac (2011 model i3).
    After a bit of Googling, I notice there are different pin amounts (4,6,9).
    Which one do I need to connect my DV Video Camera to my iMac??!!
    Thanks in advance

    Your choice. I prefer the cable with different ends. However, this should also do the job: http://www.amazon.com/Sonnet-FireWire-400-Adapter-FAD-824/dp/B0000CDJPQ

  • I need to boot up a mac book via firewire cable

    I need to start up my macbook via a firewire cable from my imac. is this possible and what cable do I need exactly.

    Boot the iMac in Target Disk Mode: hold the T key during startup
    Use Startup Manager on the MacBook: hold an Option key during startup, and select the iMac's disk.
    You need a FireWire cable with connections that match your hardware, either FW400 or 800 or both.
    This may or may not work, since the OS on your iMac may not contain the correct drivers for the MacBook.

  • Do I need a firewire cable to transfer files to my new iMac?

    Hi, I have a new iMac coming soon and I want to know the best way to transfer my files, settings etc from my iBook G4 to the new comp. We have wireless at home- can I set up some kind of network? Or do I need to buy a firewire cable and use Migration Assistant? If so, which cable? Thank you

    Hmm. I hadn't heard about the problems people have been having. Anyway, yeah, it's probably better to try Migration Assistant with the FireWire cable. From what I've heard (I haven't had to USE Migration Assistant yet; first-time Mac user, and haven't needed a new one yet), Migration Assistant does a good job getting everything switched over, and it's only method is FireWire. So, yeah. LOL. I think that's your best bet.
    I'm so jealous. I have a PowerBook G4 (the model RIGHT before the last model; I should have waited a few weeks!), and now I want at least a MacBook. The cheapest MacBook is now BETTER, in many ways, than my PowerBook, besides the obvious things like screen size. AND it's about half the price I got my PowerBook for. This is CRAZY! Haha.

  • Mid 2010 Macbook Pro battery will not charge after plugging in firewire cable shut down computer

    I have a mid 2010 15" Macbook pro with Lion installed.
    I was running off battery, and I went to plug in a firewire cable, not plugged into anything, and when I inserted it, the computer shut off.
    The computer would not turn on again without being plugged into the AC adaptor. The magsafe charger shows green, but the computer says not charging. The battery is showing 57%, but the indicator lights will only light up when AC charger is connected..
    I have let it sit off, and plugged in for a couple hours, and nothing chages, and let it sit overnight not plugged in, but nothing.
    I have read other forums about the same issue,, it seems like its a common issue, and some have said what it could be, but no one said what it IS.
    I have tried resetting the SMC and PRAM, but to no avail.
    When i plug in the AC adaptor, the computer immediately turns on (which I find kond of funny), and I am able to turn it off normally, and it will stay off, and I can also turn it on if the charger has been connected from pervious.
    Below is my power information.:
    Battery Information:
      Model Information:
      Serial Number:          W0013PVDXBX0A
      Manufacturer:          SMP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          000a
      Cell Revision:          157
      Charge Information:
      Charge Remaining (mAh):          3406
      Fully Charged:          No
      Charging:          No
      Full Charge Capacity (mAh):          5956
      Health Information:
      Cycle Count:          395
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          0
      Voltage (mV):          11638
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          5
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      RestartAfterKernelPanic:          157680000
      Battery Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          3
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
      RestartAfterKernelPanic:          157680000
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          85
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x00b9468c
      Charging:          No
    Any help would be greatly appreciated. Thanks everyone.

    I have a mid 2010 15" Macbook pro with Lion installed.
    I was running off battery, and I went to plug in a firewire cable, not plugged into anything, and when I inserted it, the computer shut off.
    The computer would not turn on again without being plugged into the AC adaptor. The magsafe charger shows green, but the computer says not charging. The battery is showing 57%, but the indicator lights will only light up when AC charger is connected..
    I have let it sit off, and plugged in for a couple hours, and nothing chages, and let it sit overnight not plugged in, but nothing.
    I have read other forums about the same issue,, it seems like its a common issue, and some have said what it could be, but no one said what it IS.
    I have tried resetting the SMC and PRAM, but to no avail.
    When i plug in the AC adaptor, the computer immediately turns on (which I find kond of funny), and I am able to turn it off normally, and it will stay off, and I can also turn it on if the charger has been connected from pervious.
    Below is my power information.:
    Battery Information:
      Model Information:
      Serial Number:          W0013PVDXBX0A
      Manufacturer:          SMP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          000a
      Cell Revision:          157
      Charge Information:
      Charge Remaining (mAh):          3406
      Fully Charged:          No
      Charging:          No
      Full Charge Capacity (mAh):          5956
      Health Information:
      Cycle Count:          395
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          0
      Voltage (mV):          11638
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          5
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      RestartAfterKernelPanic:          157680000
      Battery Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          3
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
      RestartAfterKernelPanic:          157680000
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          85
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x00b9468c
      Charging:          No
    Any help would be greatly appreciated. Thanks everyone.

  • Connecting a MacBook to  PowerMac G5 with a firewire cable

    I have a 13" MacBook. I want to transfer files from my PowerMac G5 running OS X 10.4.11 to it. I can hook an external drive to the MacBook via firewire and it recognizes it. I can hook up the PowerMac and the MacBook via firewire, start the MacBook with the T key depressed and see the hard drive on my PowerMac. But... I can't do the reverse. I can start up the MacBook with the T key depressed and see the G5's hard drive on it.
    Any suggestions?

    Are you using the same cable to connect the machines?
    Some folks suggest to shut both machines down, then connect the Firewire cable. Boot the Power Mac into Target Disc mode. Once you see the FireWire symbol on the PowerMac's screen, try booting the MacBook.
    Once the MacBook has started & you're logged in, check for the hard drive in Finder. If it doesn't appear, open System Profiler (Applications>Utilities), and click Firewire in the left-hand column. Are any devices showing here?
    ~Lyssa

  • I have a MacBook Pro Mid 2012. I have a sony DCR-PC350E . How do i transfer the video to the laptop ? I have firewire cable. But not able to find the firewire port in the video camera.

    Need help.

    The DCR-350e is a miniDV camcorder.  It has a FireWire port, but it's not on the camera itself, it's on the cradle (aka "Handycam Station") that should have come with your camcorder.   You need to insert the camera into the cradle in order to capture video via FireWire.
    Here's a link to the Owners Manual.  See p. 142 for a diagram that shows the DV (iLink) port on the cradle.
    You also need an appropriate cable to connect to your MacBook Pro. Check your MBP to see what port(s) it has:
    Some 2012 MBPs have a FW800 port, in which case you need a 4-pin to 9-pin FW cable like this one. 
    Some 2012 MBPs only have a Thunderbolt port, in which case you need the Apple Thunderbolt-FireWire Adapter in addition to the FireWire cable.

  • Can anyone tell me where to find a firewire cable that fits snug in a macbook pro?

    I have tried many different 9-pin firewire 800 cables. All work there way out of the port on my 2010 Macbook Pro. It's very frustrating because it can ruin the data. Sometimes the repair doesn't work. Most of the time the drive goes offline. The best cable I've found is the firewire cable that came with my Western Digital Passport Studio drive. The cable has metal connectors. It seems to help keep the cable in the port better than any other I've found.
    It's a shame that a firewire lock cable can't be designed for these computers to prevent this problem. Besides tape or glue, does anyone have a suggestion? Perhaps a better cable? The firewire cable that came with my Seagate free agent drive is also quite good. But that cable is proprietary to the drive.
    Thank you for your help!
    Paul

    No one here knows what you have tried in the past.
    The suggested solution was a possibility. One that some folks wouldn't think about. You have already ruled out a new cable as a solution 8 times.
    My mixture of 9 pin FW cables are all snug to the fit - all appear to be different vendors.
    My apologies for having made a 'foolish' suggestion.
    MJ

  • I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

    I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

    Do it with a Firewire cable (buy a 800/400 adapter if you need it) - the USB transfer takes a much longer time.
    Start up your old PowerMac G4 holding down the "T" key, for target disk mode.
    On your new MacBook Pro open "Migration Assistant" in your utilities folder.
    Connect the 2 computers by firewire cable and follow the prompts in Migration Assistant.

  • Can you install tiger on a power mac g4 with out a DVD drive if so how, I do have have a 2011 iMac can I use that in target disk mode with a FireWire cable any help would be appreciated

    Can you install tiger on a power mac g4 with out a DVD drive if so how, I do have have a 2011 iMac can I use that in target disk mode with a FireWire cable any help would be appreciated

    Hello,
    You need to put the Tiger Install Disc in the 2011 iMac, boot the 2011 uMac into Target mode...
    http://support.apple.com/kb/HT1661
    Boot the G4 holding the Option or alt key, hopefully the Install Disc in the 2011 iMac will show as a boot choice.
    We just want to use the 2011 iMac as a big expensive FW Optical drive, it cannot be installed osing the 2011 iMac itself.

  • What firewire cable do I need to transfer data from a 2010 macbook to 2014 macbook

    What firewire cable do I need to transfer data from a 2010 macbook to 2014 macbook

    You would need a Firewire 800-800 (9-pin) cable and a Thunderbolt to Firewire adaptor.
    Matt

Maybe you are looking for

  • Cached Queries and Memory

    I recently learned about the cachedWithin attribute of the cfquery tag. I have found a few places I wish to use this attribute. I am looking at the Caching page of the ColdFusion Administrator and see the "Maximum number of cached queries" is set at

  • How to enter a multi-line comment in the Info editor?

    When entering comments for a song (in Command-I Info), is there an easy way to break the comment into multiple lines? I realize that I can copy-and-paste from a text editor, but (a) it's cumbersome (b) the line breaks don't show in the Comments colum

  • Windows Vista vs Zen Micro: Software Problems

    Hey guys, Looking for a little help and this seems to be the right place to get, lots of helpful people!I have a 3 year old Zen Micro, 4/5Gb I think and it worked fine with my old Dell laptop which ran XP, I used to drag and drop mpg files easily wit

  • Can't find a bootable device after trying to install Windows 7 in bootcamp

    I've been trying to install Windows 7, 64 bit. Haven't managed yet due to problem that I've just posted about in a separate thread. Now, though, when I switch on it says 'can't find a bootable device'. If I switch on whilst holding down the Option ke

  • HT201210 I updated my ipad 1 to 5.1.1 and after that, my ipad shows black screen only, no more

    I updated my ipad 1 to 5.1.1 and after that, my ipad shows black screen only, no more screens, what can i do to fix it,a already tried to recover several times, on three different computers nothing happens